Search NASA⌕ Search

SEARCH · Search NASA

Results for “key performance parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Effect of point defects on the thermal conductivity of UO 2 : molecular dynamics simulations

The thermal conductivity of uranium dioxide (UO 2 ) fuel is an important materials property that affects fuel performance since it is a key parameter determining the temperature distribution in the fuel, thus governing, e.g., dimensional changes due to thermal expansion, fission gas release rates, etc. The thermal conductivity of UO 2 nuclear fuel is also affected by fission gas, fission products, defects, and microstructural features such as grain boundaries. Here, molecular dynamics (MD) simulations are carried out to determine quantitatively, the effect of irradiation induced point defects on the thermal conductivity of UO 2 , as a function of defect concentrations, for a range of temperatures, 300 – 1500 K. The results will be used to develop enhanced continuum thermal conductivity models for MARMOT and BISON by INL. These models express the thermal conductivity as a function of microstructure state-variables, thus enabling thermal conductivity models with closer connection to the physical state of the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Maximum Radionuclide Groundwater Concentrations for Basement Fill Model. Zion Station Restoration Project

The objectives of this report are; To present a simplified conceptual model for release from the buildings with residual subsurface structures that can be used to provide an upper bound on contaminant concentrations in the fill material; Provide maximum water concentrations and the corresponding amount of mass sorbed to the solid fill material that could occur in each building for use in dose assessment calculations; Estimate the maximum concentration in a well located outside of the fill material; and Perform a sensitivity analysis of key parameters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Influence of Process Parameter and Build Rate Variations on Defect Formation in Laser Powder Bed Fusion SS316L

Laser powder bed fusion (LPBF) is an additive manufacturing process that has gained interest for its material fabrication due to multiple advantages, such as the ability to print parts with small feature sizes, good mechanical properties, reduced material waste, etc. However, variations in the key process parameters in LPBF may result in the instantiation of porosity defects and variation in build rate. Particularly, volumetric energy density (VED) is a variable that encapsulates a number of those parameters and represents the amount of energy input from the laser source to the feedstock. VED has been traditionally used to inform the quality of the printed part but different values of VED are presented as optimal values for certain material systems. An optimal VED value can be maintained by changing the key process parameters so that various combinations yield a constant value. In this study, an optimal constant VED value is maintained while printing SS316L with variable key processing parameters. Porosity analysis is performed using optical microscopy, as well as X-ray computed tomography, to reveal the volume density and distribution of those pores. Two primary defect categories are identified, namely lack of fusion and porosity induced by balling defects. The findings indicate that, even at optimal VED, variations in process parameters can significantly influence defect type, underscoring the sensitivity of defect formation to the variation of these parameters. Furthermore, a minor change in the build rate, driven by adjustments in process parameters, was found to influence defect categories. These findings emphasize that fine tuning the process parameters and build rate is essential to minimize defects. Finally, fiducial marks have been identified as a source of unintentional porosity defects. These results enable the refinement of process parameters, ultimately optimizing LPBF to achieve enhanced material density and expedite the printing.

36 MATERIALS SCIENCE↗

Lidar measurements using large liquid mirror telescopes

It is a well accepted practice in the discussion of lidars to compare systems by a performance factor given by the product of the transmitter power and receiver aperture. This form of the performance factor reflects the two key parameters that determine the amount of photons recorded from a given range bin; the amount of transmitted photons and the probability of collecting a scattered photon. We are interested in studying the propagation and breaking of gravity waves typically generated in the lower atmosphere. To study these waves requires high temporal and spatial resolution, as they have frequencies as high as 500 mHz and generate turbulent structures with vertical scales of less than 25 m. In the 80 - 100 km region of the atmosphere these measurements are most efficiently obtained by using resonance scattering from sodium atoms deposited by meteors. However, in the 30 - 80 km region, the most efficient scattering arises from molecules (Rayleigh scattering). Since the atmospheric scale height is nominally 7 km, this scattering becomes extremely weak above 60 km. Furthermore, present laser technology limits the power available for Rayleigh-scattering experiments to about 0.5 - 50 W. The transmitter for the lidar system under development at the University of Western Ontario uses a two-beam transmitter to simultaneously measure density perturbations and temperature from both Rayleigh and resonance scattering.

Sica, R. J.↗

Surface Nuclear Power for Human Mars Missions

The Design Reference Mission for NASA's human mission to Mars indicates the desire for in-situ propellant production and bio-regenerative life systems to ease Earth launch requirements. These operations, combined with crew habitation and science, result in surface power requirements approaching 160 kilowatts. The power system, delivered on an early cargo mission, must be deployed and operational prior to crew departure from Earth. The most mass efficient means of satisfying these requirements is through the use of nuclear power. Studies have been performed to identify a potential system concept using a mobile cart to transport the power system away from the Mars lander and provide adequate separation between the reactor and crew. The studies included an assessment of reactor and power conversion technology options, selection of system and component redundancy, determination of optimum separation distance, and system performance sensitivity to some key operating parameters. The resulting system satisfies the key mission requirements including autonomous deployment, high reliability, and cost effectiveness at a overall system mass of 12 tonnes and a stowed volume of about 63 cu m.

Mason, Lee S.↗

Radioisotope Electric Propulsion Centaur Orbiter Spacecraft Design Overview

Radioisotope electric propulsion (REP) has been shown in past studies to enable missions to outerplanetary bodies including the orbiting of Centaur asteroids. Key to the feasibility for REP missions are long life, low power electric propulsion (EP) devices, low mass radioisotope power systems (RPS) and light spacecraft (S/C) components. In order to determine what are the key parameters for EP devices to perform these REP missions a design study was completed to design an REP S/C to orbit a Centaur in a New Frontiers cost cap. The design shows that an orbiter using several long lived (approximately 200 kg Xenon throughput), low power (approximately 700 W) Hall thrusters teamed with six (150 W each) Advanced Stirling Radioisotope Generators (ASRG) can deliver 60 kg of science instruments to a Centaur in 10 yr within the New Frontiers cost cap. Optimal specific impulses for the Hall thrusters were found to be around 2000 sec with thruster efficiencies over 40%. Not only can the REP S/C enable orbiting a Centaur (when compared to an all chemical mission only capable of flybys) but the additional power from the REP system can be reused to enhance science and simplify communications.

Oleson, Steve↗

COMPASS Final Report: Radioisotope Electric Propulsion (REP) Centaur Orbiter New Frontiers Mission

Radioisotope Electric Propulsion (REP) has been shown in past studies to enable missions to outer planetary bodies including the orbiting of Centaur asteroids. Key to the feasibility for REP missions are long life, low power electric propulsion (EP) devices, low mass Radioisotope Power System (RPS) and light spacecraft (S/C) components. In order to determine the key parameters for EP devices to perform these REP missions a design study was completed to design an REP S/C to orbit a Centaur in a New Frontiers (NF) cost cap. The design shows that an orbiter using several long lived (approx.200 kg xenon (Xe) throughput), low power (approx.700 W) Hall thrusters teamed with six (150 W each) Advanced Stirling Radioisotope Generators (ASRG) can deliver 60 kg of science instruments to a Centaur in 10 yr within the NF cost cap. Optimal specific impulses (Isp) for the Hall thrusters were found to be around 2000 s with thruster efficiencies over 40 percent. Not only can the REP S/C enable orbiting a Centaur (when compared to an all chemical mission only capable of flybys) but the additional power from the REP system can be used to enhance science and simplify communications. The mission design detailed in this report is a Radioisotope Power System (RPS) powered EP science orbiter to the Centaur Thereus with arrival 10 yr after launch, ending in a 1 yr science mapping mission. Along the trajectory, approximately 1.5 yr into the mission, the REP S/C does a flyby of the Trojan asteroid Tlepolemus. The total (Delta)V of the trajectory is 8.9 km/s. The REP S/C is delivered to orbit on an Atlas 551 class launch vehicle with a Star 48 B solid rocket stage

Oleson, Steven R.↗

Parametric Modeling of the Safety Effects of NextGen Terminal Maneuvering Area Conflict Scenarios

The goal of this work was to analytically identify and quantify the issues, challenges, technical hurdles, and pilot-vehicle interface issues associated with conflict detection and resolution (CD&R)in emerging operational concepts for a NextGen terminal aneuvering area, including surface operations. To this end, the work entailed analytical and trade studies focused on modeling the achievable safety benefits of different CD&R strategies and concepts in the current and future airport environment. In addition, crew-vehicle interface and pilot performance enhancements and potential issues were analyzed based on review of envisioned NextGen operations, expected equipage advances, and human factors expertise. The results of perturbation analysis, which quantify the high-level performance impact of changes to key parameters such as median response time and surveillance position error, show that the analytical model developed could be useful in making technology investment decisions.

Rogers, William H.↗

Meta-Analysis of Estimates of Life Cycle Greenhouse Gas Emissions from Concentrating Solar Power: Preprint

In reviewing life cycle assessment (LCA) literature of utility-scale CSP systems, this analysis focuses on clarifying central tendency and reducing variability in estimates of life cycle greenhouse gas (GHG) emissions through a meta-analytical process called harmonization. From 125 references reviewed, 10 produced 36 independent GHG emission estimates passing screens for quality and relevance: 19for parabolic trough technology and 17 for power tower technology. The interquartile range (IQR) of published GHG emission estimates was 83 and 20 g CO2eq/kWh for trough and tower, respectively, with medians of 26 and 38 g CO2eq/kWh. Two levels of harmonization were applied. Light harmonization reduced variability in published estimates by using consistent values for key parameters pertaining toplant design and performance. Compared to the published estimates, IQR was reduced by 69% and median increased by 76% for troughs. IQR was reduced by 26% for towers, and median was reduced by 34%. A second level of harmonization was applied to five well-documented trough LC GHG emission estimates, harmonizing to consistent values for GHG emissions embodied in materials and from constructionactivities. As a result, their median was further reduced by 5%, while the range increased by 6%. In sum, harmonization clarified previous results.

14 SOLAR ENERGY↗

Influence of plasma loading in a hybrid muon cooling channel

In a hybrid 6D cooling channel, cooling is accomplished by reducing the beam momentum through ionization energy loss in wedge absorbers and replenishing the momentum loss in the longitudinal direction with gas-filled rf cavities. While the gas acts as a buffer to prevent rf breakdown, gas ionization also occurs as the beam passes through the pressurized cavity. The resulting plasma may gain substantial energy from the rf electric field which it can transfer via collisions to the gas, an effect known as plasma loading. In this paper, we investigate the influence of plasma loading on the cooling performance of a rectilinear hybrid channel. With the aid of numerical simulations we examine the sensitivity in cooling performance and plasma loading to key parameters such as the rf gradient and gas pressure.

43 PARTICLE ACCELERATORS↗

Bayesian Optimization for Reactor Design Optimization

This study present a test case in which the Bayesian Optimization method is applied to a simulation-based reactor core design optimization problem. The test case aims to showcase the potential of an automated design optimization algorithm for reactor designs by streamlining the reactor core design workflow, given the high computational cost of simulations. The contributions of this work are threefold. First, the existing HTGR model is converted into a simulation-based design optimization test case by developing a pipeline that enables modification of key design parameters and evaluates design performance based on simulation outputs. Second, Bayesian Optimization is implemented and adapted to demonstrate the feasibility of automatic design optimization for nuclear reactor core. Proposed approach leverages Gaussian Process models to characterize the relationship between design variables and performance metrics, while incorporating novel acquisition functions that balance exploration of the design space with exploitation of promising configurations. This implementation lays the foundation for the future developments of reactor design optimization algorithms.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

An assessment of separable fluid connector system parameters to perform a connector system design optimization study

The key to optimization of design where there are a large number of variables, all of which may not be known precisely, lies in the mathematical tool of dynamic programming developed by Bellman. This methodology can lead to optimized solutions to the design of critical systems in a minimum amount of time, even when there are a great number of acceptable configurations to be considered. To demonstrate the usefulness of dynamic programming, an analytical method is developed for evaluating the relationship among existing numerous connector designs to find the optimum configuration. The data utilized in the study were generated from 900 flanges designed for six subsystems of the S-1B stage of the Saturn 1B space carrier vehicle.

Prasthofer, W. P.↗

Parametric Sensitivity and Calibration for Kain-Fritsch Convective Parameterization Scheme in the WRF Model

Convective parameterizations used in weather and climate models all display sensitivity to model resolution and variable skill in different climatic regimes. Although parameters in convective schemes can be calibrated using observations to reduce model errors, it is not clear if the optimal parameters calibrated based on regional data can robustly improve model skill across different model resolutions and climatic regimes. In this study, this issue is investigated using a regional modeling framework based on the Weather Research and Forecasting (WRF) model. To quantify the response and sensitivity of model performance to model parameters, we identified five key input parameters and specified their ranges in the Kain-Fritsch (KF) convection scheme in WRF and calibrated them across different spatial resolutions, climatic regimes, and radiation schemes using observed precipitation data. Results show that the optimal values for the five input parameters in the KF scheme are close and model sensitivity and error exhibit similar dependence on the input parameters for all experiments conducted in this study despite differences in the precipitation climatology. We found that the model overall performances in simulating precipitation are more sensitive to the coefficients of downdraft (Pd) and entrainment (Pe) mass flux and starting height of downdraft (Ph). However, we found that rainfall biases, which are probably more related to structural errors, still exist over some regions in the simulation even with the optimal parameters, suggesting further studies are needed to identify the sources of uncertainties and reduce the model biases or structural errors associated with missed or misrepresented physical processes and/or potential problems with the modeling framework.

calibration↗

Landsat 9 TIRS-2 Performance Results Based on Subsystem-Level Testing

Landsat 9 is the next in the series of Landsat satellites and has a complement of two pushbroom imagers: Operational Land Imager-2 (OLI-2) that samples the solar reflective spectrum with nine channels and Thermal Infrared Sensor-2 (TIRS-2) samples the thermal infrared spectrum with two channels. The first builds of these sensors, OLI and TIRS, were launched on Landsat 8 in 2013 and Landsat 9 is expected to launch in December 2020. TIRS-2 is designed and built to continue the Landsat data record and satisfy the needs of the remote sensing community. There are two sets of requirements considered for planning the component, subsystem and instrument level tests for TIRS-2: performance requirements and Special Calibration Test Requirements (SCTR). The performance requirements specify key spectral, spatial, radiometric, and operational parameters of TIRS-2 while the SCTRs specify parameters of how the instrument is tested. Several requirements can only be verified at the instrument level, but many performance metrics can be assessed earlier in prelaunch testing at the subsystem level. A test program called TIRS Imaging Performance and Cryoshell Evaluation (TIPCE) was developed to characterize TIRS-2 spectral, spatial, and scattered-light rejection performance at the telescope and detector subsystem level. There were three thermal vacuum campaigns in TIPCE that occurred from November 2017 to March 2018. This work shows results of TIPCE data analysis which provide confidence that key requirements will be met at instrument level with a few minor waivers. A full complement of performance testing will be done at the TIRS-2 instrument level for final verification in late 2018 through Spring 2019.

scatter↗

Triphenylene‐Derived Electron Acceptors and Donors on Ag(111): Formation of Intermolecular Charge‐Transfer Complexes with Common Unoccupied Molecular States

Abstract Over the past years, ultrathin films consisting of electron donating and accepting molecules have attracted increasing attention due to their potential usage in optoelectronic devices. Key parameters for understanding and tuning their performance are intermolecular and molecule–substrate interactions. Here, the formation of a monolayer thick blend of triphenylene‐based organic donor and acceptor molecules from 2,3,6,7,10,11‐hexamethoxytriphenylene (HAT) and 1,4,5,8,9,12‐hexaazatriphenylenehexacarbonitrile (HATCN), respectively, on a silver (111) surface is reported. Scanning tunneling microscopy and spectroscopy, valence and core level photoelectron spectroscopy, as well as low‐energy electron diffraction measurements are used, complemented by density functional theory calculations, to investigate both the electronic and structural properties of the homomolecular as well as the intermixed layers. The donor molecules are weakly interacting with the Ag(111) surface, while the acceptor molecules show a strong interaction with the substrate leading to charge transfer and substantial buckling of the top silver layer and of the adsorbates. Upon mixing acceptor and donor molecules, strong hybridization occurs between the two different molecules leading to the emergence of a common unoccupied molecular orbital located at both the donor and acceptor molecules. The donor acceptor blend studied here is, therefore, a compelling candidate for organic electronics based on self‐assembled charge‐transfer complexes.

Müller, Kathrin↗

Next-generation electronics by co-design with chalcogenide materials

As Moore’s law approaches its limits, chalcogenides offer a promising route to next-generation computing and sensing, thanks to their topological, magnetoelectric, excitonic, and spintronic properties. Yet the same traits that make them appealing, e.g., exotic properties at monolayer thickness, clean van der Waals interfaces, and strong many-body effects, also heighten sensitivity to fabrication, hindering translation into scalable devices. Progress is further constrained by fragmented knowledge across synthesis, processing, and integration, and by the lack of systematic links between fabrication parameters and performance metrics. This Perspective examines key obstacles in controlling chalcogenide heterostructures and stresses the need for an integrated co-design framework, uniting materials growth, processing, and device architecture to accelerate practical technologies.

36 MATERIALS SCIENCE↗

Effusive molecular beam-sampled Knudsen flow reactor coupled to vacuum ultraviolet single photon ionization mass spectrometry using an external free radical source

A new apparatus using vacuum ultraviolet single photon ionization mass spectrometry (VUV SPIMS) of an effusive molecular beam emanating from a Knudsen flow reactor is described. It was designed to study free radical-molecule kinetics over a significant temperature range (300–630 K). Its salient features are: (1) external free radical source, (2) counterpropagating molecular beam and diffuse VUV photon beam meeting in a crossed-beam ion source of a quadrupole mass spectrometer with perpendicular ion extraction, (3) analog detection of the photocurrent of the free radical molecular cation, and (4) possibility of detecting both free radicals and closed shell species in the same apparatus and under identical reaction conditions owing to the presence of photoelectrons generated by the photoelectric effect of the used VUV-photons. The measured thermal molecular beam-to-background ratio was 6.35 ± 0.39 for Ar and 10.86 ± 1.59 for i-C{sub 4}H{sub 10} at 300 K, a factor of 2.52 and 1.50 smaller, respectively, than predicted from basic gas-dynamic considerations. Operating parameters as well as the performance of key elements of the instrument are presented and discussed. Coupled to an external free radical source a steady-state specific exit flow of 1.6 × 10{sup 11} and 5.0 × 10{sup 11} molecule s{sup −1} cm{sup −3} of C{sub 2}H{sub 5}{sup •} (ethyl) and t-C{sub 4}H{sub 9}{sup •} (t-butyl) free radicals have been detected using VUV SPIMS at their molecular ion m/z 29 and 57, respectively, at 300 K.

2-METHYLPROPANE↗