Search NASA⌕ Search

SEARCH · Search NASA

Results for “lightweight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Lightweight sidewalls for aircraft interior noise control

A theoretical and experimental study was performed to devise lightweight sidewalls for turboprop aircraft. Seven concepts for new sidewalls were analyzed and tested for noise reduction using flat panels of 1.2 m x 1.8 m (4 ft x 6 ft), some of which were aircraft-type constructions and some of which were simpler, easier-to-construct panels to test the functioning of an acoustic principle. Aircraft-application sidewalls were then conceived for each of the seven concepts, and were subjectively evaluated for their ability to meet aircraft nonacoustic design requirements. As a result of the above, the following sidewall concepts were recommended for further investigation: a sidewall in which the interior cavity is vented to ceiling and underfloor areas; sidewalls with wall-mounted resonators, one having a conventional trim panel and one a limp one; and a sidewall with a stiff outer wall and a limp trim panel. These sidewalls appear to promise lower weights than conventional sidewalls adjusted to meet similar acoustic requirements, and further development may prove them to be practical.

May, D. N.↗
NASA NTRS1986

An Investigation of Energy Transmission Due to Flexural Wave Propagation in Lightweight, Built-Up Structures

A technique to measure flexural structure-borne noise intensity is investigated. Two accelerometers serve as transducers in this cross-spectral technique. The structure-borne sound power is obtained by two different techniques and compared. In the first method, a contour integral of intensity is performed from the values provided by the two-accelerometer intensity technique. In the second method, input power is calculated directly from the output of force and acceleration transducers. A plate and two beams were the subjects of the sound power comparisons. Excitation for the structures was either band-limited white noise or a deterministic signal similar to a swept sine. The two-accelerometer method was found to be sharply limited by near field and transducer spacing limitations. In addition, for the lightweight structures investigated, it was found that the probe inertia can have a significant influence on the power input to the structure. In addition to the experimental investigation of structure-borne sound energy, an extensive study of the point harmonically forced, point-damped beam boundary value problem was performed to gain insight into measurements of this nature. The intensity formulations were also incorporated into the finite element method. Intensity mappings were obtained analytically via finite element modeling of simple structures.

Mickol, John Douglas↗
NASA NTRS1987

Lightweight piston

A lightweight piston composed of carbon-carbon composites is presented. The use of carbon-carbon composites over conventional materials, such as aluminum, reduces piston weight and improves thermal efficiency of the internal combustion reciprocation engine. Due to the negligible coefficient of thermal expansion and unique strength at elevated temperatures of carbon-carbon, the piston-to-cylinder wall clearance is so small as to eliminate the necessity for piston rings. Use of the carbon-carbon composite has the effect of reducing the weight of other reciprocating engine components allowing the piston to run at higher speeds and improving specific engine performance.

Taylor, Allan H.↗
NASA NTRS1988

Lightweight Video-Camera Head

Compact, lightweight video camera head constructed by remounting lens and charge-coupled-device image detector from small commercial video camera in separate assembly. Useful in robotics, artificial vision, and vision guidance systems. Designed to be mounted on visor of helmet to monitor motions of eyes in experiments on vestibulo-ocular reflexes.

Proctor, David R.↗
NASA NTRS1988

Lightweight Helmet For Eye/Balance Studies

Lightweight helmet serves as mounting platform for stimulus and sensor modules in experiments on role of vestibulo-ocular reflex in motion sickness and space-adaptation syndrome. Fitted liner and five inflatable air bladders stabilize helmet with respect to subject's head. Personal bite board attached to chin-bar assembly makes hard palate in subject's mouth serve as final position reference for helmet.

Mcstravick, M. Catherine↗
NASA NTRS1989

Lightweight Restraint For Coupling Flanges

End flanges of flexible coupling system restrained against excessive rotation or axial separation by inexpensive, lightweight mechanism based on cables and pulleys. Restraining mechanism adapted to cable, duct, hose, or passageway couplings between vehicles, or to other applications in which angular and positional misalignments must be restricted to moderate specified values. Total misalignment of two end flanges limited to amount of slack available in cable-and-pulley mechanism. When cable taut, further axial separation of flange centers restrained, but small tilts accommodated by running of cable through pulleys.

Whitaker, Willie D.↗
NASA NTRS1989

Analysis of the nonvented fill of a 4.96-cubic-meter lightweight liquid hydrogen tank

As part of its development of cryogenic fluid management techniques for spacecraft, the NASA Lewis Research Center Cryogenic Fluid Technology Office (CFTO) is planning to perform ground tests of nonvented fill techniques on a 4.96-cubic-meter lightweight liquid hydrogen tank. This tank is similar in size and shape to the tankage planned for CFTO's COLD-SAT liquid hydrogen flight experiment. The analyses used to select two injection systems are presented for nonvented fills of this tank at design flow rates between 220 and 450 kg/hr. The first system uses multiple nozzles spraying from the top of the tank through the ullage space. This system should be capable of liquid fill levels in excess of 95 percent. The second system injects the liquid through a submerged nozzle and should produce fill levels on the order of 80 percent liquid.

Chato, David J.↗
NASA NTRS1989

Lightweight fibrous nickel electrodes for nickel-hydrogen batteries

The NASA Lewis Research Center is currently developing nickel electrodes for nickel-hydrogen batteries. These electrodes are lighter in weight and have higher energy densities than the heavier state-of-the-art sintered nickel electrodes. Lightweight fibrous materials or plaques are used as conductive supports for the nickel hydroxide active material. These materials are commercial products that are fabricated into nickel electrodes by electrochemically impregnating them with active material. Evaluation is performed in half cells structured in the bipolar configuration. Initial performance tests include capacity measurements at five discharge levels, C/2, 1.0C, 1.37C, 2.0C, and 2.74C. The electrodes that pass the initial tests are life cycle-tested in a low Earth orbit regime at 80 percent depth of discharge.

Britton, Doris L.↗
NASA NTRS1989

Advances in lightweight nickel electrode technology

Studies are currently underway to further the development of lightweight nickel electrode technology. Work is focused primarily on the space nickel-hydrogen system and nickel-iron system but is also applicable to the nickel-cadmium and nickel-zinc systems. The goal is to reduce electrode weight while maintaining or improving performance thereby increasing electrode energy density. Two basic electrode structures are being investigated. The first is the traditional nickel sponge produced from sintered nickel-carbonyl powder and the second is a new material for this application which consists of a non-woven mat of nickel fiber. Electrodes are being manufactured, tested and evaluated at the electrode and cell level.

Coates, Dwaine↗
NASA NTRS1990

Lightweight, Thermally Conductive Composite Material

Aluminum reinforced with carbon fibers superior to copper in some respects. Lightweight composite material has high thermal conductivity. Consists of aluminum matrix containing graphite fibers, all oriented in same direction. Available as sheets, tubes, and bars. Thermal conductivity of composite along fibers rises above that of pure copper over substantial range of temperatures. Graphite/aluminum composite useful in variety of heat-transfer applications in which reduction of weight critical. Used to conduct heat in high-density, high-speed integrated-circuit packages for computers and in base plates for electronic equipment. Also used to carry heat away from leading edges of wings in high-speed airplanes.

Sharp, G. Richard↗
NASA NTRS1990

Small, Lightweight Welding-Current Indicator

Welding-current indicator made of surface-mounted components on flexible circuit board. Holds variety of components on surface. After assembly, flexible circuit wrapped to fit around transformer core. Surface-mounted devices make it unnecessary to drill holes in circuit board to accommodate component leads. Use of small surface-mounted devices result in lightweight, compact indicator circuit.

Huston, Steven W.↗
NASA NTRS1989

Advances in lightweight nickel electrode technology

Studies are currently underway to further the development of lightweight nickel electrode technology. Work is focused primarily on the space nickel-hydrogen system and nickel-iron system but is also applicable to the nickel-cadmium and nickel-zinc systems. The goal is to reduce electrode weight while maintaining or improving performance, thereby increasing electrode energy density. Two basic electrode structures are being investigated. The first is the traditional nickel sponge produced from sintered nickel-carbonyl powder. The second is a new material for this application which consists of a non-woven mat of nickel fiber. Electrodes are being manufactured, tested, and evaluated at the electrode and cell level.

Coates, Dwaine↗
NASA NTRS1990

Lightweight piston architecture

The invention is an improvement in a lightweight carbon-carbon composite piston, the improvement uses near-net shape knitted or warp-interlock preforms to improve the structural qualities of the piston. In its preferred embodiment, a one piece, tubular, closed-ended, knitted preform (a sock) of carbon fibers embedded within the matrix of the piston structure forms the crown, side wall, skirt and inner surface of the piston, and wrap-interlock preforms strengthen the piston crown and wrist pin bosses.

Taylor, Allan H.↗
NASA NTRS1989

Cryogenic optical tests of a lightweight HIP beryllium mirror

Five interferometric tests were conducted at cryogenic temperatures on a lightweight, 50 cm diameter, hot isostatic pressed (HIP) beryllium mirror in the Ames Research Center (ARC) Cryogenic Optics Test Facility. The purpose of the tests was to determine the stability of the mirror's figure when cooled to cryogenic temperatures. Test temperatures ranged from room ambient to 8 K. One cycle to 8 K and five cycles to 80 K were performed. Optical and thermal test methods are described. Data is presented to show the amount of cryogenic distortion and hysteresis present in the mirror when measured with an earlier, Shack interferometer, and with a newly-acquired, phase-measuring interferometer.

Melugin, Ramsey K.↗
NASA NTRS1988

An approach to the design of a simple, radiation hard, highly integrated and reliable, lightweight satellite bus

A spacecraft system concept has been developed which uses ion propulsion and a small, simple, lightweight design approach to carry out a focused lunar science mission. The design relies on existing technology to achieve high reliability and the possibility of a near-term launch. Key characteristics of the mission are highly focused objectives, low launch costs, minimization of development risks and design simplicity. The spacecraft for the lunar mission is described with particular emphasis on the design and reliability approaches used. The degree of adaptability of this basic class of spacecraft bus is discussed with particular emphasis on its application as a technology testbed vehicle. Several potential mission applications are reviewed.

Nock, K. T.↗
NASA NTRS1989

Extremely lightweight space telescope mirrors with integrated active figure control

A concept for an extremely lightweight primary mirror for a large space telescope is proposed. The mirror uses a sandwich structure composed of aluminum faceplates with an aluminum foam core. Modal analysis indicates that a fundamental frequency of 100 Hz can be obtained for a 6 meter diameter mirror with a tapered back and having a total mass of about 3500 kg. An array of thermal actuators embedded in the mirror corrects for figure errors. Such an active thermal figure control system does not have a quick response, but is well suited to space applications where disturbances have relatively long time constants. The advantage of thermal actuators is very high reliability, a primary concern in any space system requiring a large number of actuators.

Bely, Pierre Y.↗
NASA NTRS1991

Thin, Lightweight Solar Cell

Improved design for thin, lightweight solar photovoltaic cells with front contacts reduces degradation of electrical output under exposure to energetic charged particles (protons and electrons). Increases ability of cells to maintain structural integrity under exposure to ultraviolet radiation by eliminating ultraviolet-degradable adhesives used to retain cover glasses. Interdigitated front contacts and front junctions formed on semiconductor substrate. Mating contacts formed on back surface of cover glass. Cover glass and substrate electrostatically bonded together.

Brandhorst, Henry W., Jr.↗