Search NASA⌕ Search

SEARCH · Search NASA

Results for “material response simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Investigation of irradiation damage and heat deposition: a comparative analysis for HEU-to-LEU conversion in HFIR

The planned conversion of the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory from highly enriched uranium (HEU) to low-enriched uranium (LEU) fuel requires detailed evaluation of experiment-relevant parameters to ensure continued performance for materials testing and isotope production. Here, this study presents the first comprehensive assessment of displacements per atom (dpa) and heat deposition rates in target materials within the HFIR flux trap with both HEU and candidate LEU core configurations. Seven analyses were conducted to evaluate key performance metrics, including fast neutron flux distribution, cross section response functions, cross section data, and local dpa and heat deposition rates using mesh- and cell-based tallies. Simulations employed Shift, Monte Carlo N-Particle (MCNP), and the HIFR Controller (HFIRCON) tool suite for high-fidelity transport and depletion modeling. The LEU designs—using U 3 Si 2 -Al dispersion fuel and operating at 95 MW—were compared to the current 85 MW HEU configuration. Results show that while the candidate LEU cores exhibit higher dpa rates due to a harder spectrum and extended cycle lengths, they also demonstrate reduced heat deposition rates in irradiation experiments, primarily due to increased gamma self-shielding from higher 238 U content in the core. These findings confirm that LEU conversion can maintain HFIR’s materials irradiation capabilities but may require redesigning existing experimental hardware.

HEU↗
DOE OSTI2020

(U) Endpoint Energy and Scintillator Geometry Effects on the Swank Factor, Quantum Efficiency, and DQE(0) for High-Energy Radiography

High-energy radiography is used to image imploding materials to better understand weapon design and performance. The Enhanced Capabilities for Subcritical Experiments (ECSE) is a new facility proposal that aims to collect radiographic images of nuclear material. As part of the facility design, we aim to optimize data quality and radiographic performance by investigating different detector designs. We addressed design decisions by simulating different scintillator designs using M CNP6 and calculated the quantum efficiency, Swank factor, and detective quantum efficiency at zero-frequency (DQE(O)). First, we investigated the effects of the x-ray endpoint energy on the detector response. We generated three x-ray spectra with endpoint energies of 20 MeV, 22 MeV, and 24 MeV. The three raw spectra were filtered using the Dual-Axis Radiographic Hydrodynamic Test facility (DARHT) line-of-sight materials along with 1) flat field filtration using 7 cm tungsten alloy in the bullnose and 2) an FTO with 4 plates. The scatter-to-direct radiation ratio was much larger for FTO with 4 plates (50-60%) compared to the flat field with 7 cm of bullnose material (8%). We used these filtered spectra to calculate the detector response for the original DARHT segmented scintillator design. We found that the endpoint energy and filtration had a negligible effect on the detector response. The quantum efficiency was 0.63, the Swank factor was 0.84, and the DQE(O) was 0.53 for all six spectra.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

A REDUCED ORDER MODELING APPROACH TO PROBABILISTIC CREEP-DAMAGE PREDICTIONS IN FINITE ELEMENT ANALYSIS

This paper introduces a computationally efficient Reduced Order Modeling (ROM) approach for the probabilistic prediction of creep-damage failure. Component-level probabilistic simulations are needed to assess the reliability and safety of high-temperature components. Full-scale probabilistic creep-damage modeling in finite element (FE) approach is computationally expensive requiring many hundreds of simulations to replicate the uncertainty of component failure. To that end, ROM is proposed to minimize the elevated computational cost while controlling the loss of accuracy. It is proposed that full-scale probabilistic simulations can be completed in 1D at a reduced cost, the extremum conditions extracted, and those conditions applied for lower-cost 2D/3D probabilistic simulations of components that capture the mean and uncertainty of failure. The probabilistic Sine-hyperbolic (Sinh) model is selected which in previous work was calibrated to alloy 304 stainless steel. The Sinh model includes probability density functions (pdfs) for test condition (stress and temperature), initial damage (i.e. microstructure), and material properties uncertainty. The Sinh model is programmed into ANSYS finite element software using the USERCREEP.F material subroutine. First, the Sinh model and FE code are subject to verification and validation to ensure the accuracy of the simulations. Numerous Monte Carlo simulations are executed in a 1D model to generate probabilistic creep deformation, damage, and rupture data. This data is analyzed and the probabilistic parameters corresponding to extreme creep response are extracted. The ROM concept is applied where only the extreme conditions are applied in the 2D probabilistic prediction of a component. The probabilistic predictions between the 1D and 2D geometry is compared to assess ROM for creep. The accuracy of the probabilistic prediction employing the ROM approach will potentially reduce the time and cost of simulating complex engineering systems. Future studies will introduce multi-stage Sinh, stochasticity, and spatial uncertainty for improved prediction.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The nonexistence of a paddlewheel effect in superionic conductors

Since the 1980s, the paddlewheel effect has been suggested as a mechanism to boost lithium-ion diffusion in inorganic materials via the rotation of rotor-like anion groups. However, it remains unclear whether the paddlewheel effect, defined as large-angle anion group rotations assisting Li hopping, indeed exists; furthermore, the physical mechanism by which the anion-group dynamics affect lithium-ion diffusion has not yet been established. In this work, we differentiate various types of rotational motions of anion groups and develop quaternion-based algorithms to detect, quantify, and relate them to lithium-ion motion in ab initio molecular dynamics simulations. Our analysis demonstrates that, in fact, the paddlewheel effect, where an anion group makes a large angle rotation to assist a lithium-ion hop, does not exist and thus is not responsible for the fast lithium-ion diffusion in superionic conductors, as historically claimed. Instead, we find that materials with topologically isolated anion groups can enhance lithium-ion diffusivity via a more classic nondynamic soft-cradle mechanism, where the anion groups tilt to provide optimal coordination to a lithium ion throughout the hopping process to lower the migration barrier. This anion-group disorder is static in nature, rather than dynamic and can explain most of the experimental observations. Our work substantiates the nonexistence of the long-debated paddlewheel effect and clarifies any correlation that may exist between anion-group rotations and fast ionic diffusion in inorganic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Denoising diffusion algorithm for inverse design of microstructures with fine-tuned nonlinear material properties

Here we introduce a denoising diffusion algorithm to discover microstructures with nonlinear fine-tuned properties. Denoising diffusion probabilistic models are generative models that use diffusion-based dynamics to gradually denoise images and generate realistic synthetic samples. By learning the reverse of a Markov diffusion process, we design an artificial intelligence to efficiently manipulate the topology of microstructures to generate a massive number of prototypes that exhibit constitutive responses sufficiently close to designated nonlinear constitutive behaviors. To identify the subset of microcstructures with sufficiently precise fine-tuned properties, a convolutional neural network surrogate is trained to replace high-fidelity finite element simulations to filter out prototypes outside the admissible range. Results of this study indicate that the denoising diffusion process is capable of creating microstructures of fine-tuned nonlinear material properties within the latent space of the training data. More importantly, this denoising diffusion algorithm can be easily extended to incorporate additional topological and geometric modifications by introducing high-dimensional structures embedded in the latent space. Numerical experiments are conducted on the open-source mechanical MNIST data set (Lejeune, 2020). Consequently, this algorithm is not only capable of performing inverse design of nonlinear effective media, but also learns the nonlinear structure–property map to quantitatively understand the multiscale interplay among the geometry, topology, and their effective macroscopic properties.

42 ENGINEERING↗
DOE OSTI2024

Deformation and Delamination of Dynamically Bulging Bilayered Films

We employ finite element simulations to study the dynamic bulging of films under shock tube conditions and compare these responses with quasi-static bulging. Both scenarios subject the film to time-varying pressure. Two film types are considered: uniform material films and bilayers with a relatively soft interior layer and a hard exterior layer. The interface between the materials in the bilayer cases is modeled as a cohesive zone that follows a bilinear normal traction-separation cohesive law. Additionally, bilayer films with preexisting cracks in the interior layer are analyzed. Parametric studies are also conducted to explore the effects of loading rate and specimen size. The mechanical response of all materials is assumed to be strain-rate independent, focusing solely on the inertial effects in the response of the films under dynamic loading, and the absence of such effects under quasi-static loading. The results indicate that quasi-static bulging exhibits a predictable plate bending like deformation. In contrast, depending on the loading rate and specimen size, dynamic bulging can give rise to elastic waves, and a sequence of deformation processes including initial uniform acceleration, followed by bending-like deformation, and finally through-thickness biaxial stretching. Dynamic loading also leads to larger bulge formation and greater deformation than quasi-static loading. A key finding is the role of preexisting cracks in driving delamination under dynamic loading, which is absent in quasi-static loading. This work enhances our understanding of dynamic bulging and motivates further research on characterizing delamination in layered films using dynamic bulge tests.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Learning to Predict Crystal Plasticity at the Nanoscale: Deep Residual Networks and Size Effects in Uniaxial Compression Discrete Dislocation Simulations

The density and configurational changes of crystal dislocations during plastic deformation influence the mechanical properties of materials. These influences have become clearest in nanoscale experiments, in terms of strength, hardness and work hardening size effects in small volumes. The mechanical characterization of a model crystal may be cast as an inverse problem of deducing the defect population characteristics (density, correlations) in small volumes from the mechanical behavior. In this work, we demonstrate how a deep residual network can be used to deduce the dislocation characteristics of a sample of interest using only its surface strain profiles at small deformations, and then statistically predict the mechanical response of size-affected samples at larger deformations. As a testbed of our approach, we utilize high-throughput discrete dislocation simulations for systems of widths that range from nano- to micro- meters. We show that the proposed deep learning model significantly outperforms a traditional machine learning model, as well as accurately produces statistical predictions of the size effects in samples of various widths. By visualizing the filters in convolutional layers and saliency maps, we find that the proposed model is able to learn the significant features of sample strain profiles.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Liquid Crystal Orientation and Shape Optimization for the Active Response of Liquid Crystal Elastomers

Liquid crystal elastomers (LCEs) are responsive materials that can undergo large reversible deformations upon exposure to external stimuli, such as electrical and thermal fields. Controlling the alignment of their liquid crystals mesogens to achieve desired shape changes unlocks a new design paradigm that is unavailable when using traditional materials. While experimental measurements can provide valuable insights into their behavior, computational analysis is essential to exploit their full potential. Accurate simulation is not, however, the end goal; rather, it is the means to achieve their optimal design. Such design optimization problems are best solved with algorithms that require gradients, i.e., sensitivities, of the cost and constraint functions with respect to the design parameters, to efficiently traverse the design space. In this work, a nonlinear LCE model and adjoint sensitivity analysis are implemented in a scalable and flexible finite element-based open source framework and integrated into a gradient-based design optimization tool. To display the versatility of the computational framework, LCE design problems that optimize both the material, i.e., liquid crystal orientation, and structural shape to reach a target actuated shapes or maximize energy absorption are solved. Multiple parameterizations, customized to address fabrication limitations, are investigated in both 2D and 3D. The case studies are followed by a discussion on the simulation and design optimization hurdles, as well as potential avenues for improving the robustness of similar computational frameworks for applications of interest.

42 ENGINEERING↗
DOE OSTI2022

Simulation of a PCM Integrated Heat Pump Using Time-of-Use Utility Structure based Control Strategy for Demand Response

To mitigate the variation in demand on the electric grid, thermal energy storage (TES) is an alternative to electric batteries and constructing new peaking power plants. The aggressive carbon reduction goals of the United States are accelerating the electrification of building equipment. If space heating and cooling in the US were electrified using conventional heat pump technologies, the winter electric grid peak would approximately double. Integrating TES with heat pump (HP) enables electrification of space cooling and heating devices without overtaxing the grid.This paper evaluates the benefits of a novel phase change material (PCM) integrated heat pump configuration via simulation. A one-dimensional PCM heat exchanger model which discretizes the PCM tank and refrigerant tubes into small control volumes is developed. Each control volume can have different PCM temperatures, PCM properties, and heat transfer coefficients. The PCM tank is charged by a wrapped tank condenser and discharged by an internal refrigerant coil. The PCM heat exchanger model is integrated into DOE/ORNL Heat Pump Design Model for heat pump system simulation.To demonstrate the performance of the PCM integrated heat pump, a case study in Chicago was performed. A Time-of-Use utility structure-based control strategy is implemented to schedule the PCM tank charging and discharging mode switching. Compared with a conventional electric heat pump, the PCM integrated heat pump shows superior performance on load shifting and utility cost reduction. As a result, the proposed system demonstrates 24.6% utility saving for cooling application and 25.8% utility saving for heating application.

Li, Zhenning↗
DOE OSTI2020

Experimental and numerical studies of seismic fluid-structure interaction in a base-supported cylindrical vessel

Seismic design and qualification of advanced reactors will rely heavily on the use of verified and validated numerical models capable of capturing the interaction of the vessel, its contained fluid, and the internal equipment: fluid-structure interaction (FSI) analysis. Analytical solutions can be used for preliminary sizing and design of such vessels but their application is limited to simple geometries and boundary conditions, and small amplitude, translational (and rotational) inputs. To validate numerical models for seismic FSI analysis in finite element codes, a comprehensive set of experiments was performed on a liquid-filled cylindrical vessel, using a 6 degree-of-freedom earthquake simulator. Results in terms of sloshing frequency, damping ratio in sloshing modes, and hydrodynamic responses (wave height, hydrodynamic pressure, base shear, and base moment) for multi-directional earthquake simulator inputs are reported and compared with analytical solutions for liquid-filled vessels. The impact of seismic (base) isolation on hydrodynamic responses was studied using earthquake simulator inputs generated using a virtual isolation system. Data from the experiments are used to validate a numerical model of the fluid-filled vessel using the Arbitrary Lagrangian Eulerian (ALE) solver in the commercial finite element program LS-DYNA. Validation studies are presented for multi-directional seismic inputs, including rocking motions. Lagrangian modeling approaches using an elastic material formulation for the fluid are also investigated and their limitations and possible applications are identified. Here, the results are broadly applicable to the seismic response of base supported, liquid-filled vessels.

58 GEOSCIENCES↗
DOE OSTI2026

Theoretical Study of High Harmonic Generation in Monolayer NbSe 2

High harmonic generation (HHG) is a powerful probe of electron dynamics on attosecond to femtosecond time scales and has been successfully used to detect electronic and structural changes in solid-state quantum materials, including transition-metal dichalcogenides (TMDs). Among TMDs, bulk NbSe 2 exhibits charge density wave (CDW) order below 33 K and becomes superconducting below 7.3 K. Monolayer NbSe 2 also has superconducting and CDW behavior and is therefore interesting as a material whose different structural and electronic properties could be probed via HHG. Here, we predict the HHG response of the pristine 2H and CDW phases of monolayer NbSe 2 using real-time time-dependent density functional theory under the application of a simulated laser pulse excitation. We find that due to the lack of inversion symmetry in both monolayer phases, it is possible to excite even harmonics and that the even harmonics appear as the transverse components of the current response under excitations polarized along the zigzag direction of the monolayer, while odd harmonics arise from the longitudinal current response in all excitation directions. This suggests that the even and odd harmonic responses can be controlled via the polarization of the probing field, opening an avenue for potentially useful applications in optoelectronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An LES study of secondary motion and wall shear stresses in a pipe bend

In this study, large-eddy simulations (LES) of a single-phase, turbulent flow in a 90 ° pipe bend are performed at three Reynolds numbers (5300, 27 000, and 45 000) to investigate the correlation between secondary flow motion and wall shear stresses, which is suspected to be a potential mechanism responsible for material erosion. The isothermal flows are validated against available experimental and numerical data first. The snapshot proper orthogonal decomposition (POD) is applied for the medium and high Reynolds number flows to identify the secondary flow motions and the oscillation of the Dean vortices that are found to cause swirl-switching. Distinguished frequencies of the POD time coefficients at Strouhal numbers of 0.25 and 0.28 are identified for Reynolds numbers at 27 000 and 45 000, respectively. Moreover, shear stress on the pipe wall and the associated power spectral density are obtained and shown to have the same oscillating frequency as the swirl-switching.

42 ENGINEERING↗
DOE OSTI2020

Formation of helices with controllable chirality in gel-fiber composites

While microscale helices with specified chirality are pervasive in biological systems, driving purely synthetic materials to self-organize into such useful structures remains a significant challenge. Through theory and simulations, we model the behavior of initially flat ribbons of gel-fiber composites and show that these materials self-organize into three-dimensional helices with the application of heat. We specifically focus on thermo-responsive gels, which shrink when heated to a point near the lower critical solubility temperature (LCST). Within the composite, regions of the LCST gel that lie far from the fibers can readily shrink in response to the increased temperature; however, near the fibers the network is inhibited from undergoing the heat-induced collapse. This competition between the constrained and the unconstrained regions of the heated sample plays a vital role in the structural evolution of the material. Additionally, we find that this dynamic process can be controlled through the careful placement of the fibers on the outer surface of the gel. We specifically identify fiber arrangements that lead to the formation of helical structures with controlled chirality. Moreover, we isolate scenarios where constraining the movement of one or both the free ends of the sample promotes and stabilizes the formation of helical structures with specified handedness. Such structurally tailored composites are useful for creating mechanically robust actuators, and “appendages” for soft robots that can controllably curl and uncurl with variations in temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Temperature Water Adsorption Isotherms and Ambient Temperature Water Diffusion Rates on Water Harvesting Metal–Organic Frameworks

Water adsorption isotherms from 25 to 125 °C were measured for three metal−organic frameworks (MOFs), MOF-303, MOF-LA2-1, and MIL-100(Fe), which are frequently studied for water harvesting applications. The results show how the step in the water adsorption isotherm varies as a function of temperature and detail the combination of pressure and temperature necessary to remove adsorbed water. Furthermore, isobaric−isothermal Gibbs ensemble Monte Carlo simulations performed for MOF-303 shed light on the change in occupation numbers of the different known water adsorption sites with increasing temperature. Additionally, the diffusion rates of water through these materials were measured using concentration swing frequency response, and micropore diffusion was identified as the controlling mechanism. The Darken relation was used to show the dependence of the diffusion rate on the concentration and the impact of the adsorption isotherm slope. The adsorption of water on MOF-LA2-1 is faster than that on MIL-100(Fe). These data show that MOF-LA2-1 with its high-water adsorption capacity, quick adsorption rate, and favorable desorption energetics is a leading candidate for atmospheric water harvesting.

Adsorption↗
DOE OSTI2023

Mesoscale shock structure in particulate composites

Multiscale experiments in heterogeneous materials and the knowledge of their physics under shock compression are limited. Here, this study examines the multiscale shock response of particulate composites comprised of soda-lime glass particles in a PMMA matrix using full-field high speed digital image correlation (DIC) for the first time. Normal plate impact experiments, and complementary numerical simulations, are conducted at stresses ranging from 1.1 - 3.1 GPa to elucidate the mesoscale mechanisms responsible for the distinct shock structure observed in particulate composites. The particle velocity from the macroscopic measurement at continuum scale shows a relatively smooth velocity profile, with shock thickness decreasing with an increase in shock stress, and the composite exhibits strain rate scaling as the second power of the shock stress. In contrast, the mesoscopic response was highly heterogeneous, which led to a rough shock front and the formation of a train of weak shocks traveling at different velocities. Additionally, the normal shock was seen to diffuse the momentum in the transverse direction, affecting the shock rise and the rounding-off observed at the continuum scale measurements. The numerical simulations indicate that the reflections at the interfaces, wave scattering, and interference of these reflected waves are the primary mechanisms for the observed rough shock fronts.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of the Fusion Zone in Laser Beam Welds on SS304L

Designing a welded joint requires consideration of the welding process, component/assembly structure and weld geometry, material composition, properties, and desired joint performance. The designer must also specify a set of acceptance criteria used to evaluate the welds. This study was conducted to support the design team responsible for specifying the spot weld profile by investigating the relationship between weld process parameters and the weld geometry and properties to further inform design optimization. The subjects of this study are two thin stainless steel 304L (SS304L) components joined by Laser Beam Welding (LBW). The components are the Housing, which contains flexible circuitry, and the Cover that protects the circuitry during handling, installation, and under service loads. Figure 1 illustrates coupon versions of the Cover and Housing used to simulate the interface between these components for weld testing. These coupon representations of assembly components were designed to match the material and relevant geometry related to the welded joint while other features not relevant to the welded joint are excluded.The objective of this study was to characterize the sensitivity of the weld geometry and mechanical properties to the input weld parameters to inform further Finite Element Analysis (FEA) efforts in balancing joint strength against assembly deformation caused by the welding process. Characterization was accomplished by varying laser welding parameters around the current design values and measuring weld geometry on the cross-sections. Nanoindentation with a spherical and flat-ended tip was used on polished section cuts of the weld to obtain direct estimates of the stress-strain response of the Fusion Zone (FZ) for comparison to the Base Metal (BM).

42 ENGINEERING↗
DOE OSTI2024

ForceGen: End-to-end de novo protein generation based on nonlinear mechanical unfolding responses using a language diffusion model

Through evolution, nature has presented a set of remarkable protein materials, including elastins, silks, keratins and collagens with superior mechanical performances that play crucial roles in mechanobiology. However, going beyond natural designs to discover proteins that meet specified mechanical properties remains challenging. Here, we report a generative model that predicts protein designs to meet complex nonlinear mechanical property-design objectives. Our model leverages deep knowledge on protein sequences from a pretrained protein language model and maps mechanical unfolding responses to create proteins. Via full-atom molecular simulations for direct validation, we demonstrate that the designed proteins are de novo, and fulfill the targeted mechanical properties, including unfolding energy and mechanical strength, as well as the detailed unfolding force-separation curves. Our model offers rapid pathways to explore the enormous mechanobiological protein sequence space unconstrained by biological synthesis, using mechanical features as the target to enable the discovery of protein materials with superior mechanical properties.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Fluorophilic Sigma(σ)‐Lock Self‐Healable Copolymers

Although F-Containing molecules and macromolecules are often used in molecular biology to increase the binding with Lewis acidic groups by introducing favorable C−F dipoles, there is virtually no experimental evidence and limited understanding of the nature of these interactions, especially their role in synthetic polymeric materials. These studies elucidate the molecular origin of inter- and intra-Chain interactions responsible for self-healing of F-Containing copolymers composed of pentafluorostyrene and n-butyl acrylate units (p(PFS/nBA). Guided by dynamic surface oscillating force (SOF) and spectroscopic measurements supported by molecular dynamics (MD) simulations, these studies show that the reformation of σ-σ orbitals in −C−F of PFS and CH 3 CH 2 − of nBA units enables the recovery of entropic energy via fluorophilic-σ-lock van der Waals forces when PFS/nBA molar ratios are ~50/50. The strength of these interactions determined experimentally for self-healable PFS/nBA compositions is in the order ~0.3 kcal/mol which primarily comes from fluorophilic-σ-lock (~70 %) contributions. These interactions are significantly diminished for non-self-healable counterparts. Strongly polarized −C−F σ orbitals create lateral dipolar forces enhancing the affinity towards −C−H orbitals, facilitating energetically favorable interactions. Entropic recovery driven by non-Covalent bonding offers a valuable tool in designing materials with unique functionalities, particularly self-healable batteries and energy storage devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗