Search NASA⌕ Search

SEARCH · Search NASA

Results for “missing values”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

A comparison of deep-learning-based inpainting techniques for experimental X-ray scattering

The implementation is proposed of image inpainting techniques for the reconstruction of gaps in experimental X-ray scattering data. The proposed methods use deep learning neural network architectures, such as convolutional autoencoders, tunable U-Nets, partial convolution neural networks and mixed-scale dense networks, to reconstruct the missing information in experimental scattering images. In particular, the recovered pixel intensities are evaluated against their corresponding ground-truth values using the mean absolute error and the correlation coefficient metrics. The results demonstrate that the proposed methods achieve better performance than traditional inpainting algorithms such as biharmonic functions. Overall, tunable U-Net and mixed-scale dense network architectures achieved the best reconstruction performance among all the tested algorithms, with correlation coefficient scores greater than 0.9980.

97 MATHEMATICS AND COMPUTING↗

KCMP Minnesota Tall Tower Ammonia Observations and Emission Estimates Dataset 2017-2018

This data set contains NH3 mixing ratios, net ecosystem NH3 exchange, and supporting information measured at a tall tower (KCMP, 244 meter) site near St. Paul, Minnesota, USA. The data include NH3 and H2O mixing ratios measured at the 100 meter level, as well as NH3 mixing ratio measured at the 56 meter level. Wind data was measured using a sonic anemometer at the 185 meter level. Also included in this data set are values of wet N and NH3 deposition from 2016 - 2018. This data was collected to improve understanding of the ammonia and reactive nitrogen budget for the region.Ammonia mixing ratios were filtered for periods when the NH3 analyzer measured anomalous (i.e. 10 mmol mol-1) water vapor mixing ratios based on comparison with the IRGA (LI7000). Further, we filtered out NH3 observations obtained during strongly condensing conditions. These periods were identified when the water vapor mixing ratio differences between the 100 m and 56 m levels were more negative than -0.5 mmol mol-1 (i.e. when the water vapor gradient was strong and directed toward the land surface). Finally, we filtered out NH3 fluxes when the atmosphere was strongly stable (i.e. when (z-d)/L exceeded a value of +4.5) and subject to decoupling from the surface fluxes. Approximately 35.1% of the hourly flux data were either missing due to instrument failure or filtered according to the above quality control procedures.

54 ENVIRONMENTAL SCIENCES↗

$\sqrt{\hat{s}}_{min}$ : A Global inclusive variable for determining the mass scale of new physics in events with missing energy at hadron colliders

We propose a new global and fully inclusive variable \sqrt{s}_{min} for determining the mass scale of new particles in events with missing energy at hadron colliders. We define \sqrt{s}_{min} as the minimum center-of-mass parton level energy consistent with the measured values of the total calorimeter energy E and the total visible momentum \vec{P}. We prove that for an arbitrary event, \sqrt{s}_{min} is simply given by the formula \sqrt{s}_{min}=\sqrt{E^2-P_z^2}+\sqrt{\met^2+M_{inv}^2}, where M_{inv} is the total mass of all invisible particles produced in the event. We use t\bar{t} production and several supersymmetry examples to argue that the peak in the \sqrt{s}_{min} distribution is correlated with the mass threshold of the parent particles originally produced in the event. This conjecture allows a determination of the heavy superpartner mass scale (as a function of the LSP mass) in a completely general and model-independent way, and without the need for any exclusive event reconstruction. In our SUSY examples of several multijet plus missing energy signals, the accuracy of the mass measurement based on \sqrt{s}_{min} is typically at the percent level, and never worse than 10%.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Quantum Chemical Approach for Calculating Stability Constants of Mercury Complexes

Stability constants are central to the multi-scale modeling of the thermodynamic speciation, cycling, and transport of mercury (Hg) and other contaminants in aquatic environments. However, for Hg, experimental values for many relevant complexes are not available, and for others can span ranges in excess of 10 log units. The missing data and large uncertainties mean there are significant knowledge gaps in predictions of thermodynamic speciation. As an alternative to experimental measurements, thermodynamic quantities can be calculated with quantum chemical methods. Among these, density functional theory (DFT) with a polarizable continuum solvent combines accuracy with practicability. In this paper, we present an accurate and quick approach in which we use DFT with continuum solvation to calculate stability constants of Hg complexes with inorganic and low molecular-weight organic ligands in aqueous solution. Specifically, we use the M06/[SDD]6-31+G(d,p) level of theory in combination with a modified version of the SMD solvent model in which the solute radii are re-optimized with a scaled solvent-accessible surface (sSAS) approach. For the set of 37 Hg complexes used for optimization, which contain environmentally relevant functional groups and have reliable experimental stability constants, we obtain a mean unsigned error of 1.4 log units. Testing the method on an independent set of 12 Hg complexes reproduces the experimental stability constants to a mean unsigned error of 1.6 log units. Finally, this approach is a substantial step toward generally applicable rapid stability constant derivation for a wide range of Hg complexes, including those present in dissolved organic matter.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Missing energy and the measurement of the CP-violating phase in neutrino oscillations

In the next generation of long-baseline neutrino oscillation experiments aiming to determine the charge-parity-violating phase δ CP in the appearance channel, fine-grained time-projection chambers are expected to play an important role. In this study, we analyze an influence of realistic detector capabilities on the δ CP sensitivity for a setup similar to that of the Deep Underground Neutrino Experiment. We find that the effect of the missing energy carried out by undetected particles is sizable. Although the reconstructed neutrino energy can be corrected for the missing energy, the accuracy of such procedure has to exceed 20%, to avoid a sizable bias in the extracted δ CP value.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Suitability of markerless EPID tracking for tumor position verification in gated radiotherapy

Purpose: To maximize the benefits of respiratory gated radiotherapy (RGRT) of lung tumors real-time verification of the tumor position is required. This work investigates the feasibility of markerless tracking of lung tumors during beam-on time in electronic portal imaging device (EPID) images of the MV therapeutic beam. Methods: EPID movies were acquired at ∼2 fps for seven lung cancer patients with tumor peak-to-peak motion ranges between 7.8 and 17.9 mm (mean: 13.7 mm) undergoing stereotactic body radiotherapy. The external breathing motion of the abdomen was synchronously measured. Both datasets were retrospectively analyzed inPortalTrack, an in-house developed tracking software. The authors define a three-step procedure to run the simulations: (1) gating window definition, (2) gated-beam delivery simulation, and (3) tumor tracking. First, an amplitude threshold level was set on the external signal, defining the onset of beam-on/-off signals. This information was then mapped onto a sequence of EPID images to generate stamps of beam-on/-hold periods throughout the EPID movies in PortalTrack, by obscuring the frames corresponding to beam-off times. Last, tumor motion in the superior-inferior direction was determined on portal images by the tracking algorithm during beam-on time. The residual motion inside the gating window as well as target coverage (TC) and the marginal target displacement (MTD) were used as measures to quantify tumor position variability. Results: Tumor position monitoring and estimation from beam's-eye-view images during RGRT was possible in 67% of the analyzed beams. For a reference gating window of 5 mm, deviations ranging from 2% to 86% (35% on average) were recorded between the reference and measured residual motion. TC (range: 62%–93%; mean: 77%) losses were correlated with false positives incidence rates resulting mostly from intra-/inter-beam baseline drifts, as well as sudden cycle-to-cycle fluctuations in exhale positions. Both phenomena can lead to considerable deviations (with MTD values up to a maximum of 7.8 mm) from the intended tumor position, and in turn may result in a marginal miss. The difference between tumor traces determined within the gating window against ground truth trajectory maps was 1.1 ± 0.7 mm on average (range: 0.4–2.3 mm). Conclusions: In this retrospective analysis of motion data, it is demonstrated that the system is capable of determining tumor positions in the plane perpendicular to the beam direction without the aid of fiducial markers, and may hence be suitable as an online verification tool in RGRT. It may be possible to use the tracking information to enable on-the-fly corrections to intra-/inter-beam variations by adapting the gating window by means of a robotic couch.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Aircraft Anomaly Detection Using Performance Models Trained on Fleet Data

This paper describes an application of data mining technology called Distributed Fleet Monitoring (DFM) to Flight Operational Quality Assurance (FOQA) data collected from a fleet of commercial aircraft. DFM transforms the data into aircraft performance models, flight-to-flight trends, and individual flight anomalies by fitting a multi-level regression model to the data. The model represents aircraft flight performance and takes into account fixed effects: flight-to-flight and vehicle-to-vehicle variability. The regression parameters include aerodynamic coefficients and other aircraft performance parameters that are usually identified by aircraft manufacturers in flight tests. Using DFM, the multi-terabyte FOQA data set with half-million flights was processed in a few hours. The anomalies found include wrong values of competed variables, (e.g., aircraft weight), sensor failures and baises, failures, biases, and trends in flight actuators. These anomalies were missed by the existing airline monitoring of FOQA data exceedances.

Gorinevsky, Dimitry↗

Environment Modeling Using Runtime Values for JPF-Android

Software applications are developed to be executed in a specific environment. This environment includes external native libraries to add functionality to the application and drivers to fire the application execution. For testing and verification, the environment of an application is simplified abstracted using models or stubs. Empty stubs, returning default values, are simple to generate automatically, but they do not perform well when the application expects specific return values. Symbolic execution is used to find input parameters for drivers and return values for library stubs, but it struggles to detect the values of complex objects. In this work-in-progress paper, we explore an approach to generate drivers and stubs based on values collected during runtime instead of using default values. Entry-points and methods that need to be modeled are instrumented to log their parameters and return values. The instrumented applications are then executed using a driver and instrumented libraries. The values collected during runtime are used to generate driver and stub values on- the-fly that improve coverage during verification by enabling the execution of code that previously crashed or was missed. We are implementing this approach to improve the environment model of JPF-Android, our model checking and analysis tool for Android applications.

Verification↗

Resolution Versus Error for Computational Electron Microscopy

Images that are collected via scanning transmission electron microscopy (STEM) can be undersampled to avoid damage to the specimen while maintaining resolution [1, 2]. We have used BPFA to impute missing data and reduce noise [3]. The reconstruction is typically evaluated using the peak signal-to-noise ratio (PSNR). This measure is too conservative for STEM images and we propose that the Fourier ring correlation (FRC) is used instead to evaluate the reconstruction. We are not concerned with exact reconstruction of the truth image, and therefore PSNR is a conservative estimation of the quality of the reconstruction. Instead, we are concerned with the visual resolution of the image and whether atoms can be distinguished. We have evaluated the reconstruction of a simulated STEM image using the FRC and compared the results with the PSNR measurements. The FRC captures the resolution of the image and is not affected by a large MSE if the atom peaks are still distinguishable. The noisy and reconstructed images are shown in Figure 1. The simulated STEM image was sampled at 100%, 80%, 40%, and 20% of the original pixels to simulate an undersampled scan. The reconstruction was done using BPFA with a patch size of 10 x 10 and no overlapping patches. Not having overlapping patches produces inferior results but they are still acceptable. The dictionary size is 64 and 30 iterations were completed during each reconstruction. The 100% image was denoised instead of reconstructed. Poisson noise was applied to the simulated image with λ values of 500, 50, and 5 to simulate lower imaging dose. The original simulated STEM image was also included in our calculations and was generated using a dose of 1000. The simulated STEM image is 100 by 100 pixels and has essentially no high frequency components. The image reconstruction tends to smooth the data, also resulting in no high frequency components. This causes the FRC of the two images to be large at higher resolutions and may be misleading. For this reason, the BPFA has no overlap to avoid excessive smoothing. Moreover, the resolution of the simulated image is approximately 9.2 (1/nm), so we only look that far in the frequency domain when performing FRC. If the FRC curve does not crossover the threshold, a resolution value of 9.2 is used. We emphasize that our reported results are conservative. The FRC and PSNR values using the ground truth and the reconstructed images are shown in Tables 1 and 2. The left side show the metrics without using BPFA (missing pixels) and the right side show the metrics after using BPFA. When we did not use BPFA, the Fourier transform was estimated [4]. Some threshold curves have been studied [5], but they are derived for additive noise models. Since we have a Poisson noise model, we have used the more conservative threshold of 0.5 for our calculations. Ten images were used to construct each cell of tables in the form of the mean of the metric plus or minus its standard deviation. As expected, the PSNR dies off much quicker than the FRC values for the same image. For the 100% and 80% sampled versions of the truth image, the resolution only dies off when the dose is 5. However, the PSNR dies off rapidly as the dose is reduced. For the 1000, 500, and 50 dose images, the FRC is the maximum, or close, until we undersample at 20%. The PSNR for these values tapers down as we get into the bottom right hand corner of the table, even though the resolution remains high. Overall, we find that undersampled images can be reconstructed to acceptable resolution even when the dose per pixel is also reduced[6]. References: [1]A Stevens, H Yang, L Carin et al. Microscopy 63(1), (2014), pp. 41. [2]A Stevens, L Kovarik, P Abellan et al. Advanced Structural and Chemical Imaging 1(1), (2015), pp. 1. [3]M Zhou, H Chen, J Paisley et al. Image Processing, IEEE Transactions on 21(1), (2012), pp. 130. [4]V. Y. Liepin’sh. Automatic control and computer sciences 30(3), (1996), pp. 20.

Luzi, Lorenzo↗

Observation of Single Top-Quark Production

We report observation of the electroweak production of single top quarks in pp collisions at sq root(s)=1.96 TeV based on 2.3 fb{sup -1} of data collected by the D0 detector at the Fermilab Tevatron Collider. Using events containing an isolated electron or muon and missing transverse energy, together with jets originating from the fragmentation of b quarks, we measure a cross section of sigma(pp->tb+X,tqb+X)=3.94+-0.88 pb. The probability to measure a cross section at this value or higher in the absence of signal is 2.5x10{sup -7}, corresponding to a 5.0 standard deviation significance for the observation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

M{sub T2}-assisted on-shell reconstruction of missing momenta and its application to spin measurement at the LHC

We propose a scheme to assign a 4-momentum to each WIMP in new physics event producing a pair of mother particles each of which decays to an invisible weakly interacting massive particle (WIMP) plus some visible particle(s). The transverse components are given by the value that determines the event variable M{sub T2}, while the longitudinal component is determined by the on-shell condition on the mother particle. Although it does not give the true WIMP momentum in general, this M{sub T2}-assisted on-shell reconstruction of missing momenta provides kinematic variables well correlated to the true WIMP momentum and thus can be useful for an experimental determination of new particle properties. We apply this scheme to some processes to measure the mother particle spin and find that spin determination is possible even without good knowledge of the new particle masses.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Triplet scalars and dark matter at the LHC

We investigate the predictions of a simple extension of the standard model where the Higgs sector is composed of one SU(2){sub L} doublet and one real triplet. We discuss the general features of the model, including its vacuum structure, theoretical and phenomenological constraints, and expectations for Higgs collider studies. The model predicts the existence of a pair of light charged scalars and, for vanishing triplet vacuum expectation value, contains a cold dark matter candidate. When the latter possibility occurs, the charged scalars are long-lived, leading to a prediction of distinctive single charged track with missing transverse energy or double charged track events at the large hadron collider. The model predicts a significant excess of two-photon events compared to SM expectations due to the presence of a light charged scalar.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Derivation of Mathematical Expressions to Define Resonant Ejection from Square and Sinusoidal Wave Ion Traps

The use of resonant ejection for mass analysis with ion traps is increasing primarily because it markedly improves the mass range and resolution of ion traps. Unfortunately, an easy-to-use analytical expression that defines the ejection mass as a function of the trapping and excitation frequencies is missing in the literature because the secular frequency of the ions in sinusoidal ion traps is not easily determined for all stable values of qz from the Mathieu equation. However, the ion secular frequency for all stable values of qz in digital ion traps can be readily determined from Hill s equation. We have taken this expression and solved it for qz to produce an analytical expression for the ejection mass as a function of trapping and excitation frequency. We also recognized that the expression for the ion mass during resonant ejection for a square wave driven trap can be converted to an expression for a sinusoidal wave trap merely by multiplication by a factor of 4/ . These new expressions open up the possibility of rapid mass calibration for any method of resonant ejection from square or sinusoidal wave driven ion traps.

97 MATHEMATICS AND COMPUTING↗

Edge charge asymmetry in top pair production at the LHC

In this brief report, we propose a new definition of charge asymmetry in top pair production at the LHC, namely, the edge charge asymmetry (ECA). ECA utilizes the information of drifting direction only for single top (or antitop) with hadronic decay. Therefore, ECA can be free from the uncertainty arising from the missing neutrino in the tt event reconstruction. Moreover, rapidity Y of top (or antitop) is required to be greater than a critical value Y{sub C} in order to suppress the symmetric tt events mainly due to the gluon-gluon fusion process. In this paper, ECA is calculated up to next-to-leading order QCD in the standard model and the choice of the optimal Y{sub C} is investigated.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Detection of Disruptions in the High-β Spherical Torus NSTX

This paper describes the prediction of disruptions based on diagnostic data in the high-β spherical torus NSTX. The disruptive threshold values on many signals are examined. In some cases, raw diagnostic data can be used as a signal for disruption prediction. In others, the deviations of the plasma data from simple models provides the signal used to determine the proximity to disruption. However, no single signal and threshold value can form the basis for disruption prediction in NSTX; thresholds that produce an acceptable false positive rate have too large a missed or late warning rate, while combinations that produce an acceptable rate of missed or late warnings have an unacceptable false positive rate. To solve this problem, a novel means of combining multiple threshold tests has been developed. After being properly tuned, this algorithm can produce a false positive rate of 2.8%, with a late warning rate of 3.7% when applied to a database of ~2000 disruptions collected from three run campaigns. Furthermore, many of these false positives are triggered by near-disruptive MHD events that might indeed be disruptive in larger plasmas with more stored energy. However, the algorithm is less efficient at detecting the MHD event that prompts the disruption process.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Dose Rate Conversion Factors for Nuclear Fallout

In a previous paper, the composite exposure rate conversion factor (ECF) for nuclear fallout was calculated using a simple theoretical photon-transport model. The theoretical model was used to fill in the gaps in the FGR-12 table generated by ORNL. The FGR-12 table contains the individual conversion factors for approximate 1000 radionuclides. However, in order to calculate the exposure rate during the first 30 minutes following a nuclear detonation, the conversion factors for approximately 2000 radionuclides are needed. From a human-effects standpoint, it is also necessary to have the dose rate conversion factors (DCFs) for all 2000 radionuclides. The DCFs are used to predict the whole-body dose rates that would occur if a human were standing in a radiation field of known exposure rate. As calculated by ORNL, the whole-body dose rate (rem/hr) is approximately 70% of the exposure rate (R/hr) at one meter above the surface. Hence, the individual DCFs could be estimated by multiplying the individual ECFs by 0.7. Although this is a handy rule-of-thumb, a more consistent (and perhaps, more accurate) method of estimating the individual DCFs for the missing radionuclides in the FGR-12 table is to use the linear relationship between DCF and total gamma energy released per decay. This relationship is shown in Figure 1. The DCFs for individual organs in the body can also be estimated from the estimated whole-body DCF. Using the DCFs given FGR-12, the ratio of the organ-specific DCFs to the whole-body DCF were plotted as a function of the whole-body DCF. From these plots, the asymptotic ratios were obtained (see Table 1). Using these asymptotic ratios, the organ-specific DCFs can be estimated using the estimated whole-body DCF for each of the missing radionuclides in the FGR-12 table. Although this procedure for estimating the organ-specific DCFs may over-estimate the value for some low gamma-energy emitters, having a finite value for the organ-specific DCFs in the table is probably better than having no value at all. A summary of the complete ECF and DCF values are given in Table 2.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Crossing the Eddington Limit: Examining Disk Spectra at High Accretion Rates

The faintest ultraluminous X-ray sources (ULXs), those with 0.3–10 keV luminosities 1<L{sub X}/10{sup 39}<3 erg s{sup −1}, tend to have X-ray spectra that are disk-like but broader than expected for thin accretion disks. These “broadened disk (BD)” spectra are thought to indicate near- or mildly super-Eddington accretion onto stellar remnant black holes. Here we report that a sample of bright thermal-dominant black hole binaries, which have Eddington ratios constrained to moderate values, also show BD spectra in the 0.3–10 keV band at an order of magnitude lower luminosities. This broadening would be missed in studies that only look above ∼2 keV. While this may suggest that BD ULXs could be powered by accretion onto massive stellar remnant black holes with close to maximal spin, we argue in favor of a scenario where they are at close to the Eddington luminosity, such that radiation pressure would be expected to result in geometrically slim, advective accretion disks. However, this implies that an additional physical mechanism is required to produce the observed broad spectra at low Eddington ratios.

79 ASTRONOMY AND ASTROPHYSICS↗

Aerosol and Cloud Experiments in the Eastern North Atlantic (ACE-ENA) Winter Intensive Operational Period: Aerodynamic Particle Sizer Field Campaign Report

An aerodynamic particle sizer spectrometer (APS, model 3321 by TSI Inc., Shoreview, Minnesota) was deployed at the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facility Eastern North Atlantic (ENA) observatory during the second (winter) intensive operational period (IOP) of the Aerosol and Cloud Experiments in the Eastern North Atlantic (ACE-ENA) field campaign. Data were collected from January 9 through February 26, 2018, covering the second deployment of the ARM Aerial Facility (AAF) aircraft within ACE-ENA. The standard ENA instrument suite does not provide measurements of aerosol particle size distribution for diameters greater than one micron. Properties of coarse-mode (super-micron) aerosols are rarely measured, although super-micron particles can play an important role in the aerosol life cycle, affecting aerosol optical properties and cloud nuclei activity (e.g., Clarke et al. 2003). The APS was deployed to fill this gap in particle size measurements: it is capable of measuring size-resolved concentration of the aerosols in the 0.5-20 μm range (aerodynamic diameter). The APS was installed in the aerosol trailer to sample through the main stack. Special attention was given to selection of the instrument location (just below the main stack) to minimize particle losses in the connecting lines. Most atmospheric aerosols are hygroscopic, so the measurement of the aerosol size distributions should either be performed in a controlled humidity environment or accompanied by concurrent measurement of the temperature and humidity of the sample air. The latter strategy was used during this deployment: a high-precision humidity/temperature transmitter (model EE08 by E+E Elektonik GMBH, Engerwitzdorf, Germany) was mounted in the APS sampling line immediately upstream of the APS inlet. A dedicated laptop computer was used for data collection and communications. The APS was controlled with vendor-supplied software (Aerosol Instrument Manager, ver. 10.1, TSI); aerosol size distribution data were collected over a period of 55 seconds and converted to one-minute averages. Temperature and humidity analog signals were acquired via analog-to-digital converter (ADC) module (model WTAIN-M by Weeder Technologies, Fort Walton Beach, Florida) using vendor-supplied software (ModCom) with 1- sec resolution. In post-processing, the APS data were exported from TSI proprietary format into “comma-separated value” American Standard Code for Information Interchange (ASCII) files and matched with appropriately averaged temperature and humidity data. Two significant periods of missing data were caused by local power outages. Vendor-supplied software was not designed for unattended operation: it needs to be manually restarted including sensor configuration setup.

ACE-ENA, Azores, ultra-high-sensitivity aerosol sp↗