SEARCH · Search NASA

Results for “outgassing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Effect of the space environment on materials flown on the EURECA/TICCE-HVI experiment

The primary benefit of accurately quantifying and characterizing the space environmental effects on materials is longer instrument and spacecraft life. Knowledge of the limits of materials allows the designer to optimize the spacecraft design so that the required life is achieved. Materials such as radiator coatings that have excellent durability result in the design of smaller radiators than a radiator coated with a lower durability coating. This may reduce the weight of the spacecraft due to a more optimum design. Another benefit of characterizing materials is the quantification of outgassing properties. Spacecraft which have ultraviolet or visible sensor payloads are susceptible to contamination by outgassed volatile materials. Materials with known outgassing characteristics can be restricted in these spacecraft. Finally, good data on material characteristics improves the ability of analytical models to predict material performance. A flight experiment was conducted on the European Space Agency's European Retrievable Carrier (EuReCa) as part of the Timeband Capture Cell Experiment (TICCE). Our main objective was to gather additional data on the dust and debris environments, with the focus on understanding growth as a function of size (mass) for hypervelocity particles 1E-06 cm and larger. In addition to enumerating particle impacts, hypervelocity particles were to be captured and returned intact. Measurements were performed post-flight to determine the flux density, diameters, and subsequent effects on various optical, thermal control and structural materials. In addition to these principal measurements, the experiment also provided a structure and sample holders for the exposure of passive material samples to the space environment, e.g., the effects of thermal cycling, atomic oxygen, etc. Preliminary results are presented, including the techniques used for intact capture of particles.

Maag, Carl R.↗

NASA NTRS1994

IR excitation of contaminant water by oxygen for the space shuttle at low Earth orbit altitude

As the water outgas of a space shuttle passes through the rarefied atmosphere at orbital altitude, collisions occur between the gases with sufficient energy to excite infrared-active water molecules to various vibrational and rotational states. An infrared contaminant model (IR model) has been developed to study the shuttle-induced excitation and emission of water molecules outgassed from the space shuttle. The focus of the first application of the model is translation-to-vibration (T-V) energy transfer since estimates suggest that this process should dominate the production of vibrationally excited H2O under typical low Earth orbit conditions. Using the velocity and position distribution functions of interacting neutral gases obtained from a neutral gases interaction model, the spatial distributions of excitation and IR radiation from contaminant water are computed, and typical results are presented. Infrared spectral data (450 - 2500/cm), measured by the Cryogenic Infrared Radiance Instrumentation for Shuttle (CIRRIS-1A) sensor on STS-39 (April 28 to May 6, 1991) at an altitude near 265 km, are used to test model predictions. The dependence of the radiant emission structure and brightness on outgassing rates and altitudes is discussed. The time history of the contaminant water outgassing rate is inferred for STS-39, and it is compared with the mass-spectrometer-based results for STS-4 (June 26 to July 4, 1982). Also, estimates of H2O column density at mission elapsed time (MET) 50 hours are compared for missions STS-2, STS-3, STS-4, and STS-39.

Zhou, D. K.↗

NASA NTRS1994

Evolution of the martian atmosphere

Carbon dioxide, nitrogen, and the nonradiogenic and radiogenic noble gases are tracked from primordial inventories to their present states in a revised model of atmospheric evolution on Mars. Elemental and isotopic abundances evolve by hydrodynamic escape, impact erosion, outgassing, sputtering, photochemical escape of nitrogen, and carbonate formation and recycling. Atmospheric history is divided into early and late evolutionary periods, the first characterized by high CO2 pressures and a possible greenhouse and the second by a low pressure cap-regolith buffered system initiated by polar CO2 condensation approximately 3.7 Gyr ago. During early evolution the Xe isotopes are fractionated to their present composition by hydraulic escape, and CO2 pressure and isotopic history are dictated by the interplay of losses to erosion, sputtering, and carbonate precipitation, additions by outgassing and carbonate recycling, and perhaps also by feedback stabilization under greenhouse conditions. Atmospheric collapse near 3.7 Gyr leads to abrupt increases in the mixing ratios of preexisting Ar, Ne, and N2 at the exobase and their rapid removal by sputtering. Current abundances and isotopic compositions of these light species are therefore entirely determined by the action of sputtering and photochemical escape on gases supplied by outgassing during the late evolutionary epoch. The present atmospheric Kr inventory also derives almost completely from solar-like Kr degassed during this period. Consequently, among current observables, only the Xe isotopes and delta(C-13) survive as isotopic tracers of atmospheric history prior to its transition to low pressure.

Pepin, Robert O.↗

NASA NTRS1996

Hygrothermal properties of composites

The testing procedure and acceptance criteria for outgassing selection of materials to be used in spacecraft has been reviewed. Outgassing testing should be conducted according to ASTM Standard E 595-90. In general, materials with CVCM less than or equal to 0.10% and TML less than or equal to 1.00% are acceptable for space applications. Next, test data on several types of graphite-epoxy composite materials are presented over time at various relative humidity levels at room temperature for moisture absorption, and under vacuum at several temperatures for moisture desorption (outgassing). The data can be accurately represented by simple equations which are useful for materials characterization. Finally, a laser dilatometer systems of extremely high sensitivity and accuracy was assembled and used to measure the coefficient of thermal expansion (CTE) of several types of graphite-epoxy structures, culminating in the ability to perform loading and thermal expansion tests on a prototype optical bench.

Arsenovic, Petar↗

NASA NTRS1997

Reduction of Calcofluor in Solithane Conformal Coatings of Printed Wiring Boards

An investigation on the outgassing of a pigment employed as a fluorescent medium in conformal coatings has been performed. The conformal coatings in question are used to protect printed wiring boards from environmental hazards such as dust and moisture. The pigment is included in the coating at low concentration to allow visual inspection of the conformal coating for flaw detection. Calcofluor, the fluorescent pigment has been found to be a significant outgasser under vacuum conditions and a potential source of contamination to flight hardware. A minimum acceptable concentration of Calcofluor for flaw detection is desirable. Tests have been carried out using a series of Solithane(TM) conformal coating samples, with progressively lower Calcofluor concentrations, to determine the minimum required concentration of Calcofluor. It was found that the concentration of Calcofluor could be reduced from 0.115% to 0.0135% without significant loss in the ability to detect flaws, while at the same time significant reductions in Calcofluor outgassing and possible contamination of systems could be realized.

Miller, Michael K.↗

NASA NTRS1998

Evaluation of Low Earth Orbit Environmental Effects on International Space Station Thermal Control Materials

Samples of International Space Station (ISS) thermal control coatings were exposed to simulated low Earth orbit (LEO) environmental conditions to determine effects on optical properties. In one test, samples of the white paint coating Z-93P were coated with outgassed products from Tefzel(R) (ethylene tetrafluoroethylene copolymer) power cable insulation as-may occur on ISS. These samples were then exposed, along with an uncontaminated Z-93P witness sample, to vacuum ultraviolet (VUV) radiation to determine solar absorptance degradation. The Z-93P samples coated with Tefzel(R) outgassing products experienced greater increases in solar absorptance than witness samples not coated with Tefzel(R) outgassing products. In another test, samples of second surface silvered Teflon(R) FEP (fluorinated ethylene propylene), SiO. (where x=2)-coated silvered Teflon(R) FEP, and Z-93P witness samples were exposed to the combined environments of atomic oxygen and VLTV radiation to determine optical properties changes due to these simulated ISS environmental effects. This test verified the durability of these materials in the absence of contaminants.

Dever, Joyce A.↗

NASA NTRS2000

International Space Station External Contamination Status

PResentation slides examine external contamination requirements; International Space Station (ISS) external contamination sources; ISS external contamination sensitive surfaces; external contamination control; external contamination control for pre-launch verification; flight experiments and observations; the Space Shuttle Orbiter waste water dump, materials outgassing, active vacuum vents; example of molecular column density profile, modeling and analysis tools; sources of outgassing induced contamination analyzed to date, quiescent sources, observations on optical degradation due to induced external contamination in LEO; examples of typical contaminant and depth profiles; and status of the ISS system, material outgassing, thruster plumes, and optical degradation.

Mikatarian, Ron↗

NASA NTRS2011

MIRO Observation of Comet C/2002 T7 (LINEAR) Water Line Spectrum

Comet C/2002 T7 (LINEAR) was observed with the Microwave Instrument for Rosetta Orbiter (MIRO) on April 30, 2004, between 5 hr and 16 hr UT. The comet was 0.63AU distance from the Sun and 0.68AU distance from the MIRO telescope at the time of the observations. The water line involving the two lowest rotational levels at 556.936 GHz is observed at 557.070 GHz due to a large Doppler frequency shift. The detected water line spectrum is interpreted using a non local thermal equilibrium (Non-LTE) molecular excitation and radiative transfer model. Several synthetic spectra are calculated with various coma profiles that are plausible for the comet at the time of observations. The coma profile is modeled with three characteristic parameters: outgassing rate, a constant expansion velocity, and a constant gas temperature. The model calculation result shows that for the distant line observation where contributions from a large coma space is averaged, the combination of the outgassing rate and the gas expansion velocity determines the line shape while the gas temperature has a negligible effect. The comparison between the calculated spectra and the MIRO measured spectrum suggests that the outgassing rate of the comet is about 2.0x1029 molecules/second and its gas expansion velocity about 1.2 km/s at the time of the observations.

spectral line↗

NASA NTRSDate not supplied

Obtaining cryogenic molecular transport data for analysis

The James Webb Space Telescope (JWST) has a primary mirror, made of 18 segments, and a secondary mirror (SM) that are used to direct the light of desired targets. While on orbit, the secondary mirror assembly (SMA) was stowed for approximately 10 days and was subject to molecular contamination outgassing from the cavity of the secondary mirror support structure (SMSS) in-board hinge (IBH) which contains cables, motors, resolvers, and coatings. The main concern during this period before SMA deployment is the accumulation of ice due to the lack of a heater on the SMA. The temperature differentials between the IBH surfaces and SMA could cause redistribution of contaminants. To address this concern, single layer insulation (SLI) was used to create adequate venting and path redirection of outgassing from the IBH. Two separate thermal vacuum tests were performed to quantify this contamination: one Z307 ASTM E 1559 materials test of the radiator paint used on the motor of the IBH and a separate test on a primary mirror backplane assembly (PMBA) qualification engineering test unit (ETU) of the IBH. These tests approximately followed the predicted SMA pre-deployment thermal environment. To quantify source rates in case of a leak, the motor and resolver sides were separated and quartz crystal microbalances (QCM) were used to measure the deposition of water. The SLI redesign and implementation and outgassing measurements to understand leak effects from the IBH were essential to mitigate the deposition of contamination on the SMA.

James Webb Space Telescope, contamination, cleanro↗

NASA NTRSDate not supplied

Obtaining Cryogenic Molecular Transport Data for Analysis

James Webb Space Telescope↗

NASA NTRS1996

Graphic Three-Axes Presentation of Residual Gas Analyser Data

Residual gas analyzers (RGA) are commonly used to measure the composition of residual gases in thermal-vacuum test chambers. Measurements from RGAs are often used to identify and quantify outgassing contaminants from a test article during thermal-vacuum testing. RGA data is typically displayed as snapshots in time, showing instantaneous concentrations of ions from ionized residual gas molecules at different atomic masses. A method was devised by the authors to present RGA data in a three-axis format, plotting atomic mass unit (AMU), ion concentration as a function of AMU, and time, to provide a clear graphic visualization ot trends in gas concentration changes and to initiate a valuable analytical tool to interpret test article outgassing rates during thermal-vacuum testing.

data analysis↗

NASA NTRS2016

Evaluation of a Conductive Elastomer Seal for Spacecraft

An electrically conductive elastomer was evaluated as a material candidate for a spacecraft seal. The elastomer used electrically conductive constituents as a means to reduce the resistance between mating interfaces of a sealed joint to meet spacecraft electrical bonding requirements. The compound's outgassing levels were compared against published NASA requirements. The compound was formed into a hollow O-ring seal and its compression set was measured. The O-ring seal was placed into an interface and the electrical resistance and leak rate were quantified. The amount of force required to fully compress the test article in the sealing interface and the force needed to separate the joint were also measured. The outgassing and resistance measurements were below the maximum allowable levels. The room temperature compression set and leak rates were fairly high when compared against other typical spacecraft seal materials, but were not excessive. The compression and adhesion forces were desirably low. Overall, the performance of the elastomer compound was sufficient to be considered for future spacecraft seal applications.

elastomer↗

NASA NTRSDate not supplied

Bakeout Workshop

Spacecraft hardware thermal vacuum exposures and bakeouts have been used for years to reduce molecular outgassing to limit contamination to critical optics and sensors on-ground and in orbit. This presentation will discuss lessons learned and vacuum procedural techniques to make the most of your vacuum time. Quartz Crystal Microbalances (QCMs) and Residue Gas Analyzers (RGA) are 2 devices that help track molecular outgassing and examples will be shown on how to use them for your analytical benefit.

Outgassing thermal vacuum QCM RGA↗

DOE OSTI2020

Predicting 3D moisture sorption behavior of materials from 1D investigations

Abstract Moisture in materials can be a source of future outgassing and exacerbate unwanted changes in physical and chemical properties. Here, we investigate the effect of sample size and shape on the moisture transport phenomena through a combined experimental and modeling approach. Several different materials varying in size and shape were investigated over a wide range of relative humidities (0–90%) and temperatures ( $$30{-}70^{\,\circ } \hbox {C}$$ 30 - 70 ∘ C ) using gravimetric type dynamic vapor sorption (DVS). A dynamic triple-mode sorption model, developed previously, was employed to describe the experimental results with good success; the model includes absorption, adsorption, pooling (clustering) of species, and molecular diffusion. Here we show that the full triple-mode sorption model is robust enough to predict the dynamic uptake and outgassing of 3-dimensional (3D) samples using parameters derived from quasi-1D samples. This successful demonstration on three different materials (filled polydimethylsiloxane (PDMS), unfilled PDMS, and ceramic inorganic composite) illustrates that the model is robust at describing the scale-independent physics and chemistry of moisture sorption and diffusion materials. This work demonstrates that while sorption mechanisms manifest in testing of all sample sizes, some of these mechanisms were so subtle that they were overlooked in our initial modeling and assessment, illustrating the importance of multi-scale experiments in the development of robust predictive capabilities. Our study also outlines the challenges and viable solutions for global optimization of a multi-parameter model. The ability to quantify moisture sorption and diffusion, independent of scale, using 1D lab-scale experiments enables prediction of long-term bulk materials behavior in real applications.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Time-dependent modeling of coupled plasma-wall dynamics

Effects of dynamic wall outgassing on divertor plasma during an ELM-like heat pulse are modelled using newly coupled edge plasma code UEDGE and all reaction-diffusion code FACE. Different divertor regimes are simulated depending on the degree of the plasma detachment. It is shown that hydrogen outgassing from the divertor target plate induced by ELM pulse in the semi-detached regime can trigger deep plasma detachment. The induced detachment does not spontaneously reverse after the pulse due to ineffective implantation of low energy plasma hydrogen in the target material. Furthermore, we demonstrate that plasma neutrals play essential role in heat transport in a detached divertor. The modelled hydrogen dynamics in the wall material demonstrates that the heat pulse leads to enhanced hydrogen transport toward the wall bulk.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Linking impact melt redox with crustal weathering regime

Abstract Impact melting and outgassing of impact melts were important processes shaping the crust and atmosphere of early Earth and Mars. The redox state of impact melts influences the gases they release, but the controls on impact melt redox are not well understood. Here, we present Fe micro–X-ray absorption near edge structure (μ-XANES) measurements of a suite of impact melt glasses from Lonar crater, India. As an impact into continental flood basalts, Lonar crater is an ideal analog for impacts into basaltic crust on early Earth and Mars. The Fe-μ-XANES technique permits robust characterization of the Fe3+/ΣFe ratio and therefore redox conditions in Lonar glasses. We found a range in Fe3+/ΣFe of 0.21–0.49 among Lonar glasses, including substantial intraclast variations. We conclude that a primary factor driving these variations was pre-impact oxidative weathering of target rocks. The coupling between crustal weathering regime and speciation of gases released from impact melts implies that impact melt outgassing could act as a feedback mechanism to reinforce prevailing surface redox conditions.

Geology↗

DOE OSTI2020

Kinetics of TATB and LX-17 Decomposition by Thermal Analysis

The kinetics of TATB decomposition have been investigated by thermal analysis (thermogravimetric analysis, TGA, and differential scanning calorimetry, DSC) at both LLNL and the University of Alabama Birmingham. This report summarizes progress in understanding from those results within the context of identifying the global reaction mechanism, i.e., sequential, autocatalytic, competitive, or some mixture thereof. A particularly important issue is how pressure affects both the reaction rate and enthalpy. The effect of pressure helps identify dominant mechanisms and construct and constrain a global mechanism that will work over a wide range of conditions. This memorandum is simply a snapshot of current progress and not a definitive interpretation. I have written it to organize work of others and my interpretations in a systematic manner with the intention of stimulating further advances in understanding. SDT data comes from Jen Montgomery at LLNL, and high-pressure DSC comes from Victoria Stanford and Sergey Vyazovkin at University of Alabama at Birmingham. Major observations and conclusions, some new and some not, are (1) outgassing below 150 °C prior to decomposition releases adsorbed water vapor, (2) outgassing between 150 and 250 °C may come primarily from intercalated water (3) initial thermal decomposition above 250 °C or so involves dehydration of TATB to create furazans, (4) quickly heating to higher temperatures in open pans with flowing gas leads primarily to TATB evaporation between 270 and 390 °C, (5) using a pinhole crucible at atmospheric pressure largely eliminates TATB sublimation, (6) at typical thermal analysis heat rates, the main stage of decomposition is described by a single mass loss process, and decomposition of residual material is spread over a wide range of thermal severity, (7) at typical thermal analysis heat rates and constant temperatures above 300 °C, heat release occurs in two overlapping peaks, with the first one a little faster than mass loss and the second on a little slower than mass loss, (8) total heat release increases significantly with heating rate and substantially with increased pressure, and (9) isothermal experiments at 340 °C indicate that the first exotherm increases by more with LX-17 than TATB, which suggests a possible chemical role of Kel-F decomposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

High Dose and Dose Rate 60 Co γ-Irradiation of High-Density Polyethylene

We have irradiated high-density polyethylene ribbons and cylinders to ~200 kGy at a dose rate of ~5 kGy day -1 , using a 60 Co source. The radiolytically-generated gas consists almost entirely of H 2 . Based on the time- and dose-dependence of the outgassing, we have determined the radiation- chemical yield for the evolved H 2 , as well as the diffusion coefficient of H 2 in HDPE. We find that the evolved gas yield G evolved depends on the interplay of sample geometry, experimental timescale, and the diffusion coefficient of H 2 in HDPE. When these factors facilitate completion of diffusion prior to gas quantification, such as for sub-mm-thickness ribbons, we measure a time- and dose-invariant value of G evolved = 0.0076 cm 3 std. H 2 J -1 that is in agreement with literature reports. When sample geometry and experiment timescale do not permit completion of diffusion, we measure a time- and dose-dependent value of G evolved . We have developed a model for the transient outgassing behavior of the cylinders, and fitted it to the experimental data. Based on these fits, we estimate a room-temperature diffusivity of D H 2 /HDPE ≈ 1.67 ± 0.12 x 10 -6 cm 2 s -1 for H 2 in HDPE, in good agreement with literature values. At present, the effects of dose rate and γ-photon energy on HDPE gas yield are not known and require further investigation.

36 MATERIALS SCIENCE↗