Search NASA⌕ Search

SEARCH · Search NASA

Results for “parasitics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Cracking vs. surface reactivity in high-nickel cathodes for lithium-ion batteries

High-nickel layered oxide cathodes LiNi x Mn y Co z O 2 (NMC) experience microcracks during cycling. This can expose fresh cathode surfaces for parasitic reactions and isolate active cathode material from the conductive electrode matrix, resulting in impedance increase and capacity fade. The commonly held belief attributes microcracks to anisotropic lattice volume changes of primary particles during cycling. Nevertheless, recent reports suggest that certain electrolytes might reduce microcracks in NMC cathodes during deep cycling. This raises a crucial question on the origin of microcracks: do microcracks exacerbate surface stability, or does poor surface stability contribute to microcrack formation? This perspective aims to provide context and expound this “chicken or egg” dilemma. We contend that the consequence of surface reactivity on the cycle life of high-Ni cathodes is more pronounced than that of particle cracking. Here, we hypothesize that particle cracking is more of a symptom of severe surface reactivity rather than a cause of capacity fade.

25 ENERGY STORAGE↗
DOE OSTI2022

Fabrication methods for high reflectance dielectric-metal point contact rear mirror for optoelectronic devices

The patterned dielectric back contact (PDBC) structure can be used to form a point-contact architecture that features a dielectric spacer with spatially distributed, reduced-area metal point contacts between the semiconductor back not recognized contact layer and the metal back contact. In this structure, the dielectric-metal region provides higher reflectance and is electrically insulating. Reduced-area metal point contacts provide electrical conduction for the back contact but typically have lower reflectance. The fabrication methods discussed in this article were developed for thermophotovoltaic cells, but they apply to any III-V optoelectronic device requiring the use of a conductive and highly reflective back contact. Patterned dielectric back contacts may be used for enhanced sub-bandgap reflectance, for enhanced photon recycling near the bandgap energy, or both depending on the optoelectronic application. The following fabrication methods are discussed in the article: PDBC fabrication procedures for spin-on dielectrics and commonly evaporated dielectrics to form the spacer layer; methods to selectively etch a parasitically absorbing back contact layer using metal point contacts as an etch mask; methods incorporating a dielectric etch through different process techniques such as reactive ion and wet etching.

14 SOLAR ENERGY↗
DOE OSTI2023

Anion modification for stable solid electrolyte interphase in anode-free lithium metal batteries

The durability of anode-free Li metal batteries is largely limited by the undesired Li plating/stripping irreversibility on the current collector due to the infinite volume change, uncontrollable Li dendrite growth, and continuous parasitic reactions between Li metal and the electrolyte. To address these challenges, the formation of a stable and robust solid electrolyte interphase (SEI) with high ionic conductivity and strong mechanical strength is critical. Here, we developed an advanced electrolyte by introducing LiNO 3 into the localized high concentration electrolyte (LHCE) with lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2-dimethoxyethane (DME) solvent, and 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TFTE) diluent to in situ construct a LiF and Li x N y O z co-enriched passivation layer on the Cu current collector. The synergetic effect of high mechanical strength of LiF and high ionic conductivity of Li x N y O z endows the Li metal anode with a high Coulombic efficiency (CE) of 99.35%. In conclusion, in anode-free Li metal pouch cell using LiFePO 4 (LFP) as a cathode holds an exceptionally improved capacity retention under the charging/discharging rate of 1/3 C, demonstrating great promise for developing dendrite-free and safe Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

The surface triple-coupling on single crystalline cathode for lithium ion batteries

Single crystalline (SC) cathode materials, which are less susceptible to micro/nano-cracks formation and offer better structure stability compared to the polycrystalline counterpart, have attained great attention. However, the parasitic side reactions at the cathode-electrolyte interface induces the loss of active species, which consequently leads to continual degradation of the electrochemical performances. Herein, a triple coupling of concentration-gradient Na+, F- co-doping and surface NaF coating are exploited for the first time on SC LiNi 0.5C o 0.2 Mn 0.3 O 2 cathode by the hydrolysis of NaPF 6 . This process regulates the external structure of materials by constructing a “sandwich” configuration from surface to bulk: rock salt - mixing zone - layered phase. The detailed interface transformation mechanism is revealed by Neutron powder diffraction (NPD), spherical aberration corrected high-resolution scanning transmission electron microscopy (HR-STEM), electron energy loss spectroscopy (EELS), and Ar+ sputtering assisted X-ray photoelectron spectroscopy (XPS). The synergistic effects endow the SC cathode with outstanding capacity retentions: 91.3% at 25 °C and 85% at 45 °C, after 500 cycles at 5 C between 3.0 and 4.5 V. In addition, a high full-cell reversible capacity of 168.9 mAh g -1 with a capacity retention of 92.4% is achieved after 300 cycles at 1 C. Multiple characterizations further indicate that these superior results are mainly ascribed to the overall structure integrity of SC material, the thin cathode electrolyte interface, high content of lithium fluoride, and the low solubility of transition metal ions. This work opens a new avenue to construct a benign interface towards high-performance lithium ion batteries.

lithium ion batteries↗
DOE OSTI2023

In situ microscopy and spectroscopy characterization of microsized Sn anode for sodium-ion batteries

Microsized Sn is a promising anode material for sodium-ion batteries in terms of cost, specific capacity, and volumetric energy density, which however suffers from huge volume changes and rapid cell degradation upon cycling. Despite recent advances via nanostructured electrode design and interface engineering, the correlation between mechanical stability, solid-electrolyte interphase (SEI) and reaction kinetics/reversibility remains controversial and elusive. Here, in this work, by combining in situ scanning electron microcopy and X-ray absorption spectroscopy as well as X-ray photoelectron spectroscopy, we have investigated the underlying electro-chemo-mechanical behavior and their coupling effects during charge/discharge of microsized Sn anode. Our results revealed that microsized Sn is pulverized into nanoparticles with simultaneous formation of numerous voids and pores upon the 1st charge/discharge, while the electrolytes composition plays a critical role on the consequent parasitic reactions and eventually the sodiation/de-sodiation reversibility. In contrast to carbonate-based electrolytes, ether-based electrolytes enabled formation of inorganic species dominated SEI with improved mechanical strength, thus leading to higher specific capacity and improved cycling stability. The present findings are crucial for future development of microsized anode materials for rechargeable batteries with high volumetric energy density.

25 ENERGY STORAGE↗
DOE OSTI2024

Structural and chemical evolutions of a magnesium vanadium oxide cathode under electrochemical cycling in magnesium batteries

The design of cathode materials that remain chemically and structurally stable during repetitive ion insertion and extraction poses a significant challenge in developing multivalent batteries. The cycling stability of traditional metal oxide-based cathode is challenged by sluggish diffusion of multivalent cations and parasitic reactivity at interfacial regimes, including the cathode electrolyte interphase layer (CEI). Understanding the reactions at the cathode-electrolyte interface, particularly those induced by non-stoichiometric surface layers, is a crucial design parameter for both cathode materials and electrolytes. Here, in this study, we employed multimodal analysis, including in situ and ex situ X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (TEM) and electrochemical impedance spectroscopy (EIS) to examine the surface reactions and subsequent structural and chemical evolutions of the CEI on high voltage magnesium vanadium oxide (MgV 2 O 4 ) spinel cathode during the Mg 2+ insertion/extraction processes. The results revealed that the presence of non-stoichiometric surface layers in the magnesium vanadium oxide cathode drive the decomposition of bis(trifluoromethanesulfonyl)imide (TFSI - ) anion, leading to the formation of the CEI layer. The CEI layer could inhibit the Mg 2+ ion transfer processes. Accompanying this reactivity-driven degradation, the magnesium vanadium oxide cathode undergoes pulverization, forming clusters of nanosized particles. This process likely improves cycling ability by creating new intercalation sites and shortening the diffusion pathway for the Mg 2+ cations. This study demonstrates that controlling surface stoichiometry and engineering morphological properties are critical design parameters for high performance cathodes for multivalent batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

The role of Li doping in layered/layered Na x Li y Ni 0.4 Fe 0.2 Mn 0.4 O 2 intergrowth electrodes for sodium ion batteries

Here, the layered NaTMO 2 (TM = Ni, Fe, Mn) materials with the O3-type structure are attractive as positive electrodes for sodium ion batteries because of their high theoretical capacity. Additionally, Li doping in these materials has been shown to offer substantial enhancements to their electrochemical properties by promoting the formation of intergrowth structures, which are combinations of specific phases. However, the mechanism by which the intergrowth modifies the electrochemical properties is often unclear. Systematic variation of Li content in Na x Li y Ni 0.4 Fe 0.2 Mn 0.4 O 2 (NFM-Li y ) was conducted to identify its role in structural modification and electrochemical performance. Li contents of 0.15 and greater generate a layered/layered Na-O3/Li-O’3 intergrowth structure. 7 Li and 23 Na nuclear magnetic resonance and x-ray absorption spectroscopy identify that when the total solubility for alkali ions in the layered structure is exceeded, Li continues to form the Li-O’3 phase while the excess Na forms residual sodium compounds such as Na 2 O. Higher Li content is associated with improved capacity retention in the initial cycles from the superior stability of the mechanically linked NaO3/Li-O’3 structure that suppresses the P3 to OP2 phase transition during charge. However, high Li contents are associated with increased rates of parasitic side reactions that reduce long-term cycling stability. These side reactions are associated with the instability of the cathode-electrolyte interphase, which can be partially mitigated by atomic layer deposition (ALD) coating with alumina, which significantly enhances the capacity retention and Coulombic efficiency over many cycles. Overall, we find that the layered/layered Na-O3/Li-O’3 intergrowth structure is able to provide structural stability and suppress undesired phase transformations but is overwhelmed by the increased reactivity of the surface if not protected by surface coating.

25 ENERGY STORAGE↗
DOE OSTI2024

Advanced manufacturing of 3D custom boron-carbide collimators designed for complex environments for neutron scattering

Scattered-beam collimation is a very useful method to reduce unwanted backgrounds and to boost the desired sample signal instead. This approach is of particular interest for samples contained within a complex environment that gives rise to much unwanted parasitic scatter. As neutron scattering instrument and techniques advances, small samples are becoming of more and more interest, which necessitates optimized collimation. Here, in this work, we describe a concept for the design and fabrication of advanced scattered-beam collimation 3D printed from B 4 C specifically tailored for samples contained within a complex environment. This concept is demonstrated through the use of a diamond anvil cell for high pressure experimentation, a technique that very typically requires small samples. The collimators here are designed through a modeling procedure via Monte Carlo neutron ray tracing that encompasses the entire system: the instrument, the complex environment and the collimator. Since the first approach of simply scaling up of the print-size was not successful, a novel concept of a multi-part alternate-blade collimator was developed. This approach addresses printing constraints but gives greater flexibility in design. Its performance is computationally compared against an unprintable progressively tighter blade collimator to assess the effect of alternating blades. No strong difference was observed. Its performance was validated through experimentation at the Spallation Neutron Source. The results emphasize the critical importance of ultra-high precision alignment while showing good overall agreement between simulation and experiment and underscore the feasibility of the method and its real-world application.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Investigations on the multiple-sector hard-copper X-band accelerating structures

The development of advanced, high gradient accelerating structures is one of the leading activity of the particle accelerator community. In the technological research of new construction methods for these devices, high-power testing is a critical step for the verification of their viability. Recent experiments showed that accelerating cavities made out of hard copper, fabricated without high-temperature processes, can achieve better performance as compared with soft copper ones. Recently, we have built cavities using Tungsten Inert Gas welding and the high-power experiments confirmed that this joining process is a robust and low-cost alternative to brazing or diffusion bonding. This is a good solution for high-gradient operation, with a gradient of about 150 MV/m in X-band, at a breakdown rate of 10 -3 /pulse/meter using a shaped RF pulse with a 150 ns flat part. We continue the design, construction and high power tests of three-cells standing-wave X-band accelerating cavities fabricated with a split-open geometry, made of hard copper and vacuum-sealed by welding. Our aim is the fabrication of accelerating structures made out of hard copper alloys by using innovative cost-effective technologies. Moreover, our method of multiple-sector structures opens the way to new technological approaches and design methods, for example providing the possibility of placing dampers of the parasitic higher-order modes. Such structures with dampers allow for acceleration of multi-bunch beams, both in standing and in travelling-wave accelerating modality. Here, this paper describes the design of two cavities made of multiple sectors that were fabricated at the Italian Institute for Nuclear Physics in Frascati, Italy (INFN-LNF), assembled by means of clamping and then joined with the Tungsten Inert Gas welding in order to preserve the hardness of the metal. These are three-cell standing-wave X-band accelerating cavities, to be operated in the π-mode. We report the low-power RF tests of the first one, made of two halves, and the RF design of the second one, made of four quadrants. Both structures were built for high-gradient tests at SLAC National Accelerator Laboratory.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Single channel PICOSEC Micromegas detector with improved time resolution

This paper presents design guidelines and the experimental verification of a single-channel PICOSEC Micromegas (MM) detector with an improved time resolution. The design encompasses the detector board, vessel, auxiliary mechanical parts, and electrical connectivity for high voltage (HV) and signals, focusing on improving the stability, reducing noise, and ensuring signal integrity to optimize timing performance. A notable feature is the simple and fast reassembly procedure, facilitating quick replacement of the detector internal components that allows for an efficient measurement strategy involving different detector components. The paper also examines the influence of parasitic capacitance and inductance on the output signal integrity. To validate the design, a prototype assembly and three interchangeable detector boards with varying readout pad diameters were manufactured. Detectors were initially tested in the laboratory. Finally, the timing performance of the detectors with different pad sizes was verified using 150 GeV muons. Notably, a record time resolution for a PICOSEC Micromegas detector technology with a CsI photocathode of 12.5 ± 0.8 ps was achieved for a detector with 10 mm diameter readout pad size.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Glacial geology of the Hudson Mountains, Amundsen Sea sector, West Antarctica

The Hudson Mountains are situated in the eastern Amundsen Sea sector of the West Antarctic Ice Sheet, adjacent to Pine Island Glacier. They form a volcanic field of 17 stratovolcanoes and parasitic vents, preserved as nunataks. Two former tributaries of Pine Island Glacier (Larter and Lucchitta glaciers) flow through the mountains. Here we present a detailed study of the glacial geology of the area. We describe field observations and measurements of geomorphological features from 15 of the nunataks, meltwater ponds found on the surface of three nunataks and supraglacial features (ice dolines) from two sites near the present grounding line. Together these provide constraints on the past ice sheet extent, flow pathways and thermal regime, and enhance our understanding of the present hydrological regime – all of which are important as context for the observed modern ice sheet behaviour. We find evidence suggesting that all nunataks in the Hudson Mountains were covered by ice during the Last Glacial Maximum (defined here as 26.5-19 ka) and have since deglaciated. Faceted and polished erratic cobbles and boulders of exotic lithologies (syenites, alkali granites, granites, granodiorites, tonalites and gabbros) are numerous and perched on nunatak surfaces. A marked difference between the dominant erratic lithologies on nunataks adjacent to Pine Island Glacier (granite) and Lucchitta Glacier (granodiorite-tonalite) indicates that the ice sheet was transporting clasts from at least two distinct upstream source regions. The similarity in degree of weathering suggests, however, that all the erratics were transported by one phase of (warm-based) glaciation; their presence on or close to the summits of all except one nunatak indicates that the ice sheet during that time was at least 700 m thicker than present. These results are consistent with ice sheet model simulations which suggest that all nunataks in the Hudson Mountains were completely submerged by the Last Glacial Maximum ice sheet.

58 GEOSCIENCES↗
DOE OSTI2020

Stable magnesium zinc oxide by reactive Co-Sputtering for CdTe-based solar cells

Magnesium zinc oxide (MZO) is a promising front contact material for CdTe solar cells. Due to its higher band gap than traditional CdS, MZO can reduce parasitic absorption to significantly increase short-circuit current density while also providing a benefit of conduction band offset tuning through Mg:Zn ratio optimization. MZO has been successfully implemented into CdTe devices, however its stability has been of concern. The MZO stability issue has been attributed to the presence of oxygen in the CdTe device processing ambient, leading to double-diode behavior (S-kink) in the current density-voltage curves. Here we report on MZO thin films deposited by reactive co-sputtering. The reactively co-sputtered MZO thin films have encouraging stability, show no significant variation in work function of the surface over a period of 6 months, as measured by Kelvin probe. Energy conversion efficiencies of around 16% have been achieved both with and without presence of oxygen in device processing ambients across multiple research facilities. Finally, these efficiencies should be possible to increase further by tuning of the thin film deposition and device processing parameters, especially through optimization of the back contact.

14 SOLAR ENERGY↗
DOE OSTI2020

Reactive ion etched, self-aligned, selective area poly-Si/SiO 2 passivated contacts

Front/back poly-Si/SiO 2 contact devices suffer from low short-circuit current density, J sc , due to parasitic optical absorption in the front poly-Si layer. Thin poly-Si (~20 nm) allows for high J sc but is not compatible with screen-printed fire-through contacts. We therefore study the effects of post-deposition etching of a thick poly-Si (200 nm) front layer by reactive ion etching (RIE) using the metal grid lines as a self-aligned mask. We show that passivation is maintained in the device during RIE and that J sc is increased by a gain in the blue quantum efficiency response. However, our specific etching parameters cause non-uniform etching of the poly-Si leading to premature loss of passivation without optimal gain in J sc . Etched, unpassivated layers can be re-passivated with a H-containing dielectric layer leading to a gain in Jsc, open circuit voltage, V oc , Fill-Factor, FF, and efficiency.

14 SOLAR ENERGY↗
DOE OSTI2022

GaAs Thermophotovoltaic Patterned Dielectric Back Contact Devices with Improved Sub-Bandgap Reflectance

We demonstrate GaAs thermophotovoltaic (TPV) devices with a patterned dielectric back contact (PDBC) architecture, featuring a dielectric spacer between the semiconductor and back metal contact over most of the back surface for high reflectance, and metal point contacts over a smaller area for electrical conduction. In the TPV application, high sub-bandgap reflectance is needed to reflect unused sub-bandgap photons to the thermal emitter to minimize energy losses in this portion of the thermal spectrum. We explore different PDBC fabrication processes with SU-8 and SiO2 dielectric spacer layers to maximize sub-bandgap reflectance while minimizing series resistance to increase TPV conversion efficiency. We successfully demonstrate GaAs SU-8 PDBC TPV devices with 2200 degrees C blackbody-weighted sub-bandgap reflectance of 94.9% and 96.5% with and without a front metal grid, respectively. This is 0.7% and 2.3% (absolute) higher than the mean sub-bandgap reflectance of 94.2% for GaAs baseline TPV devices with 100% Au back contact with front metal grid. Lower sub-bandgap reflectance in TPV devices with front grids indicates the front grid induces light scattering leading to additional parasitic absorption in the TPV device. We also show that for higher contact coverage fractions, the PDBC reflectance cannot in general be treated by a linear interpolation using simple 1D transfer matrix method modeling and should be treated instead as a diffraction grating by solving Maxwell's equations in 3D.

energy storage↗
DOE OSTI2024

Photon management in silicon photovoltaic cells: A critical review

With the practical efficiency of the silicon photovoltaic (PV) cell approaching its theoretical limit, pushing conversion efficiencies even higher now relies on reducing every type of power loss that can occur within the device. Limiting optical losses is therefore critical and requires effective management of incident photons in terms of how they interact with the device. Ultimately, photon management within a PV cell means engineering the device and constituent materials to maximize photon absorption within the active semiconductor and therefore reduce the number of photons lost through other means, most notably reflection and parasitic absorption. There have been great advancements in the front and the rear side photon management techniques in recent years. This review aims to discuss these advancements and compare the various approaches, not only in terms of increases in photogenerated current, but also their compatibility with different PV cell architectures and potential trade-offs, like increased surface recombination or scalability for high-volume manufacturing. In this review, a comprehensive discussion of a wide variety of the front and the rear side photon management structures are presented with suggestions to improve the already achieved performance further. Here, this review is unique because it not only presents the recent development in photon management techniques, but also offers through analysis of these techniques and pathways to improve further.

14 SOLAR ENERGY↗
DOE OSTI2024

Patterned dielectric back contact design for GaAs thermophotovoltaic devices

-Patterned-dielectric back contact structures in optoelectronic devices are designed to boost the reflectance of light from the device back surface while retaining a low-resistance pathway for electrical conductance. Their reduced light absorption at near- and sub-bandgap photon energies leads to improved luminescence in light-emitting diodes, greater photon recycling, voltage, and efficiency in photovoltaic cells, and greater recuperation of unabsorbed sub-bandgap light in thermophotovoltaic (TPV) systems. However, diffraction from the patterned features can deflect incident light in propagation directions that lead to light trapping and parasitic absorption in the cell. Here, in this article, we use rigorous coupled-wave analysis (RCWA) to study three-dimensional diffractive scattering of electromagnetic waves by periodic metal point-contact gratings on 1.42-eV GaAs TPV cells, to analyze their effect on unwanted sub-bandgap absorption in order to achieve higher TPV system efficiency. Solutions of Maxwell's equations calculated using RCWA are compared to measured sub-bandgap reflectance in experimental GaAs TPV devices with varying metal point-contact diameters and spacing. Modeling and experiments indicate decreased total reflectance due to these diffractive effects for a small point contact diameter of 1 μm, and this effect is much stronger at higher contact coverage fractions.

14 SOLAR ENERGY↗
DOE OSTI2025

Investigation of electrode-electrolyte interfaces to enable non-flammable Li-ion batteries operating up to 125°C with liquid electrolyte

Non-flammable and high-temperature stable ionic liquid (IL)-based electrolytes could eliminate catastrophic battery failures and improve battery safety, but their poor electrochemical interaction with the LiNi x Mn y Co z O 2 (NMC) family of cathodes is a long-standing problem due to severe parasitic reactions at high temperature. Understanding surface and bulk structural mechanisms of NMC-type cathodes at elevated operational temperature is of paramount importance to facilitate stable electrochemical performance. Here, we report a non-flammable phosphonium IL-based cell chemistry that offers stable electrode-electrolyte interfaces, leading to electrochemical performance up to 125°C and high-temperature safety. We combine electrochemistry with multimodal X-ray spectroscopy methods to understand interfaces at elevated temperature (100°C). This nanoscale understating enables a proof-of-concept high-temperature cylindrical cell (14500), and the design achieves an average Coulombic efficiency of ≈99.5% up to 300 cycles at 100°C. The results ascertain the significance of depth-dependent degradation at the interface, guiding room-temperature Li-ion technology toward extreme-temperature applications.

36 MATERIALS SCIENCE↗