Search NASA⌕ Search

SEARCH · Search NASA

Results for “patch antenna”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Coplanar waveguide feeds for phased array antennas

The design and performance of the following coplanar waveguide (CPW) microwave distribution networks for linear as well as circularly polarized microstrip patches and printed dipole arrays is presented: (1) CPW/microstrip line feed; (2) CPW/balanced stripline feed; (3) CPW/slotline feed; (4) grounded CPW (GCPW)/balanced coplanar stripline feed; and (5) CPW/slot coupled feed. Typical measured radiation patterns are presented, and their relative advantages and disadvantages are compared.

Simons, Rainee N.↗
NASA NTRS1979

Rough surface wavelength measurement through self mixing of Doppler microwave backscatter

A microwave backscatter technique is presented that has the ability to sense the dominant surface wavelength of a random rough surface. The purpose of this technique is to perform this measurement from an aircraft or spacecraft, wherein the horizontal velocity of the radar is an important parameter of the measurement system. Attention will be directed at water surface conditions for which a dominant wavelength can be defined, then the spatial variations of reflectivity will have a two dimensional spectrum that is sufficiently close to that of waves to be useful. The measurement concept is based on the relative motion between the water waves and a nadir looking radar, and the fact that while the instantaneous Doppler frequency at the receiver returned by any elementary group of scatterers on a water wave is monotonically changing, the difference in the Doppler frequency between any two scattering 'patches' stays approximately constant as these waves travel parallel to the major axis of an elliptical antenna footprint. The results of a theoretical analysis and a laboratory experiment with a continuous wave (CW) radar that encompasses several of the largest waves in the illuminated area show how the structure in the Doppler spectrum of the backscattered signal is related to the surface spectrum and its parameters in an especially direct and simple way when an incoherent envelope detector is the receiver.

Weissman, D. E.↗
NASA NTRS1999

Design of a Foldable Low-loss Microstrip Array Antenna

The design and analysis of a series-fed, foldable microstrip array antenna for radiometer applications is presented. The array antenna is composed of two equal sub arrays. Each sub array consists of a series of patches connected together through segments of microstrip lines. The sub arrays are fed 180 degree out of phase to ensure a symmetric radiation pattern. The design approach, is accomplished using the IE3D code that utilizes the method of moments. All experimental and simulated data are presented and discussed.

Christodoulou, C. G.↗
NASA NTRS1993

Resonant frequencies of irregularly shaped microstrip antennas using method of moments

This paper describes an application of the method of moments to determine resonant frequencies of irregularly shaped microstrip patches embedded in a grounded dielectric slab. For analysis, the microstrip patch is assumed to be excited by a linearly polarized plane wave that is normal to the patch. The surface-current density that is induced on the patch because of the incident field is expressed in terms of subdomain functions by dividing the patch into identical rectangular subdomains. The amplitudes of the subdomain functions, as a function of frequency, are determined using the electric-field integral equation (EFIE) approach in conjunction with the method of moments. The resonant frequencies of the patch are then obtained by selecting the frequency at which the amplitude of the surface-current density is real. The resonant frequencies of the equilateral triangular and other nonrectangular patches are computed using the present technique, and these frequencies are compared with measurements and other independent calculations.

Deshpande, Manohar D.↗
NASA NTRS1991

Coplanar waveguide feeds for phased array antennas

The design and performance is presented of the following Coplanar Waveguides (CPW) microwave distribution networks for linear as well as circularly polarized microstrip patches and dipole arrays: (1) CPW/Microstrip Line feed; (2) CPW/Balanced Stripline feed; (3) CPW/Slotline feed; (4) Grounded CPW/Balanced coplanar stripline feed; and (5) CPW/Slot coupled feed. Typical measured radiation patterns are presented, and their relative advantages and disadvantages are compared.

Simons, Rainee N.↗
NASA NTRS1991

Coplanar waveguide feeds for phased array antennas

The design and performance is presented of the following coplanar waveguides (CPW) microwave distribution networks for linear as well as circularly polarized microstrip patches and dipole arrays: (1) CPW/microstrip line feed; (2) CPW/balanced stripline feed; (3) CPW/slotline feed; (4) grounded CPW/balanced coplanar stripline feed; and (5) CPW/slot coupled feed. Typical measured radiation patterns are presented, and their relative advantages and disadvantages are compared.

Simons, Rainee N.↗
NASA NTRS1998

Design of a low-loss series-fed microstrip array antenna

The design and analysis of a series-fed, low-loss, inverted microstrip array antenna, operating at 1.413 GHz is presented. The array antenna is composed of two sub arrays. Each sub array consists of an equal number of microstrip patches all connected together through a series microstrip line. The first element of each sub array is coaxially fed but 180 degree out of phase. This approach ensures a symmetric radiation pattern. The design approach, is accomplished using the IE3D code that utilizes the method of moments. All experimental and simulated data are presented and discussed.

Mahbub, M. R.↗
NASA NTRS1998

A Microstrip Reflect Array Using Crossed Dipoles

Microstrip reflect arrays offer a flat profile and light weight, combined with many of the electrical characteristics of reflector antennas. Previous work [1]-[7] has demonstrated a variety of microstrip reflect arrays, using different elements at a range of frequencies. In this paper we describe the use of crossed dipoles as reflecting elements in a microstrip reflectarray. Theory of the solution will be described, with experimental results for a 6" square reflectarray operating at 28 GHz. The performance of crossed dipoles will be directly compared with microstrip patches, in terms of bandwidth and loss. We also comment on the principle of operation of reflectarray elements, including crossed dipoles, patches of variable length, and patch elements with tuning stubs. This research was prompted by the proposed concept of overlaying a flat printed reflectarray on the surface of a spacecraft solar panel. Combining solar panel and antenna apertures in this way would lead to a reduction in weight and simpler deployment, with some loss of flexibility in independently pointing the solar panel and the antenna. Using crossed dipoles as reflectarray elements will minimize the aperture blockage of the solar cells, in contrast to the use of elements such as microstrip patches.

Pozar, David M.↗
NASA NTRS1985

Dual-band reactively loaded microstrip antenna

A previously derived theory is applied to a microstrip antenna with a reactive load to produce a dual-band radiator. A model consisting of a rectangular patch radiator loaded with a variable length short-circuited coaxial stub was investigated experimentally. Comparisons of theoretical predictions and experimental data are made for the impedance and resonant frequencies as a function of the position of the load, the length of the stub, and the characteristic impedance of the stub.

Richards, W. F.↗
NASA NTRS1995

Compact, low profile antennas for MSAT and mini-M and Std-M land mobile satellite communications

CAL Corporation has developed a new class of low profile radiating elements for use in planar phased array antennas. These new elements have been used in the design of a low cost, compact, low profile antenna unit for MSAT and INMARSAT Mini-M land mobile satellite communications. The antenna unit which measures roughly 32 cm in diameter by 5 cm deep incorporates a compact LNA and diplexer unit as well as a complete, low cost, beam steering system. CAL has also developed a low profile antenna unit for INMARSAT-M land mobile satellite communications. A number of these units, which utilize a microstrip patch array design, were put into service in 1994.

Strickland, P. C.↗
NASA NTRS1984

The study of microstrip antenna arrays and related problems

The work on rectangular microstrip antennas for dual frequency operation is reported on. The principle of this approach is based on the excitation of a patch for two or more different modes which correspond to different frequencies. However, for a given geometry, the modal frequencies have a fixed relationship; therefore, the usefulness of such a design is greatly limited. In this study three different methods have been contrived to control the frequency ratio over a wide range. First, as found prevously, if shorting pins are inserted at certain locations in the patch, the low frequency can be raised substantially. Second, if slots are cut in the patch, the high frequency can be lowered considerably. By using both techniques, the two frequency ratio can be varied approximately from 3 to 1.3. After that, the addition of more pins or slots becomes ineffective.

Lo, R. Q.↗
NASA NTRS2001

The development of inflatable array antennas

Inflatable array antennas are being developed to significantly reduce the mass, the launch vehicle's stowage volume, and the cost of future spacecraft systems. Three inflatable array antennas, recently developed for spacecraft applications, are a 3.3 m x 1.0 m L-band synthetic-aperture radar (SAR) array, a 1.0 m-diameter X-band telecom reflectarray, and a 3 m-diameter Ka-band telecom reflectarray. All three antennas are similar in construction, and each consists of an inflatable tubular frame that supports and tensions a multi-layer thin-membrane RF radiating surface with printed microstrip patches. The L-band SAR array achieved a bandwidth of 80 MHz, an aperture efficiency of 74%, and a total mass of 15 kg. The X-band reflectarray achieved an aperture efficiency of 37%, good radiation patterns, and a total mass of 1.2 kg (excluding the inflation system). The 3 m Ka-band reflectarray achieved a surface flatness of 0.1 mm RMS, good radiation patterns, and a total mass of 12.8 kg (excluding the inflation system). These antennas demonstrated that inflatable arrays are feasible across the microwave and millimeter-wave spectrums. Further developments of these antennas are deemed necessary, in particular, in the area of qualifying the inflatable structures for space-environment usage.

Inflatable array antennas↗
NASA NTRS1991

Mutual impedance of parallel and perpendicular coplanar surface monopoles

One dimensional integral formulas are derived for mutual impedance of arbitrary size, coplanar, parallel, and perpendicular surface monopoles. The integrals in formulas are expressed as exponential integrals where possible. The mutual impedance expression for parallel monopoles is a summation of exponential integrals and one-dimensional integrals. For perpendicular monopoles, the mutual impedance is in closed form, containing exponential integrals only. The final expressions are in a form suitable for numerical computation. Since the expressions contain at most one-dimensional integrals, they can be utilized to reduce the matrix filling time in the moment method formulations, especially when inhomogeneous sectioning is preferred. Additionally, they can be used in rectangular surface patch modeling of conducting surfaces with edges which are at an angle to the surface patches, providing the angle is small. To this end, the expressions were utilized in the moment method analysis of linearly tapered slot antennas. Very good accuracy was obtained with a reduction in computer time.

Koksal, Adnan↗
NASA NTRS2000

A Dual Polarization, Active, Microstrip Antenna for an Orbital Imaging Radar System Operating at L-Band

A highly successful Earth orbiting synthetic antenna aperture radar (SAR) system, known as the SIR-C mission, was carried into orbit in 1994 on a U.S. Shuttle (Space Transportation System) mission. The radar system was mounted in the cargo bay with no need to fold, or in any other way reduce the size of the antennas for launch. Weight and size were not limited for the L-Band, C-Band, and X-Band radar systems of the SIR-C radar imaging mission; the set of antennas weighed 10,500 kg, the L-Band antenna having the major share of the weight. This paper treats designing an L-Band antenna functionally similar to that used for SIR-C, but at a fraction of the cost and at a weight in the order of 250 kg. Further, the antenna must be folded to fit into the small payload shroud of low cost booster rocket systems. Over 31 square meters of antenna area is required. This low weight, foldable, electronic scanning antenna is for the proposed LightSAR radar system which is to be placed in Earth orbit on a small, dedicated space craft at the lowest possible cost for an efficient L- Band radar imaging system. This LightSAR spacecraft radar is to be continuously available for at least five operational years, and have the ability to map or repeat-map any area on earth within a few days of any request. A microstrip patch array, with microstrip transmission lines heavily employed in the aperture and in the corporate feed network, was chosen as the low cost approach for this active dual-polarization, 80 MHz (6.4%) bandwidth antenna design.

Kelly, Kenneth C.↗
NASA NTRS1999

A Dual Polarization, Active, Microstrip Antenna for an Orbital Imaging Radar System Operating at L-Band

A highly successful Earth orbiting synthetic antenna aperture radar (SAR) system, known as the SIR-C mission, was carried into orbit in 1994 on a U.S. Shuttle (Space Transportation System) mission. The radar system was mounted in the cargo bay with no need to fold, or in any other way reduce the size of the antennas for launch. Weight and size were not limited for the L-Band, C-Band, and X-Band radar systems of the SIR-C radar imaging mission; the set of antennas weighed 10,500 kg, the L-Band antenna having the major share of the weight. This paper treats designing an L-Band antenna functionally similar to that used for SIR-C, but at a fraction of the cost and at a weight in the order of 250 kg. Further, the antenna must be folded to fit into the small payload shroud of low cost booster rocket systems. Over 31 square meters of antenna area is required. This low weight, foldable, electronic scanning antenna is for the proposed LightSAR radar system which is to be placed in Earth orbit on a small, dedicated space craft at the lowest possible cost for an efficient L-Band radar imaging system. This LightSAR spacecraft radar is to be continuously available for at least five operational years, and have the ability to map or repeat-map any area on earth within a few days of any request. A microstrip patch array, with microstrip transmission lines heavily employed in the aperture and in the corporate feed network, was chosen as the low cost approach for this active dual-polarization, 80 MHz (6.4%) bandwidth antenna design.

Kelly, Kenneth C.↗
NASA NTRS1997

Microstrip Reflectarray with Elements Having Variable Rotation Angles

Two Ka-band, half-meter diameter, circularly polarized microstrip reflectarrays have been developed. Although both antennas demonstrated excellent efficiencies, adequate bandwidths, and low average sidelobe and cross-pol levels, the one with variable rotation angles achieved superior overall performance. It is believed that these are electrically the largest microstrip reflectarrays (6924 elements with 42 dB gain) ever developed. It is also the first time that circular polarization has been actually demonstrated using microstrip patch elements. All these reflectarrays have dual-linear and dual-circular polarization capabilities, but only linear polarizations were demonstrated.

antennas↗
NASA NTRS2000

Development of a Two Dimensional Synthetic Aperture Radiometer at L-Band

A radiometer that uses aperture synthesis in two dimensions is being built as part of research under NASA's Instrument Incubator Program. The instrument development team consists of engineers at the Goddard Space Flight Center, the University of Massachusetts and Quadrant Engineering. This will be an aircraft instrument operating at L-band which builds on the heritage of Electronically Steered Thinned Array Radiometer (ESTAR). This instrument is a next step in the development of aperture synthesis (STAR technology) to meet the goal of a future mission to monitor soil moisture globally from space. The instrument will be designed to fly on the NASA P-3 aircraft in a nadir pointing mode, although other options are possible. The antenna will consist of an array of modules in a rectangular grid. Each module will be comprised of a printed circuit dual-polarized patch and integrated receiver. The distribution of modules within the rectangular array will be adjustable so that several different imaging configurations (e.g. '+', 'Y', 'T') can be employed. The integrated receiver will provide amplification and conversion to infrared (IF). The IF signal will be routed to a processor where the required correlations performed. The I and Q channels will be created digitally and the correlations will be done digitally in this processor. The digitization will be done with sufficient bits to study the effects of quantization on radiometer performance. A computer/controller will store the data for conversion to an image and will also perform temperature control and other data interfacing and housekeeping tasks. The design of critical components has been completed and hardware is being assembled to test the individual elements. It is expected that a complete two-channel correlator will be tested by the end of 2000 and that the complete instrument will be ready for flight tests the following summer (2001).

LeVine, D. M.↗
NASA NTRS2006

The Primordial Anisotropy Polarization Pathfinder Array (PAPPA): Instrument Overview and Status

PAPPA is a balloon-based experiment designed to measure the polarization of the Cosmic Microwave Background using candidate technology for an eventual Inflation Probe mission. It will survey a 20 x 20 degree patch of sky with 1 degree angular resolution covering 3 passbands centered at 100,200 and 300 GHz. Detection will be accomplished via antenna-coupled transition edge sensors (TESs) with SQUID-based readouts. In the eventual flight package, band defining filters and MEMS-based polarization modulators will be incorporated into the superconducting microstrip transmission lines that terminate in resistors that are thermally coupled to the TESs. The MEMS switches will allow on-chip polarization modulation that is faster than significant detector gain variations. The initial configuration will incorporate a simplified focal plane augmented by quasioptical polarization modulation. We describe the overall instrument design and present a summary of the current progress.

Chuss, David↗