Search NASA⌕ Search

SEARCH · Search NASA

Results for “pilot modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Transport aircraft flying qualities activities

The optimal control model for pilot vehicle systems was used to develop a methodology for predicting pilot ratings for commercial transports. The method was tested by applying it to a family of transport configurations for which subjective pilot ratings were obtained. Specific attention is given to the development of the simulator program and procedures so as to yield objective and subjective performance data useful for a critical evaluation of the analytical method.

Moul, M. T.↗

Effects of control saturation on the command response of statically unstable aircraft

Hanson and Stengel (1981) have described the effects of saturating controls on the initial-condition response of statically unstable aircraft. In an analysis of the stability augmentation system, consideration was given to maximizing the region of stable response. The present investigation is concerned with an extension of the control saturation analysis to the problem of command response, taking into account the main problem of control design for satisfactory flying qualities (as perceived by the pilot). A model for examining the effects of control saturation on longitudinal stability and command response is developed and applied to an aircraft with a static instability. Three parameters prescribing longitudinal flying qualities are examined with respect to their ability to identify proper flying qualities in the presence of control saturation. The presented analysis provides also satisfactory guidelines for establishing command saturation/stability boundaries.

Hanson, G. D.↗

Origin of the Greenland Ice Sheet

A climate model resolving the seasonal cycle and the two horizontal dimensions was developed and applied to several problems of current interest. Models of this type are useful when for various reasons a general circulation model experiment is not warranted or not feasible. For example, in cases where the signal to natural variability is small it may be advantageous to first consider such a statistical dynamical model because extremely long runs may be necessary in the application. In this case the simpler statistical dynamical model serves as a pilot study device. The model developed is a thermodynamic model whose solution yields the equilibrium seasonal cycle for the surface temperature field over the globe. The model is essentially a statement of the conservation of heat energy for individual columns of the earth atmosphere system. Various terms such as the infrared radiation flux to space are parameterized with earth radiation budget data from satellites such as Nimbus 6. The primary agent modulating the seasonal cycle amplitude is the heat capacity per unit area which is a strong function of surface type -- ocean surface can store 60 times more heat per unit time than land. By adjusting its few empirical parameters the model can be brought into remarkable agreement with the observed seasonal cycle. The model is then very useful for looking at the dependence of the seasonal cycle of the temperature on such externally defined variables as the Earth's orbital elements (eccentricity, tilt, precession of equinoxes) or the configuration of land-sea geography which can be changed by continental drift.

North, G. R.↗

Flight test of a displacement sidearm controller

A six-axis displacement-stick sidearm controller was developed to enable single-handed control of remote manipulator operations in space. With a working model available, piloted evaluation became possible in a fly-by-computer variable-stability research aircraft, originally a Bell 205 helicopter. The original mechanization was limited to three rotational axes and a linear one, analogous to the collective stick. A newly designed short stickgrip was mounted and the spring force pattern adjusted to suit the helicopter flight control environment. A standard set of test maneuvers was flown by four experimental pilots with conventional helicopter flight controls and with sidearm controllers equipped with two different handgrips. Existing data from flight tests with an isometric-stick controller were added to complete the comparison. The displacement controller consistently achieved a rating of 3.0 to 3.5 on the Cooper-Harper scale, on par with the conventional controls. The same basic controller design was tested in spacecraft and remote manipulator simulations with very promising results. In each application operator/system integration was rapid and positive. The results demonstrate feasibility and support the design philosphy of using deflection as well as force to generate proprioceptive feedback.

Lippay, A. L.↗

A simulation evaluation of a pilot interface with an automatic terminal approach system

The pilot-machine interface with cockpit automation is a critical factor in achieving the benefits of automation and reducing pilot blunders. To improve this interface, an automatic terminal approach system (ATAS) was conceived that can automatically fly a published instrument approach by using stored instrument approach data to automatically tune airplane radios and control an airplane autopilot and autothrottle. The emphasis in the ATAS concept is a reduction in pilot blunders and work load by improving the pilot-automation interface. A research prototype of an ATAS was developed and installed in the Langley General Aviation Simulator. A piloted simulation study of the ATAS concept showed fewer pilot blunders, but no significant change in work load, when compared with a baseline heading-select autopilot mode. With the baseline autopilot, pilot blunders tended to involve loss of navigational situational awareness or instrument misinterpretation. With the ATAS, pilot blunders tended to involve a lack of awareness of the current ATAS mode state or deficiencies in the pilots' mental model of how the system operated. The ATAS display provided adequate approach status data to maintain situational awareness.

Hinton, David A.↗

Design and construction of a remote piloted flying wing

Currently, there is a need for a high-speed, high-lift civilian transport. Although unconventional, a flying wing could fly at speeds in excess of Mach 2 and still retain the capacity of a 747. The design of the flying wing is inherently unstable since it lacks a fuselage and a horizontal tail. The project goal was to design, construct, fly, and test a remote-piloted scale model flying wing. The project was completed as part of the NASA/USRA Advanced Aeronautics Design Program. These unique restrictions required us to implement several fundamental design changes from last year's Elang configuration including wing sweepback and wingtip endplates. Unique features such as a single ducted fan engine, composite structural materials, and an electrostatic stability system were incorporated. The result is the Banshee '94. Our efforts will aid future projects in design and construction techniques so that a viable flying wing can become an integral part of the aviation industry.

Costa, Alfred J.↗

Measurement of human pilot dynamic characteristics in flight simulation

Fast Fourier Transform (FFT) and Least Square Error (LSE) estimation techniques were applied to the problem of identifying pilot-vehicle dynamic characteristics in flight simulation. A brief investigation of the effects of noise, input bandwidth and system delay upon the FFT and LSE techniques was undertaken using synthetic data. Data from a piloted simulation conducted at NASA Ames Research Center was then analyzed. The simulation was performed in the NASA Ames Research Center Variable Stability CH-47B helicopter operating in fixed-basis simulator mode. The piloting task consisted of maintaining the simulated vehicle over a moving hover pad whose motion was described by a random-appearing sum of sinusoids. The two test subjects used a head-down, color cathode ray tube (CRT) display for guidance and control information. Test configurations differed in the number of axes being controlled by the pilot (longitudinal only versus longitudinal and lateral), and in the presence or absence of an important display indicator called an 'acceleration ball'. A number of different pilot-vehicle transfer functions were measured, and where appropriate, qualitatively compared with theoretical pilot- vehicle models. Some indirect evidence suggesting pursuit behavior on the part of the test subjects is discussed.

Reedy, James T.↗

Analysis of Autopilot Behavior

Aviation and cognitive science researchers have identified situations in which the pilot's expectations for behavior of autopilot avionics are not matched by the actual behavior of the avionics. These "automation surprises" have been attributed to differences between the pilot's model of the behavior of the avionics and the actual behavior encoded in the avionics software. A formal technique is described for the analysis and measurement of the behavior of the cruise pitch modes of a modern Autopilot. The analysis characterizes the behavior of the Autopilot as situation-action rules. The behavior of the cruise pitch mode logic for a contemporary modern Autopilot was found to include 177 rules, including Level Change (23), Vertical Speed (16), Altitude Capture (50), and Altitude Hold (88). These rules are determined based on the values of 62 inputs. Analysis of the rule-based model also shed light on the factors cited in the literature as contributors to "automation surprises."

Sherry, Lance↗

Characterization of Pilot Technique

Skilled pilots often use pulse control when controlling higher order (i.e. acceleration-command) vehicle dynamics. Pulsing does not produce a stick response that resembles what the human Crossover Model predicts. The Crossover Model (CM) assumes the pilot provides compensation necessary (lead or lag) such that the suite of display-human-vehicle approximates an integrator in the region of crossover frequency. However, it is shown that the CM does appear to drive the pilots pulsing behavior in a very predictable manner. Roughly speaking, the pilot generates pulses such that the area under the pulse (pulse amplitude multiplied by pulse width) is approximately equal to area under the hypothetical CM output. This can allow a pilot to employ constant amplitude pulsing so that only the pulse duration (width) is modulated a drastic simplification over the demands of continuous tracking. A pilot pulse model is developed, with which the parameters of the pilots internally-generated CM can be computed in real time for pilot monitoring and display compensation. It is also demonstrated that pursuit tracking may be activated when pulse control is employed.

rotorcraft↗

V/STOL tilt rotor aircraft study. Volume 9: Piloted simulator evaluation of the Boeing Vertol model 222 tilt rotor aircraft

The results of a real time piloted simulation to investigate the handling qualities and performance of a tilting rotor aircraft design are presented. The aerodynamic configuration of the aircraft is described. The procedures for conducting the simulator evaluation are reported. Pilot comments of the aircraft handling qualities under various simulated flight conditions are included. The time histories of selected pilot maneuvers are shown.

Rosenstein, H.↗

Nonlinear Aerodynamic Modeling From Flight Data Using Advanced Piloted Maneuvers and Fuzzy Logic

Results of the Aeronautics Research Mission Directorate Seedling Project Phase I research project entitled "Nonlinear Aerodynamics Modeling using Fuzzy Logic" are presented. Efficient and rapid flight test capabilities were developed for estimating highly nonlinear models of airplane aerodynamics over a large flight envelope. Results showed that the flight maneuvers developed, used in conjunction with the fuzzy-logic system identification algorithms, produced very good model fits of the data, with no model structure inputs required, for flight conditions ranging from cruise to departure and spin conditions.

Brandon, Jay M.↗

A quasi-Newton procedure for identifying pilot-related parameters of the optimal control model

The development and application of a quasi-Newton gradient search procedure for identifying independent pilot related parameters of the optimal control model for pilot/vehicle systems is reported. A sensitivity analysis procedure which determines whether a given model parameter is required to match a specific experimental result, and which experimentally induced parameter changes are required to account for behavioral and performance differences, is described. Application of the identification scheme to training effects in a manual control task is described.

Levison, W. H.↗

The role of manipulator characteristics in selecting the ideal effective vehicle

A structural model of the human pilot is introduced and discussed. The model is used to provide a rationale for certain nonlinear pilot control behavior such as stick pulsing and serves as a framework for studying aspects of motor skill development. In light of the theoretical background provided by the model, some past empirical pilot response phenomena are analyzed and shown to be attributable to manipulator or control stick characteristics. In particular, some recent problems associated with pilot/vehicle performance in glideslope tracking in short takeoff and landing (STOL) aircraft are analyzed. The apparent contribution of the cockpit manipulator (throttle) characteristics to these problems are outlined and a solution proposed and evaluated in both simulation and flight test.

Hess, R. A.↗

Digital Biosecurity Pilot Project

Security models for the bioeconomy have largely been developed on risk profiles borrowed from the financial industry and, in some cases, industrial control systems. The bioeconomy, however, has unique characteristics that require domain-specific knowledge of the risks to environmental, health and economic impact from directly targeted attacks. Key questions need to be assessed and answered for any facility engaged in bioproduction. These include: how much technical information must the attacker possess in order to target a specific process or facility? Which processes cause the largest economic impact if disrupted? Can an attacker lead companies down the wrong path of research, leading to irrecoverable losses of time, resources and capital? Can attackers disrupt venture capital strategies and affect financial returns? What are the resources required to attack key workflows, and subsequently what is the cost of defense? What strategies are effective against such attackers, and what are their cost? Can government provide an active role in assurance of material, process and results for critical bioeconomic infrastructure?

59 BASIC BIOLOGICAL SCIENCES↗

A3I visibility modeling project

The Army-NASA Aircrew Aircraft Integration program is supporting a joint project to build a visibility computer-aided design (CAD) tool. CAD has become an essential tool in modern engineering applications. CAD tools are used to create engineering drawings and to evaluate potential designs before they are physically realized. The visibility CAD tool will provide the design engineer with a tool to aid in the location and specification of windows, displays, and control in crewstations. In an aircraft cockpit the location of instruments and the emissive and reflective characteristics of the surfaces must be determined to assure adequate aircrew performance. The visibility CAD tool will allow the designer to ask and answer many of these questions in the context of a three-dimensional graphical representation of the cockpit. The graphic representation of the cockpit is a geometrically valid model of the cockpit design. A graphic model of a pilot, called the pilot manikin, can be placed naturalistically in the cockpit model. The visibility tool has the capability of mapping the cockpit surfaces and other objects modeled in this graphic design space onto the simulated pilot's retinas for a given visual fixation.

Larimer, James↗

Unmanned Aircraft Systems Minimum Operations Performance Standards End-to-End Verification and Validation (E2-V2) Simulation

As Unmanned Aircraft Systems (UAS) make their way to mainstream aviation operations within the National Airspace System (NAS), research efforts are underway to develop a safe and effective environment for their integration into the NAS. Detect and Avoid (DAA) systems are required to account for the lack of "eyes in the sky" due to having no human on-board the aircraft. The current NAS relies on pilot's vigilance and judgement to remain Well Clear (CFR 14 91.113) of other aircraft. RTCA SC-228 has defined DAA Well Clear (DAAWC) to provide a quantified Well Clear volume to allow systems to be designed and measured against. Extended research efforts have been conducted to understand and quantify system requirements needed to support a UAS pilot's ability to remain well clear of other aircraft. The efforts have included developing and testing sensor, algorithm, alerting, and display requirements. More recently, sensor uncertainty and uncertainty mitigation strategies have been evaluated. This paper discusses results and lessons learned from an End-to-End Verification and Validation (E2-V2) simulation study of a DAA system representative of RTCA SC-228's proposed Phase I DAA Minimum Operational Performance Standards (MOPS). NASA Langley Research Center (LaRC) was called upon to develop a system that evaluates a specific set of encounters, in a variety of geometries, with end-to-end DAA functionality including the use of sensor and tracker models, a sensor uncertainty mitigation model, DAA algorithmic guidance in both vertical and horizontal maneuvering, and a pilot model which maneuvers the ownship aircraft to remain well clear from intruder aircraft, having received collective input from the previous modules of the system. LaRC developed a functioning batch simulation and added a sensor/tracker model from the Federal Aviation Administration (FAA) William J. Hughes Technical Center, an in-house developed sensor uncertainty mitigation strategy, and implemented a pilot model similar to one from the Massachusetts Institute of Technology's Lincoln Laboratory (MIT/LL). The resulting simulation provides the following key parameters, among others, to evaluate the effectiveness of the MOPS DAA system: severity of loss of well clear (SLoWC), alert scoring, and number of increasing alerts (alert jitter). The technique, results, and lessons learned from a detailed examination of DAA system performance over specific test vectors and encounter cases during the simulation experiment will be presented in this paper.

Ghatas, Rania W.↗

Helicopter simulation validation using flight data

A joint NASA/Army effort to perform a systematic ground-based piloted simulation validation assessment is described. The best available mathematical model for the subject helicopter (UH-60A Black Hawk) was programmed for real-time operation. Flight data were obtained to validate the math model, and to develop models for the pilot control strategy while performing mission-type tasks. The validated math model is to be combined with motion and visual systems to perform ground based simulation. Comparisons of the control strategy obtained in flight with that obtained on the simulator are to be used as the basis for assessing the fidelity of the results obtained in the simulator.

Key, D. L.↗