Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Combining direct ink writing with reactive melt infiltration to create architectured thermoelectric legs

Here, we present a new additive-reactive synthesis method where inks – cast into molds or 3D-additively extruded into architectured shapes – are reacted into intermetallic thermoelectric compounds. The new method, as demonstrated for equiatomic TiNiSn, combines: (i) extrusion printing (or casting) of inks containing Ni and Ti powders, (ii) debinding and reactive sintering to form a porous NiTi network, (iii) network infiltration with liquid Sn and subsequent reaction to synthesize the TiNiSn phase. Thin plates, created through this method, show high phase purity and low residual porosity. A thermoelectric figure of merit zT = 0.47 ± 0.05 is achieved at 800 K, within the broad range of values (zT= 0.3–1.0) reported for TiNiSn created via traditional powder hot-pressing methods. Layered TiNiSn microlattices – after 3D ink-extrusion printing and infiltration – exhibit high relative densities and minimal undesirable secondary phase content, with a Seebeck coefficient on par with the ink-cast TiNiSn plates, demonstrating that thermoelectric legs with far-ranging architectural freedom can be created additively with this novel reactive manufacturing method. Numerous other thermoelectric (and other) compounds, currently limited to basic geometries due to brittleness, are amenable to this new method based on a sequence of reactive sintering/infiltration of cast or ink-extruded precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tailoring Microbial Fitness Through Computational Steering and CRISPRi-Driven Robustness Regulation

The widespread application of genetically modified microorganisms (GMMs) across diverse sectors underscores the pressing need for robust strategies to mitigate the risks associated with their potential uncontrolled escape. This study merges computational modeling with CRISPR interference (CRISPRi) to refine GMM metabolic robustness. Utilizing ensemble modeling, we achieved high-throughput in silico screening for enzymatic targets susceptible to expression alterations. Translating these insights, we developed functional CRISPRi, boosting fitness control via multiplexed gene knockdown. Our method, enhanced by an insulator-improved gRNA structure and an off-switch circuit controlling a compact Cas12m, resulted in rationally engineered strains with escape frequencies below National Institutes of Health standards. The effectiveness of this approach was confirmed under various conditions, showcasing its ability for secure GMM management. This research underscores the resilience of microbial metabolism, strategically modifying key nodes to halt growth without provoking significant resistance, thereby enabling more reliable and precise GMM control. A record of this paper's transparent peer review process is included in the supplemental information.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Zirconium-diboride silicon-carbide composites: A review

Zirconium diboride (ZrB 2 ) and silicon carbide (SiC) composites have long been of interest since it was observed that ZrB 2 improved the thermal shock resistance of SiC. However, processing of these materials can be difficult due to high and different sintering temperatures and differences in the thermodynamic stability of each material. ZrB 2 –SiC composites have been processed in a variety of ways including hot-pressing, spark-plasma sintering, reactive melt infiltration, pack cementation, chemical vapor deposition, chemical vapor infiltration, stereolithography, direct ink writing, selective laser sintering, electron beam melting, and binder jet additive manufacturing. Each manufacturing method has its own pros and cons. This review serves to summarize more than 60 years of research and provide a coherent resource for the variety of methods and advancements in development of ZrB 2 –SiC composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis of nanograined zirconium diboride microsphere powder feedstock via emulsification of suspensions

Ceramic nanograined materials have desirable characteristics compared to their macroparticle counterparts but are rarely used in industrial applications due to issues with poor handleability and health hazards. Due to interparticle forces that become more dominant as the particle size decreases, it is difficult to use nanomaterials to fill dies, spread on surfaces, or flow through hoppers found in various manufacturing processes. In this work, we report a scalable gelcasting solution and unique emulsification process to create microspheres composed of nanoscale powders to enhance the flowability and handleability of nanomaterials. The gelcasting solution and emulsification process can be used with any nanoparticle composition that can be suspended in a liquid phase. This paper reports the effects of various parameters on zirconium diboride microsphere formation, such as surfactant content and mixing conditions. The microspheres maintain the nano-scale characteristics of the powder but improve its flowability by using cross-linked polyvinyl alcohol to combine irregularly shaped zirconium diboride nanoparticles with a particle diameter of 60 nm into larger spherical particles with a d 50 ~25 μm. This hierarchical feedstock engineering design combine the positive characteristics of materials across both length scales and improve the flowability of the feedstock from a Hausner Ratio of 1.56 to 1.19. The materials produced using this technique can be used in thermal plasma spray, die filling for hot pressing or spark plasma sintering, and binder jet printing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Physicochemical properties of digital light processing 3D-Printed alumina and mullite ceramics

Alumina ceramics fabricated using conventional techniques such as uniaxial pressing or injection molding are popular due to their low density, excellent insulation, and mechanical properties. However, these methods often limit the fabrication of complex geometries with high dimensional accuracy due to tooling constraints and limited design freedom. To overcome these limitations, this study employed Digital Light Processing (DLP) additive manufacturing (AM), which enables the production of precise structures. In addition, the optimization of sintering parameters to enhance the densification and performance of alumina and mullite ceramics was investigated, with a specific focus on how varying sintering temperatures and hold times affect part shrinkage, geometric accuracy, and material integrity. Flexural strength of both alumina and mullite specimens was clearly influenced by the way the layers was stacked. When layers were arranged across the direction of the applied load (Z = 4; XZ), the strength was higher than when they were stacked along the same direction as the load (Z = 3; XY). Weibull analysis based on these results showed high modulus values across all samples, indicating good reliability in the flexural strength measurements. This reliability, combined with the clear influence of sintering parameters, highlights how processing conditions effect the material properties and mechanical performance of parts produced through DLP additive manufacturing. In conclusion, these findings open new avenues for ceramic AM across various applications, enhancing the potential for innovation in fields such as aerospace, biomedical engineering, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High pressure experimental investigation of clinopyroxene dissolution in a K-basaltic melt

Dissolution of clinopyroxene (cpx) in a K-basaltic melt from the Campi Flegrei Volcanic District (Italy) has been investigated through dissolution and dissolution-crystallization experiments at pressure of 0.8 GPa, superliquidus temperature of 1350 °C, and dwell times between 0.5 and 1 h. The obtained dissolution rates range from 7.9·10 –6 cm s –1 to 6.1·10 –6 cm s –1 as a function of dwell time. In the dissolution-crystallization experiment (1300 °C; 0.8 GPa; 2 h), the formation of overgrowth rims accompanied by new cpx crystals suggests that the injection of recharge magmas in basaltic reservoir may lead to inverse or oscillatory zonation. The interaction between cpx and K-basaltic melt at ~1570 °C was studied by in situ radiography using synchrotron radiation combined with the Paris-Edinburgh press. Here, this resulted in cpx resorption to occur depending on the temperature conditions with respect to the liquidus temperature of the cpx (T cpxL ). The calculated cpx dissolution rates are ~5·10 –3 cm s –1 at T ≤ T cpxL and ~ 3·10 –2 cm s –1 at T ≥ T cpxL . The role of crystal dissolution in the estimation of magma residence times has been also tested for a natural magmatic system by interpolating the dissolution rates (~10 –5 –10 –6 cm s –1 ) with the textural data of cpx phenocrysts from the Agnano-Monte Spina pyroclastic deposit at Campi Flegrei caldera (Campanian region, Italy). Results from calculations indicate that the time required for partial or complete resorption of phenocrysts varies from ~0.5 to ~40 h, and that the effect of crystal dissolution may be relevant to estimate magma residence times whether significant dissolution occurs during magma mixing processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Chemistry imaging and distribution analysis of rare earth elements in coal using LIBS and LA-ICP-MS instruments

Currently, demand for rare earth elements (REEs) increased significantly. Coal is actively evaluated as potential economic sources for extraction of REEs. Here, in this work, laser-induced breakdown spectroscopy (LIBS) was evaluated for rapid estimation of REEs content and their distribution in the natural coal samples. The results were compared with similar laser ablation–inductively coupled plasma–mass spectrometry (LA-ICP-MS) measurements. Thirteen coal samples (nine standard samples and five natural samples) were used in this study. Powder samples were pressed into pellets while coal chunks were directly ablated for data recording. Pellets of the powder standard samples were used to optimize the data acquisition system and then data recorded with this optimized system was used to identify the proper data acquisition and analysis models. After establishing the proper data acquisition system and analysis model using the standard samples, natural coal samples in powder form and their chunks were utilized to record LIBS and LA-ICP-MS spectra. Multivariate calibration models were developed using four of the natural samples, which were evaluated by predicting the REE content in the fifth sample. Principal component analysis was performed on the LIBS data obtained from the natural samples and it classified all the samples with high accuracy. Two-dimensional (2D) elemental mapping on coal chunk samples was also performed using both LIBS and LA-ICP-MS to study the distribution of REEs in the samples. The resulting elemental images and their correlations can be used to infer mineral distributions.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Investigation of the notch sensitivity of tailorable long fiber discontinuous prepreg composite laminates

Tailorable discontinuous fiber composite laminates provide relative formability beyond that of continuous fiber laminates, while achieving improved mechanical performance over comparable stochastic systems. Here, in this work, the notch sensitivity of engineered prepreg platelet molded composite (PPMC) laminates is investigated using the open-hole tension (OHT) test and compared to available data for stochastic PPMCs and continuous fiber laminates made with the same material. The press-formed thermoplastic composites (AS4/PEKK) were molded with a quasi-isotropic stacking sequence. The discontinuous PPMC laminate was found to be notch insensitive with OHT strengths ranging from 145.4 MPa (CV $=$ 7%) for d/w $=$ 0.5 to 229.3 MPa (CV $=$ 9%) for d/w $=$ 0.25. The highly ordered meso-structure of the engineered PPMC laminate yields comparatively excellent mechanical properties for relatively thin laminates in contrast to stochastic systems. Both net- and gross-section failures were observed for d/w $=$ 0.25, which suggests that the engineered PPMC laminates studied here maintain a degree of inherent, internal stress concentrations that compete with those caused by geometric features such as a circular hole. Computational simulations of the OHT tests with explicitly represented platelets were found to be in good agreement with experimental measurements. The progressive failure analysis was used to conduct a numerical investigation of the stacking sequence and platelet meso-morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Damage progression and failure of SiC/SiC composite tubes under hard-contact radial expansion

The response of silicon carbide (SiC) fiber-reinforced SiC matrix (SiC/SiC) composite cladding to mechanical interaction with fissile fuel is a knowledge gap that must be overcome to design and assess SiC-based cladding systems for advanced nuclear applications. This study developed the relevant mechanical testing capability and identified the failure behavior and the critical microstructural features and processing defects. Sections of SiC composite tube were subjected to a modified expansion-due-to-compression (EDC) test in an X-ray computed tomography microscope: a polyurethane plug pressed surrogate Al 2 O 3 into the inner walls of the SiC/SiC composite tubes to achieve hard contact. A pure EDC test with just a polyurethane plug was also performed as a reference. Through the use of displacement fields, digital volume correlation revealed inhomogeneous deformation fields in the tubes, even for pure EDC, which was related to the inherent defects in the structure. Deep learning–aided segmentation and systematic data analysis revealed that the presence of inhomogeneous deformation applied by the hard contact was exaggerated by the presence of inner surface imperfections left behind from the matrix densification process. In conclusion, the findings provide insights into the applications, highlighting the necessity for improvements in inner surface roughness and the incorporation of localized contacts in pellet–cladding mechanical interaction computational models.

Composites↗
DOE OSTI2020

Pollution to products: recycling of ‘above ground’ carbon by gas fermentation

Climate crisis and rapid population growth are posing some of the most pressing challenges to mankind and have intensified the need for the deployment of carbon recycling and carbon capture and utilization (CCU) technologies. Gas fermentation offers a solution using carbon-fixing chemolithoautotrophic microorganisms. After a decade of scale up, the technology has recently been commercialized with the first plant operating successfully since 2018 and additional units under construction. Gas fermentation offers unique feedstock and product flexibility when compared to other available gas-to-liquid technologies. Advancements in process technology and synthetic biology enable a broad range of feedstocks including emissions from industry or syngas generated from any biomass resource to be converted into a wide range of molecules realizing a circular economy.

09 BIOMASS FUELS↗
DOE OSTI2020

Corrosion of Al 2 O 3 /Cr and Ti 2 O 3 /Cr composites in flowing air and CO 2 at 750°C

Hot-pressed Al 2 O 3 /Cr and Ti 2 O 3 /Cr composites were exposed to synthetic air or CO 2 at 750 °C. The Al 2 O 3 /Cr composites formed external Cr 2 O 3 scales, and exhibited slow parabolic oxidation kinetics, in both gases. The Cr 2 O 3 scales formed in CO 2 possessed finer grains, and thickened at a faster rate, than Cr 2 O 3 scales formed in air. The Ti 2 O 3 /Cr composites formed thick external TiO 2 scales with internal oxidation zones that also contained Cr 2 O 3 scales on subsurface Cr grains. After 20 h at 750 °C, the Ti 2 O 3 /Cr composites exhibited parabolic oxidation kinetics in both gases, although the oxidation rates were significantly higher than for the Al 2 O 3 /Cr composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A novel electro-hydraulic unit design based on a shaftless integration of an internal gear machine and a permanent magnet electric machine

In recent years, increasingly stringent emission regulations have spurred an electrification trend in off-highway vehicle technology. To address challenges such as the high cost of power electronics components, limited battery capacity, and the substantial modifications required for the vehicles, there is a pressing need to develop high-speed, cost-effective, compact, and efficient electro-hydraulic units capable of powering vehicle functions. In response to these demands, this paper introduces an innovative morphology for an electro-hydraulic unit and outlines the integration method for a crescent-type internal gear machine with a permanent magnet synchronous electric machine. The proposed morphology aims to minimize component count through a shaftless solution while incorporating a cooling system that utilizes the same working fluid as the hydraulic machine. The design approach utilizes a genetic algorithm optimization process to maximize overall energy efficiency and compactness. Insights gained from the optimization results shed light on the relationship between key design parameters and unit performance, enhancing the understanding of this electro-hydraulic unit. A prototype of the unit was manufactured and tested, demonstrating a volumetric efficiency ranging from 81 % to 97 % at a maximum rotational velocity of the pinion of 6000 rpm. Finally, these results validate both the morphology and the design approach, indicating the feasibility of designing compact electro-hydraulic units that leverage hydraulic machines with higher maximum rotational velocities than commercially available counterparts as a mean to enhance efficiency and compactness.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Advanced strategies for the development of porous carbon as a Li host/current collector for lithium metal batteries

Lithium metal is considered a promising anode material for high-energy-density rechargeable batteries because of its high specific theoretical capacity (3860 mAh g -1 , low mass density (0.534 g cm -3 ), and low electrochemical redox potential (-3.04 V vs. the standard hydrogen electrode). However, the high reactivity of Li with the electrolyte leads to the formation of an unstable solid electrolyte interphase (SEI) and continuous side reactions. Also, the non-uniform lithium-ion flux and infinite volume expansion of Li metal cause the growth of Li dendrites. These pose significant safety challenges and cause rapid capacity fading of the lithium metal batteries (LiMBs). To resolve these issues, a low-cost, easily processed, lightweight, high-performance carbon-based porous matrix is considered promising to host Li metal deposition. The three-dimensional (3D) porous nano/microstructured carbon provides sufficient space for Li accommodation during Li plating, buffers the volume changes during Li plating/stripping, and lowers the effective current density contributing to dendrite-free Li deposition. Besides, the outstanding electrochemical and mechanical stability, flexibility and the high electronic conductivity enable the nano/microstructured carbon to serve as both Li host and current collector. The development of 3D carbon/Li composite by mechanical roll-press techniques not only eliminates the complex and risky procedure of making carbon/Li composite based on Li plating or molten Li infusion but also stabilizes the capacity at higher Li plating/stripping rates. Recently, there is an advancement in the lithiophilic decorations of 3D structure to introduce sufficient nucleation sites and the development of artificial SEI on top of the 3D matrix to suppress Li dendrite formation. Such 3D structural modifications create a uniform electric field, lower the Li nucleation overpotential, provide strong mechanical and chemical stability, and stabilize the interface thereby inhibiting the degradation of lithium and the electrolyte. Here we summarize the research progress on porous carbon/Li composites in terms of materials type, structure, fabrication technique, their electrochemical battery performance, and identify the critical challenges that need to be addressed for high-energy-density practical LiMBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Towards intelligent emergency control for large-scale power systems: Convergence of learning, physics, computing and control

Here, this paper has delved into the pressing need for intelligent emergency control in large-scale power systems, which are experiencing significant transformations and are operating closer to their limits with more uncertainties. Learning-based control methods are promising and have shown effectiveness for intelligent power system control. However, when they are applied to large-scale power systems, there are multifaceted challenges such as scalability, adaptiveness, and security posed by the complex power system landscape, which demand comprehensive solutions. The paper first proposes and instantiates a convergence framework for integrating power systems physics, machine learning, advanced computing, and grid control to realize intelligent grid control at a large scale. Our developed methods and platform based on the convergence framework have been applied to a large (more than 3000 buses) Texas power system, and tested with 56 000 scenarios. Our work achieved a 26% reduction in load shedding on average and outperformed existing rule-based control in 99.7% of the test scenarios. The results demonstrated the potential of the proposed convergence framework and DRL-based intelligent control for the future grid.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Impact of non-irrigation on 1G and 2G bioethanol potential of oilcane feedstock: A field to fuel pipeline study

This study evaluates the bioethanol potential in response to irrigation (IR) and non-irrigation (NIR) of oilcane (OC) during a seasonal drought prior harvest. The juice was extracted through mechanical pressing of stems and fermented by Ethanol Red® yeast to produce first-generation bioethanol. Hydrothermal pretreatment followed by enzymatic hydrolysis of bagasse was performed to produce monomeric sugars from structural carbohydrates. The hydrolysates were fermented with engineered yeast for second-generation bioethanol production. The irrigated oilcane juice (276.3 ± 8.9 g/L) constitutes higher sugar concentrations than non-irrigated oilcane juice (236.5 ± 2.2 g/L). The enzymatic hydrolysis of IR-OC and NIR-OC pretreated bagasse yielded similar concentrations of 247.5 ± 2.22 and 249.7 ± 4.98 g/L fermentable sugars. Industry-relevant bioethanol titers of ≥99 g/L and ≥75 g/L were achieved from juice and hydrolysates, respectively. Therefore, the non-irrigation regime did not impact the 1G and 2G bioethanol titers. However, the overall bioethanol yield can be lower due to the reduction of stem yield (8 %) per hectare.

09 BIOMASS FUELS↗
DOE OSTI2021

Warming promotes the use of organic matter as an electron acceptor in a peatland

Peatlands store approximately one-half of terrestrial soil organic carbon (C) and the future of this C in the face of ongoing global change remains a key question in global biogeochemistry. Particularly pressing is the need to understand if this C will remain in peatland soils or be returned to the atmosphere as the potent greenhouse gas methane (CH 4 ) in response to warming. Past work has demonstrated that the microbial reduction of organic matter (OM) as an alternative terminal electron acceptor (TEA) under anaerobic conditions can suppress CH 4 production and is a key mechanistic control of peatland CH 4 dynamics. Here we show that warming directly enhances rates of potential OM reduction in peatland soils, enhancing acetate availability and allowing for a faster onset of CH 4 production. Finally, using soils collected from the ecosystem-scale Spruce and Peatland Responses Under Changing Environments (SPRUCE) experiment, we also show that while there were no indirect effects of 2 years of soil warming on potential OM reduction through changes in soil quality, warming-mediated lowering of the water table increased the volume of oxidized OM which will suppress CH 4 production following rewetting events.

54 ENVIRONMENTAL SCIENCES↗