Search NASA⌕ Search

SEARCH · Search NASA

Results for “protection system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Comparison of thermal protection systems for a space shuttle booster and orbiter.

Selection of the most appropriate thermal protection system design approaches requires evaluation of alternate concepts. Such an evaluation was conducted for a representative booster and orbiter configurations. TPS concept examined for the booster included heat sink, metallic reradiative, reusable surface insulation, and surface cooled types. For the orbiter, emphasis was placed on metallic reradiative and reusable surface insulation concepts with uncooled, phase change material cooled, and water-cooled substructures. Three insulation materials of different densities were examined for the orbiter reradiative TPS to identify the weight sensitivity of various substructural design approaches to this variable.

Anthony, F. M.↗
NASA NTRS1981

Icing tunnel tests of a glycol-exuding porous leading edge ice protection system on a general aviation airfoil

A glycol-exuding porous leading edge ice protection system was tested. Results show that the system is very effective in preventing ice accretion (anti-ice mode) or removing ice from an airfoil. Minimum glycol flow rates required for anti-icing are a function of velocity, liquid water content in the air, ambient temperature, and droplet size. Large ice caps were removed in only a few minutes using anti-ice flow rates. It was found that the shed time is a function of the type of ice, size of the ice cap, angle of attack, and glycol flow rate. Wake survey measurements show that there is no significant drag penalty for the installation or operation of the system tested.

Kohlman, D. L.↗
NASA NTRS1983

Analysis of gap heating due to stepped tiles in the shuttle thermal protection system

Analytical methods used to investigate entry gap heating in the Shuttle orbiter thermal protection system are described. Analytical results are given for a fuselage lower-surface location and a wing lower-surface location. These are locations where excessive gap heating occurred on the first flight of the Shuttle. The results of a study to determine the effectiveness of a half-height ceramic fiber gap filler in preventing hot-gas flow in the tile gaps are also given.

Petley, D. H.↗
NASA NTRS1983

The Shuttle Orbiter thermal protection system materials, designs, and flight performance overview

The design requirements for the Orbiter thermal protection system (TPS), the various TPS materials that are used, the different design approaches associated with each of the materials, and the performance experienced during the flight test program are described. The first five flights of the Orbiter Columbia have provided the necessary data to verify the TPS thermal performance, structural integrity, and reusability. The flight performance characteristics of each TPS material are discussed. This discussion is based on postflight inspections and postflight interpretation of the flight instrumentation data. The flights to date indicate that the thermal and structural design requirements for the Orbiter TPS have been met and that the overall performance has been outstanding.

Dotts, R. L.↗
NASA NTRS1985

Impacts of Space Shuttle thermal protection system tile on F-15 aircraft vertical tile

Impacts of the space shuttle thermal protection system (TPS) tile on the leading edge and the side of the vertical tail of the F-15 aircraft were analyzed under different TPS tile orientations. The TPS tile-breaking tests were conducted to simulate the TPS tile impacts. It was found that the predicted tile impact forces compare fairly well with the tile-breaking forces, and the impact forces exerted on the F-15 aircraft vertical tail were relatively low because a very small fraction of the tile kinetic energy was dissipated in the impact, penetration, and fracture of the tile. It was also found that the oblique impact of the tile on the side of the F-15 aircraft vertical tail was unlikely to dent the tail surface.

Ko, W. L.↗
NASA NTRS1993

Toxicity study of dimethylethoxysilane (DMSES), the waterproofing agent for the Orbiter heat protective system

DMES, a volatile liquid, is used by NASA to waterproof the Orbiter thermal protective system. During waterproofing operations at the Oribter Processing Facility at KSC, workers could be exposed to DMES vapor. To assess the toxicity of DMES, acute and subchronic (2-week and 13-week) inhalation studies were conducted with rats. Studies were also conducted to assess the potential of DMES. Inhalation exposure concentrations ranged from 40 ppm to 4000 ppm. No mortality was observed during the studies. Exposures to 2100 ppm produced narcosis and ataxia. Post-exposure recovery from these CNS effects was rapid (less than 1 hr). These effects were concentration-dependent and relatively independent of exposure length. Exposure to 3000 ppm for 2 weeks (5 h/d, 5 d/wk) produced testicular toxicity. The 13-week study yielded similar results. Results from the genotoxicity assays (in vivo/in vitro unscheduled DNA synthesis in rat primary heptaocytes, chromosomal aberrations in rat bone marrow cells; reverse gene mutation in Salmonella typhimurium; and forward mutation in Chinese hamster culture cells) were negative. These studies indicated that DMES is mildly to moderately toxic but not a multagen.

Lam, Chiu-Wing↗
NASA NTRS1999

Design of Transpiration Cooled Thermal Protection Systems

This study explored three approaches for the utilization of transpiration cooling in thermal protection systems. One model uses an impermeable wall with boiling water heat transfer at the backface (Model I). A second model uses a permeable wall with a boiling water backface and additional heat transfer to the water vapor as it flows in channels toward the exposed surface (Model II). The third model also uses a permeable wall, but maintains a boiling condition at the exposed surface of the material (Model III). The governing equations for the models were developed in non-dimensional form and a comprehensive parametric investigation of the effects of the independent variables on the important dependent variables was performed. In addition, detailed analyses were performed for selected materials to evaluate the practical limitations of the results of the parametric study.

Callens, E. Eugene, Jr.↗
NASA NTRS2006

Fracture Toughness Evaluation of Space Shuttle External Tank Thermal Protection System Polyurethane Foam Insulation Materials

Experimental evaluation of the basic fracture properties of Thermal Protection System (TPS) polyurethane foam insulation materials was conducted to validate the methodology used in estimating critical defect sizes in TPS applications on the Space Shuttle External Fuel Tank. The polyurethane foam found on the External Tank (ET) is manufactured by mixing liquid constituents and allowing them to react and expand upwards - a process which creates component cells that are generally elongated in the foam rise direction and gives rise to mechanical anisotropy. Similarly, the application of successive foam layers to the ET produces cohesive foam interfaces (knitlines) which may lead to local variations in mechanical properties. This study reports the fracture toughness of BX-265, NCFI 24-124, and PDL-1034 closed-cell polyurethane foam as a function of ambient and cryogenic temperatures and knitline/cellular orientation at ambient pressure.

McGill, Preston↗
NASA NTRS2005

New Approach for Thermal Protection System of a Probe During Entry

One of the biggest challenges for any thermal protection system (TPS) of a probe is to provide a sufficient barrier for heat generated during descent in order to keep the temperature inside of the probe low enough to support operational temperature of equipment. Typically, such a goal is achieved by having the ceramic tiles and blankets like on the Space Shuttle, silicon based ablators, or metallic systems to cover the probe external surface. This paper discusses the development of an innovative technique for TPS of the probe. It is proposed to use a novel TPS which comprises thermal management of the entry vehicle. It includes: a) absorption of the heat during heat pick load by a Phase Change Material (PCM), b) separation of the compartment which contains PCM from the rest of the space vehicle by a gap with a high thermal resistance, c) maintaining temperature of the internal wall of s/c cabin temperature by transfer heat from the internal wall to the "cold" side of the vehicle and to reject heat into the space during the flight and on a ground, d) utilization of an advanced heat pipe, so called Loop Heat Pipe to transfer heat from the cabin internal wall to the cold side of the s/c and to reject the heat into environment outside of the vehicle. A Loop Heat Pipe is capable of transferring heat against gravity

Yendler, Boris↗
NASA NTRS2005

Nanostructured Thermal Protection Systems for Space Exploration Missions

Strong research and development programs in nanotechnology and Thermal Protection Systems (TPS) exist at NASA Ames. Conceptual studies have been undertaken to determine if new, nanostructured materials (composites of existing TPS materials and nanostructured composite fibers) could improve the performance of TPS. To this end, we have studied various candidate heatshields, some composed of existing TPS materials (with known material properties), to provide a baseline for comparison with others that are admixtures of such materials and a nanostructured material. In the latter case, some assumptions were made about the thermal conductivity and strength of the admixture, relative to the baseline TPS material. For the purposes of this study, we have made the conservative assumption that only a small fraction of the remarkable properties of carbon nanotubes (for example) will be realized in the material properties of the admixtures employing them. The heatshields studied included those for Sharp leading edges (appropriate to out-of-orbit entry and aero-maneuvering), probes, an out-of-orbit Apollo Command Module (as a surrogate for NASA's new Crew Exploration Vehicle [CEV]), a Mars Sample Return Vehicle and a large heat shield for Mars aerocapture missions. We report on these conceptual studies, which show that in some cases (not all), significant improvements in the TPS can be achieved through the use of nanostructured materials.

Arnold, J. O.↗
NASA NTRS2012

Calculating the Lightning Protection System Downconductors' Grounding Resistance at Launch Complex 39B, Kennedy Space Center

A new Lightning Protection System (LPS) was designed and built at Launch Complex 39B (LC39B), at the Kennedy Space Center (KSC), Florida, which consists of a catenary wire system (at a height of about 181 meters above ground level) supported by three insulators installed atop three towers in a triangular configuration. Nine downconductors (each about 250 meters long) are connected to the catenary wire system. Each downconductor is connected to a 7.62-meter-radius circular counterpoise conductor with six equally spaced, 6-meter-long vertical grounding rods. Grounding requirements at LC39B call for all underground and aboveground metallic piping, enclosures, raceways, and cable trays, within 7.62 meters of the counterpoise, to be bonded to the counterpoise, which results in a complex interconnected grounding system, given the many metallic piping, raceways, and cable trays that run in multiple directions around LC39B. The complexity of this grounding system makes the fall-of-potential method, which uses multiple metallic rods or stakes, unsuitable for measuring the grounding impedances of the downconductors. To calculate the grounding impedance of the downconductors, an Earth Ground Clamp (EGC) (a stakeless device for measuring grounding impedance) and an Alternative Transient Program (ATP) model of the LPS are used. The EGC is used to measure the loop impedance plus the grounding impedance of each downconductor, and the ATP model is used to calculate the loop impedance of each downconductor circuit. The grounding resistance of the downconductors is then calculated by subtracting the ATP calculated loop impedances from the EGC measurements.

Mata, Carlos T.↗
NASA NTRSDate not supplied

Minimally Intrusive Single-Chip Recession/Temperature Sensors for Spacecraft Thermal Protection Systems

We report the initial results of ongoing development of minimally intrusive, single-chip integrated capacitive recession/temperature sensors that would provide real-time monitoring of ablation recession of heatshield thermal protection systems (TPS) during spacecraft atmospheric entry. This work, which was performed using Phenolic Impregnated Carbon Ablator (PICA), is also to demonstrate the ease of sensor insertion during TPS manufacturing, thereby resulting in faster, low-cost, uniform sensor assembly, and spatial distribution, without compromising TPS structural integrity. Using oxy-acetylene flame at 500 W-cm-2 heat flux for 16 seconds, the average recession depth of 3.25 mm was obtained. Some measurement problems were encountered in this first attempt. However, the initial results obtained are in relatively good agreement with published data, and offer promise of future improvement based on lessons learned.

Recession↗
NASA NTRSDate not supplied

Mars 2020 Thermal Protection Systems (TPS)

This is a presentation for the Destination Space 2021 STEM activities leading up to and beyond the landing of the Perseverance Rover on Mars. This presentation will look at the thermal protection systems for the Mars entry vehicle by first showing the overall spacecraft, explaining a little about the mission, describing the harrowing entry and the reason why TPS is required. It will give a little introduction to the materials and how they behave. Finally a little background on the author is presented along with encouragement to look into engineering if students love math and science.

Mars 2020↗
NASA NTRS2010

Overview of the Orion Thermal Protection System

The Orion spacecraft is being developed as part of the Constellation Exploration Program and will serve as the United States crewed transportation system to the International Space Station after the retirement of the Space Shuttle in 2010 and as the eventual means to return U.S. astronauts to the Moon. Therefore, Orion is being designed for reentry missions from both low Earth orbit and from Lunar-return trajectories. This presentation will provide an overview of the development of the Orion TPS, a critical component in the development of the spacecraft. The thermal protection system (TPS) that protects the crew module from the extreme environments associated with Earth atmospheric reentry consists of a forward heatshield and an aft backshell. The requirements that drive the design of the TPS will be discussed, including several key requirements that establish a precedent for U.S. human-rated spacecraft. For the first time in U.S. human spaceflight, a vehicle s TPS is being designed with a specific, derived requirement for reliability. Also, due to the increased presence of spacecraft in Earth s orbit in recent decades, requirements for micro-meteoroid/orbital debris damage tolerance are also a driving requirement that has affected the selection of portions of the TPS. The efforts to select materials and to define a preliminary design for both the heatshield and the backshell will be described. This will include a discussion of the design challenges presented by the numerous penetrations on both the backshell and the heatshield. Finally, the verification and validation plan which is currently under development to certify the TPS for human-rated missions will be outlined. To support the execution of this plan, a ground test campaign for both thermal and structural performance is being designed. This test campaign will directly support thermal and thermal/structural analyses that also are fundamental to the certification effort.

Kowal, T. John↗
NASA NTRS2019

Effect of Phenolic Matrix Microcracking on the Structural Response of a 3-D Woven Thermal Protection System

The effect of microcracking in the phenolic matrix of a three-dimensional woven thermal protection system (TPS) and the resulting material stiffness reduction was studied via a comparison of finite element analysis results from a linear analysis and an iterative linear analysis. A TPS is necessary to protect space vehicles from the aerodynamic heating of planetary entry. The Heatshield for Extreme Entry Environment Technology (HEEET) project has developed a TPS for use in high heat-flux and pressure missions. The material is a dual-layer continuous dry weave, which is then infiltrated with a low-density phenolic resin matrix to form a rigid ablator. The phenolic resin matrix does not have structural load transfer requirements, and testing has shown that the phenolic resin can fully satisfy thermal requirements when the matrix contains microcracks. Due to high stresses in the through-the-thickness direction of the material, phenolic microcracks may form in the matrix material, which would result in a reduction of stiffness. An exploratory study was conducted to determine if reduction in material stiffness would change the load paths and/or decrease the structural margins. A comparison was performed between a linear finite element analysis that did not take into account phenolic microcracking and an iterative linear finite element analysis that accounted for propagation of phenolic microcracking. Four subcases using varying assumptions were analyzed and the results indicate that the assumed strength at which the phenolic microcracking propagates was the critical parameter for determining the extent of microcracking in the phenolic matrix. Phenolic microcracking does not have an adverse effect on the structural response of the test article and is not a critical failure.

Langston, Sarah L.↗
NASA NTRS1977

Fuel system protection

The hazardous nature of most fuels and the potential for catastrophe if ignition should occur was investigated in regard to the design of adequate lightning protection for aircraft fuel systems. Typical aircraft fuel flammability characteristics and possible ways to control fuel flammability and ignition were reviewed. Guidelines for effective protection of fuel systems were delineated.

Franklin A Fisher↗
NASA NTRS1971

Fabrication of titanium thermal protection system panels by the NOR-Ti-bond process

A method for fabricating titanium thermal protection system panels is described. The method has the potential for producing wide faying surface bonds to minimize temperature gradients and thermal stresses resulting during service at elevated temperatures. Results of nondestructive tests of the panels are presented. Concepts for improving the panel quality and for improved economy in production are discussed.

Wells, R. R.↗