Search NASA⌕ Search

SEARCH · Search NASA

Results for “qualitative analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Analytical simulation of the far-field jet noise and the unsteady jet flow-field by a model of periodic shedding of vortex ring from the jet exit

The construction of a theoretical flow field due to shedding of vortex rings, the identification of the controlling parameters, and the determination of whether the theoretical model successfully simulated the unsteady pressure field near jet (and consequently the far field noise) was studied. The basic parameters contained in the analytic solutions were the epoch at which a vortex ring was shed near the jet exit and the eddy viscosity coefficient. These parameters were identified from the experimental data for the real-time pressure and from the spread of the mixing layer of the jet. Results of the theoretical analysis show good qualitative agreement with the experimental data.

Liu, C. H.↗
NASA NTRS1977

Analytical methods for toxic gases from thermal degradation of polymers

Toxic gases evolved from the thermal oxidative degradation of synthetic or natural polymers in small laboratory chambers or in large scale fire tests are measured by several different analytical methods. Gas detector tubes are used for fast on-site detection of suspect toxic gases. The infrared spectroscopic method is an excellent qualitative and quantitative analysis for some toxic gases. Permanent gases such as carbon monoxide, carbon dioxide, methane and ethylene, can be quantitatively determined by gas chromatography. Highly toxic and corrosive gases such as nitrogen oxides, hydrogen cyanide, hydrogen fluoride, hydrogen chloride and sulfur dioxide should be passed into a scrubbing solution for subsequent analysis by either specific ion electrodes or spectrophotometric methods. Low-concentration toxic organic vapors can be concentrated in a cold trap and then analyzed by gas chromatography and mass spectrometry. The limitations of different methods are discussed.

Hsu, M.-T. S.↗
NASA NTRS1979

Nonparallel stability of two-dimensional nonuniformly heated boundary-layer flows

An analysis is presented for the linear stability of water boundary-layer flows over nonuniformly flat plates. Included in the analysis are disturbances due to velocity, pressure, temperatures, density, and transport properties as well as variations of the liquid properties with temperature. The method of multiple scales is used to account for the nonparallelism of the mean flow. In contrast with previous analyses, the nonsimilarity of the mean flow is taken into account. No analysis agrees, even qualitatively, with the experimental data when similar profiles are used. However, both the parallel and nonparallel results qualitatively agree with the experimental results of Strazisar and Reshotko when nonsimilar profiles are used.

Nayfeh, A. H.↗
NASA NTRS1981

Investigation of Antarctic crust and upper mantle using MAGSAT and other geophysical data

Progress in processing and analysis of Investigator B MAGSAT data is reported. Data processing tasks required prior to data analysis, including translation and reformatting of tapes and development of computer routines, were performed. A scalar anomaly map of Antarctica is near completion. Data analysis included a qualitative correlation of NASA's 4/81 scalar map of Antarctica with other geopotential data and correlation of POGO and continental scale gravity data with MAGSAT data. A magnetic high was found to exist over the Ross Embayment.

Bentley, C. R.↗
NASA NTRS1985

Scattering of acoustic waves into Tollmien-Schlichting waves by small streamwise variations in surface geometry

By using the triple-deck scaling of Stewartson (1969) and Messiter (1970) it is shown that small but relatively sudden surface geometry variations that produce only very weak static pressure variations can nevertheless produce strong, i.e. O(1), coupling between an externally imposed acoustic disturbance and a spatially growing Tollmien-Schlichting wave. The analysis provides a qualitative explanation of the Leehey and Shapiro (1979) boundary-layer receptivity measurements and is in good quantitative agreement with the Aizin and Poliakov (1979) experiment. It may also explain why small 'trip wires' can promote early transition.

Goldstein, M. E.↗
NASA NTRS1987

An analytical and experimental investigation of resistojet plumes

As a part of the electrothermal propulsion plume research program at the NASA Lewis Research Center, efforts have been initiated to analytically and experimentally investigate the plumes of resistojet thrusters. The method of G.A. Simons for the prediction of rocket exhaust plumes is developed for the resistojet. Modifications are made to the source flow equations to account for the increased effects of the relatively large nozzle boundary layer. Additionally, preliminary mass flux measurements of a laboratory resistojet using CO2 propellant at 298 K have been obtained with a cryogenically cooled quartz crystal microbalance (QCM). There is qualitative agreement between analysis and experiment, at least in terms of the overall number density shape functions in the forward flux region.

Zana, L. M.↗
NASA NTRS1987

An analytical and experimental investigation of resistojet plumes

As a part of the electrothermal propulsion plume research program at the NASA Lewis Research Center, efforts have been initiated to analytically and experimentally investigate the plumes of resistojet thrusters. The method of Simons for the prediction of rocket exhaust plumes is developed for the resistojet. Modifications are made to the source flow equations to account for the increased effects of the relatively large nozzle boundary layer. Additionally, preliminary mass flux measurements of a laboratory resistojet using CO2 propellant at 298 K have been obtained with a cryogenically cooled quartz crystal microbalance (QCM). There is qualitative agreement between analysis and experiment, at least in terms of the overall number density shape functions in the forward flux region.

Zana, Lynnette M.↗
NASA NTRS1988

Application of bifurcation theory to axial flow compressor instability

When a compression system goes unstable, the mode of response depends on the operating and system parameters, such as throttle setting and B parameter. Previous numerical work on the model developed by Moore and Greitzer (1986) has provided a limited picture of the parametric effects. Applying bifurcation theory to a single-harmonic version of the model has supplied much more complete information, defining the boundaries of each mode of response in the parameter space. Specifically, this is shown in a plot of B vs. throttle setting, which compares well with the corresponding map produced experimentally. The importance of the shape of the rotating stall characteristic is emphasized. The analysis shows a qualitative difference between classic surge and deep surge.

Mccaughan, F. E.↗
NASA NTRS1950

Note on some observed effects of rocket motor operation on the base pressures of bodies in free light

Some measurements of the effects of rocket-motor operation on base pressure were obtained incidental to other research on some bodies in free flight. These data are presented and qualitatively analyzed. The analysis indicates that jet effects on drag are of sufficient importance to deserve consideration in the design of jet motor nozzles, especially for aircraft and missiles where the thrust and drag are of the same order of magnitude. The base-pressure changes induced by the jet should be considered in the structural design of the outer body skin on the aft portion of fuselages containing jets. (author)

Purser, Paul E↗
NASA NTRS1992

On a finite-state inflow application to flap-lag-torsion damping in hover

An aerodynamic model with a coupled set of generalized dynamic wake equations and hybrid equations of motion for an elastic blade are applied here to a two-blade untwisted stiff in-plane hingeless small-scale model rotor with torsionally soft blades. Blade root offset, precone, blade droop, pitch control stiffness, and blade pitch angle are included in the model rotor. Numerical results show that 3D tip relief effects within the nonuniform steady-state inflow are significant to predict steady-state aerodynamic loads and blade deflections. Eigenvalue results confirm the importance of unsteady 3D aerodynamics in predicting lead-lag damping and frequency. Eigenvector analysis correlations reinforced qualitative and quantitative shortcomings associated with quasi-steady 2D aerodynamic theory for aeroelastic applications in hover.

De Andrade, Donizeti↗
NASA NTRS1994

Magnetotail dynamics under isobaric constraints

Using linear theory and nonlinear MHD simulations, we investigate the resistive and ideal MHD stability of two-dimensional plasma configurations under the isobaric constraint dP/dt = 0, which in ideal MHD is equivalent to conserving the pressure function P = P(A), where A denotes the magnetic flux. This constraint is satisfied for incompressible modes, such as Alfven waves, and for systems undergoing energy losses. The linear stability analysis leads to a Schroedinger equation, which can be investigated by standard quantum mechanics procedures. We present an application to a typical stretched magnetotail configuration. For a one-dimensional sheet equilibrium characteristic properties of tearing instability are rediscovered. However, the maximum growth rate scales with the 1/7 power of the resistivity, which implies much faster growth than for the standard tearing mode (assuming that the resistivity is small). The same basic eigen-mode is found also for weakly two-dimensional equilibria, even in the ideal MHD limit. In this case the growth rate scales with the 1/4 power of the normal magnetic field. The results of the linear stability analysis are confirmed qualitatively by nonlinear dynamic MHD simulations. These results suggest the interesting possibility that substorm onset, or the thinning in the late growth phase, is caused by the release of a thermodynamic constraint without the (immediate) necessity of releasing the ideal MHD constraint. In the nonlinear regime the resistive and ideal developments differ in that the ideal mode does not lead to neutral line formation without the further release of the ideal MHD constraint; instead a thin current sheet forms. The isobaric constraint is critically discussed. Under perhaps more realistic adiabatic conditions the ideal mode appears to be stable but could be driven by external perturbations and thus generate the thin current sheet in the late growth phase, before a nonideal instability sets in.

Birn, Joachim↗
NASA NTRS1992

Vertical landing on an asteroid

This work is concerned with the final approach phase and vertical landing on an asteroid with a power-limited, electrically propelled spacecraft. With gravitational effects taken into account, a new solution to the fuel optimal vertical landing on an asteroid was obtained. In this solution, the spacecraft commanded acceleration is explicitly expressed as a function of vehicle velocity and time to go. Based on qualitative methods of analysis, the guidance strategy and the resulting trajectories were studied. It is shown that these fuel-optimal trajectories effectively assure a vertical soft landing on the asteroid. Results of numerical simulations for the vertical landing, starting from an elliptical orbit are presented.

Harel, D.↗
NASA NTRS1996

A system and methodology for measuring volatile organic compounds produced by hydroponic lettuce in a controlled environment

A system and methodology were developed for the nondestructive qualitative and quantitative analysis of volatile emissions from hydroponically grown 'Waldmann's Green' leaf lettuce (Lactuca sativa L.). Photosynthetic photon flux (PPF), photoperiod, and temperature were automatically controlled and monitored in a growth chamber modified for the collection of plant volatiles. The lipoxygenase pathway products (Z)-3-hexenal, (Z)-3-hexenol, and (Z)-3-hexenyl acetate were emitted by lettuce plants after the transition from the light period to the dark period. The volatile collection system developed in this study enabled measurements of volatiles emitted by intact plants, from planting to harvest, under controlled environmental conditions.

NASA Discipline Life Support Systems↗
NASA NTRS2001

[Real time 3D echocardiography]

Three-dimensional representation of the heart is an old concern. Usually, 3D reconstruction of the cardiac mass is made by successive acquisition of 2D sections, the spatial localisation and orientation of which require complex guiding systems. More recently, the concept of volumetric acquisition has been introduced. A matricial emitter-receiver probe complex with parallel data processing provides instantaneous of a pyramidal 64 degrees x 64 degrees volume. The image is restituted in real time and is composed of 3 planes (planes B and C) which can be displaced in all spatial directions at any time during acquisition. The flexibility of this system of acquisition allows volume and mass measurement with greater accuracy and reproducibility, limiting inter-observer variability. Free navigation of the planes of investigation allows reconstruction for qualitative and quantitative analysis of valvular heart disease and other pathologies. Although real time 3D echocardiography is ready for clinical usage, some improvements are still necessary to improve its conviviality. Then real time 3D echocardiography could be the essential tool for understanding, diagnosis and management of patients.

Review↗
NASA NTRS1991

Portable x-ray fluorescence spectrometer for environmental monitoring of inorganic pollutants

A portable x-ray fluorescence spectrometer has a portable sensor unit containing a battery, a high voltage power supply, an x-ray tube which produces a beam x-ray radiation directed toward a target sample, and a detector for fluorescent x-rays produced by the sample. If a silicon-lithium detector is used, the sensor unit also contains either a thermoelectric or thermochemical cooler, or a small dewar flask containing liquid nitrogen to cool the detector. A pulse height analyzer (PHA) generates a spectrum of data for each sample consisting of the number of fluorescent x-rays detected as a function of their energy level. The PHA can also store spectrum data for a number of samples in the field. A processing unit can be attached to the pulse height analyzer to upload and analyze the stored spectrum data for each sample. The processing unit provides a graphic display of the spectrum data for each sample, and provides qualitative and/or quantitative analysis of the elemental composition of the sample by comparing the peaks in the sample spectrum against known x-ray energies for various chemical elements. An optional filtration enclosure can be used to filter particles from a sample suspension, either in the form of a natural suspension or a chemically created precipitate. The sensor unit is then temporarily attached to the filtration unit to analyze the particles collected by the filter medium.

Thornton, Michael G.↗
NASA NTRS2008

Induced Contamination Predictions for JAXA's MPAC&SEED Devices

Externally mounted ISS payloads are exposed to the induced ISS environment, including material outgassing and thruster plume contamination. The Boeing Space Environments Team developed analytical and semiempirical models to predict material outgassing and thruster plume induced contamination. JAXA s SM/MPAC&SEED experiment provides an unique opportunity to compare induced contamination predications with measurements. Analysis results are qualitatively consistent with XPS measurements. Calculated depth of contamination within a factor of 2-3 of measured contamination. Represents extremely good agreement, especially considering long duration of experiment and number of outgassing sources. Despite XPS limitations in quantifying plume contamination, the measured and predicted results are of similar scale for the wake-facing surfaces. JAXA s JEM/MPAC&SEED experiment will also be exposed to induced contamination due to JEM and ISS hardware. Predicted material outgassing induced contamination to JEM/MPAC&SEED ranges from 44 to 262 (depending on surface temperature) for a 3 year exposure duration.

Steagall, Courtney↗
NASA NTRS2024

Plasma-Based Elemental Analyzer for Crewed Transit and Planetary Habitation

As NASA continues to perform research on the ISS and move towards the Moon and Mars, it is important for astronauts to have a technology capable of determining the composition of solid, liquid, and gas samples. Currently, samples are transported back to Earth for analysis, which may impact results due to the time delay of samples waiting to be returned to Earth as well as potential sample contamination from re-entry, change in environment, and various personnel handling. Therefore, researchers at the Applied Chemistry Lab at KSC have developed a proof-of-concept “Plasma-Based Elemental Analyzer,” which has the capability of testing solid, liquid, and gas samples for identification. Currently, the analysis is only qualitative, with quantitative identification left for future work. This technology is similar to ICP-OES, but differs in instrument size and sample preparation. Both technologies use plasma to ionize samples for light emission. The plasma elemental analyzer aims to be portable and lightweight, require only electrical power, and analyze solid, liquid, and gas samples. It does not use acid digestion or a nebulizer, requires less power than ICP-OES, and is able to operate with minimal to no usage of argon gas. Furthermore, the plasma elemental analyzer operates within low power constraints, which makes it feasible for usage on future missions with higher power constraints. The technology was tested at atmospheric pressure using mostly room air as the carrier gas for plasma production in the proof-of-concept study. The results showed the peak signals of the elements with an associated arbitrary signal intensity that allowed for qualitative identification. Solid samples that were tested included inedible biomass from the Golden Heirloom Cherry Tomato plant and Lunar Highlands Simulants (LHS-1). The liquid samples included elements of interest for the space crop production community. This work showed that a system smaller than the traditional ICP-OES equipment is able to be designed and implemented in future use cases, although it requires further development.

Kenneth Engeling↗
NASA NTRSDate not supplied

Human-AI Collaboration Among Engineering and Design Professionals: Three Strategies of Generative AI Use

Designers are increasingly using Generative Artificial Intelligence (GenAI) in design processes; however, knowing how designers use GenAI--especially in professional design practice--is under-explored. This paper presents an ethnographic study of a design team at NASA that explores the natural variation of GenAI use across team members during a speculative design workflow. We aimed to uncover when, how, and why GenAI tools were or were not employed using ethnographic observations to map the team's speculative design process and follow-up interviews to provide deeper insights into team members' interactions (or lackthereof) with GenAI. Through inductive qualitative coding, our analysis revealed three strategies of GenAI use observed among professional engineers and designers--intimate co-design with GenAI, selective delegation to GenAI, and minimal use of GenAI--as well as factors that appeared to influence their decisions whether or not to use GenAI. This study proposes new theory in human-AI collaboration that sheds light on the strategies, rationale, and circumstances under which design professionals use GenAI. Future work that builds upon these insights include examining a larger sample size of engineering and design professionals in uncontrolled design process experiences and exploring the impact that design tasks, goals, and constraints have on a participants decision to leverage GenAI tools.

design practice↗