Search NASA⌕ Search

SEARCH · Search NASA

Results for “resins”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Unraveling Reactivity Differences: Room-Temperature Ring-Opening Metathesis Polymerization (ROMP) versus Frontal ROMP

Here, in this study, we explore the distinct reactivity patterns between frontal ring-opening metathesis polymerization (FROMP) and room-temperature solventless ring-opening metathesis polymerization (ROMP). Despite their shared mechanism, we find that FROMP is less sensitive to inhibitor concentration than room-temperature ROMP. By increasing the initiator-to-monomer ratio for a fixed inhibitor/initiator quantity, we find reduction in the ROMP background reactivity at room temperature (i.e., increased resin pot life). At elevated temperatures where inhibitor dissociation prevails, accelerated frontal polymerization rates are observed because of the concentrated presence of the initiator. Surprisingly, the strategy of employing higher initiator loading enhances both pot life and front speeds, which leads to FROMP rates exceeding prior reported values by over 5 times. This counterintuitive behavior is attributed to an increase in the proximity of the inhibitor to the initiator within the bulk resin and to whether the temperature favors coordination or dissociation of the inhibitor. A rapid method was developed for assessing resin pot life, and a straightforward model for active initiator behavior was established. Modified resin systems enabled direct ink writing of robust thermoset structures at rates much faster than previously possible.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Data for "Adsorptive Separation and Recovery of Triacetic Acid Lactone from Fermentation Broth"

Triacetic acid lactone (TAL) can be microbially produced and further chemically upgraded to several high-value chemicals. In this work, several acidic and basic ion-exchange resins and activated charcoal were evaluated for their ability to adsorb microbially produced TAL. Activated charcoal and a weak base resin, Dowex 66, showed similar TAL adsorption capacity of 0.18 ± 0.002 g/g. At 15% w/v activated charcoal, about 98% of TAL present in fermentation broth could be adsorbed. Further, ethanol washing allowed recovery of 72% of adsorbed TAL. A biorefinery producing TAL from sucrose was designed, simulated, and evaluated (through technoeconomic analysis) under uncertainty, for an estimated TAL minimum product selling price (MPSP) of $4.27/kg [$3.71−4.94/kg; 5th-95th percentiles] for the current state of technology and $2.83/kg [$2.46–3.29/kg] following potential near-term improvements to fermentation. Thus, this work provides an adsorptive process to recover microbially produced TAL that can be chemically upgraded to several industrial products.

Bioproducts↗
DOE OSTI2026

MAT 332: Recyclable-By-Design Carbon Fiber Composites for Battery Enclosures

This work aims to fabricate a small-scale battery module with the baseline RBD-CFRC and conduct mechanical crush test to develop an initial thermal runaway model. Test the adhesive properties of the RBD-CFRCs using their resin constituent, ultrasonic welding, and other resins employed today. Recommend a future direction for resin development to enable the welding of RBDCFRCs to dissimilar materials. Time and Cost Permitting. Iterate on resin development for flame resistance and adhesive properties, demonstrating how thermal runaway can be reduced or joining properties can be improved.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Investigating Core Gaps and the Development of Subcomponent Validation Methods for Wind Turbine Blades: Preprint

Core gaps are a common manufacturing defect observed in wind blade composite sandwich constructions, which occur when sheets of core material are not properly butted up against each other in the mold. The aim of this study was to characterize core gaps in composite sandwich constructions at the coupon scale. This was to gain an initial understanding of the defect before developing appropriate methodologies for more complex subcomponents as part of a much broader wind blade structural validation and damage tolerance program. Long beam flexure in 4-point-bending was chosen as the most appropriate loading scenario. Beam specimens were characterized with and without 10 mm core gaps in fiberglass/balsa sandwich beams. The core gaps were characterized with two separate resin systems; a Hexion epoxy and Arkema's Elium resins system (a novel, infusible thermoplastic). Results showed that the Elium beams without the core gaps were had a 15% lower static strength than their epoxy counterparts. The introduction of the core gap to the epoxy beams reduced their static strength by 35%. The Elium beams, however, exhibited negligible strength reductions with the inclusion of the core gap. Overall, this characterization study provided pertinent information with regards to core gaps as a manufacturing defect to allow for continued development of damage tolerance and subcomponent validation methodologies with the inclusion of manufacturing defects.

17 WIND ENERGY↗
DOE OSTI2024

Polymer Nanocomposite Sensors with Improved Piezoelectric Properties through Additive Manufacturing

Additive manufacturing (AM) technology has recently seen increased utilization due to its versatility in using functional materials, offering a new pathway for next-generation conformal electronics in the smart sensor field. However, the limited availability of polymer-based ultraviolet (UV)-curable materials with enhanced piezoelectric properties necessitates the development of a tailorable process suitable for 3D printing. This paper investigates the structural, thermal, rheological, mechanical, and piezoelectric properties of a newly developed sensor resin material. The polymer resin is based on polyvinylidene fluoride (PVDF) as a matrix, mixed with constituents enabling UV curability, and boron nitride nanotubes (BNNTs) are added to form a nanocomposite resin. The results demonstrate the successful micro-scale printability of the developed polymer and nanocomposite resins using a liquid crystal display (LCD)-based 3D printer. Additionally, incorporating BNNTs into the polymer matrix enhanced the piezoelectric properties, with an increase in the voltage response by up to 50.13%. This work provides new insights for the development of 3D printable flexible sensor devices and energy harvesting systems.

42 ENGINEERING↗
DOE OSTI2020

System and method for forming activated carbon aerogels and performing 3D printing

Making a carbon aerogel involves 3-D printing an ink to make a printed part, removing the solvent from the printed part, and carbonizing the printed part (with the solvent removed) to make the aerogel. The ink is based on a solution of a resorcinol-formaldehyde resin (RF resin), water, and an organic thickener. Advantageously, the RF resin contains an acid catalyst, which tends to produce carbon aerogels with higher surface areas upon activation than those produced from methods involving an ink composition containing a base catalyzed resin.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Use of latent metathesis polymerization systems for additive manufacturing

The invention is directed to latent metathesis-active resin compositions and additive manufacturing approaches. The latent metathesis-active compositions comprise at least one latent metathesis catalyst, at least one curable metathesis-active monomer, and optional fillers, photosensitizers, and/or a secondary monomer resin system for dual-cure. A method comprises extruding a latent metathesis-active resin from a dispensing apparatus and spatially triggering a ring-opening metathesis polymerization by directed irradiation with light or directed application of a thermal stimuli for direct-ink write printing of objects. Another method uses a latent metathesis-active resin for vat photopolymerization and stereolithographic printing of objects.

Appelhans, Leah↗
DOE OSTI2024

Method of printing and implementing refractive X-ray optical components

A method of fabricating a refractive optical element on a substrate may provide less expensive and more compact optics for an X-ray system. The method includes coating the substrate with a resin and providing radiation to a portion of the resin to cause two photon polymerization of the resin. The method further includes forming, by two photon polymerization, a first surface of a polymer refractive optical element from the resin. The first surface is disposed along an optical axis of the refractive optical element and the first surface has a roughness of less than 100 nanometers. Further, the method includes forming, by two photon polymerization, a second surface of the polymer refractive optical element. The second surface is disposed along the optical axis of the refractive optical element and the second surface has a roughness of less than 100 nanometers.

Jiang, Zhang↗
DOE OSTI2025

Operational Experience and Development of a Reliability Model for the ATR Demineralizer System (Slides)

The Advanced Test Reactor (ATR) is a light water reactor with aluminum clad driver fuel. Strict limits are implemented on pH, conductivity, and filterable solids to assure the performance of the driver fuel limit corrosion of the primary coolant system (PCS) pressure boundary components. A bypass demineralizer system is used to maintain PCS coolant within allowable bands for each of the aforementioned variables. Unlike many other reactors, the ATR does not have a filtration system. As such, failure of ion exchange resin in the bypass demineralizer can defeat the purpose of the system and result in high filterable solids in the PCS. Power operations with high filterable solids is prohibited by a technical safety requirement. This paper discusses recent failures of the ATR bypass demineralizer system. The testing and analysis done to deduce the cause of the failures is covered, as well as short term mitigative steps that were taken. To prevent the likelihood of future issues, historical data from the ATR and industry is used to develop a reliability model of the ATR bypass demineralizer system. Evidence of radiolytic decomposition of ion exchange resin was found in the cause investigation. As such, special attention is given to ion exchange resin failure due to high radiation environments. The reliability model is used to develop the ATR testing and maintenance program. Specifically, limits on resin service life are discussed.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2024

Improved titanium-44 purification process for establishing a high apparent molar activity titanium-44/scandium-44 generator

44 Sc-radiopharmaceuticals are gaining more interest but still lack availability. The proof of principle of a 44 Ti/ 44 Sc generator, which can produce 44 Sc daily, has been established but with some limitations and drawbacks. Despite recent advances, separation of 44 Ti from massive quantities of scandium target material is still cumbersome. Here, in this work, the improved radiochemical separation of 44 Ti from residual scandium target material was carried out by precipitation of Sc with fluoride ions. Furthermore, two approaches were used to set up a high apparent molar activity small-scale generator. The first method relied on extraction chromatography for fine purification using a DGA resin, followed by loading of the purified 44 Ti onto a ZR resin column. In the second method, 44 Ti was loaded on the ZR resin directly after the precipitation step. This second method was used to set up a generator of 370 kBq and evaluate by radiolabeling. An apparent molar activity of 2 MBq/nmol was obtained for the radiolabeling with DOTA, the most common and suitable chelate for scandium. This result is comparable with previously published data on 44m/44 Sc.

44Sc↗
DOE OSTI2022

Anion exchange and extraction chromatography tandem column isolation of zirconium-89 ( 89 Zr) from cyclotron bombarded targets using an automated fluidic platform

The long-lived positron emitter 89 Zr is a highly promising nuclide employed in diagnostic Positron Emission Tomography (PET) imaging. Methods of radiochemical processing to obtain 89 Zr for clinical use are traditionally performed with a single hydroxamate resin column. In this work, we present a tandem column purification method for the preparation of high-purity 89 Zr from cyclotron bombarded Y metal foils. The primary column is a macroporous, strongly basic anion exchange resin on styrene divinylbenzene co-polymer. The secondary microcolumn, with an internal volume of 33 µL, is packed with an extraction chromatography resin (ExCR) loaded with HDEHP. A condition of “inverted selectivity” is presented, wherein the 89 Zr elution from the primary column is synonymous with the load condition on the secondary column. The ability to transfer 89 Zr from one column to the next allows two sequential column clean-up methods to be performed prior to the final elution of the 89 Zr product. This approach assures delivery of very high purity 89 Zr . The tandem column purification process has been implemented into a prototype automated fluidic system. Optimization of the method is presented, followed by evaluation of the process using seven cyclotron bombarded Y metal foil targets. Once optimized, we found that 93.7±2.3% of the 89 Zr present in the foils was recovered in the secondary column elution fraction (0.8 M oxalic acid). Radiochromatograms of the product elution peaks enabled determination of full width at half-maximum (FWHM) and 89 Zr collection yields as a function of volume. Because of the small size of the secondary microcolumn, a 89 Zr product volume of ~0.28 mL is reported, which provides a substantially increased nuclide concentration over traditional methods. Finally, we evaluated the transchelation of the resulting 89 Zr oxalate product to deferoxamine mesylate (DFOM) salt. We observed effective specific activities (ESA) and bindable metals concentrations ([M B ]) that exceed those reported by the traditional single hydroxamate column method.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Highly Tunable Thiol-Ene Photoresins for Volumetric Additive Manufacturing

Volumetric additive manufacturing (VAM) forms complete 3D objects in a single photocuring operation without layering defects, enabling 3D printed polymer parts with mechanical properties similar to their bulk material counterparts. This study presents the first report of VAM-printed thiol-ene resins. With well-ordered molecular networks, thiol-ene chemistry accesses polymer materials with a wide range of mechanical properties, moving VAM beyond the limitations of commonly used acrylate formulations. Since free-radical thiol-ene polymerization is not inhibited by oxygen, the nonlinear threshold response required in VAM is introduced by incorporating 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) as a radical scavenger. Tuning of the reaction kinetics is accomplished by balancing inhibitor and initiator content. Coupling this with quantitative measurements of the absorbed volumetric optical dose allows control of polymer conversion and gelation during printing. Importantly, this work thereby establishes the first comprehensive framework for spatial–temporal control over volumetric energy distribution, demonstrating structures 3D printed in thiol-ene resin by means of tomographic volumetric VAM. Mechanical characterization of this thiol-ene system, with varied ratios of isocyanurate and triethylene glycol monomers, reveals highly tunable mechanical response far more versatile than identical acrylate-based resins. This broadens the range of materials and properties available for VAM, taking another step toward high-performance printed polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multi‐Material Gradient Printing Using Meniscus‐enabled Projection Stereolithography (MAPS)

Light‐based additive manufacturing methods are widely used to print high‐resolution 3D structures for applications in tissue engineering, soft robotics, photonics, and microfluidics, among others. Despite this progress, multi‐material printing with these methods remains challenging due to constraints associated with hardware modifications, control systems, cross‐contamination, waste, and resin properties. Here, a new printing platform coined Meniscus‐enabled Projection Stereolithography (MAPS) is reported, a vat‐free method that relies on generating and maintaining a resin meniscus between a crosslinked structure and bottom window to print lateral, vertical, discrete, or gradient multi‐material 3D structures with no waste and user‐defined mixing between layers. MAPS is compatible with a wide range of resins shown and can print complex multi‐material 3D structures without requiring specialized hardware, software, or complex washing protocols. MAPS's ability to print structures with microscale variations in mechanical stiffness, opacity, surface energy, cell densities, and magnetic properties provides a generic method to make advanced materials for a broad range of applications.

bioprinting↗
DOE OSTI2025

Dielectric Barrier Discharge Electrothermal Heating and Additive Manufacturing of Thermoset Parts

Additive manufacturing of thermosets requires a mechanism for solidifying deposited layers in order to prevent part collapse. To accomplish this, non‐equilibrium plasma is proposed for its ability to target, heat, and cure printed thermosetting resin. Non‐equilibrium plasmas have not been used for the curing of liquid thermoset composites, and so their impact on an uncured resin is unknown. Here this work investigates the mechanism through which dielectric barrier discharge (DBD) heats an epoxy/carbon nanotube (CNT) composite under atmospheric conditions. Plasma applied to resin surfaces is found to cause rapid heating, with heating rate controlled by adjusting the applied power. Heating is localized to within the top 0.5 mm of the sample surface and maximum temperature is found to depend on sample conductivity, indicating the heating reaction occurs through a combination of electron conduction and ion bombardment. Characterization of composites cured using plasma shows oxidation and roughening of the surface. Based on the heating and surface studies, several demonstrative prints are performed using in situ plasma curing. This work shows the potential of DBD plasma to rapidly heat liquid substrates and demonstrates how plasma curing expands the capability of existing direct ink write (DIW) printer technologies.

3D printing↗
DOE OSTI2023

Reduced graphene oxide catalytically enhances the rate of cyanate ester curing under variable frequency microwave heating

Here, the curing of Lonza Primaset PT-30 novolac cyanate ester resin and EPON 826 bisphenol-A diglycidyl ether were investigated using convective thermal heating and variable frequency microwave (VFM) heating. The addition of 1 part per hundred reduced graphene oxide (r-GO) to PT-30 novolac cyanate ester increased the VFM cure rate compared to thermal heating. Curing it at 160°C for 240 min with VFM heating resulted in a 55% degree of cure compared to a 26% degree of cure with thermal heating. This observed VFM rate enhancement is due to selective microwave heating of the r-GO particles in the resin resulting in increased r-GO catalytic activity toward cyanate ester curing. It is both a thermal and catalytic effect, the latter of which is absent when r-GO is added to a bisphenol-A diglycidyl ether resin with o-phenylenediamine hardener. Impurities present in the PT-30 matrix do not appear to contribute to its overall cure kinetics, nor do they participate in the observed VFM rate enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Reducing Antisolvent Use in the STRAP Process by Enabling a Temperature–Controlled Polymer Dissolution and Precipitation for the Recycling of Multilayer Plastic Films

The recently reported processing strategy called solvent-targeted recovery and precipitation (STRAP) enables deconstruction of multilayer plastic packaging films into their constituent resins by selective dissolution. It uses a series of solvent washes that are guided by thermodynamic calculations of polymer solubility. In this work, the use of antisolvents in the STRAP process was reduced and solvent mixtures were considered to enable the temperature-controlled dissolution and precipitation of the target polymers in multilayer films. This was considered as a means to further improve the STRAP process and its estimated costs. Two STRAP approaches were compared based on different polymer precipitation techniques: precipitation by the addition of an antisolvent (STRAP-A) and precipitation by decreasing the solvent temperature (STRAP-B). Both approaches were able to separate the constituent polymers in a post-industrial film composed primarily of polyethylene (PE), ethylene vinyl alcohol (EVOH), and polyethylene terephthalate (PET) with near 100 % material efficiency. Technoeconomic analysis indicates that the minimum selling price (MSP) of the recycled resins with STRAP-B is 21.0 % lower than that achieved with STRAP-A. This provides evidence that thermally driven polymer precipitation is an option to reduce the use of antisolvents, making the STRAP process more economically and environmentally attractive. A third process, STRAP-C, was demonstrated with another post-industrial multilayer film of a different composition. Here, the results demonstrate that this process can also recover polymers at similar costs to those of virgin resins, indicating that the STRAP technology is flexible and can remain economically competitive as the plastic feed complexity is increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Development of transparent, particle‐loaded photoresins for volumetric additive manufacturing of silica glass

Abstract Additive manufacturing of glass aims to change the paradigm of glass manufacturing by allowing for improved customization coupled with lower energy and post‐processing needs. Fabrication of glass via volumetric additive manufacturing (VAM) involves printing in a silica‐loaded photopolymer resin with subsequent thermal processing and adds additional advantages by allowing for rapid printing of parts with smooth surfaces and no supports. Previous work in glass VAM has demonstrated fabrication of optical quality microoptics with overall dimensions on the scale of tens of cubic millimeters. For applications requiring glass printed on the scale of cubic centimeters the rheology, scattering, and green part strength must be controlled via resin formulation. Here, we present insight into a novel glass photopolymer resin suitable for VAM and in the effect of tuning formulation on the ability to produce dense glass parts with volumes on the scale of cubic centimeters.

Myers, Luke A.↗
DOE OSTI2024

Improving the Recyclability of Polymer Composites With Cellulose Nanofibrils

Cellulose nanofibers (CNFs) have been widely studied for their reinforcing potential in high-performance composites. While there are numerous publications on CNF-reinforced composites in a variety of polymer matrices, few have considered the recyclability of such thermoplastic composites and whether the incorporation of CNFs deteriorates or improves their performance upon reprocessing. In this study, two thermoplastic resins, poly(lactic acid) (PLA), and glycol-modified polyethylene terephthalate (PETg), were prepared with CNF reinforcement and thermomechanically recycled to investigate the effect of CNF inclusion on the composite properties after reprocessing as well as their effect on the composites’ number of useful life cycles. Additionally, changes in mechanical, thermal, rheological, molecular, and microstructural properties of the composites and/or base resins were monitored as a function of cycle numbers. As is typical, the polymers’ molecular weight and mechanical performance deteriorated with continued processing. However, the addition of spray dried CNF was found to better maintain the mechanical performance of both polymers throughout multiple recycling steps as compared to neat samples. For example, the tensile strength of PETg with 20 wt% CNF after 6 processing cycles was found to exceed that of virgin neat PETg, and higher loadings of CNF were found to preserve a higher yield strength during multiple rounds of reprocessing compared to PETg composites with lower CNF loadings. Ultimately this study indicates that the addition of CNF to some thermoplastic materials can increase both their sustainability by offsetting the use of high-embodied energy resins and their circularity by enabling performance retention over more use cycles.

42 ENGINEERING↗