Search NASA⌕ Search

SEARCH · Search NASA

Results for “second harmonic generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

On the structure of artificially generated water wave trains

The structure of an artificially generated sinusoidal water wave train of fixed frequency under the influence of wind is analyzed. Artificially generated waves of 1 Hz are studied at seven wind speeds in the range of 140-400 cm/s. It is observed that the water wave train deformed by wind consists of two components at both the fundamental mode and the harmonics. The amplitude and phase of the wave components are derived, and the dispersion relation and component phase speeds are examined. The data reveal that the amplitude of the forced and free-traveling second harmonics correlate with previous theories, and that the deviation of the measured phase speed from the linear theory is caused by the nonlinearity of the primary wave, the interaction between short gravity waves and the primary wave, and the advection effects of wind drift.

Papadimitrakis, Yiannis A.↗

Improving Power Density of Free-Piston Stirling Engines

Analyses and experiments demonstrate the potential benefits of optimizing piston and displacer motion in a free-piston Stirling Engine. Isothermal analysis shows the theoretical limits of power density improvement due to ideal motion in ideal Stirling engines. More realistic models based on nodal analysis show that ideal piston and displacer waveforms are not optimal, often producing less power than engines that use sinusoidal piston and displacer motion. Constrained optimization using nodal analysis predicts that Stirling engine power density can be increased by as much as 58 percent using optimized higher harmonic piston and displacer motion. An experiment is conducted in which an engine designed for sinusoidal motion is forced to operate with both second and third harmonics, resulting in a piston power increase of as much as 14 percent. Analytical predictions are compared to experimental data and show close agreement with indirect thermodynamic power calculations, but poor agreement with direct electrical power measurements.

aerospace engineering↗

Wide-Bandgap Semiconductor Amplifiers for Fusion Plasma Heating and Control

This paper discusses power electronics developed under the ARPA-E GAMOW program to support nuclear fusion power production. The goal of this project was to develop and assess the potential for wide-bandgap (WBG) semiconductor devices in power electronics to enable high-efficiency and high-voltage solid-state systems for fusion plasma generation, heating, and control. The power electronics use an architecture in which multiple high-power boards can be combined to produce megawatt-level power, where using multiple boards provides high reliability. Two main areas of power electronics boards are developed in this project for fusion plasma heating and control applications: (1) pulse generation and control and (2) radiofrequency generation. The first area is for boards capable of driving high-voltage millisecond pulses at high duty cycles. The envisioned application of these pulses is in plasma control of magnetohydrodynamic instabilities, plasma position, and edge-localized modes. Pulse-width modulation allows for the implementation of a wide variety of linear and nonlinear control systems. The boards developed for this project could actuate control coils based on digital input signals and can be parallelized to provide megawatts of output power. The design of the pulse generator is a low-side load switch. A load switch was designed and constructed that utilized 2-kV-rated field-effect transistor (FET)-based cascodes developed by Qorvo under this project to perform initial testing of these cascodes. The second area is being implemented using class E amplifiers with WBG devices and a reactance steering network to handle inductive or capacitive plasma loads. Applications include ion cyclotron resonance heating (ICRH) and high-harmonic fast-wave (HHFW) heating. A class E reactance steering network is demonstrated in modeling and experiment with a resistive-inductive load that models an inductively-coupled plasma. Power combining of boards with class E reactance steering networks is also simulated and demonstrated experimentally, to enable scaling up to high power. Modeling of high-power-density cooling and remaining useful life is conducted to enable reliable, effectively cooled high-power electronics for fusion applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

On the generation of the sequence of diffuse resonances observed on top side ionograms

Two different plasma wave instabilities have been invoked in earlier models for the generation of top side ionogram diffuse resonances. Arguments are presented that support the model based on the Harris instability, i.e., the instability resulting from a sounder-stimulated anisotropic electron velocity distribution. Two modifications to this model are also presented. First, it is only necessary for the instability mechanism to operate for a period of the order of milliseconds (rather than tens of milliseconds) in order to explain the observations. Second, the wave associated with the second harmonic of the electron cyclotron frequency, which enters into the nonlinear wave-wave interaction process included in the model, comes from the side bands of the transmitted sounder pulse rather than from the turbulent state of the plasma caused by the pulse. The second modification provides an explanation for the variation of the time duration observed among the members of the sequence of diffuse resonances.

Benson, R. F.↗

Unsteady transonic airfoil computation using implicit Euler scheme on body-fixed grid

The unsteady Euler equations have been derived for the flow relative motion with respect to a frame of reference that is rigidly attached to the moving airfoil. The grid is generated once by an elliptic solver without a need for dynamic grid computation. An implicit factored finite-volume scheme has been developed and implemented through a fully vectorized computer program. Implicit second-order and explicit second and fourth-order dissipations are added to the scheme. The boundary conditions are explicitly satisfied. The scheme is applied to steady and unsteady transonic airfoil flows and the results are in good agreement with the experimental data. For forced harmonic airfoil motions, periodic solutions are achieved within the third cycle of oscillation.

Kandil, Osama A.↗

Student Support for the “Frontiers in Attosecond & Ultrafast X-ray Science” School

The new millennium witnessed two revolutionary breakthroughs in ultrafast x-ray science: table-top XUV sources based on high harmonic generation in gases ushered in the attosecond era while facility-based x-ray free-electron lasers opened the path for intense, femtosecond hard x-rays. This award requested scholarship funds for a 2019 and 2023 School whose prime objective was the training of young scientists in these emerging complementary areas both relevant to DOE BES mission. The school entitled the “Frontiers of Attosecond and Ultrafast X-ray Science (FAXS)” (http://www.erice-attosecond.it/) was the second and fourth in a series, which began in 2017. The two Schools were held during March 10-16, 2019 and March 26-31, 2023 at the Ettore Majorana Foundation and Centre for Scientific Culture (http://www.ccsem.infn.it/) in Erice, Sicily. The DOE funds supported the registration fee for young scientists (graduate students and postdocs) from US institutions. The registration fees included School participation, lodging and meals over the duration of the School. Note, the third addition of the School was held in 2022 as a virtual event due to the pandemic, DOE funds were not necessary for this event. The FAXS School is a course of the 62th and 63rd International School of Quantum Electronics under the directorship of Prof. Diederik Wiersma (University of Florence). The Directors for the FAXS School are Louis DiMauro (The Ohio State University, USA) and Mauro Nisoli (Politecnico di Milano, Italy). The FAXS School program consisted of approximately 10 lectures by leading experts in attosecond and x-ray science (see attached list). Most lecturers delivered a series of three 1-hour lectures. The lecturers were required to spend the full 5 days at the school so to promote interaction with the students. The Erice Majorana Center venue accommodated ~75 young scientists. The registration fee covered the cost of participating in the school, lodging and meals for the entire duration of the school. The schedule consisted of lectures every morning and afternoon except for one afternoon that was reserved for an archaeological excursion. Every evening had a student/postdoc poster session and social gatherings at the Majorana Center to encourage further interaction of all participants and lecturers. The two FAXS Schools attracted an international group of young scientists. The DOE funds supported the registration fee for 11 students/postdocs from US institutions (5 supported in 2019 and 6 supported in 2023). The management of the DOE fellowships were administered through the Research Foundation of The Ohio State University. FAXS scholarships for European students/postdocs were provided by European funding sources administered by co-Director, Prof. Nisoli. All students/postdocs were encouraged to present a poster. Travel expenses to the FAXS School were the responsibility of the student/postdoc home institution.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Miniature MMIC Low Mass/Power Radiometer Modules for the 180 GHz GeoSTAR Array

We have developed and demonstrated miniature 180 GHz Monolithic Microwave Integrated Circuit (MMIC) radiometer modules that have low noise temperature, low mass and low power consumption. These modules will enable the Geostationary Synthetic Thinned Aperture Radiometer (GeoSTAR) of the Precipitation and All-weather Temperature and Humidity (PATH) Mission for atmospheric temperature and humidity profiling. The GeoSTAR instrument has an array of hundreds of receivers. Technology that was developed included Indium Phosphide (InP) MMIC Low Noise Amplifiers (LNAs) and second harmonic MMIC mixers and I-Q mixers, surface mount Multi-Chip Module (MCM) packages at 180 GHz, and interferometric array at 180 GHz. A complete MMIC chip set for the 180 GHz receiver modules (LNAs and I-Q Second harmonic mixer) was developed. The MMIC LNAs had more than 50% lower noise temperature (NT=300K) than previous state-of-art and MMIC I-Q mixers demonstrated low LO power (3 dBm). Two lots of MMIC wafers were processed with very high DC transconductance of up to 2800 mS/mm for the 35 nm gate length devices. Based on these MMICs a 180 GHz Multichip Module was developed that had a factor of 100 lower mass/volume (16x18x4.5 mm3, 3g) than previous generation 180 GHz receivers.

Monolithic Microwave Integrated Circuit (MMIC)↗

Non-resonant picosecond three-wave mixing in the gas phase

We report on the experimental observation of non-resonant, second-order optical sum-frequency generation (SFG) in five different atomic and molecular gases. The measured signal is attributed to a SFG process by characterizing its intensity scaling and its polarization behavior. We show that the electric quadrupole mechanism cannot explain the observed trends and suggest a mechanism based on symmetry breaking along the incident beam path arising from laser-induced species ground state number density gradients. Our results demonstrate that the SFG is about four orders of magnitude stronger than the third-harmonic generation (THG) and independent from any externally applied electric fields. In conclusion, these features make this method suitable for gas number density measurements at the picosecond time scale in reactive flows and plasmas.

LaCombe, Grayson↗

Standing hydromagnetic oscillations in the magnetosphere

The mechanisms for generating Alfven waves in the magnetosphere are determined, on the basis of a comprehensive survey of satellite magnetometer data. The mechanisms are classified in terms of the physical properties of standing Alfven waves such as the direction of the major axis of polarization, harmonic mode, and the azimuthal wave number. In an analysis of the statistical organization of the pulsations, it is shown that the most common transverse waves seem to be azimuthally polarized waves involving the fundamental and several harmonics, with radially polarized waves excited at the second harmonic. The former are probably driven externally, while the latter are likely to be excited internally through particle-wave interactions.

Takahashi, K.↗

Nonlinear disturbances in a hypersonic laminar boundary layer

Three separate but similar experiments on the growth of naturally-occurring instability waves in the laminar boundary-layers on sharp cones at hypersonic Mach numbers have been conducted. Each provided clear evidence that the theoretically-predicted second mode of instability was responsible for high-amplitude wave trains observed to prevail upstream of boundary-layer transition to turbulence. However, each also seemed to reveal the presence of an additional instability not accounted for by the linear theory. Here, examination is made of the tape-recorded hot-wire anemometer signals of one experiment on a sharp cone at Mach 8 for evidence of nonlinearity, the finding of which would explain the presence of the additional mode as a consequence of harmonic generation. Several approaches for identification of the residual effects of nonlinearity are described and utilized. Also, a simplified model describing certain fluctuation characteristics has been developed. Altogether, the evidence of nonlinear wave development is found to be strong. Quantitative comparisons of linear theory to experiments must be made with caution when nonlinearity is present in the experiment.

Kimmel, Roger L.↗

Optimum wavelengths for two color ranging

The range uncertainties associated with the refractive atmosphere can be mitigated by the technique of two color, or dual wavelength, ranging. The precision of the differential time of flight (DTOF) measurement depends on the atmospheric dispersion between the two wavelengths, the received pulsewidths and photoelectron counts, and on the amount of temporal averaging. In general, the transmitted wavelengths are not independently chosen but instead are generated via nonlinear optics techniques (harmonic crystals, Raman scattering, etc.) which also determine their relative pulsewidths. The mean received photoelectrons at each wavelength are calculated via the familiar radar link equation which contains several wavelength dependent parameters. By collecting the various wavelength dependent terms, one can define a wavelength figure of merit for a two color laser ranging system. In this paper, we apply the wavelength figure of merit to the case of an extremely clear atmosphere and draw several conclusions regarding the relative merits of fundamental-second harmonic, fundamental-third harmonic, second-third harmonic, and Raman two color systems. We find that, in spite of the larger dispersion between wavelengths, fundamental-third harmonic systems have the lowest figure of merit due to a combination of poor detector performance at the fundamental and poor atmospheric transmission at the third harmonic. The fundamental-second harmonic systems (approximately 700 nm and 350 nm) have the highest figure of merit, but second-third harmonic systems, using fundamental transmitters near 1000 nm, are a close second. Raman-shifted transmitters appear to offer no advantage over harmonic systems because of the relatively small wavelength separation that can be achieved in light gases such as hydrogen and the lack of good ultrashort pulse transmitters with an optimum fundamental wavelength near 400 nm.

Degnan, John J.↗

Thermal Electron Contributions to Current-Driven Instabilities: SCIFER Observations in the 1400-km Cleft Ion Fountain and Their Implications to Thermal Ion Energization

SCIFER TECHS observations of the variations in the thermal electron distribution in the 1400-km altitude cleft are associated with periods of intense ion heating and field-aligned currents. Energization of the thermal ion plasma in the mid-altitude cleft occurs within density cavities accompanied by enhanced thermal electron temperatures, large field-aligned thermal electron plasma flows and broadband low-frequency electric fields. Variations in the thermal electron contribution to field-aligned current densities indicate small scale (approximately 100's m) filamentary structure embedded within the ion energization periods. TECHS observations of the field-aligned drift velocities and temperatures of the thermal electron distribution are presented to evaluate the critical velocity thresholds necessary for the generation of electrostatic ion cyclotron and ion acoustic instabilities. This analysis suggests that, during periods of thermal ion energization, sufficient drift exists in the thermal electron distribution to excite the electrostatic ion cyclotron instability. In addition, brief periods exist within the same interval where the drift of the thermal electron distribution is sufficient to marginally excite the ion acoustic instability. In addition, the presence an enhancement in Langmuir emission at the plasma frequency at the center of the ion energization region, accompanied by the emission's second-harmonic, and collocated with observations of high-frequency electric field solitary structures suggest the presence of electron beam driven decay of Langmuir waves to ion acoustic modes as an additional free energy source for ion energization.

Adrian, Mark L.↗

NASA Tech Briefs, December 2010

Topics include: Coherent Frequency Reference System for the NASA Deep Space Network; Diamond Heat-Spreader for Submillimeter-Wave Frequency Multipliers; 180-GHz I-Q Second Harmonic Resistive Mixer MMIC; Ultra-Low-Noise W-Band MMIC Detector Modules; 338-GHz Semiconductor Amplifier Module; Power Amplifier Module with 734-mW Continuous Wave Output Power; Multiple Differential-Amplifier MMICs Embedded in Waveguides; Rapid Corner Detection Using FPGAs; Special Component Designs for Differential-Amplifier MMICs; Multi-Stage System for Automatic Target Recognition; Single-Receiver GPS Phase Bias Resolution; Ultra-Wideband Angle-of-Arrival Tracking Systems; Update on Waveguide-Embedded Differential MMIC Amplifiers; Automation Framework for Flight Dynamics Products Generation; Product Operations Status Summary Metrics; Mars Terrain Generation; Application-Controlled Parallel Asynchronous Input/Output Utility; Planetary Image Geometry Library; Propulsion Design With Freeform Fabrication (PDFF); Economical Fabrication of Thick-Section Ceramic Matrix Composites; Process for Making a Noble Metal on Tin Oxide Catalyst; Stacked Corrugated Horn Rings; Refinements in an Mg/MgH2/H2O-Based Hydrogen Generator; Continuous/Batch Mg/MgH2/H2O-Based Hydrogen Generator; Strain System for the Motion Base Shuttle Mission Simulator; Ko Displacement Theory for Structural Shape Predictions; Pyrotechnic Actuator for Retracting Tubes Between MSL Subsystems; Surface-Enhanced X-Ray Fluorescence; Infrared Sensor on Unmanned Aircraft Transmits Time-Critical Wildfire Data; and Slopes To Prevent Trapping of Bubbles in Microfluidic Channels.

Source record↗

Preliminary Assessment of the Interior Noise Environment in the Large Civil Tiltrotor (LCTR2)

The second-generation Large Civil Tiltrotor (LCTR2) serves as a representative vehicle under the NASA Fundamental Aeronautics Program (FAP) Subsonic Rotary Wing (SRW) project with a design goal to transport 90 passengers over a distance of 1800 km at a speed of 550 km/hr. The tiltrotor combines the vertical lift capability of a helicopter with the speed, altitude, and range of a turboprop airplane. The blade-passage frequency of the four-bladed rotor is as low as 6.9 Hz during cruise conditions. The resulting low-frequency acoustic excitation and its harmonics, combined with the anticipated use of lightweight composite and sandwich materials for the fuselage sidewall, may pose a challenge to achieving acceptable interior noise levels. The objective of the present study is to perform a preliminary assessment of the expected interior noise environment in the LCTR2 cabin. The approach includes a combination of semi-empirical, analytical, and statistical energy analysis methods. Because the LCTR2 is a notional vehicle, the prediction approach was also applied to the XV-15 tiltrotor and Bombardier Q400 turobprop aircraft to compare predictions with publicly available experimental data. Guidance for the expected interior noise levels in the LCTR2 was obtained by considering both the predicted exterior noise levels and the transmission loss of a basic fuselage sidewall consisting of a skin, porous layer and a trim panel. Structural and acoustic resonances are expected to coincide with low order harmonics of the blade passage frequency. The estimated sound pressure levels in the LCTR2 may not be acceptable when evaluated against known characteristics of human response to low frequency sound.

Grosveld, Ferdinand W.↗

Modeling of the Coupled Magnetospheric and Neutral Wind Dynamos

Over the past four years of funding, SRI, in collaboration with the University of Texas at Dallas, has been involved in assessing the influence of thermospheric neutral winds on the electric field and current systems at high latitudes. The initial direction of the project was to perform a set of numerical experiments concerning the contribution of the magnetospheric and neutral wind dynamo processes, under specific boundary conditions, to the polarization electric field and/or the field-aligned current distribution at high latitudes. To facilitate these numerical experiments we developed a numerical scheme that relied on using output from the NCAR Thermosphere-Ionosphere General Circulation Model (NCAR-TIGCM), expanding them in the form of spherical harmonics and solving the dynamo equations spectrally. Once initial calculations were completed, it was recognized that the neutral wind contribution could be significant but its actual contribution to the electric field or currents depended strongly on the generator properties of the magnetosphere. Solutions to this problem are not unique because of the unknown characteristics of the magnetospheric generator, therefore the focus was on two limiting cases. One limiting case was to consider the magnetosphere as a voltage generator delivering a fixed voltage to the high-latitude ionosphere and allowing for the neutral wind dynamo to contribute only to the current system. The second limiting case was to consider the magnetosphere as a current generator and allowing for the neutral wind dynamo to contribute only to the generation of polarization electric fields. This work was completed and presented at the l994 Fall AGU meeting. The direction of the project then shifted to applying the Poynting flux concept to the high-latitude ionosphere. This concept was more attractive as it evaluated the influence of neutral winds on the high-latitude electrodynamics without actually having to determine the generator characteristics of the magnetosphere. The influence of the neutral wind was then determined not by estimating how much electric potential or current density it provides, but by determining the contribution of the neutral wind to the net electromagnetic energy transferred between the ionosphere and magnetosphere. The estimate of the net electromagnetic energy transfer and the role of the neutral winds proves to be a more fundamental quantity in studies of magnetosphere- ionosphere coupling also showed that by using electric and magnetic field measurements from the HILAT satellite, the Poynting flux could be a measurable quantity from polar-orbiting, low- altitude spacecraft. Through collaboration with Dr. Heelis and others at UTD and their expertise of the electric field measurements on the DE-B satellite, an extensive analysis was planned to determine the Poynting flux from the DE-B measurements in combination with a modeling effort to help interpret the observations taking into account the coupled magnetosphere-ionosphere.

Thayer, Jeffrey P.↗

Non-linear propagation of complex sound fields in rectangular ducts. I - The self-excitation phenomenon

Nonlinear acoustic interactions at the second order (so-called weak interactions) of the perturbation scheme have been recognized for a long time. This paper examines the possibility of stronger interactions at the first order which are found in rigid rectangular ducts and to a lesser degree in slightly soft rectangular ducts. The strong interactions occur if any two modes have identical phase speeds, the case of multimode and multifrequency input for example. An important consequence of the strong interaction is the self-generation of subharmonics. Even a small amount of subharmonic can, given the right phase conditions, grow through a strong interaction with a higher harmonic.

Vaidya, P. G.↗

Electron cyclotron harmonic waves observed by the AMPTE-IRM plasma wave experiment following a lithium release in the solar wind

An unexpected occurrence following the second lithium release by the AMPTE-IRM spacecraft in the solar wind on September 20, 1984, was the appearance of electron cyclotron harmonic emissions. These emissions began about 50 s after the release and continued for several minutes. Narrow-band emissions polarized perpendicular to the magnetic field with amplitudes of approximately 0.00001 V/m were observed in each of the first five harmonic bands. The diffuse emissions extended from below the lowest measured frequency channel to above the highest narrow-band emission with a maximum below the electron cyclotron frequency. It will be shown that these observations are inconsistent with their generation by several ion beam instabilities.

Roeder, J. L.↗

Enhancements to the SSME transfer function modeling code

This report details the results of a one year effort by Ohio University to apply the transfer function modeling and analysis tools developed under NASA Grant NAG8-167 (Irwin, 1992), (Bartholomew, 1992) to attempt the generation of Space Shuttle Main Engine High Pressure Turbopump transfer functions from time domain data. In addition, new enhancements to the transfer function modeling codes which enhance the code functionality are presented, along with some ideas for improved modeling methods and future work. Section 2 contains a review of the analytical background used to generate transfer functions with the SSME transfer function modeling software. Section 2.1 presents the 'ratio method' developed for obtaining models of systems that are subject to single unmeasured excitation sources and have two or more measured output signals. Since most of the models developed during the investigation use the Eigensystem Realization Algorithm (ERA) for model generation, Section 2.2 presents an introduction of ERA, and Section 2.3 describes how it can be used to model spectral quantities. Section 2.4 details the Residue Identification Algorithm (RID) including the use of Constrained Least Squares (CLS) and Total Least Squares (TLS). Most of this information can be found in the report (and is repeated for convenience). Section 3 chronicles the effort of applying the SSME transfer function modeling codes to the a51p394.dat and a51p1294.dat time data files to generate transfer functions from the unmeasured input to the 129.4 degree sensor output. Included are transfer function modeling attempts using five methods. The first method is a direct application of the SSME codes to the data files and the second method uses the underlying trends in the spectral density estimates to form transfer function models with less clustering of poles and zeros than the models obtained by the direct method. In the third approach, the time data is low pass filtered prior to the modeling process in an effort to filter out high frequency characteristics. The fourth method removes the presumed system excitation and its harmonics in order to investigate the effects of the excitation on the modeling process. The fifth method is an attempt to apply constrained RID to obtain better transfer functions through more accurate modeling over certain frequency ranges. Section 4 presents some new C main files which were created to round out the functionality of the existing SSME transfer function modeling code. It is now possible to go from time data to transfer function models using only the C codes; it is not necessary to rely on external software. The new C main files and instructions for their use are included. Section 5 presents current and future enhancements to the XPLOT graphics program which was delivered with the initial software. Several new features which have been added to the program are detailed in the first part of this section. The remainder of Section 5 then lists some possible features which may be added in the future. Section 6 contains the conclusion section of this report. Section 6.1 is an overview of the work including a summary and observations relating to finding transfer functions with the SSME code. Section 6.2 contains information relating to future work on the project.

Irwin, R. Dennis↗