SEARCH · Search NASA

Results for “sideslip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Stability and control of a supersonic transport airplane during landing approach

Modal control theory was applied to determine feedback gains that provide desirable stability characteristics and satisfactory transient response to aileron deflection input. However, the peak value of lateral acceleration at the pilot's station does not satisfy a proposed criterion during a rolling maneuver. Optimal regulator theory does not provide a significant reduction of the peak lateral acceleration. The weighting matrices in the performance index were given an extreme variation, but the effect on lateral acceleration remained insignificant. Open loop control provided the desired bank angle (30 deg) with the desired roll rate (10 deg/sec), and provided a satisfactory level of lateral acceleration. However, a large adverse sideslip angle was required. In addition, the yawing velocity was negative for about two seconds and lateral acceleration changed sign during the maneuver. The problem persists and perhaps relaxed criteria must be proposed. The criteria could allow any combination of a lower average rolling velocity, a larger adverse sideslip angle excursion, and a higher peak lateral acceleration at the pilot's station.

Oehman, W. I.↗

NASA NTRS1983

Pressure distributions obtained on a 0.04-scale and 0.02-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley continuous flow hypersonic tunnel

Results from pressure distribution tests on 0.04-scale and 0.02-scale models of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests wre completed in the Langley Continuous Flow Hypersonic Tunnel (CFHT). The 0.04-scale model was tested at angles of attack from -5 deg to 45 deg and angles of sideslip from -3 deg to 3 deg. The 0.02-scale model was tested at angles of attack from -10 deg to 45 deg and angles of sideslip from -5 deg to 5 deg. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel models were also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation has provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗

NASA NTRS1983

Pressure distributions obtained on a 0.04-scale and 0.02-scale model of the Space Shuttle Orbiter's forward fuselage in the Langley 20-inch Mach 6 air tunnel

Results from pressure distribution tests on 0.04-scale and 0.02-scale models of the forward fuselage of the Space Shuttle Orbier are presented without analysis. The tests were completed in the Langley 20-Inch Mach 6 Tunnel. The 0.04-scale model was tested at angles of attack from 0 to 35 and angles of sideslip from 0 to -4. The 0.02-scale model was tested at angles of attack from -10 to 45 and angles of sideslip from 0 to -4. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS pressure orifices, the wind-tunnel to models were also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations currently existing on the Space Shuttle Orbiter Columbia (OV-102). This DFI simulation had provided a means for comparisons between reentry flight pressure data and wind-tunnel data.

Bradley, P. F.↗

NASA NTRS1983

An experimental heat-transfer investigation of an advanced winged entry vehicle at Mach 10

Heat-transfer measurements have been made at Mach 10 in air on an instrumented 0.006-scale model of an advanced winged entry vehicle. Data were obtained at 83 thermocouple stations which include locations on the lower and upper surface centerlines, spanwise positions along the lower and upper surfaces of the wing, the lower surface of the body flap, and radial locations on the fuselage. Data were obtained for angles of attack ranging from 0 to 45 deg, sideslip angles of + or - 2 deg, Reynolds numbers of 0.5, 1.0 and 2.0 million per foot, and body-flap deflections of 0, 10, and 20 deg. The data generally indicate increased windward heating and decreased leeside heating with increased angle of attack, significantly increased body-flap heating with deflection angle, and minor variations in heating with sideslip, increasing in magnitude with angle of attack. Windward centerline data are shown to be in fair agreement with results of predictions based on an approximate engineering method.

Wurster, K. E.↗

NASA NTRS1983

Subsonic roll oscillation experiments on the Standard Dynamics Model

The experimental determination of the subsonic roll derivatives of the Standard Dynamics Model, which is representative of a current fighter aircraft configuration, is described. The direct, cross and cross-coupling derivatives are presented for angles of attack up to 41 deg and sideslip angles in the range from -5 deg to 5 deg, as functions of oscillation frequency. The derivatives exhibited significant nonlinear trends at high incidences and were found to be extremely sensitive to sideslip angle at angles of attack near 36 deg. The roll damping and dynamic cross derivatives were highly frequency dependent at angles of attack above 30 deg. The highest values measured for the dynamic cross and cross-coupling derivatives were comparable in magnitude with the maximum roll damping. The effects of oscillation amplitude and Mach number were also investigated, and the direct derivatives were correlated with data from another facility.

Beyers, M. E.↗

NASA NTRS1982

Helistat simulation studies

An analysis of the flight dynamics and piloted control characteristics of the Helistat, a quadrotor heavy-lift airship, was completed using the HYBRDS airship simulation facility. The analysis covered the full operating flight envelope, including likely ranges of altitude, airspeed, sideslip, and loading variations. Particular areas of study were performance, trim, power requirements, linearized dynamics, handling qualities, and mooring operations. The key assumptions were: a rigid vehicle, no control system dynamics, fixed rotor and propeller RPM, and no ballonet dynamics. The nominal cruise speed for the H34 engines operating at 1275 HP was found to be 40-50 kts, depending on the loading condition. The maximum payload capability was calculated as 45,000 lbs for sea level-based operations. The crosswind capability in hover is 5-10 kts depending on the loading conditions, but this requires excessive roll angle due to the roll-to-translate control gearing. Sideslip angles of 110-135 degrees (wind from aft quarters) are critical for directional trim and stability, and should be avoided.

Tischler, M. B.↗

NASA NTRS1984

Doppler radiation sensing of Shuttle angle of attack and TAS during entry

Space Shuttle true airspeed, angle of attack, and sideslip angle are currently derived from inertial guidance information. A new method is proposed which offers a potential improvement in Shuttle safety during entry. Angle of attack, sideslip angle and true airspeed could be measured directly at heights from 120 km down to 20 km by Doppler sensing three independent true airspeeds along the Shuttle body axes. Two types of Doppler measurement sensors, employing either passive detection of atmospheric radiation or coherent detection of scattered laser light are discussed. The proposed technique is essentially solid-state and robust, and is well suited for use in future small hypersonic vehicles that require flight control in the Upper Atmosphere of the earth or in probes destined for the other planets.

Foale, C. M.↗

NASA NTRS1983

Oil-flow study of a Space Shuttle orbiter tip-fin controller

Possible use of tip-fin controllers instead of a vertical tail on advanced winged entry vehicles was examined. Elimination of the vertical tail and using tip-fins offers the advantages of positive yaw control at high angles of attack and a potential weight savings. Oil-flow technique was used to obtain surface flow patterns on a tip-fin installed on a 0.01-scale Space Shuttle orbiter model for the purpose of assessing the extent of flow interference effects on the wing and tip-fin which might lead to serious heating problems. Tests were conducted in air at Mach 10 for a free-stream Reynolds numbers of .000113 at 20, 30, and 40 degree angle of attack and sideslip angles of 0 and 2 degree. Elevon deflections of -10, 0, and 10 degree and tip-fin control-surface deflections of 0, 20, and 40 degree were employed. Test results were also used to aid in the interpretation of heating data obtained on a Shuttle orbiter tip-fin on another model in a different facility. A limited comparison of oil-flow patterns and heat-transfer data is included. It was determined that elevon deflection angles from -10 to 10 degree and sideslip angles up to 2 degree have very little effect on tip-fin surface flow patterns. Also, there is a minimum of interference between the tip-fin and the wing. The most significant flow interactions occur on the tip-fin onboard surface as a result of its control-surface deflections.

Helms, V. T., III↗

NASA NTRS1985

Low-speed experimental study of the vortex flow effects of a fighter forebody having unconventional cross-section

A low speed wind tunnel investigation is conducted for the vortex flow characteristics of a tailless fighter configuration that features full length, fuselage-blended forebody strakes. Static pressure distributions were obtained on the forebody upper surface, and six-component forces and moments were measured on the complete, 60-deg cropped delta wing-fuselage-centerline vertical fin model at angles of attack and sideslip respectively reaching 50 deg and + or - 20 deg. The surface pressure data reveal that development of concentrated vortices from the sharp edged forebody strakes occurred at moderate and high angles of attack. The blended forebody was effective in capturing the windward vortical flow up to high incidence and sideslip angles. The direct suction effect of the windward vortex on the forebody sidewall was the primary contributor to static directional stability at high angles of attack. These improvements are potentially offset, however, by reduced or unstable roll and yaw damping.

Erickson, G. E.↗

NASA NTRS1986

Natural laminar flow flight experiments on a swept wing business jet-boundary layer stability analyses

The linear boundary layer stability analyses and their correlation with data of 18 cases from a natural laminar flow (NLF) flight test program using a Cessna Citation 3 business jet are described. The transition point varied from 5% to 35% chord for these conditions, and both upper and lower wing surfaces were included. Altitude varied from 10,000 to 43,000 ft and Mach number from 0.3 to 0.8. Four cases were at nonzero sideslip. Although there was much scatter in the results, the analyses of boundary layer stability at the 18 conditions led to the conclusion that crossflow instability was the primary cause of transition. However, the sideslip cases did show some interaction of crossflow and Tollmien-Schlichting disturbances. The lower surface showed much lower Tollmien-Schlichting amplification at transition than the upper surface, but similar crossflow amplifications. No relationship between Mach number and disturbance amplification at transition could be found. The quality of these results is open to question from questionable wing surface quality, inadequate density of transition sensors on the wing upper surface, and an unresolved pressure shift in the wing pressure data. The results of this study show the need for careful preparation for transition experiments. Preparation should include flow analyses of the test surface, boundary layer disturbance amplification analyses, and assurance of adequate surface quality in the test area. The placement of necessary instruments and usefulness of the resulting data could largely be determined during the pretest phase.

Rozendaal, R. A.↗

NASA NTRS1986

Influence of forebody cross-sectional shape on wing vortex burst location

A water tunnel study examining the influence of forebody cross section on the position of the wing vortex burst was carried out in the NASA Ames-Dryden water tunnel for a 55-deg cropped delta-wing model. Two of three cross sections investigated were chine-shaped, where the included angle of the chine was either 7.5-deg, representing a rather small side-edge angle, or 90 deg, representing a more moderate design. The third cross section was circular and served as a baseline for comparison. It is found that the 7.5 deg chine cross section generated the strongest forebody vortices of the three configurations and that these strong forebody vortices interacted with the main wing vortices in such a manner as to dramatically delay wing vortex burst position at zero sideslip. If the configuration is sideslipped, large asymmetries in wing vortex burst location may result.

Hall, R. M.↗

NASA NTRS1987

Top-mounted inlet performance for a V/STOL fighter/attack aircraft configuration

Inlet flow-field and compressor-face performance data were obtained for a 0.095-scale model of vertical/short take-off landing (V/STOL) fighter/attack aircraft configuration with twin top-mounted inlets. Tests were conducted at Mach numbers from 0.6 to 2.0 and angles of attack and sideslip up to 27 deg. and 12 deg., respectively. Reynolds number was held constant at 9.8 x 10 to the 6th power per meter. The effects of inlet location, wing leading-edge extension (LEX) planform area, canopy-dorsal integration, variable incidence canards, and wing leading- and trailing-edge flap deflections were determined. The results show that at Mach numbers up to 0.9, distortion is relatively low (20% or less) at all angles of attack and sideslip. However, at Mach numbers of 1.2 and above, operation may be restricted because of either high distortion or low pressure recovery (80% or less), or both. These difficulties may be overcome with alterations to the LEX/canopy/body juncture.

Smeltzer, Donald B.↗

NASA NTRS1987

Qualitative evaluation of a flush air data system at transonic speeds and high angles of attack

Flight tests were performed on an F-14 aircraft to evaluate the use of flush pressure orifices on the nose section for obtaining air data at transonic speeds over a large range of flow angles. This program was part of a flight test and wind tunnel program to assess the accuracies of such systems for general use on aircraft. It also provided data to validate algorithms developed for the shuttle entry air data system designed at NASA Langley. Data were obtained for Mach numbers between 0.60 and 1.60, for angles of attack up to 26.0 deg, and for sideslip angles up to 11.0 deg. With careful calibration, a flush air data system with all flush orifices can provide accurate air data information over a large range of flow angles. Several orificies on the nose cap were found to be suitable for determination of stagnation pressure. Other orifices on the nose section aft of the nose cap were shown to be suitable for determination of static pressure. Pairs of orifices on the nose cap provided the most sensitive measurements for determining angles of attack and sideslip, although orifices located farther aft on the nose section could also be used.

Larson, Terry J.↗

NASA NTRS1987

A piloted simulation of helicopter air combat to investigate effects of variations in selected performance and control response characteristics

A piloted simulation study investigating handling qualities and flight characteristics required for helicopter air to air combat is presented. The Helicopter Air Combat system was used to investigate this role for Army rotorcraft. Experimental variables were the maneuver envelope size (load factor and sideslip), directional axis handling qualities, and pitch and roll control-response type. Over 450 simulated, low altitude, one-on-one engagements were conducted. Results from the experiment indicate that a well damped directional response, low sideforce caused by sideslip, and some effective dihedral are all desirable for weapon system performance, good handling qualities, and low pilot workload. An angular rate command system was favored over the attitude type pitch and roll response for most applications, and an enhanced maneuver envelope size over that of current generation aircraft was found to be advantageous. Pilot technique, background, and experience are additional factors which had a significant effect on performance in the air combat tasks investigated. The implication of these results on design requirements for future helicopters is presented.

Lewis, Michael S.↗

NASA NTRS1987

Investigation of a delta-wing fighter model flow field at transonic speeds

The paper reports a flow-field investigation on a 7.52-percent scale model of an advanced fighter aircraft design conducted in the NASA-Langley 16-ft Transonic Tunnel. The effects of free-stream Mach number, angle-of-attack, angle of sideslip, and various vortex control devices on the local flow values were studied. The model was tested at Mach numbers of 0.6, 0.9, and 1.2 and the angles of sideslip of 0 and +/- 5 deg; the model angle-of-attack was varied from -4 to 30 deg. Results are presented in terms of contour plots of local total pressure recovery. The dominant influence on the over-wing flow field was found to be the wing leading-edge vortex which first appears in the survey region at an angle-of-attack of 8 deg and increases in strength and influence with increasing angle-of-attack, finally dominating the entire survey region at very high angles-of-attack.

Bare, E. Ann↗

NASA NTRS1988

The effects of RCS jet firing on the isolated Orbiter and mated coast phases of the glide return to launch site maneuver at Mach number 6 (IA302B)

An updated Space Shuttle aerodynamic data base was obtained in Tunnel B for two phases of the Glide Return to Launch Site (GRTLS) abort maneuver. One-and-a-quarter percent scale models of the Space Shuttle Orbiter and External Tank were used to measure the effects of various combinations of Reaction Control System (RCS) jet thrusters at Mach number 6. The angle-of-attack range for the isolated orbiter was -10 to 15 deg at sideslip angles from -5 to 10 deg during Phase 1 of testing. The angle-of-attack range for the mated orbiter and external tank was -5 to 15 deg with sideslip angles of -2 to 5 deg during Phase 2. The test was conducted at a unit Reynolds number of 0.75 million per foot.

Garrett, L. V.↗

NASA NTRS1987

An analysis of a candidate control algorithm for a ride quality augmentation system

This paper presents a detailed analysis of a candidate algorithm for a ride quality augmentation system. The algorithm consists of a full-state feedback control law based on optimal control output weighting, estimators for angle of attack and sideslip, and a maneuvering algorithm. The control law is shown to perform well by both frequency and time domain analysis. The rms vertical acceleration is reduced by about 40 percent over the whole mission flight envelope. The estimators for the angle of attack and sideslip avoid the often inaccurate or costly direct measurement of those angles. The maneuvering algorithm will allow the augmented airplane to respond to pilot inputs. The design characteristics and performance are documented by the closed-loop eigenvalues; rms levels of vertical, lateral, and longitudinal acceleration; and representative time histories and frequency response.

Suikat, Reiner↗

NASA NTRS1989

In-flight measurement of propeller noise on the fuselage of an airplane

In-flight measurements of propeller noise on the fuselage of an OV-10A aircraft were obtained using a horizontal and a vertical microphone array. A wide range of flight conditions were tested including changes in angle of attack, sideslip angle, power coefficient, helical tip Mach number and advance ratio, and propeller direction of rotation. Results show a dependence of the level and directivity of the tones on the angle of attack and on the sideslip angle with the propeller direction of rotation, which is similar to results obtained in wind tunnel tests with advanced propeller designs. The level of the tones at each microphone increases with increasing angle of attack for inboard-down propeller rotation and decreases for inboard-up rotation. The level also increases with increasing slideslip angle for both propeller directions of rotation. Increasing the power coefficient results in a slight increase in the level of the tones. A strong shock wave is generated by the propeller blades even at relatively low helical tip Mach numbers resulting in high harmonic levels. As the helical tip Mach number and the advance ratio are increased, the level of the higher harmonics increases much faster than the level of the blade passage frequency.

Pla, Frederic G.↗