Search NASA⌕ Search

SEARCH · Search NASA

Results for “soil structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

The SMAP Level 4 Surface and Root-zone Soil Moisture (L4_SM) Product

The Soil Moisture Active and Passive (SMAP) mission is being developed by NASA for launch in 2013 as one of four first-tier missions recommended by the U.S. National Research Council Committee on Earth Science and Applications from Space in 2007. The primary science objectives of SMAP are to enhance understanding of land surface controls on the water, energy and carbon cycles, and to determine their linkages. Moreover, the high resolution soil moisture mapping provided by SMAP has practical applications in weather and seasonal climate prediction, agriculture, human health, drought and flood decision support. In this paper we describe the assimilation of SMAP observations for the generation of the planned SMAP Level 4 Surface and Root-zone Soil Moisture (L4_SM) product. The SMAP mission makes simultaneous active (radar) and passive (radiometer) measurements in the 1.26-1.43 GHz range (L-band) from a sun-synchronous low-earth orbit. Measurements will be obtained across a 1000 km wide swath using conical scanning at a constant incidence angle (40 deg). The radar resolution varies from 1-3 km over the outer 70% of the swath to about 30 km near the center of the swath. The radiometer resolution is 40 km across the entire swath. The radiometer measurements will allow high-accuracy but coarse resolution (40 km) measurements. The radar measurements will add significantly higher resolution information. The radar is however very sensitive to surface roughness and vegetation structure. The combination of the two measurements allows optimal blending of the advantages of each instrument. SMAP directly observes only surface soil moisture (in the top 5 cm of the soil column). Several of the key applications targeted by SMAP, however, require knowledge of root zone soil moisture (approximately top 1 m of the soil column), which is not directly measured by SMAP. The foremost objective of the SMAP L4_SM product is to fill this gap and provide estimates of root zone soil moisture that are informed by and consistent with SMAP observations. Such estimates are obtained by merging SMAP observations with estimates from a land surface model in a soil moisture data assimilation system. The land surface model component of the assimilation system is driven with observations-based surface meteorological forcing data, including precipitation, which is the most important driver for soil moisture. The model also encapsulates knowledge of key land surface processes, including the vertical transfer of soil moisture between the surface and root zone reservoirs. Finally, the model interpolates and extrapolates SMAP observations in time and in space. The L4_SM product thus provides a comprehensive and consistent picture of land surface hydrological conditions based on SMAP observations and complementary information from a variety of sources. The assimilation algorithm considers the respective uncertainties of each component and yields a product that is superior to satellite or model data alone. Error estimates for the L4_SM product are generated as a by-product of the data assimilation system.

Reichle, Rolf↗
NASA NTRS1974

The crystal chemistry of armalcolites from Apollo 17

Single-crystal X-ray studies of armacolites from the 2 to 5 mm fraction of Apollo 17 soils 75082 and 78502 are evaluated. The two types of armacolites studied show slight composition differences and identical structures. Precession photographs of each crystal show the two forms, ortho and para, to have the same space group and nearly the same cell dimensions. The analyses conducted support the proposition that the difference in optical properties is caused by differing MgO and Cr2O3 contents.

Smyth, J. R.↗
NASA NTRS1980

The High Visible Resolution (HVR) instrument of the spot ground observation satellite

Two identical high resolution cameras, capable of attaining a track width of 116 km in an almost vertical line of sight from the two 60 km images of each instrument, will be carried on the initial mission of the space observation of Earth satellite (SPOT). Specifications for the instrument, including the telescope and CCD devices are summarized. The present status of development is described including the optical characteristics, structure and thermal control, detector assembly, electronic equipment, and calibration. SPOT mission objectives include the developments relating to soil use, the exploration of EART Earth resources, the discrimination of plant species, and cartography.

Otrio, G.↗
NASA NTRS1986

Crystalline-silicon photovoltaics summary module design and reliability

The evolution of the design and reliability of solar modules was described. Design requirements involved 14 different considerations, including residential building and material electrical codes, wind-loading, hail impact, operating temperature levels, module flammability, and interfaces for both the array structure and the operation of the system. Reliability research involved in diverse investigations including glass-fracture strength, soiling levels, electrochemical corrosion, and bypass-diode qualification tests. Based on these internationally recognized studies, performance assessments, and failure analyses, the Flat-plate Solar Array Project in its 11-year duration served to nuture the development of 45 different solar module designs from 15 PV manufacturers.

Ross, R. G., Jr.↗
NASA NTRS1990

Engineering, construction, and operations in space II; Proceedings of Space 90, the Second International Conference, Albuquerque, NM, Apr. 22-26, 1990. Vols. 1 & 2

Attention is given to such topics as the processing of lunar soils, the automated processing of extraterrestrial materials, lunar excavation and mining, lunar oxygen, lunar base development, lunar surface structures, planetary surface transportation, and Mars missions. Papers are also presented on the Space Station, space debris, robotics and automated processing, structures and structural response, Mission to Planet Earth, life support systems, space power, human factors, artificial gravity, and education.

Johnson, Stewart W.↗
NASA NTRS2005

Extracting Olivine (Fo-Fa) Compositions from Raman Spectral Peak Positions

Olivine and pyroxene are two major basaltic minerals that have been identified at Gusev Crater and Meridiani Planum by the Mars Exploration Rovers. Full petrologic characterization of a sample (rock or soil), however, requires determining the range of mineral compositions, extent of zoning, range of grain sizes, mineral associations, presence of xenocrysts, etc. Information of this sort will aid the interpretation of sample crystallization and differentiation histories and help discriminate between lithologies. In Raman spectroscopic experiments, minerals are identified by their spectral patterns and mineral compositions can be inferred from the peak positions. Instruments currently in use or slated for impending surface exploration missions provide only average elemental compositions for relatively large rock or soil targets or bulk mineral analysis. No techniques currently in use or scheduled for flight can characterize both structure and composition of individual mineral grains, in-situ, like the Mars Microbeam Raman Spectrometer (MMRS). The MMRS is designed to take 100 spectra along a 1 cm linear traverse on the surface of a sample, with contributions from one or a few mineral phases per spectrum. We presented a method to extract structural and compositional information from the Raman spectra of quadrilateral pyroxenes. The pyroxene calibration was applied to a Raman spectroscopic study of Martian meteorite EETA79001 along with a preliminary olivine calibration, where we demonstrated the capability to discriminate related lithologies using Raman point counts. This paper presents an improved olivine calibration that will further aid sample characterization and the study of alteration processes.

Kuebler, K.↗
NASA NTRS2012

Incorporating Plant Phenology Dynamics in a Biophysical Canopy Model

The Multi-Layer Canopy Model (MLCan) is a vegetation model created to capture plant responses to environmental change. Themodel vertically resolves carbon uptake, water vapor and energy exchange at each canopy level by coupling photosynthesis, stomatal conductance and leaf energy balance. The model is forced by incoming shortwave and longwave radiation, as well as near-surface meteorological conditions. The original formulation of MLCan utilized canopy structural traits derived from observations. This project aims to incorporate a plant phenology scheme within MLCan allowing these structural traits to vary dynamically. In the plant phenology scheme implemented here, plant growth is dependent on environmental conditions such as air temperature and soil moisture. The scheme includes functionality that models plant germination, growth, and senescence. These growth stages dictate the variation in six different vegetative carbon pools: storage, leaves, stem, coarse roots, fine roots, and reproductive. The magnitudes of these carbon pools determine land surface parameters such as leaf area index, canopy height, rooting depth and root water uptake capacity. Coupling this phenology scheme with MLCan allows for a more flexible representation of the structure and function of vegetation as it responds to changing environmental conditions.

environmental changes↗
NASA NTRSDate not supplied

Lunar Lander Landing Modeling and Simulation in Simscape

The landing gear is a critical subsystem of a lander for a successful landing on the moon or a planet. During a landing event, structural loading, energy absorption and toppling stability are important factors for the landing gear development. These aspects can be studied using simulations. The landing gear comprising the primary struct, secondary structs, footpad, and joints, is easily modeled using Simscape Multibody toolbox. The energy absorption mechanisms in the structs is readily modeled using Simulink and Multibody blocks based on the relative motions of the inner and outer cylinder of the structures. During touchdown, the footpads strike the lunar surface, and the contact forces can be modeled including the soil mechanical properties. Slosh dynamics are included using a mechanical pendulum model. Tip-over controllers are developed using Simulink blocks and toolboxes. This model was intensively tested manually then additionally with Monte Carlo simulation. It offers the opportunity for landing stability study, i.e. the max slope a lander can land without tipping over in 3D realistic landing situations.

Wei Wu↗
NASA NTRS2018

Soil Water Content Effects on Net Ecosystem CO2 Exchange and Actual Evapotranspiration in a Mediterranean Semiarid Savanna of Central Chile

Biosphere-atmosphere water and carbon fluxes depend on ecosystem structure, and their magnitudes and seasonal behavior are driven by environmental and biological factors. We studied the seasonal behavior of net ecosystem CO2 exchange (NEE), Gross Primary Productivity (GPP), Ecosystem Respiration (RE), and actual evapotranspiration (ETa) obtained by eddy covariance measurements during two years in a Mediterranean Acacia savanna ecosystem (Acacia caven) in Central Chile. The annual carbon balance was −53 g C/sq. m in 2011 and −111 g C/sq. m in 2012, showing that the ecosystem acts as a net sink of CO2, notwithstanding water limitations on photosynthesis observed in this particularly dry period. Total annual ETa was of 128 mm in 2011 and 139 mm in 2012. Both NEE and ETa exhibited strong seasonality with peak values recorded in the winter season (July to September), as a result of ecosystem phenology, soil water content and rainfall occurrence. Consequently, the maximum carbon assimilation rate occurred in wintertime. Results show that soil water content is a major driver of GPP and RE, defining their seasonal patterns and the annual carbon assimilation capacity of the ecosystem, and also modulating the effect that solar radiation and air temperature have on NEE components at shorter time scales.

Meza, Francisco J.↗
NASA NTRS1986

AIS spectra of desert shrub canopies

Airborne Imaging Spectrometer (AIS) data were collected 30 August 1985 from a desert shrub community in central Oregon. Spectra from artificial targets placed on the test site and from bare soil, big sagebrush (Artemesia tridentata wyomingensis), silver sagebrush (Artemesia cana bolander), and exposed volcanic rocks were studied. Spectral data from grating position 3 (tree mode) were selected from 25 ground positions for analysis by Principal Factor Analysis (PFA). In this grating position, as many as six factors were identified as significant in contributing to spectral structure. Channels 74 through 84 (tree mode) best characterized between-class differences. Other channels were identified as nondiscriminating and as associated with such errors as excessive atmospheric absorption and grating positin changes. The test site was relatively simple with the two species (A. tridentata and A. cana) representing nearly 95% of biomass and with only two mineral backgrounds, a montmorillonitic soil and volcanic rocks. If, as in this study, six factors of spectral structure can be extracted from a single grating position from data acquired over a simple vegetation community, then AIS data must be considered rich in information-gathering potential.

Murray, R.↗
NASA NTRS2004

Water on Mars: Evidence from MER Mission Results

The Viking and the Mars Exploration Rover missions observed that the surface of Mars is encrusted by a thinly cemented layer, or "duricrust". Elemental analyzes at five sites on Mars show that these soils have sulfur content and chlorine content consistent with the presence of sulfates and halides as mineral cements. The soil is highly enriched in the salt-forming elements compared with rock. Analysis of the soil cementation indicates some features which may be evidence of liquid water. At both MER sites, duricrust textures revealed by the Microscopic Imager show features including the presence of fine sand-sized grains, some of which may be aggregates of fine silt and clay, surrounded by a pervasive light colored material that is associated with microtubular structures and networks of microfractures. Stereo views of undisturbed duricrust surfaces reveal rugged microrelief between 2-3 mm and minimal loose material. Comparisons of microscopic images of duricrust soils obtain before and after placement of the Mossbauer spectrometer indicate differing degrees of compaction and cementation. Two models of a transient water hypothesis are offered, a "top down" hypothesis that emphasizes the surface deposition of frost, melting and downward migration of liquid water and a "bottom up" alternative that proposes the presence of interstitial ice/brine, with the upward capillary migration of liquid water. The viability of both of these models ultimately hinges on the availability of seasonally transient liquid water for brief periods.

Landis, Geoffrey A.↗
NASA NTRS1994

Thermal-infrared remote sensing and Kirchhoff's Law. 1: Laboratory measurements

By the end of this century the Earth Observing System (EOS) will provide worldwide, thermal infrared, multispectral images of the Earth, presenting geologists with a new kind of remote sensing data for interpretation. Thus it has become essential to understand the spectral emittance behavior of terrestrial surface materials. Perhaps the most fundamental question to be answereed is the extent to which such materials follow Kirchhoff's law (epsilon = 1 -R) under laboratory and field conditions, especially when a sample displays a thermal gradient. We present the first rigorous quantitative comparison of directional and hemispherical reflectance and directional emittance of rock and soil samples in the laboratory, with thermal gradients induced by heating them from below and allowing them to radiate to a colder background. The results show that only an extemeley low density sample composed of fine particles sifted into a 'fairy castle' structure displays a thermal gradient steep enough within the infrared skin depth to cause significant (6%) departure from Kirchhoff's law. There is no detectable effect on the more normal terrestrial samples, such as soils and rocks measured in the laboratory, even when semitransparent coatings are involved. Thus both emittance and reflectance measurements can be used to calculate sample emissivity for most terrestrial surface materieals. However, the effect on Kirchhoffian behavior of different field environments, which may induce a steeper thermal gradient in particulate samples, has yet to be determined, and some low-density surface materials like newly fallen snow, frost, and efflorescent salts on playas have yet to be measured in emittance.

Salisbury, John W.↗
NASA NTRSDate not supplied

Analysis of a Landing System for Planetary Payloads Utilizing Passive Energy Absorbing Composite Structure

Delivery of a payload from space to a planetary surface currently requires the development of an application specific landing system to protect the payload from forces imparted during impact with the planet surface. Often, active energy attenuating systems such as retro-rockets, deployable parachutes, and airbags are utilized within these landing systems to reduce landing impact energy. Unfortunately, these active systems come at a cost; active energy attenuating systems are susceptible to system faults which may limit or completely negate their energy attenuating capability. Additionally, components needing to be stowed such as fuel, parachutes, and airbags increase design complexity, cost, and weight. To overcome these limitations, this study examines the potential of passive energy attenuation through energy absorbing structural design and composite materials to mitigate landing loads for small payload planetary delivery. Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted extensive research into developing energy absorbing structures and components for the attenuation of impact energy under various loading conditions including aircraft crash and spacecraft impact. The current study leverages this research to design a lightweight planetary delivery system which utilizes unique outer mold line (OML) geometry and passive energy absorbing structural design to limit landing loads across potential planetary surface environments. The OML geometry is designed to control impact orientation and provide self-righting capabilities for slopped impact surfaces. The internal structure is composed of composite material structures arranged to provide energy absorption which is robust to impact angle and impact velocity. The developed planetary delivery design concept will be evaluated using finite element (FE) model analysis. Simulations of landing impacts with representative soil surface environments will be used to characterize the energy absorbing capabilities of the landing system. Sensitivity of predicted impact force to landing environment, impact angle, and impact velocity will be assessed to identify capabilities and limitations of the initial structural design. Results will be used to determine the feasibility of a lightweight composite structure to passively absorb landing energy for robust planetary payload delivery.

Crashworthiness↗
NASA NTRS1981

The microwave radiometer spacecraft. A design study: Executive summary

A conceptual design was developed for a microwave radiometer spacecraft (MRS) using a large passive reflector, microwave radiometer, and advanced control concepts soil moisture mapping from microwave sensing for global crop forecasting. Mission requirements and tradeoffs were defined, and major subsystems (structural, electromagnetic surface, and attitude control) conceptually designed. An overview of the mission and a summary of the study results are presented.

Lovelace, U. M.↗
NASA NTRS1996

Galactic Cosmic-Ray-Produced Thermoluminescence Profiles in Meteorites Lunar Samples and a Terrestrial Analog

The long-term radiation shielding properties of common extraterrestrial materials are poorly known, although these materials are the most likely structural elements on airless worlds such as the Moon. We report on radiation dose profiles in meteorites and lunar soil cores using specific minerals as naturally-occurring "dosimeters". We find that radiation profiles are fairly flat in typical meteoroid bodies (less than 85 cm radius) and drop by only about 40% through about 2.5 m of lunar soil. These profiles are produced by primary galactic cosmic rays and the secondary proton cascade but with a significant contribution by secondary neutrons at depths of about 2 m (300 g/sq cm).

Benoit, Paul H.↗
NASA NTRS2018

The Composition of Amorphous Phases in Soils and Sediments on Earth and Mars

Amorphous phases are major components (~15-70 wt%) of all rock and soil samples measured thus far by the CheMin X-ray diffractometer (XRD) instrument on the MSL rover in Gale crater, Mars. The nature of these phases is not well understood and could be any combination of primary (e.g., glass) and secondary (e.g., silica, errihydrite) phases. Secondary amorphous phases are frequently found as weathering products in soils on Earth, but these materials remain poorly characterized, and it is not certain how properties like composition and structure change with formation environment.

Smith, R. J.↗
NASA NTRS1973

Application of ERTS-1 imagery to detecting and mapping modern erosion features and to monitoring erosional changes, in southern Arizona

The author has identified the following significant results. The chief results during the reporting period were three 1:1,000,000 scale maps made from one ERTS-1 frame (1085-17330, 16 October 1972) showing: (1) the three most important types of materials in terms of the modern erosion problem: the readily erodible soils, gravel piedmonts and basin-fill areas, and consolidated rocks; (2) alluvial fans (dissected and relatively undissected); and (3) (as an additional bonus) linear structural features. Eight key areas (small parts of the whole study area) were selected for detailed study, and mapping was started in two of them, by interpretation of ultrahigh (U-2 and RB-57) airphotos, supplemented by field studies. In these areas detailed mapping was done not only on the modern erosion phenomena (arroyos, gullies, modern flood plains and terraces, and areas of sheet erosion and deposition), but also other features pertinent to the erosion problem, such as slope-local relief, landforms rock units, soil particle size and erodibility, and classes of vegetative cover.

Morrison, R. B.↗