Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Microwave-assisted hydrothermally grown epitaxial ZnO films on Left-Pointing-Angle-Bracket 1 1 1 Right-Pointing-Angle-Bracket MgAl{sub 2}O{sub 4} substrate

In this report, epitaxial ZnO films were grown on Left-Pointing-Angle-Bracket 1 1 1 Right-Pointing-Angle-Bracket MgAl{sub 2}O{sub 4} single crystal substrates using Microwave Assisted Hydrothermal (MAH) method with microwave radiation heating (2.45 GHz) at 90 Degree-Sign C in a short time (within 15 min). Scanning electron microscopy confirms that these films possess smooth surface morphology with fully coalesced grains. In addition, photoluminescence (PL) measurements exhibit strong ultraviolet emission at room temperature, indicating potential applications for short-wave light-emitting photonic devices. The PL properties were improved by a thermal annealing process without generating structural defects. Hall measurements after thermal treatment show the carrier concentration to be of the order of 10{sup 19} cm{sup -3} which is comparable to those grown by conventional solution methods. The MAH method will offer a rapid route to synthesize epitaxial ZnO films with good optical and electrical properties for various applications. - Graphical abstract: FESEM images showing the morphology and cross sectional view of ZnO films grown using microwave assisted hydrothermal method at 90 Degree-Sign C for 30 min. Highlights: Black-Right-Pointing-Pointer Microwave Assisted Hydrothermal (MAH) method was introduced to synthesize epitaxial ZnO films. Black-Right-Pointing-Pointer The films possess smooth surface morphology, fully coalesced grains with high optical properties. Black-Right-Pointing-Pointer It exhibit good electrical properties (carrier concentration 10{sup 19} cm{sup -3}, mobility 19 cm{sup 2}/Vs).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗

Microwave plasma enhanced chemical vapor deposition of nanocrystalline diamond films by bias-enhanced nucleation and bias-enhanced growth

Effects of biasing voltage-current relationship on microwave plasma enhanced chemical vapor deposition of ultrananocrystalline diamond (UNCD) films on (100) silicon in hydrogen diluted methane by bias-enhanced nucleation and bias-enhanced growth processes are reported. Three biasing methods are applied to study their effects on nucleation, growth, and microstructures of deposited UNCD films. Method A employs 320 mA constant biasing current and a negative biasing voltage decreasing from −490 V to −375 V for silicon substrates pre-heated to 800 °C. Method B employs 400 mA constant biasing current and a decreasing negative biasing voltage from −375 V to −390 V for silicon pre-heated to 900 °C. Method C employs −350 V constant biasing voltage and an increasing biasing current up to 400 mA for silicon pre-heated to 800 °C. UNCD nanopillars, merged clusters, and dense films with smooth surface morphology are deposited by the biasing methods A, B, and C, respectively. Effects of ion energy and flux controlled by the biasing voltage and current, respectively, on nucleation, growth, microstructures, surface morphologies, and UNCD contents are confirmed by scanning electron microscopy, high-resolution transmission-electron-microscopy, and UV Raman scattering.

36 MATERIALS SCIENCE↗

Effect of nitrogen on the growth of boron doped single crystal diamond

Boron-doped single crystal diamond films were grown homoepitaxially on synthetic (100) Type Ib diamond substrates using microwave plasma assisted chemical vapor deposition. A modification in surface morphology of the film with increasing boron concentration in the plasma has been observed using atomic force microscopy. Use of nitrogen during boron doping has been found to improve the surface morphology and the growth rate of films but it lowers the electrical conductivity of the film. The Raman spectra indicated a zone center optical phonon mode along with a few additional bands at the lower wavenumber regions. The change in the peak profile of the zone center optical phonon mode and its downshift were observed with the increasing boron content in the film. Furthermore, sharpening and upshift of Raman line was observed in the film that was grown in presence of nitrogen along with diborane in process gas.

36 MATERIALS SCIENCE↗

Highly Reversible Plating/Stripping of Porous Zinc Anodes for Multivalent Zinc Batteries

Zinc continues to garner immense interest due to its versatility as an anode material in several configurations utilizing either alkaline or mild-pH electrolytes. Current research on using mild-pH electrolytes has improved the rechargeability aspect of Zn-based batteries since Zn2+ is solely utilized for plating/stripping of Zn. Several studies have incorporated Zn metal foils, yet, dramatic improvements can be achieved by expressing Zn as a porous structure. Herein, we use a quasi-pulsed electrodeposition process to prepare a conformal Zn coating onto 3D porous copper foam. By tuning the electrodeposition parameters, we achieved an optimal Zn coating that undergoes reversible plating/stripping when tested in symmetric Zn cells, which supported a low overpotential of ~60 mV for up to 100 cycles. We further investigated changes in the surface morphology by studying the Zn surface of both foil and 3D structure using scanning electron microscopy and X-ray micro-computed tomography. Both techniques showed that the Zn foil undergoes dramatic alterations at the surface, which results in inhomogeneous deposition of Zn, whereas the 3D form exhibited minimal changes. Lastly, we paired both Zn foil and 3D Zn with vanadium oxide and demonstrated that the porous structure supports high rate capability and high specific capacity.

25 ENERGY STORAGE↗

Effect of annealing temperature on the photocatalytic activity of sol-gel derived TiO{sub 2} thin films

Transparent TiO{sub 2} thin films were deposited on glass substrates by a sol-gel dip coating technique, where crystallinity can be achieved at a relatively low annealing temperature. In this sol-gel preparation technique, acetic acid was used as a catalyst. Repetitive dip coating and drying, with a single annealing has made this technique easier to prepare TiO{sub 2} thin film with desired thickness within a short period of time. The crystallographic and optical properties of TiO{sub 2} films were investigated in detail. The photocatalytic activity was evaluated by the measurement of decomposition of methanol under UV-visible irradiation. The rate of decomposition of gaseous methyl alcohol depends on the structures and surface properties of the TiO{sub 2} films. The structure of the TiO{sub 2} films, prepared at various annealing temperatures, shows different crystallinities. Although crystallinity has been observed for 300 deg. C annealing temperature, it improved with increasing annealing temperature. The average transmittances of the TiO{sub 2} films slightly decrease with the increase of the annealing temperature in the range of 900-380 nm. The optical transmission edge of the TiO{sub 2} films, annealed at different annealing temperatures shifts toward higher wavelength with higher annealing temperature. All the as-deposited TiO{sub 2} films successfully photocatalyzed methanol to CO{sub 2} and H{sub 2}O, measured by Fourier transform infrared spectrometer. The decomposition efficiency of TiO{sub 2} films increased with decrease of annealing temperature. The surface morphology of all the samples was investigated by field emission scanning electron microscopy and atomic force microscopy measurements. The higher photocatalytic activity of the sample prepared at lower annealing temperature was explained by the effect of more porous structure with smaller grains and open surface morphology of the sample.

36 MATERIALS SCIENCE↗

Generation of Subsurface Voids, Incubation Effect, and Formation of Nanoparticles in Short Pulse Laser Interactions with Bulk Metal Targets in Liquid: Molecular Dynamics Study

The ability of short pulse laser ablation in liquids to produce clean colloidal nanoparticles and unusual surface morphology has been employed in a broad range of practical applications. In this paper, we report the results of large-scale molecular dynamics simulations aimed at revealing the key processes that control the surface morphology and nanoparticle size distributions by pulsed laser ablation in liquids. The simulations of bulk Ag targets irradiated in water are performed with an advanced computational model combining a coarse-grained representation of liquid environment and an atomistic description of laser interaction with metal targets. For the irradiation conditions that correspond to the spallation regime in vacuum, the simulations predict that the water environment can prevent the complete separation of the spalled layer from the target, leading to the formation of large subsurface voids stabilized by rapid cooling and solidification. The subsequent irradiation of the laser-modified surface is found to result in a more efficient ablation and nanoparticle generation, thus suggesting the possibility of the incubation effect in multipulse laser ablation in liquids. The simulations performed at higher laser fluences that correspond to the phase explosion regime in vacuum reveal the accumulation of the ablation plume at the interface with the water environment and the formation of a hot metal layer. The water in contact with the metal layer is brought to the supercritical state and provides an environment suitable for nucleation and growth of small metal nanoparticles from metal atoms emitted from the hot metal layer. The metal layer itself has limited stability and can readily disintegrate into large (tens of nanometers) nanoparticles. The layer disintegration is facilitated by the Rayleigh–Taylor instability of the interface between the higher density metal layer decelerated by the pressure from the lighter supercritical water. The nanoparticles emerging from the layer disintegration are rapidly cooled and solidified due to the interaction with water environment, with a cooling rate of ~2 × 10 12 K/s observed in the simulations. The computational prediction of two distinct mechanisms of nanoparticle formation yielding nanoparticles with different characteristic sizes provides a plausible explanation for the experimental observations of bimodal nanoparticle size distributions in laser ablation in liquids. The ultrahigh cooling and solidification rates suggest the possibility for generation of nanoparticles featuring metastable phases and highly nonequilibrium structures.

Chemistry↗

Differences in the Interfacial Mechanical Properties of Thiophosphate and Argyrodite Solid Electrolytes and Their Composites

Interfacial mechanics are a significant contributor to the performance and degradation of solid-state batteries. Spatially resolved measurements of interfacial properties are extremely important to effectively model and understand the electrochemical behavior. Herein, we report the interfacial properties of thiophosphate (Li 3 PS 4 )- and argyrodite (Li 6 PS 5 Cl)-type solid electrolytes. Using atomic force microscopy, we showcase the differences in the surface morphology as well as adhesion of these materials. Additionally we investigate solvent-less processing of hybrid electrolytes using UV-assisted curing. Physical, chemical, and structural characterizations of the materials highlight the differences in the surface morphology, chemical makeup, and distribution of the inorganic phases between the argyrodite and thiophosphate solid electrolytes.

36 MATERIALS SCIENCE↗

Metalorganic chemical vapor deposition-regrown Ga-rich InGaP films on SiGe virtual substrates for Si-based III-V optoelectronic device applications

Ga-rich InGaP materials are attractive applications for yellow-green spectral range optoelectronics such as light-emitting diodes and solar cells on silicon substrate. Bulk, Ga-rich InGaP films grown by metalorganic chemical vapor deposition on SiGe virtual substrates were investigated in the V/III compositional ratio range of 44.3–402 using chamber pressures from 100 to 200 mbar. These films were nominally lattice matched to the SiGe virtual substrate with a bandgap energy of 2.07–2.09 eV at low temperature (10 K). The authors show that the surface morphology of the Ga-rich InGaP films was dependent on the growth conditions, including the V/III gas phase ratio, pressure, and growth rate. By optimizing the growth conditions, the authors achieved improved surface morphologies of the Ga-rich InGaP films. The hillock density of the films produced using a V/III gas phase ratio of 44.3 and 75.4, a growth pressure of 100 mbar, and a growth rate of 0.9 μm/h was about an order of magnitude lower (30.3–50 × 104 cm−2) than that observed using higher V/III gas phase ratios such as 201 and 402. An increase in luminescence efficiency of Ga-rich InGaP materials was observed when the hillock density is lower. The authors discuss the mechanisms of the hillock formation.

Kim, TaeWan↗

High-temperature phase transformation and topochemical nature in ferroelastic (NH{sub 4}){sub 2}SO{sub 4}

The electrical conductivity of ferroelastic ammonium sulfate (NH{sub 4}){sub 2}SO{sub 4} revealed an anomaly at around 130 °C (=403 K, T{sub P}) on heating with large and irreversible thermal hysteresis through thermal cycle. Ferroelastic domain walls and surface morphology of (NH{sub 4}){sub 2}SO{sub 4} were investigated by hot-stage polarizing microscopy. Structural phase transition from an orthorhombic ferroelastic phase to a hexagonal paraelastic phase was not identified at T{sub P} upon heating. On further heating above T{sub P}, microscopic spots appeared and grew on the crystal surface, suggesting that the high-temperature anomaly at T{sub P} was an indication of an onset of thermal decomposition controlled by topochemical factors. The increase of electrical conductivity above T{sub P} was attributed to proton migration. - Graphical abstract: Surface morphology of the (100) face of (NH{sub 4}){sub 2}SO{sub 4} on heating, showing chemical reaction at the surface. - Highlights: • We investigate the high-temperature phase transformation of ammonium sulfate. • The increasing conductivity upon heating is attributed to proton migration. • Structural phase transition from orthorhombic to hexagonal phase is not confirmed. • High-temperature anomaly is related to an onset of thermal decomposition. • The nature of the high-temperature anomaly is topochemical controlled by defects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Controlling the crystallite size and influence of the film thickness on the optical and electrical characteristics of nanocrystalline Cu{sub 2}S films

Highlights: Black-Right-Pointing-Pointer Modification of the preparation technique in order to deposit nanostructure Cu{sub 2}S thin films. Black-Right-Pointing-Pointer Controlling the crystallite size of the prepared films. Black-Right-Pointing-Pointer Study the surface morphology, optical and electrical characteristics of Cu{sub 2}S films. -- Abstract: In this work, Cu{sub 2}S nanocrystalline films have been successfully prepared using dip-coating technique. The stoichiometry and the structural characteristics of the prepared films were characterized by energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD), respectively. The surface morphology of the deposited Cu{sub 2}S film was studied using both the scanning electron microscopy (SEM) and the atomic force microscopy (AFM). The SEM and AFM images indicate that the prepared Cu{sub 2}S films are characterized by a well-dispersed and highly dense with spherical like-shaped aggregates of size in the nano scale. The optical absorption measurements indicate that the Cu{sub 2}S nanoparticles have a direct band gap of 2.92 eV. The dispersion and absorption parameters such as the dispersion energy, oscillating energy, real and imaginary dielectric constants and dissipation factor were calculated within a wide wavelength range of the spectrum that indicates the suitability of the deposited films as solar absorber using this technique. The dark electrical resistivity ({rho}) measurements were carried out at different temperatures in the range 312-440 K. These results confirm the semiconducting characteristic of the prepared Cu{sub 2}S films. Moreover, two activation energies were obtained that indicate the presence of two dominating conduction mechanisms in these temperature ranges. The bulk electrical resistivity ({rho}{sub B}) and the mean free path (l{sub 0}) of charge carriers were estimated from the resistivity-thickness dependence. The heterojunction device of n-ZnCdS/p-Cu{sub 2}S behaves good rectifying property. The photovoltaic characteristic of the heterojunction device using the current-voltage characteristic under illumination of 100 mW/cm{sup 2} was also observed. Discussion of the obtained results and their comparison with the previous published data were also considered.

36 MATERIALS SCIENCE↗

Fs-laser processing of polydimethylsiloxane

We present an experimental analysis on surface structuring of polydimethylsiloxane films with UV (263 nm) femtosecond laser pulses, in air. Laser processed areas are analyzed by optical microscopy, SEM, and μ-Raman spectroscopy. The laser-treated sample shows the formation of a randomly nanostructured surface morphology. μ-Raman spectra, carried out at both 514 and 785 nm excitation wavelengths, prior and after laser treatment allow evidencing the changes in the sample structure. The influence of the laser fluence on the surface morphology is studied. Finally, successful electro-less metallization of the laser-processed sample is achieved, even after several months from the laser-treatment contrary to previous observation with nanosecond pulses. Our findings address the effectiveness of fs-laser treatment and chemical metallization of polydimethylsiloxane films with perspective technological interest in micro-fabrication devices for MEMS and nano-electromechanical systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of different mechanisms of GaN growth induced on AlN and GaN nucleation layers

The evolution of GaN growth on AlN and GaN nucleation layers is compared through morphological and structural analyses, including ion beam analysis. By using AlN nucleation layer grown at high temperature, improved crystalline quality is exhibited by 300 nm thin GaN epilayers. GaN (002) x-ray rocking curve as narrow as 168 arc sec and atomic-step surface morphology characterize such a thin GaN film on AlN. Defects are strongly confined into the first 50 nm of growth, whereas a fast laterally coherent growth is observed when increasing thickness, as an effect of high temperature AlN surface morphology and Ga adatom dynamics over this template.

36 MATERIALS SCIENCE↗

Effect of film thickness on structural and mechanical properties of AlCrN nanocompoite thin films deposited by reactive DC magnetron sputtering

In this study, the influence of film thickness on the structural, surface morphology and mechanical properties of Aluminum chromium nitride (AlCrN) thin films has been successfully investigated. The AlCrN thin films were deposited on silicon (100) substrate using dc magnetron reactive co-sputtering at substrate temperature 400° C. The structural, surface morphology and mechanical properties were studied using X-ray diffraction, field-emission scanning electron microscopy and nanoindentation techniques respectively. The thickness of these thin films was controlled by varying the deposition time therefore increase in deposition time led to increase in film thickness. X-ray diffraction pattern of AlCrN thin films with different deposition time shows the presence of (100) and (200) orientations. The crystallite size varies in the range from 12.5 nm to 36.3 nm with the film thickness due to surface energy minimization with the higher film thickness. The hardness pattern of these AlCrN thin films follows Hall-Petch relation. The highest hardness 23.08 Gpa and young modulus 215.31 Gpa were achieved at lowest grain size of 12.5 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

An atomistic mechanism study of GaN step-flow growth in vicinal m -plane orientations

We present elucidation of homoepitaxial growth mechanisms on vicinal non-polar surfaces of GaN that is highly important for gaining an understanding of and control thin film surface morphology and properties. Using first-principles calculations, we study the step-flow growth in m-plane GaN based on atomic row nucleation and kink propagation kinetics. Ga–N dimer adsorption onto the m-plane is energetically more favorable than that of Ga and N isolated adatoms. Therefore, we have treated the dimers as the dominant growth species attached to the step edges. By calculating the free energies of sequentially attached Ga–N dimers, we have elucidated that the a-step edge kink growth proceeds by parallel attachment rather than by across the step edge approach. We found a series of favorable configurations of kink propagation and calculated the free energy and nucleation barriers for kink evolution on five types of step edges (a, +c, -c, +a + c, and -a - c). By changing the chemical potential μGa and the excess chemical potential Δμ, the growth velocities at the five types of edges are controlled by the corresponding kink pair nucleation barrier E* in their free energy profiles. To explore the kink-flow growth instability observed at different Ga/N flux ratios, calculations of kink pairs on the incompact -c and +c-step edges are further performed to study their formation energies. Variations of these step edge morphologies with a tuned chemical environment are consistent with previous experimental observations, including stable diagonal ±a ± c-direction steps. In conclusion, our work provides a first-principles approach to explore step growth and surface morphology of the vicinal m-plane GaN, which is applicable to analyze and control the step-flow growth of other binary thin films.

36 MATERIALS SCIENCE↗

17.1%-Efficient Multi-Scale-Textured Black Silicon Solar Cells without Dielectric Antireflection Coating: Preprint

In this work we present 17.1%-efficient p-type single crystal Si solar cells with a multi-scale-textured surface and no dielectric antireflection coating. Multi-scale texturing is achieved by a gold-nanoparticle-assisted nanoporous etch after conventional micron scale KOH-based pyramid texturing (pyramid black etching). By incorporating geometric enhancement of antireflection, this multi-scaletexturing reduces the nanoporosity depth required to make silicon 'black' compared to nanoporous planar surfaces. As a result, it improves short-wavelength spectral response (blue response), previously one of the major limiting factors in 'black-Si' solar cells. With multi-scale texturing, the spectrum-weighted average reflectance from 350- to 1000-nm wavelength is below 2% with a 100-nm deepnanoporous layer. In comparison, roughly 250-nm deep nanopores are needed to achieve similar reflectance on planar surface. Here, we characterize surface morphology, reflectivity and solar cell performance of the multi-scale textured solar cells.

14 SOLAR ENERGY↗

Growth evolution of AlN films on silicon (111) substrates by pulsed laser deposition

AlN films with various thicknesses have been grown on Si(111) substrates by pulsed laser deposition (PLD). The surface morphology and structural property of the as-grown AlN films have been investigated carefully to comprehensively explore the epitaxial behavior. The ∼2 nm-thick AlN film initially grown on Si substrate exhibits an atomically flat surface with a root-mean-square surface roughness of 0.23 nm. As the thickness increases, AlN grains gradually grow larger, causing a relatively rough surface. The surface morphology of ∼120 nm-thick AlN film indicates that AlN islands coalesce together and eventually form AlN layers. The decreasing growth rate from 240 to 180 nm/h is a direct evidence that the growth mode of AlN films grown on Si substrates by PLD changes from the islands growth to the layer growth. The evolution of AlN films throughout the growth is studied deeply, and its corresponding growth mechanism is hence proposed. These results are instructional for the growth of high-quality nitride films on Si substrates by PLD, and of great interest for the fabrication of AlN-based devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A Novel Wet-Chemical Route for Synthesis of Multiferroic AMnO{sub 3} (A = Gd, Tb, Dy) Particles and Its Structural, Optical and Magnetic Properties

Several multiferroic AMnO{sub 3} (A = Gd, Tb, Dy) particles were synthesized by microwave-assisted acrylamide gel route. The influence of A-site cation on the phase purity, surface morphologies, and optical and magnetic properties of the as-prepared multiferroic AMnO{sub 3} (A = Gd, Tb, Dy) particles was investigated. X-ray diffraction pattern, Fourier transform infrared spectroscopy, and Raman spectroscopy confirm the pure phase of the AMnO{sub 3} (A = Gd, Tb, Dy) particles exhibits an orthorhombic perovskite structure. Scanning electron microscopy (SEM) observation indicates that the surface morphology of AMnO{sub 3} (A = Gd, Tb, Dy) particles is significantly dependent on the A-site cation. The particle size of AMnO{sub 3} (A = Gd, Tb, Dy) particles increases with the increasing atomic number of A-site cation The optical band gap values of AMnO{sub 3} (A = Gd, Tb, Dy) particles decrease with an increase in the atomic number of A-site cation. Magnetization measurements show that these AMnO{sub 3} (A = Gd, Tb, Dy) particles exhibit magnetic ordering at low temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗