Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Basic Research of Intrinsic Tamper indication Markings and Patterns defined by Pulsed Laser Irradiation

With our previous research, it was found that surface asperities or roughness must be present to create periodic surface structures upon laser exposure. In particular, an initial rough surface morphology (such as that found with a machined surface) provides multiple sites for light scattering, which underlies the formation of periodic ripple morphologies. Light scattering from a random surface creates patterns of periodic structures (with complex orientations) that could be used as intrinsic markings for tagging materials and equipment. Despite these initial findings, the fundamental mechanisms that give rise to periodic surface structures and their characteristic shapes were not identified in prior research.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Reliable solution processed planar perovskite hybrid solar cells with large-area uniformity by chloroform soaking and spin rinsing induced surface precipitation

A solvent soaking and rinsing method, in which the solvent was allowed to soak all over the surface followed by a spinning for solvent draining, was found to produce perovskite layers with high uniformity on a centimeter scale and with much improved reliability. Besides the enhanced crystallinity and surface morphology due to the rinsing induced surface precipitation that constrains the grain growth underneath in the precursor films, large-area uniformity with film thickness determined exclusively by the rotational speed of rinsing spinning for solvent draining was observed. With chloroform as rinsing solvent, highly uniform and mirror-like perovskite layers of area as large as 8 cm × 8 cm were produced and highly uniform planar perovskite solar cells with power conversion efficiency of 10.6 ± 0.2% as well as much prolonged lifetime were obtained. The high uniformity and reliability observed with this solvent soaking and rinsing method were ascribed to the low viscosity of chloroform as well as its feasibility of mixing with the solvent used in the precursor solution. Moreover, since the surface precipitation forms before the solvent draining, this solvent soaking and rinsing method may be adapted to spinless process and be compatible with large-area and continuous production. With the large-area uniformity and reliability for the resultant perovskite layers, this chloroform soaking and rinsing approach may thus be promising for the mass production and commercialization of large-area perovskite solar cells.

14 SOLAR ENERGY↗
DOE OSTI2024

Surface Self-Diffusion Induced Sintering of Nanoparticles

Despite the critical role of sintering phenomena in constraining the long-term durability of nanosized particles, a clear understanding of nanoparticle sintering has remained elusive due to the challenges in atomically tracking the neck initiation and discerning different mechanisms. Through the integration of in situ transmission electron microscopy and atomistic modeling, this study uncovers the atomic dynamics governing the neck initiation of Pt–Fe nanoparticles via a surface self-diffusion process, allowing for coalescence without significant particle movement. Real-time imaging reveals that thermally activated surface morphology changes in individual nanoparticles induce significant surface self-diffusion. Further, the kinetic entrapment of self-diffusing atoms in the gaps between closely spaced nanoparticles leads to the nucleation and growth of atomic layers for neck formation. This surface self-diffusion-driven sintering process is activated at a relatively lower temperature compared to the classic Ostwald ripening and particle migration and coalescence processes. The fundamental insights have practical implications for manipulating the morphology, size distribution, and stability of nanostructures by leveraging surface self-diffusion processes.

36 MATERIALS SCIENCE↗
NASA NTRS1984

A morphological study of silicon carbide prepared by chemical vapor deposition

Surface morphologies of SiC deposits obtained via chemical vapor deposition (CVD) were studied as functions of substrate surface temperature and the concentration of the silicon and carbon source material, methyltrichlorosilane. Substrates of graphite and alpha-SiC crystals were used. Explanations of the observed morphologies on graphite substrates and their marked changes with temperature are given in terms of chemical kinetics and mass transport arguments. The results of thermodynamic calculations were used to help explain the observed morphologies of the deposits on alpha-SiC substrates.

Tsui, P.↗
DOE OSTI2020

Surface modification of bamboo fiber with sodium hydroxide and graphene oxide in epoxy composites

Bamboo fibers (BFs) have high mechanical properties and are candidate reinforcement for epoxy matrix composites. However, to improve performance, good fiber-matrix interaction is required. In this work, unidirectional long BF reinforced epoxy composites at fiber volume content of 22%, 40%, and 50% were made by compression molding. The 40 v% untreated BF reinforced composites exhibited 107% and 439% increase for flexural strength and modulus, respectively, compared to neat epoxy. Sodium hydroxide (NaOH) treatment was used to modify the surface of the BFs, and then the NaOH modified BFs were coated with graphene oxide (GO). The 40 v% NaOH modified BF composites showed an improvement from 259.9 to 327.5 MPa for flexural strength and from 16.7 to 21.5 GPa for flexural modulus, compared to 40 v% untreated BF composites. Slight improvement in properties up to 334.6 MPa for flexural strength and up to 23.8 GPa for flexural modulus was achieved for composites made of 40 v% NaOH/GO modified BF. Surface modification of BF after the NaOH and NaOH/GO treatment was confirmed by X-ray photoelectron spectroscopy and by scanning electron microscopy, which showed differences on the fiber surface morphology and on the composite fracture surface. This BF surface modification approach with GO has potential to impart other properties beyond mechanical to produce multifunctional composite and lead to the use of sustainable plant fibers as alternatives to synthetic fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Electrochemical Characterization of Certain Mg-Based Alloys in Artificial Perspiration Biofluid for Consumer and Industrial Applications

The weight reduction of numerous consumer electronic devices is of increasing importance. In this respect, ultra-light magnesium alloys have attracted more attention to be used as frame materials. Nevertheless, Mg alloys are of intrinsically poor corrosion resistance, especially in chloride ion-containing environments. Human perspiration fluid with a relatively high chloride ions content (~ 0.14 M) comes in contact with a number of consumer products resulting in a variety of undesirable effects such as malfunction and corrosion. Based on that, the present work addresses the corrosion behavior of five AZ-Mg alloys including AZ91D, AZ80E, AZ31, AM60 and AXJ530 in artificial perspiration biofluid at human body temperature of 37 °C. The study is performed using electrochemical impedance spectroscopy and potentiodynamic polarization techniques supported by surface morphological and EDX spectra examinations. The surface layer total resistance value (R{sub T}) estimated from the analysis of obtained impedance data after 12-h exposure period reveals that durability of our tested samples increases in the following sequence: AZ80 > AZ91 > AZ31 > AM60 > AXJ530 > Mg (control). AZ80E alloy at top of this sequence points to its significantly high anti-corrosion performance in artificial perspiration biofluid and thus can be the best Mg materials of choice for many housing consumer electronic products. This outcome is in consistence with the corrosion rate (P{sub i} in mm y{sup −1}) trend as derived from the potentiodynamic polarization data that decreases in the following order: AZ80 (0.25) < AZ91 (0.49) < AZ31 (1.03) < AM60 (1.23) < AXJ530 (5.36) < Mg (5.98). Both FE-SEM images and EDX analyses further confirm these experimentally electrochemical findings.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Using soft x-ray absorption spectroscopy to characterize electrode/electrolyte interfaces in-situ and operando

The interfaces between electrode and electrolyte play a vital role in various electrochemical systems. However, the understanding of such embedded interfaces and interfacial processes is still limited partly because of the short of proper characterizations tools, especially in-situ/operando techniques. Previously, substantial effort has been devoted in the development of in-situ/operando techniques to investigate the solid/liquid interfaces. One successful approach is the combination of in-situ liquid cells and soft x-ray absorption spectroscopy (sXAS). Here, we showcased several recent examples using such liquid-cell-based in-situ/operando sXAS method to study different aspects of the electrode/electrolyte interface under reaction conditions, including the adsorption and deposition of solute species on electrode surface, morphological and chemical changes of electrode surface, and potential-dependent orientations of interfacial solvent molecules. These examples demonstrated capability of such in-situ/operando sXAS techniques in providing element- and chemical-sensitive interfacial information. This in-situ/operando sXAS technique also opens the way to the investigation of various solid/liquid interfaces in other important heterogeneous reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Observation of tantalum deposition and growth on TiB2 and ZrB2 from PISCES-RF deuterium and helium plasma exposures

Deuterium and helium plasma exposures on bulk TiB2 and ZrB2 samples were performed using the PISCES-RF linear plasma device. 40 and 90 eV deuterium ion plasma exposures were performed at 240 and 800 °C sample temperatures, and 80 eV helium ion plasma exposures were performed at 800 °C sample temperatures. Following plasma exposures, it was discovered that two plasma conditions (90 eV deuterium and 80 eV helium at 800 °C) resulted in thick (>200 nm) tantalum-rich (>10 at%) surface features on the targets, presumably from tantalum sourced from a tantalum adapter mask or cap used as part of the target holder. This work aims to characterize these tantalum-rich features and examine the mechanisms of impurity deposition.Plasma-induced surface morphology of the tantalum-rich surface layers depends on plasma properties and target temperature and chemistry. Greater titanium sputtering compared to zirconium resulted in more distinct surface features in the TiB2 samples compared to the ZrB2 samples via increased, prompt deposition onto tantalum surface impurities. There is still uncertainty as to why thick tantalum deposition only occurred under some plasma exposure conditions but not others; it is likely due to tantalum sputtering by a combination of boron molecules from the targets and carbon-impurities in the tantalum mask or targets. Impurity driven surface features are a well-documented phenomena in samples exposed to plasma from linear plasma device facilities—this work confirms the occurrence of this and emphasizes the need for chemistry characterization of isolated post-mortem surface features in plasma-exposed samples.

Nuckols, Lauren↗
DOE OSTI2020

Pool boiling critical heat flux studies of accident tolerant fuel cladding materials

Pool boiling experiments have been performed at atmospheric pressure on potential accident tolerant fuel (ATF) cladding materials (Zirlo®, Cr coated Zirlo®, FeCrAl coated Zirlo®, and monolithic SiC) to evaluate the Critical Heat Flux (CHF) points. Corrosion resistant coatings of Cr and FeCrAl alloy were deposited on flat Zirlo® samples using cold spray technology. The as-prepared samples after uniform surface polishing were subjected to autoclave tests at 360 °C water and 18.6 MPa for 360 h to simulate prototypic corrosion of the ATF cladding materials in LWR normal operation. Surface characteristics potentially influencing CHF such as surface morphology, roughness, static contact angle, and surface chemistry were characterized using a suite of characterization methods including scanning electron microscopy, 3D optical profilometry, optical contact angle measurements, and x-ray photoelectron spectroscopy (XPS). Thermo-physical properties of the samples such as density, thermal conductivity, and heat capacity were measured by differential scanning calorimetry and laser flash thermal diffusivity measurement. FeCrAl coatings showed CHF values comparable to bare Zirlo® samples, while slightly lower CHF values were observed for Cr coated samples and bulk SiC flats (produced by chemical vapor deposition, CVD). As-deposited Cr coatings showed 67% higher CHF than the as-polished Cr coatings due to its higher surface roughness level. The autoclave testing for the prepared samples generally increased the CHF except for the surface polished Cr coatings. Similar CHF values of bare Zirlo®, FeCrAl coating, and CVD SiC samples were observed after autoclave test but there were negligible change CHF of Cr coatings. XPS studies indicated that the formation or deposition of a few monolayers of hydrophobic carbonaceous species on surface can affect CHF values. The trends in CHF data are discussed in terms of evolution of the surface characteristics of the ATF materials.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Stability Enhancement and Microstructural Modification of Ni-Rich Cathodes via Halide Doping

In this study, elemental doping is an effective strategy to modify surface and bulk chemistry in NMC cathode materials. By adding small amounts of lithium halide salts during the calcination process, the Ni-rich NMC811 cathode is doped with Br, Cl, or F halogens. The dopant type has a significant impact on the lithiation process and heavily influences the final cathode porosity and surface morphology. Utilizing a variety of electrochemical, surface, and bulk characterization techniques, it is demonstrated that an initial content of 5 mol % LiBr or LiCl in the lithium source is effective in improving capacity retention while also providing excellent rate performance. The improvements are attributed to a substantial increase in specific surface area, the formation of a stable cathode electrolyte interface (CEI) layer, and suppressed surface reconstruction. In addition, the particle microstructure is better equipped to handle cyclic volume changes with increased values of critical crack lengths. Overall, it is demonstrated that anion doping via the addition of lithium halide salts is a facile approach toward Ni-rich NMC modification for enhanced cathode performance.

25 ENERGY STORAGE↗
DOE OSTI2015

Effect of substrate rotation on domain structure and magnetic relaxation in magnetic antidot lattice arrays

Microdimensional triangular magnetic antidot lattice arrays were prepared by varying the speed of substrate rotation. The pre-deposition patterning has been performed using photolithography technique followed by a post-deposition lift-off. Surface morphology taken by atomic force microscopy depicted that the growth mechanism of the grains changes from chain like formation to island structures due to the substrate rotation. Study of magnetization reversal via magneto optic Kerr effect based microscopy revealed reduction of uniaxial anisotropy and increase in domain size with substrate rotation. The relaxation measured under constant magnetic field becomes faster with rotation of the substrate during deposition. The nature of relaxation for the non-rotating sample can be described by a double exponential decay. However, the relaxation for the sample with substrate rotation is well described either by a double exponential or a Fatuzzo-Labrune like single exponential decay, which increases in applied field.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Hydrogen Sulfide Passivation for p-Type Passivated Emitter and Rear Contact Solar Cells

This work reports on the application of sulfur (S)-passivation to passivated emitter and rear contact (PERC) solar cells. The emitter surface was passivated by hydrogen sulfide (H 2 S) gas phase reaction and capped by a hydrogenated amorphous silicon nitride (a-SiN x :H) layer. The sulfur passivation on a symmetrically n + diffused emitter is shown to lead to an emitter saturation current density (J 0n+ ) of 30 fA/cm 2 at R sheet,n+ ≈ 100 Ω/sq. The application of S-passivation to the emitter surface in the PERC cell structure, with the rear surface passivated by an aluminum oxide (Al 2 O 3 )/a-SiN x :H stack, showed a promising implied open-circuit voltage (iV OC ) of 686 mV before metallization. This iV OC was higher than that for the a-SiN x :H or SiO 2 /a-SiN x :H passivated emitter surfaces (675 and 674 mV, respectively) on PERC cells processed in the same run. However, a significant drop in cell V OC is observed for the S-passivated PERC cell after the completion of device fabrication with laser patterning, screen-printed metal contact deposition, and firing. Nonetheless, an efficiency of ~20% and a V OC of ~650 mV was achieved with an emitter surface passivated by sulfur. We identified that the 760°C contact firing process degrades the S-passivation quality. Furthermore, the surface morphology was studied, and a detailed surface analysis was performed to study the causes of the S-passivated surface degradation.

14 SOLAR ENERGY↗
DOE OSTI2019

Investigation of the Current–Voltage Characteristics of New MnO{sub 2}/GaAs(100) and V{sub 2}O{sub 5}/GaAs(100) Heterostructures Subjected to Heat Treatment

Complex oxide films with a thickness of about 200 nm are formed during the thermal oxidation of GaAs with magnetron-deposited V{sub 2}O{sub 5} and MnO{sub 2} nanolayers. The electrical parameters of the films (reverse-bias breakdown voltage and current density) are determined by the method of current–voltage (I–V) characteristics at room temperature in the bias range from –5 to +5 V, and their composition and surface morphology are investigated. It is shown that V{sub 2}O{sub 5} facilitates the more intense (in comparison with MnO{sub 2}) chemical bonding of arsenic at the internal interface with the formation of As{sub 2}O{sub 5}. As a result, thermally oxidized V{sub 2}O{sub 5}/GaAs heterostructures exhibit higher breakdown voltages.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1981

Encounter with Saturn - Voyager 1 imaging science results

As Voyager 1 flew through the Saturn system it returned photographs revealing many new and surprising characteristics of this complicated community of bodies. Saturn's atmosphere has numerous, low-contrast, discrete cloud features and a pattern of circulation significantly different from that of Jupiter. Titan is shrouded in a haze layer that varies in thickness and appearance. Among the icy satellites there is considerable variety in density, albedo, and surface morphology and substantial evidence for endogenic surface modification. Trends in density and crater characteristics are quite unlike those of the Galilean satellites. Small inner satellites, three of which were discovered in Voyager images, interact gravitationally with one another and with the ring particles in ways not observed elsewhere in the solar system. Saturn's broad A, B, and C rings contain hundreds of 'ringlets', and in the densest portion of the B ring there are numerous nonaxisymmetric features. The narrow F ring has three components which, in at least one instance, are kinked and crisscrossed. Two rings are observed beyond the F ring, and material is seen between the C ring and the planet.

Smith, B. A.↗
NASA NTRS2006

Solar Effects on Tensile and Optical Properties of Hubble Space Telescope Silver-Teflon(Registered Trademark) Insulation

A section of the retrieved Hubble Space Telescope (HST) solar array drive arm (SADA) multilayer insulation (MLI), which experienced 8.25 years of space exposure, was analyzed for environmental durability of the top layer of silver-Teflon (DuPont) fluorinated ethylene propylene (Ag-FEP). Because the SADA MLI had solar and anti-solar facing surfaces and was exposed to the space environment for a long duration, it provided a unique opportunity to study solar effects on the environmental degradation of Ag-FEP, a commonly used spacecraft thermal control material. Data obtained included tensile properties, solar absorptance, surface morphology and chemistry. The solar facing surface was found to be extremely embrittled and contained numerous through-thickness cracks. Tensile testing indicated that the solar facing surface lost 60% of its mechanical strength and 90% of its elasticity while the anti-solar facing surface had ductility similar to pristine FEP. The solar absorptance of both the solar facing surface (0.155 plus or minus 0.032) and the anti-solar facing surface (0.208 plus or minus 0.012) were found to be greater than pristine Ag-FEP (0.074). Solar facing and anti-solar facing surfaces were microscopically textured, and locations of isolated contamination were present on the anti-solar surface resulting in increased localized texturing. Yet, the overall texture was significantly more pronounced on the solar facing surface indicating a synergistic effect of combined solar exposure and increased heating with atomic oxygen erosion. The results indicate a very strong dependence of degradation, particularly embrittlement, upon solar exposure with orbital thermal cycling having a significant effect.

deGroh, Kim, K.↗
DOE OSTI2020

Effects of surface undulations on asymmetric X-ray diffraction: a rocking-curve topography study

The results are reported of an X-ray diffraction study of an Si crystal designed and fabricated for very asymmetric diffraction from the 333 reflection for X-ray energies of 8.100 and 8.200 keV. A crystal with an asymmetry angle of 46 ± 0.1° between the surface and the (111) planes was studied. The grazing angles of incidence were near 1.08 and 0.33° for these two energies, respectively. Features arising from surface undulations were not observed at 8.100 keV, but were observed at 8.200 keV. The results at 8.100 keV allow an alternative explanation based on strain near the surface to be ruled out. Topographic images were obtained as a function of rocking angle, and in the case of 8.200 keV the surface morphology is evident. Finally, the results are found to be in agreement with dynamical X-ray diffraction calculations made with the Takagi–Taupin equations specialized to a surface having convex or concave features, as reported in the accompanying paper [Macrander (2020). J. Appl. Cryst. 53 , 793–799].

36 MATERIALS SCIENCE↗
DOE OSTI2018

Structural and Morphological Features of TiNi-Based Powder Manufactured by the Method of Hybrid-Calcium Reduction

An investigation of the structural features and surface morphology of a PV-N55T45 TiNi-based powder manufactured by the method of hybrid-calcium reduction is performed. The TiNi intermetallic compound is found in a two-phase state – B2 and В19′, and the following secondary phases are revealed: Ti{sub 2}Ni, Ti{sub 4}Ni{sub 2}(О, N, С), TiNi{sub 3}, and Ti{sub 3}Ni{sub 4}. It is observed that TiNi-based powder has dual – compact and spongy – morphology. The compact powder particles consist of oval coarse grains of TiNi separated by a massive Ti{sub 2}Ni interlayer. In the spongy particles, in contrast to the compact ones, the TiNi-phase prevails in the form of a single conglomerate of fine grains measuring 10–20 μm. In the Ni-enriched regions of the TiNi matrix the B19′-martensite is observed in multiple structural-morphological variants. In the compact particles the martensite structure represents orthogonal twin plates having different orientations within one grain. In the spongy particles, there is a different type of the martensite structure with multiple crystals of the B19′-martensite with the pyramidal lath morphology. On the surface of certain particles there is terraced relief formed due to bulk diffusion of atoms, surface diffusion of adatoms, and their interaction with the substrate defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗