Search NASA⌕ Search

SEARCH · Search NASA

Results for “teeth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Pulsed laser ablation of dental calculus in the near ultraviolet

Pulsed lasers emitting wavelengths near 400 nm can selectively ablate dental calculus without damaging underlying and surrounding sound dental hard tissue. Our results indicate that calculus ablation at this wavelength relies on the absorption of porphyrins endogenous to oral bacteria commonly found in calculus. Sub- and supragingival calculus on extracted human teeth, irradiated with 400-nm, 60-ns laser pulses at ≤8 J/cm2, exhibits a photobleached surface layer. Blue-light microscopy indicates this layer highly scatters 400-nm photons, whereas fluorescence spectroscopy indicates that bacterial porphyrins are permanently photobleached. A modified blow-off model for ablation is proposed that is based upon these observations and also reproduces our calculus ablation rates measured from laser profilometry. Tissue scattering and a stratified layering of absorbers within the calculus medium explain the gradual decrease in ablation rate from successive pulses. Depending on the calculus thickness, ablation stalling may occur at <5 J/cm2 but has not been observed above this fluence.

47 OTHER INSTRUMENTATION↗

Selective Near-UV Ablation of Subgingival Dental Calculus: Measurement of Removal Rates

A noncontact profilometer (laser triangulation) was used to measure the removal rates of subgingival dental calculus irradiated with a frequency-doubled Ti:sapphire laser (60-ns pulse duration, 400-nm wavelength, 10-Hz repetition rate, 7-mJ pulse energy). Profilometer traces before and after irradiation were used to create a removal map with 4-μm axial and 15-μm transverse resolution. Twenty-three teeth (15 with calculus and 8 pristine) were irradiated at 90° and 45° under a cooling water spray with a super-Gaussian beam (~300-μm diameter). Subgingival calculus was selectively removed at 5.6 and 4.0 J/cm2 for 90° and 45°, respecetively, within a range of rates, between 2 to 9 μm/pulse. These ablation rates were constant during these exposures. For comparison, pristine cementum irradiated for 10 min at the same peak fluence and pulse repetition rate showed only craters, 15 to 50 μm deep, corresponding to an equivalent removal rate three orders of magnitude smaller than that obtained for calculus. Pristine enamel was not removed under the same irradiation conditions.

calculus↗

Bioinspired large-scale aligned porous materials assembled with dual temperature gradients

Natural materials, such as bone, teeth, shells, and wood, exhibit outstanding properties despite being porous and made of weak constituents. Frequently, they represent a source of inspiration to design strong, tough, and lightweight materials. Although many techniques have been introduced to create such structures, a long-range order of the porosity as well as a precise control of the final architecture remain difficult to achieve. These limitations severely hinder the scale-up fabrication of layered structures aimed for larger applications. We report on a bidirectional freezing technique to successfully assemble ceramic particles into scaffolds with large-scale aligned, lamellar, porous, nacre-like structure and long-range order at the centimeter scale. This is achieved by modifying the cold finger with a polydimethylsiloxane (PDMS) wedge to control the nucleation and growth of ice crystals under dual temperature gradients. Our approach could provide an effective way of manufacturing novel bioinspired structural materials, in particular advanced materials such as composites, where a higher level of control over the structure is required.

36 MATERIALS SCIENCE↗

TiO 2 Nanocoatings with Controllable Crystal Type and Nanoscale Topography on Zirconia Implants to Accelerate Bone Formation

In dentistry, zirconia implants have emerged as a promising alternative for replacing missing teeth due to their superior aesthetic performance and chemical stability. To improve the osseointegration of zirconia implants, modifying their surface with hierarchical micro/nanotopography and bioactive chemical composition are two effective ways. In this work, a microscale topography was prepared on a zirconia surface using hydrofluoric acid etching, and then a 50 nm TiO 2 nanocoating was deposited via atomic layer deposition (ALD). Subsequently, an annealing treatment was used to transform the TiO 2 from amorphous to anatase and simultaneously generate nanoscale topography. Various investigations into the coating surface morphology, topography, wettability, and chemical composition were carried out using scanning electron microscopy, white light interferometry, contact‐angle measurement, X‐ray diffraction, and X‐ray photoelectron spectroscopy. In addition, in vitro cytocompatibility and osteogenic potential performance of the coatings were evaluated by human bone marrow mesenchymal stem cells (hBMSCs), and in vivo osseointegration performance was assessed in a rat femoral condyle model. Moreover, the possible mechanism was also investigated. The deposition of TiO 2 film with/without annealing treatment did not alter the microscale roughness of the zirconia surface, whereas the nanotopography changed significantly after annealing. The in vitro studies revealed that the anatase TiO 2 coating with regular wavelike nanostructure could promote the adhesion and proliferation of osteoblasts and further improve the osteogenic potential in vitro and osseointegration in vivo. These positive effects may be caused by nanoscale topography via the canonical Wnt/ β ‐catenin pathway. The results suggest that using ALD in combination with annealing treatment to fabricate a nanotopographic TiO 2 coating is a promising way to improve the osteogenic properties of zirconia implants.

Li, Nan (ORCID:0000000255156737)↗

A new shallow-water mud crab of the genus Hexapanopeus Rathbun, 1898 from Belize (Crustacea: Decapoda: Panopeidae)

A new species of panopeid crab from shallow coastal waters of Belize is formally described and named based upon comparative study of three small specimens obtained in the course of a regional biodiversity survey of decapod crustaceans. The herein designated holotype of Hexapanopeus klausruetzleri n. sp. is a specimen previously included in a comparative molecular phylogenetic analysis that showed it to be closely related to, but genetically distinct from, the western Atlantic species Hexapanopeus angustifrons (Benedict & Rathbun, 1891). Hexapanopeus klausruetzleri n. sp. differs from this widely reported warm-temperate species in both its smoother carapace and pereopod surfaces and its generally more lobiform anterolateral teeth. The unique male first gonopod of the new species also strongly supports its morphological separation from all known congeners and other superficially similar western Atlantic panopeids with which it might be confused. To date, mature females have not been found, and the limited available collections are restricted to the vicinity of Carrie Bow Cay and nearby waters. Fourteen additional species of small panopeid and pseudorhombilid crabs, similar to Hexapanopeus klausruetzleri n. sp. in size and general habitus, were taken in the course of our studies in Belize. Most have not been previously reported from these waters, and several warrant further study to confirm their identifications.

Zoology↗

Fibrous anisotropy and mineral gradients within the radula stylus of chiton: Controlled stiffness and damage tolerance in a flexible biological composite

Over hundreds of millions of years, organisms have evolved architected structures via precise control over hierarchically assembled components, including the integration of dissimilar materials. One such example is found in the radula system of chitons, intertidal mollusks that feed on algae growing on the rock. Their radula consists of multiple rows of ultrahard teeth, each integrated with a foldable belt-like substrate via a stiff, yet flexible stylus, which is essential for efficient rasping during the feeding process. Here, we investigate the nano and micro-scale components and architectures as well as regional mechanical properties of the stylus, and their subsequent role during the rasping of Cryptochiton stelleri. Three important factors were determined to contribute to the regio-specific stiffness of the stylus: the presence of mineral components, highly oriented chitinous fibers, and a chemically cross-linked protein matrix. All these factors are varied throughout the stylus. There is a high mineral content on the trailing edge close to the tooth and a cross-linked matrix on the leading edge, both with orientational specific oriented chitin fibers that provide force transduction to the tooth. Conversely, there is a significant lack of mineral or cross-linked matrix in the proximal end as well as a low degree of fiber orientation, resulting in a flexible region that can accommodate torsion and flexure during rasping. Understanding the graded composite structure of the stylus and applying this unique design to various engineering fields such as soft robotics, biotechnology, and the medical industry, can inspire the production of high-performance materials.

Lee, Jung-Eun↗

Mineral Association Changes the Secondary Structure and Dynamics of Murine Amelogenin

Biomineralization proteins, present during the formation of hard tissues including bones, teeth, egg shells and nacre, result in the exquisite structures and properties of the resulting materials.[1] The structure of these proteins is often implicated in the control of the mineral properties, however very little structural data is available for the bulk of these proteins due to the difficulty in determining structures of immobilized proteins. Solid-state NMR is uniquely suited to the study of the structure of proteins bound to surfaces, demonstrated with the structural and orientation insights provided for the hydroxyapatite mineralization proteins statherin and the amelogenin, LRAP.[2] While these data are some of the only structural data available for this important class of protein, the experiments are often expensive and time consuming, due to the need to prepare and measure samples with isolated spin pairs, and are limited to a size of ~60 residues. In this work, we utilized a combination of 1D and recent 2D[3] solid-state NMR techniques along with a sparsely labelled sample to characterize the structure and dynamics of potential HAP binding residues of the 180 residue enamel protein, amelogenin. Amelogenin nanospheres and mineral bound amelogenin were investigated and a shift from unstructured to β-sheet structure was observed, along with a decrease in protein flexibility. This work provides the first molecular level structure and dynamic information of full-length amelogenin on the surface of hydroxyapatite (HAP) and within nanospheres, and demonstrates the ability to evaluate structural characteristics of large biomineralization proteins bound to their physiologically relevant surface. The research was performed at the Pacific Northwest National Laboratory (PNNL), a facility operated by Battelle for the U.S. Department of Energy, with a portion of it performed at the W.R. Wiley Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility sponsored by the U.S. DOE Biological and Environmental Research program.

59 BASIC BIOLOGICAL SCIENCES↗

Using Comparative Genomics for Inquiry-Based Learning to Dissect Virulence of Escherichia coli O157:H7 and Yersinia pestis

Genomics and bioinformatics are topics of increasing interest in undergraduate biological science curricula. Many existing exercises focus on gene annotation and analysis of a single genome. In this paper, we present two educational modules designed to enable students to learn and apply fundamental concepts in comparative genomics using examples related to bacterial pathogenesis. Students first examine alignments of genomes of Escherichia coli O157:H7 strains isolated from three food-poisoning outbreaks using the multiple-genome alignment tool Mauve. Students investigate conservation of virulence factors using the Mauve viewer and by browsing annotations available at the A Systematic Annotation Package for Community Analysis of Genomes database. In the second module, students use an alignment of five Yersinia pestis genomes to analyze single-nucleotide polymorphisms of three genes to classify strains into biovar groups. Students are then given sequences of bacterial DNA amplified from the teeth of corpses from the first and second pandemics of the bubonic plague and asked to classify these new samples. Learning-assessment results reveal student improvement in self-efficacy and content knowledge, as well as students' ability to use BLAST to identify genomic islands and conduct analyses of virulence factors from E. coli O157:H7 or Y. pestis. Each of these educational modules offers educators new ready-to-implement resources for integrating comparative genomic topics into their curricula.

59 BASIC BIOLOGICAL SCIENCES↗

Biomineral mesostructure

Abstract Biominerals formed by animals are most frequently calcium carbonate or phosphate polycrystalline materials with complex hierarchical structures. This article will focus on the 10-nm–10-µm scale, termed “mesoscale,” at which the “mesostructure” differs greatly across biominerals, is relevant to their mechanical properties, and reveals formation mechanisms in sea urchin teeth, mollusk shell prisms and nacre, human enamel, and coral skeletons. This article will conclude by focusing on important unanswered questions to inspire future research. Graphical abstract

36 MATERIALS SCIENCE↗

Morphological, Physiological, and Genetic Techniques for Improving Field Identification of Steelhead, Coastal Cutthroat Trout, and Hybrid Smolts

Abstract In streams with sympatric populations of steelhead Oncorhynchus mykiss and coastal cutthroat trout O. clarkii clarkii (hereafter, cutthroat trout), life history descriptions and smolt production estimates may be hampered by misclassification of hybrids as steelhead or cutthroat trout. Additionally, important morphological and physiological differences between hybrid and non-hybird smolts are often unknown. Therefore, we assessed field classification and created classification models to quantify and reduce misclassification rates among migrating steelhead, cutthroat trout, and hybrid smolts. Field misclassifications of smolts with steelhead or cutthroat trout genotypes were low (1% and 2%, respectively). However, field misclassification of fish with hybrid genotypes was high, with 11% of the hybrids being misclassified as steelhead and 42% of the hybrids being misclassified as cutthroat trout. Hybrid smolts were larger, had lower gill Na+, K+-ATPase activities, and lower condition factors than steelhead but were similar to cutthroat trout smolts in these same measurements. Additionally, statistical classification analyses using morphological traits including subterminal jaw slash intensity, hyoid teeth presence, maxillary length, breaks of pigment along outer margin of adipose fin, condition factor, and migration date improved classification error rates of hybrids from 53% to 21%. In systems with sympatric populations of steelhead and cutthroat trout, we recommend a thorough evaluation of field-based identification methods with genetic techniques to assess the effectiveness of field-based classification in addition to examining important life history differences among steelhead, cutthroat trout, and their hybrids.

Kennedy, Benjamen M.↗

Methodology for Scaling Fusion Power Plant Availability

Normally in the U.S. fusion power plant conceptual design studies, the development of the plant availability and the plant capital and operating costs makes the implicit assumption that the plant is a 10th of a kind fusion power plant. This is in keeping with the DOE guidelines published in the 1970s, the PNL report1, "Fusion Reactor Design Studies - Standard Accounts for Cost Estimates. This assumption specifically defines the level of the industry and technology maturity and eliminates the need to define the necessary research and development efforts and costs to construct a one of a kind or the first of a kind power plant. It also assumes all the "teething" problems have been solved and the plant can operate in the manner intended. The plant availability analysis assumes all maintenance actions have been refined and optimized by the operation of the prior nine or so plants. The actions are defined to be as quick and efficient as possible. This study will present a methodology to enable estimation of the availability of the one of a kind (one OAK) plant or first of a kind (1st OAK) plant. To clarify, one of the OAK facilities might be the pilot plant or the demo plant that is prototypical of the next generation power plant, but it is not a full-scale fusion power plant with all fully validated "mature" subsystems. The first OAK facility is truly the first commercial plant of a common design that represents the next generation plant design. However, its subsystems, maintenance equipment and procedures will continue to be refined to achieve the goals for the 10th OAK power plant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Bioinspired mineralizing microenvironments generated by liquid-liquid phase coexistence

Biominerals such as bones, teeth and shells exhibit improved mechanical properties and intricate morphologies not seen in nonbiologically-produced minerals of ostensibly the same composition. These remarkable properties of biogenic minerals are thought to arise due to precise local control over the mineral deposition process, including organic and inorganic inclusions. Understanding how Biology controls the local reaction environment during formation of these materials to control their composition, structure, and properties is a grand challenge that promises to enable new routes to high-performance materials. This project developed multi-compartment bioinspired microreactors as artificial mineralizing vesicles, and used them to understand and control formation of inorganic/organic composite solid materials. A major emphasis was on developing all-aqueous emulsions in which each droplet was a structured microreactor with two or more adjacent phases. This approach provided local control over reaction environment including availability of inclusions such as polypeptides and metal ions, while being sufficiently simple to produce large populations of essentially identical multiphase reactor droplets simultaneously within a batch. Organic/inorganic composite materials could be produced with very high organic content that stabilized the inorganic portions as amorphous materials (e.g., amorphous calcium carbonate) by preventing the typical conversion to more thermodynamically crystalline forms (e.g., calcite). These stabilized amorphous composites could be stored indefinitely and converted to crystalline forms later by removal of the organic inclusions via, for example, heating. Compositional gradients in the organic and inorganic components were embedded during synthesis due to the evolution of the reaction microenvironment, and despite the complexity of this process it occurred similarly across the population of reactive droplets and was hence encoded into the population of resulting composite particles. The approach developed here allows pre-structuring of reactive microenvironments to control the spatiotemporal reaction environment, which is an important step towards rational design and on-demand production of complex functional materials with desired composition, optical properties, and mechanical response.

36 MATERIALS SCIENCE↗

Gear Test Assembly – Report Experimental Testing and Gear Analysis (FY2021 Midyear Report)

The Gear Test Assembly (GTA) has completed three experimental campaigns at the Mechanisms Engineering Test Loop (METL) facility. The most recent campaign tested Inconel 718 spur gears, tapered roller bearings of 52100 bearing steel with no heat treatment, and a lantern ring shaft seal with spring-loaded fasteners. Testing was performed in Test Vessel 1 (TV1) with 250°C sodium that had an oxide concentration of <10ppm. Testing began in February 2021 and was ended in March 2021 when a thrust bearing assembly failed, requiring shutdown and maintenance. The third experimental campaign completed 1,568 simulated fuel assembly maneuvers before the thrust bearing failure. The GTA was removed from TV1 and cleaned in the Carbonation System. The GTA is currently being prepared for the next experimental campaign. Nondestructive examination methods have been developed at Argonne to monitor the health of the GTA spur gears. Eddy current testing (ECT) and ultrasonic testing (UT) were performed prior to sodium testing and after each experimental campaign. The NDE has shown that the primary damage mechanism is mechanical wear on the gear tooth surface. Several larger nicks are observable on the gear faces, with additional large nicks present on the edges of the gear teeth. While this damage is observable, the overall health of the gears is adequate for more in-sodium testing. A total of 12,752 simulated fuel assembly maneuvers have been completed using this set of gears.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Bio-Based Phase Change Materials (PCMs) for Thermal Energy Storage (Final Scientific/Technical Report)

The goal of this project is to develop a novel bio-based phase change material (PCM) derived from squid ring teeth (SRT) proteins, and design a prototype heat exchanger based on these bio-based PCMs for energy storage and dynamic heat exchange for building thermal energy storage systems. The PCMs, derived from SRT proteins, will demonstrate room temperature energy storage capacities and switchable thermal conductivities that redefine the current state-of-the-art (SOA) for building thermal energy storage. Further, in a single material and with a single manufacturing processes, our proposed thermal battery will be developed with “on demand” thermal conductivity for rapid charging/discharging but superior insulation during energy storage periods. More specifically, our bio-based PCMs have demonstrated: 1) the potential for increased energy storage capacity (i.e., greater than paraffines at room temperature); 2) tunability in thermal conductivity with the largest thermal conductivity switching ratios for an intrinsic material reported to date, and 3) a 100% recyclable and biodegradable PCM with low volatility and toxicity and scalability in its manufacture for both residential and commercial applications. The already established ability for roll-to-roll processing of these non-toxic, non-flammable SRT composites along with their carbon-neutral manufacturing processes that has been pioneered by our team make this solution a disruptive and impactful technology to redefine the current SOA of energy storage technologies. The outcomes of this effort have been: 1) the identification of new bio-based PCM that establishes a new SOA for thermal conductivity and energy storage density at room temperature and 2) the development of a new experimental technique to measure the energy storage density via latent heat measurements during melting of thin films. This new technique can be applied to thin films (as thin as < 1 micrometer), and represents a novel approach for thin film energy storage density measurements. Dynamic thermal energy storage is the missing technology that will enable a grid- interactive efficient building (GEB). For a “smart” building capable of connecting with the power grid, the media must be inexpensive and possess thermal switching capabilities to control the time-dependent heat flow into (and out of) the PCM on demand. Unique to the material system in this program, programmable SRT-based PCM show improvements as compared to traditionally used PCMs, and thus its technical performance will represent a leap forward for the future GEB concept.

25 ENERGY STORAGE↗

Triaxial Shear Tests on Simulated Sierra White Fault Gouge & Borehole Simulation in Sierra White Gouge

Laboratory shear tests were conducted on pulverized Sierra White granite (SWG) to investigate slip mechanisms in naturally occurring faults. Synthetic fault geometries were constructed by sandwiching fine grained SWG powder in between steel forcing blocks. For dry experiments, ~3.5 g of SWG powder was poured onto the face of the lower steel forcing block and leveled. For saturated experiments, enough fluid was added to the ~3.5 g of Sierra White granite powder to form a slurry. This slurry was applied to the lower forcing block and leveled. Inclined forcing blocks with 25.4 mm diameter and 35° faces, which were machined from ground steel rods with fine teeth on the faces, help to hold the gouge in place and prevent delamination at the interface. The top forcing block had a 2.03 mm centered hole to allow pore fluid access to the gouge. A fine steel mesh prevented back flow of the gouge into pore fluid lines. Samples were isolated from the confining medium using three layers of heat shrink polyolefin, as shown in Figure 1. The outer layer was shrunk over the o-rings on the end caps to form an impermeable seal, which was reinforced with steel tie wires on both sides of the o-rings. Hardened steel spacers and copper shim stock was placed between the steel forcing blocks and the end caps to preserve the parallelism of the Hastelloy wetted parts. For dry samples, the end caps were plugged, while the end caps for the saturated samples were connected to pore lines.

58 GEOSCIENCES↗

Gear Test Assembly - Experimental Testing and Analysis of Gears and Bearings - FY2026

The Gear Test Assembly (GTA) is an experimental test apparatus built and installed in the Mechanisms and Engineering Test Loop (METL) at Argonne National Laboratory (ANL). While designed to accommodate a variety of components intended for use in advanced compact in-vessel transfer machine, the focus of GTA been the testing of large radial spur gears. The performance of the components used in GTA motivates the choices made in the design, components, and material choices for the forthcoming METL test articles; the Gripper Test Assembly (GrTA), and the Bearing Test Assembly (BTA). To date, GTA has completed nine experimental testing campaigns and achieved over 21 million revolutions under prototypic sodium fast reactor loads and operating conditions. This report provides an overview and results for the two most recent experiments Campaign #8 and Campaign #9. `Campaign #8 was the first campaign to make use of a set of nickel alloy radial spur gears, made from Hastelloy C-22HS, and combined with heat-treated tapered roller bearings. The bearings and torque profile used allowed Campaign #8 to be directly compared with Campaign #1 where Inconel 718 gears were used instead. Campaign #8 attained 1,058,880 shaft revolutions within 23% of the 1,314,855 revolutions achieved in Campaign #1. These results demonstrate that the heat-treated tapered roller bearings show consistent increased lifetimes, approximately three times longer than for non heat-treated taper rollers, and that the particular material of the gear does not play a substantial role in performance. Similar to Campaign #7 where bearing failure resulted in fragmentation and transport of bearing material into the gear teeth led to tooth damage in the Inconel gears, a similar process led to the damage of the Hastelloy gears. Subsequent NDE analysis showed that the damage was only limited to the tooth surface and does not extend into the gear interiors. Based on the NDE reports, the Hastelloy gears can be reconditioned and put back into service for future campaigns as was done for the Inconel gears. Reconditioned Inconel 718 gears damaged in Campaign #7 were returned to service in Campaign #9 and paired with non heat-treated tapered roller bearings. In Campaign #9 a novel set of operating conditions were implemented whereby the gears and bearings were cycled between hot, submerged refueling conditions where fuel handling operations occurred and cold, dry, and inert conditions where the sodium was drained and the vessel was allowed to cool simulating long, ex-vessel storage of the fuel handling machine. A total of eight of these operating cycles were achieved before a bearing failure occurred after the accumulation of 475,692 shaft revolutions were achieved. During Campaign #9, one of the drive motors was damaged and over the course of a 240 day standby period, the entire GTA drive system was upgraded from a 480VAC system to a 240VAC system that provided the opportunity to consolidate wall-space in the METL facility and provide more space for additional test articles being installed in the coming year. The over 475,000 shaft revolutions achieved in Campaign #9 eclipses the previous record for lifetime of non heat-treated tapered roller bearings held by Campaign #3 of 392,000 shaft revolutions. Further analysis and future campaigns hope to shed light on the cause of this approximately 17% increase in lifetime.

42 ENGINEERING↗

Single-turn worm mills for conical round-tooth gears

Facets must be machined at the end of gear teeth. The shaping of facets by single-turn worm mills is considered in detail. Deficiencies are found in familiar design methods for such mills. Formulas are proposed for the calculation of single-turn worm mills used in machining conical round-tooth gears.

42 ENGINEERING↗

Investigation of Cutter–Woodchip Contact Pressure in a New Biomass Comminution System

A Crumbler ® rotary shear system was recently developed to process fuel-grade woodchips into feedstocks having more uniform particle sizes for improved flowability and higher thermochemical output yield than a traditional hammer mill. It represents a significant innovation in the state of the art of biomass comminution equipment. However, the milling unit has experienced significant abrasive wear of the feeding teeth and cutters when processing hard and dusty feedstocks, such as logging residue and corn stover. Here, we present initial simulation results from a finite-element stress analysis of the rotary shear, which is used to investigate the dynamics of interaction between the cutters and woodchips. This is the first step for optimizing the cutter design to improve the system lifetime and processing efficiency, thus reducing downtime and improving overall productivity.

42 ENGINEERING↗