Search NASA⌕ Search

SEARCH · Search NASA

Results for “temperature programmed desorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Effect of ZSM-5 acidity on aromatic product selectivity during upgrading of pine pyrolysis vapors

The impact of catalyst acidity on the selectivity of upgraded biomass pyrolysis products was studied by passing pine pyrolysis vapors over five ZSM-5 catalysts of varying acidity at 500 degrees C. The SiO 2 -to-Al 2 O 3 ratio (SAR) of the ZSM-5 zeolite was varied from 23 to 280 to control the acidity of the catalyst and the composition of upgraded products. The upgraded product stream was analyzed by GCMS. Additionally, catalysts were characterized using temperature programmed desorption, diffuse-reflectance FTIR spectroscopy, N 2 physisorption, and X-ray diffraction. The results showed that the biomass pyrolysis vapors were highly deoxygenated to form a slate of aromatic hydrocarbons over all of the tested ZSM-5 catalysts. As the overall acidity of the ZSM-5 increased the selectivity toward alkylated (substituted) aromatics (e.g., xylene, dimethyl-naphthalene, and methyl-anthracene) decreased while the selectivity toward unsubstituted aromatics (e.g., benzene, naphthalene, and anthracene) increased. Additionally, the selectivity toward polycyclic aromatic compounds (2-ring and 3-ring) increased as catalyst acidity increased, corresponding to a decrease in acid site spacing. The increased selectivity toward less substituted polycyclic aromatic compounds with increasing acidity is related to the relative rates of cyclization and alkylation reactions within the zeolite structure. As the acid site concentration increases and sites become closer to each other, the formation of additional cyclization products occurs at a greater rate than alkylated products. The ability to adjust product selectivity within 1-, 2-, and 3-ring aromatic families, as well as the degree of substitution, by varying ZSM-5 acidity could have significant benefits in terms creating a slate of upgraded biomass pyrolysis products to meet specific target market demands.

09 BIOMASS FUELS↗

Correlating furfural reaction pathways with interactions between furfural and monometallic surfaces

Controlling the selectivity of furfural reaction is an important step towards valorizing this important platform chemical in biomass conversion. Previous studies speculate that the selectivity of furfural reaction depends on the interactions of furan ring with metal surfaces. In this work, high resolution electron energy loss spectroscopy (HREELS) and temperature programmed desorption (TPD) are employed to directly study the correlations between furfural reaction pathways and interactions between furfural and different monometallic surfaces. Monometallic surfaces with strong ring interactions favor ring-opening products, while monometallic surfaces with weak ring interactions favor furan production. Oxophilic metal surface like Fe(110) promotes the hydrodeoxygenation pathway to produce 2-methylfuran due to strong interaction with the carbonyl group. Furthermore, these results should provide guidance in the future catalyst design for converting furfural to value-added products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental and Computational Studies of the Production of 1,3-Butadiene from 2,3-Butanediol Using SiO2-Supported H3PO4 Derivatives

Silica-supported phosphoric acid and metal phosphate catalyzed 1,3-butadiene (BDE) production from 2,3-butanediol (2,3-BDO) was studied using experimental and computational techniques. The catalyst was initially tested in a continuous flow reactor using commercially available 2,3-BDO, leading to maximum BDE yields of 63C%. Quantum chemical mechanistic studies revealed 1,2-epoxybutane is a kinetically viable and thermodynamically stable intermediate, supported by experimental demonstration that this epoxide can be converted to BDE under standard reaction conditions. Newly proposed E2 and SN2' elementary steps were studied to rationalize the formation of BDE and all detected side-products. Additionally, using quantum mechanics/molecular mechanics (QM/MM) calculations, we modeled silica-supported phosphate catalysts to study the effect of the alkali metal center. Natural population analysis showed that phosphate oxygen atoms are more negatively charged in CsH2PO4/SiO2 than in H3PO4/SiO2. In combination with temperature-programmed desorption experiments using CO2, the results of this study suggest that the improved selectivity achieved when adding the metal center is related to an increase in the basicity of the catalyst.

butadiene↗

Adsorption of NO on Fe 3 O 4 (111)

Adsorption of NO on Fe 3 O 4 (111) is studied by density functional theory (DFT) calculations. NO is prefer-ably adsorbed atop the octahedral site which has a clearly higher adsorption energy than the tetrahedral site. The difference in adsorption energy correlates with differences in adsorption geometries and NO stretch vibrations. Here, the results are in good agreement with temperature programmed desorption (TPD)and reflection-adsorption IR spectroscopy (RAIRS) measurements and provide an explanation of the observation of only one vibrational mode despite two distinct TPD features.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lithium promotion of Pt/m-ZrO 2 catalysts for low temperature water-gas shift

Low temperature water-gas shift (LTS) is an important reaction occurring in a fuel processor for producing and purifying hydrogen. Platinum supported on m-ZrO 2 belongs to a family of catalysts consisting of metal nanoparticles and an active partially reducible oxide, with the catalysis proposed to occur at the boundary between metal particles and the support. In this investigation, increasing the loading of lithium dopant increased the LTS rate up to 0.54 wt % lithium, where conversion was 2.4 times that of the unpromoted catalyst at 260°C. Further increases in lithium loading up to 1.5 wt % decreased the rate, although it remained higher than that of the unpromoted catalyst. Infrared spectroscopy and CO 2 temperature programmed desorption experiments showed three effects with increasing lithium loading: (1) lithium promoter weakened the C–H bond of formate, the proposed rate limiting step of the interfacial surface formate mechanism; (2) high levels of lithium suppressed the platinum site capacity required for hydrogen transfer; and (3) high levels of lithium increased catalyst basicity. Aspects (2) and (3) tended to inhibit desorption of product CO 2 , an acidic molecule the removal of which is metal-catalyzed. XANES and XPS experiments revealed that electron transfer to enrich Pt nanoparticles is unlikely the root cause of C–H bond weakening in formate. However, other electronic effects (e.g., electrostatic effects or molecular rearrangement due to enhanced basicity) were not ruled out.

08 HYDROGEN↗

Correlation of Pt-Re Surface Properties with Reaction Pathways for the Aqueous-Phase Reforming of Glycerol

The surface properties of Pt-Re catalytic nano-particles supported on carbon following exposure to a hydrogen reducing environment and subsequent hydrothermal conditions have been studied using in-situ X-ray photoelectron spectroscopy (XPS) and ammonia temperature programmed desorption (TPD). These properties have been correlated with the catalyst selectivity for the aqueous phase reforming of glycerol. We show that Pt in reduced Pt-Re/C becomes electron deficient, and a fraction of the Re becomes oxidized when the catalyst is subsequently exposed to hydrothermal reaction conditions. Oxidation of Pt-Re generates surface acidity, which drastically affects the reaction pathways. The acid site concentration, but not acid site strength, increases with Re loading. This acidity increase with Re addition favors C-O over C-C cleavage, which results in higher selectivity to liquid products and alkanes at the expense of hydrogen production. We propose a model for the Pt-Re active site and the origin of acidity enhanced by the addition of Re.

08 HYDROGEN↗

Distinct water activation on polar/non-polar facets of ZnO nanoparticles

ZnO nanoparticles with differing dominant facets were prepared and characterized by a complimentary of techniques such as X-ray diffraction, electron microscopy, temperature programmed desorption of H2O, and Fourier transform infrared spectroscopy analysis of adsorbed D2O. For the first time, water interaction/activation is compared on ZnO polar and non-polar facets. We report that non-polar facets exhibit high activity in water activation, which favors reactions such as ketonization and steam reforming in which dissociated water is involved. The distinct water dissociation on ZnO non-polar facets could be related to its facile formation of oxygen vacancies under realistic reaction conditions.

Environmental Molecular Sciences Laboratory↗

Hydrogen activation by rhodium under the cover of a copper oxide thin film

Here, the activation of reactants by catalytically active metal sites at metal-oxide interfaces is important for understanding the effect of metal-support interactions on nanoparticle catalysts and for tuning activity and selectivity. Using a combined experimental and theoretical approach, we studied the activation of H 2 and the effect of CO poisoning on isolated Rh atoms completely or partially covered by a copper oxide (Cu 2 O) thin film. Temperature-programmed desorption (TPD) experiments conducted in ultra-high vacuum (UHV) show that neither a partially nor a fully oxidized Cu 2 O layer grown on a Rh/Cu(111) single-atom alloy can activate hydrogen in UHV. However, in situ ambient pressure X-ray photoelectron spectroscopy (AP-XPS) experiments performed at elevated H 2 pressures reveal that Rh significantly accelerates the reduction of these Cu 2 O thin films by hydrogen. Remarkably, the fastest reduction rate is observed for the fully oxidized sample with all Rh sites covered by Cu 2 O. Both TPD and AP-XPS data demonstrate that these covered Rh sites are inaccessible to CO, indicating that Rh under Cu 2 O is active for H 2 dissociation but cannot be poisoned by CO. In contrast, an incomplete oxide film leaves some of the Rh sites exposed and accessible to CO, and hence prone to CO poisoning. Density functional theory calculations demonstrate that unlike many reactions in which hydrogen activation is rate limiting, the rate-determining step in the dissociation of H 2 on thin-film Cu 2 O with Rh underneath is the adsorption of H 2 on the buried Rh site, and once adsorbed, the dissociation of H 2 is barrierless. These calculations also explain why H 2 can only be activated at higher pressures. Together, these results highlight how different the reactivity of atomically dispersed Rh in Cu can be depending on its accessibility through the oxide layer, providing a way to engineer Rh sites that are active for hydrogen activation but resilient to CO poisoning.

36 MATERIALS SCIENCE↗

Effects of Water Vapor on the Reactivity of Aluminosilicates in Vapor-Phase Propanal Aldol Condensation

Aluminosilicate materials have been extensively studied as efficient aldol catalysts for C-C coupling reactions due to their acidic nature, high surface area, thermal stability, and porous structure. This work investigated the impact of water vapor pressure on the catalytic reactivity of aluminosilicates for the aldol condensation of propanal to 2-methyl-2-pentenal (MP). The catalytic performance of amorphous SiO2-Al2O3 (A-Si-Al) and aluminated MCM-41 (Al-MCM-41) for the vapor-phase aldol condensation of propanal was evaluated at 200 degrees C as a function of vapor-phase water content at atmospheric pressure. Our findings demonstrate that co-feeding low water vapor pressures (1-18 kPa) with propanal enhances the rates of MP production at 200 degrees C on A-Si-Al. Conversely, water vapor pressures of 25 kPa result in a decrease in aldol dimer formation rates. The rate of MP production evaluated on Al-MCM-41 also increased in the presence of 5 kPa water compared to anhydrous conditions. Propylamine temperature-programmed desorption analyses revealed an increase in Bronsted acid site density when both catalysts were exposed to water, which likely accounts for the observed enhancement in aldol condensation reactivity under hydrous conditions. Reversibility testing of the water vapor effect under reaction conditions, combined with X-ray diffraction analysis of fresh, spent, and regenerated catalysts, revealed no structural changes in either aluminosilicate upon exposure to water or reaction conditions. The rates of aldol condensation and the impact of water vapor were highly consistent across both materials, suggesting that zeolite crystallinity has minimal influence on the catalytic performance.

acid catalysts↗

Spreading of lithium on a stainless steel surface at room temperature

Lithium conditioned plasma facing surfaces have lowered recycling and enhanced plasma performance on many fusion devices and liquid lithium plasma facing components are under consideration for future machines. A key factor in the performance of liquid lithium components is the wetting by lithium of its container. We have observed the surface spreading of lithium from a mm-scale particle to adjacent stainless steel surfaces using a scanning Auger microprobe that has elemental discrimination. Here, the spreading of lithium occurred at room temperature (when lithium is a solid) from one location at a speed of 0.62 μm/day under ultrahigh vacuum conditions. Separate experiments using temperature programmed desorption (TPD) investigated bonding energetics between monolayer-scale films of lithium and stainless steel. While multilayer lithium desorption from stainless steel begins to occur just above 500 K (E des = 1.54 eV), sub-monolayer Li desorption occurred in a TPD peak at 942 K (E des = 2.52 eV) indicating more energetically favorable lithium-stainless steel bonding (in the absence of an oxidation layer) than lithium lithium bonding.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scandium functionalized carbon aerogel: Synthesis of nanoparticles and structure of a new ScOCl and properties of NaAlH{sub 4} as a function of pore size

A new method for scandium-functionalization of carbon aerogels forming nanoparticles of a new scandiumoxochloride, ScOCl is presented. Sodium aluminiumhydride, NaAlH{sub 4}, is successfully melt infiltrated into the nano porous scaffolds with pore sizes of D{sub max}=7, 10, 13, 21, 26 and 39 nm, containing scandium based nano particles (<2.9 wt%) confirmed by elemental analysis and scanning electron microscopy. A systematic study of hydrogen storage properties of the nano composite materials is presented. An aqueous solution of ScCl{sub 3} was initially infiltrated and formed nanoconfined [Sc(OH)(H{sub 2}O){sub 5}]{sub 2}Cl{sub 4}(H{sub 2}O){sub 2}, which transforms to nanoparticles of a new scandium oxochloride, ScOCl at 192 °C and to Sc{sub 2}O{sub 3} at 420 °C. ScOCl crystallizes in an orthorhombic unit cell a=3.4409(8), b=3.9613(6) and c=8.178(2) Å, space group Pmmn, and is built from layers of [ScO{sub 4}Cl{sub 2}] octahedra forming neutral ScOCl layers. Temperature programmed desorption mass spectroscopy shows slightly improved kinetics for release of hydrogen with decreasing pore size. Continuous cycling of hydrogen release and uptake measured by the Sieverts' method reveal a larger preserved hydrogen storage capacity for scandium-functionalized aerogel with the larger pores (39 nm). - Highlights: • New synthesis approach for nanoporous Sc-functionalization carbon aerogel (Sc-CA). • The new scandium oxochloride, ScOCl, structure is obtained. • NaAlH{sub 4} nanoconfined in Sc-CA with pores ranging between 7 nm<D{sub max}<39 nm. • Improved H{sub 2} release kinetics obtained with decreasing pore size. • Nanoconfinement (D{sub max}=39 nm) retains 71% of the H{sub 2} capacity after four cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microwave-assisted fast vapor-phase transport synthesis of MnAPO-5 molecular sieves

MnAPO-5 was prepared by a microwave-assisted vapor-phase transport method at 180 deg. C in short times. The products were characterized by X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectra, UV-vis spectroscopic measurement, NH{sub 3}-temperature-programmed desorption and esterification reaction. It was found that dry gels prepared with aluminum isopropoxide, phosphoric acid and manganese acetate could be transferred to MnAPO-5 in the vapors of triethylamine and water by the microwave-assisted vapor-phase transport method at 180 deg. C for less than 30 min. The crystallization time was greatly reduced by the microwave heating compared with the conventional heating. The resulting MnAPO-5 exhibited much smaller particle sizes, higher surface areas and slightly higher catalytic activity in the esterification of acetic acid and butyl alcohol than those prepared by the conventional vapor-phase transport method and hydrothermal synthesis.

36 MATERIALS SCIENCE↗

Effect of H{sub 3}PW{sub 12}O{sub 40} impregnation on Sn-MCM-41 mesoporous molecular sieves and their physico-chemical properties

Graphical abstract: The wide angle XRD shows the well dispersion of HPWA in Sn-MCM-41. It enhances the total acidity of the material. The acidity of the material is correlated with sulfone selectivity. The FT-IR of dibenzothiophene and product shows the formation of sulfone (DBTO{sub 2}). - Highlights: • To enhance the total acidity of Sn-MCM-41 TPA is impregnated. • FT-IR and {sup 31}P MAS NMR confirms the HPWA intact on Sn-MCM-41. • EDAX shows the presence of W and P on Sn-MCM-41. • In ODS formation of sulfone was confirmed by FT-IR and {sup 1}H NMR. • The order of the catalytic activity of the catalysts are 18HSnM > 28HSnM > 8HSnM. - Abstract: Si-Sn-MCM-41 (Si/Sn = 110) mesoporous molecular sieve was synthesized by hydrothermal sol–gel method using cetyltrimethylammonium bromide (CTAB) as surfactant and SnCl{sub 4}·5H{sub 2}O as a metal source. To generate surface acidity of Si-Sn-MCM-41, 12-tungstophosphoric acid (HPWA) is impregnated on it. The acidity of HPWA loading on Sn-MCM-41 was investigated by temperature programmed desorption of NH{sub 3}. The diffused reflectance spectra of ultraviolet radiation, Raman spectra, FT-IR, {sup 29}Si-MAS NMR and {sup 31}P-MAS NMR techniques revealed the intact of α-Keggin anions on Sn-MCM-41. The wide angle XRD results showed that the HPWA is well dispersed on the support. The total acidity was enhanced with increase in loading of H{sub 3}PW{sub 12}O{sub 40}. The catalytic activity was examined in desulfurization of dibenzothiophene in vapor phase system. Among the catalysts 18% HPWA loaded Sn-MCM-41 showed good catalytic activity in desulfurization at 325 °C. The HPWA/Sn-MCM-41 are a suitable solid acid catalyst for converting organic sulfur into insoluble sulfone.

36 MATERIALS SCIENCE↗