Search NASA⌕ Search

SEARCH · Search NASA

Results for “test data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Measurement of local convective heat transfer coefficients from a smooth and roughened NACA-0012 airfoil - Flight test data

Wind tunnels typically have higher free stream turbulence levels than are found in flight. Turbulence intensity was measured to be 0.5 percent in the NASA Lewis Icing Research Tunnel (IRT) with the cloud making sprays off and around 2 percent with cloud making equipment on. Turbulence intensity for flight conditions was found to be too low to make meaningful measurements for smooth air. This difference between free stream and wind tunnel conditions has raised questions as to the validity of results obtained in the IRT. One objective of these tests was to determine the effect of free stream turbulence on convective heat transfer for the NASA Lewis LEWICE ice growth prediction code. These tests provide in-flight heat transfer data for a NASA-0012 airfoil with a 533 cm chord. Future tests will measure heat transfer data from the same airfoil in the Lewis Icing Research Tunnel. Roughness was obtained by the attachment of small, 2 mm diameter hemispheres of uniform size to the airfoil in three different patterns. Heat transfer measurements were recorded in flight on the NASA Lewis Twin Otter Icing Research Aircraft. Measurements were taken for the smooth and roughened surfaces at various aircraft speeds and angles of attack up to four degrees. Results are presented as Frossling number versus position on the airfoil for various roughnesses and angles of attack.

Van Fossen, G. James↗
NASA NTRS2002

Lobed Mixer Design for Noise Suppression Acoustic and Aerodynamic Test Data Analysis

A comprehensive database for the acoustic and aerodynamic characteristics of several model-scale lobe mixers of bypass ratio 5 to 6 has been created for mixed jet speeds up to 1080 ft/s at typical take-off (TO) conditions of small-to-medium turbofan engines. The flight effect was simulated for Mach numbers up to 0.3. The static thrust performance and plume data were also obtained at typical TO and cruise conditions. The tests were done at NASA Lewis anechoic dome and ASK's FluiDyne Laboratories. The effect of several lobe mixer and nozzle parameters, such as, lobe scalloping, lobe count, lobe penetration and nozzle length was examined in terms of flyover noise at constant altitude. Sound in the nozzle reference frame was analyzed to understand the source characteristics. Several new concepts, mechanisms and methods are reported for such lobed mixers, such as, "boomerang" scallops, "tongue" mixer, detection of "excess" internal noise sources, and extrapolation of flyover noise data from one flight speed to different flight speeds. Noise reduction of as much as 3 EPNdB was found with a deeply scalloped mixer compared to annular nozzle at net thrust levels of 9500 lb for a 29 in. diameter nozzle after optimizing the nozzle length.

Mengle, Vinod G.↗
NASA NTRSDate not supplied

Refined Predictions Compared with the Propulsion Airframe Aeroacoustics and Aircraft System Noise Flight Research Test Data

In a collaboration between NASA and The Boeing Company, the Propulsion Airframe Aeroacoustics and Aircraft System Noise Flight Research Test was executed by the Boeing ecoDemonstrator Program in 2020 with an Etihad Airways Boeing 787-10 aircraft. This ambitious flight research successfully accomplished many objectives and constitutes the most comprehensive and highest quality acoustic flight data available to NASA for a modern commercial subsonic transport aircraft. One purpose of these data is to be the measure of accuracy for the aircraft system noise prediction capabilities of NASA. This research reviews the impact of the major improvements in prediction methods implemented up to this point and tested in the Research version of the NASA Aircraft Noise Prediction Program. The improvements have been to the prediction of jet source and jet-flap interaction, to both fan broadband and tone source prediction, and to the prediction of propulsion airframe aeroacoustic scattering effects. In general, over the engine power range, comparisons between prediction and flight data are within 2 EPNdB including for the intentional sideline-to-sideline asymmetries as implemented in the flight test by flying the aircraft with only one engine at power. Considerable progress has been shown here in the continuing effort to advance the fidelity of NASA aircraft noise prediction capabilities for subsonic aircraft flight acoustics, modern transport aircraft and future aircraft concepts.

aircraft system noise prediction↗
NASA NTRS1992

Program Handles Environmental-Test Data

S3 Data Acquisition and Control System, (S3DACS) monitors, controls, and records information acquired during tests and presents it in various formats for easy access by large number of users. Results automatically stored. Data used in computations, and selectively presented in tabular, graphical, or electronic form. Reports show current or historical events. Network software written in FoxPro/LAN 1.02 and 80386 Assembler.

De Freitas Bart, Frances↗
NASA NTRS1992

Middeck zero-gravity dynamics experiment - Comparison of ground and flight test data

An analytic and experimental study of the changes in the modal parameters of space structural test articles from one- to zero-gravity is presented. Deployable, erectable, and rotary modules was assembled to form three one- and two-dimensional structures, in which variations in bracing wire and rotary joint preload could be introduced. The structures were modeled as if hanging from a suspension system in one gravity, and unconstrained, as if free floating in zero-gravity. The analysis is compared with ground experimental measurements, made on a spring/wire suspension system with a nominal plunge frequency of one Hertz, and with measurements made on the Shuttle middeck. The degree of change in linear modal parameters as well as the change in nonlinear nature of the response is examined. Trends in modal parameters are presented as a function of force amplitude, joint preload, and ambient gravity level.

Crawley, Edward F.↗
NASA NTRS2010

Analysis of Flash Lidar Field Test Data for Safe Lunar Landing

In May 2008, the Autonomous Landing and Hazard Avoidance Technology (ALHAT) Project conducted a helicopter field test of a commercial flash lidar to assess its applicability to safe lunar landing. The helicopter flew several flights, which covered a variety of slant ranges and viewing angles, over man-made and natural lunar-like terrains. The collected data were analyzed to assess the performance of the sensor and the performance of two algorithms: Hazard Detection (HD) and Hazard Relative Navigation (HRN). The collected flash lidar data were also used to validate a high fidelity flash lidar software model used in ALHAT Monte Carlo simulations. The field test results, combined with prior simulation results, advanced the technology readiness level of the HD algorithm to TRL 5 and the HRN algorithm to TRL 4.

hazard relative navigation↗
NASA NTRS2015

Reducing the Effect of Transducer Mount Induced Noise on Aeroacoustic Wind Tunnel Testing Data with a New Transducer Mount Design

Characterization of launch vehicle unsteady aerodynamics is a field best studied through experimentation, which is often carried out in the form of large scale wind tunnel testing. Measurement of the fluctuating pressures induced by the boundary layer noise is customarily made with miniature pressure transducers installed into a model of the vehicle of interest. Literature shows that noise level increases between two to five decibels (dB referenced to 20 micropascal) can be induced when the transducer surface is not mounted perfectly flush with the model outer surface. To reduce this artificially induced noise, special transducer holders have been used for aeroacoustic wind tunnel testing by NASA. This holder is a sleeve into which the transducer fits, with a cap that allows it to be mounted in a recessed hole in the model. A single hole in the holder allows the transport of the tunnel medium so the transducer can discriminate the fluctuating pressure due to the turbulent boundary layer noise. The holder is first dry fitted into the model and any difference in height between the holder and the model surface can be sanded flush. The holder is then removed from the model, the transducer glued inside the holder, and the holder replaced in the model, secured also with glue, thus eliminating the problem of noise level increases due to lack of flushness. In order to work with this holder design, special transducers have been ordered with their standard screen removed and the diaphragm moved as close to the top of the casing as possible to minimize any cavity volume. Although this greatly reduces induced noise due to the transducers being out of flush, the holders can also induce a cavity resonance that is usually at a very high frequency. This noise is termed transducer mount induced noise (XMIN). The peak of the mode can vary with the cavity depth, boundary layer noise that can excite the mode, tunnel flow medium, and the build of the transducers. Because the boundary layer flow interaction with the microphone holder seems to have some effect on the cavity resonance response, the NASA/Marshall Space Flight Center (MSFC) aeroacoustic team postulated that changing the design of the holder might reduce the cavity resonance response. An experiment was performed at the MSFC Trisonic Wind Tunnel comparing a new holder design with the traditional MSFC holder. The new holder design is intended to mimic the Kulite Semiconductors, Inc. B-screen, where the single hole of the traditional MSFC holder is replaced by a series of ten 0.007 inch diameter holes. This particular design serves to protect the transducer diaphragm as in the manufacturer's B-screen, but also increases the frequency of the XMIN such that it is not apparent in the data collected from aeroacoustic wind tunnel tests. MSFC compared the two holder designs by installing two transducers in standard holders on one side of a ten inch long ten degree cone, and two transducers in B-screen holders on the opposite side for a series of runs at different conditions. Over 11-13 February, 2013, the model was run at Mach numbers between 0.80 and 1.96 at angles of attack at 0 deg, plus or minus 1 deg, plus or minus 2 deg, plus or minus 4 deg, and plus or minus 8 deg. Model roll attitudes at 0 deg, 90 deg, and 180 deg were tested to isolate potential tunnel bias. This paper presents results from the test showing that the proposed holder design significantly reduces the influence of XMIN on measured fluctuating pressure levels.

Herron, A. J.↗
NASA NTRS1986

Real-time open-loop frequency response analysis of flight test data

A technique has been developed to compare the open-loop frequency response of a flight test aircraft real time with linear analysis predictions. The result is direct feedback to the flight control systems engineer on the validity of predictions and adds confidence for proceeding with envelope expansion. Further, gain and phase margins can be tracked for trends in a manner similar to the techniques used by structural dynamics engineers in tracking structural modal damping.

Bosworth, J. T.↗
NASA NTRS1988

Real-time flight test data distribution and display

Enhancements to the real-time processing and display systems of the NASA Western Aeronautical Test Range are described. Display processing has been moved out of the telemetry and radar acquisition processing systems super-minicomputers into user/client interactive graphic workstations. Real-time data is provided to the workstations by way of Ethernet. Future enhancement plans include use of fiber optic cable to replace the Ethernet.

Nesel, Michael C.↗
NASA NTRS2016

Second-Generation Large Civil Tiltrotor 7- by 10-Foot Wind Tunnel Test Data Report

An approximately 6-percent scale model of the NASA Second-Generation Large Civil Tiltrotor (LCTR2) Aircraft was tested in the U.S. Army 7- by 10-Foot Wind Tunnel at NASA Ames Research Center January 4 to April 19, 2012, and September 18 to November 1, 2013. The full model was tested, along with modified versions in order to determine the effects of the wing tip extensions and nacelles; the wing was also tested separately in the various configurations. In both cases, the wing and nacelles used were adopted from the U.S. Army High Efficiency Tilt Rotor (HETR) aircraft, in order to limit the cost of the experiment. The full airframe was tested in high-speed cruise and low-speed hover flight conditions, while the wing was tested only in cruise conditions, with Reynolds numbers ranging from 0 to 1.4 million. In all cases, the external scale system of the wind tunnel was used to collect data. Both models were mounted to the scale using two support struts attached underneath the wing; the full airframe model also used a third strut attached at the tail. The collected data provides insight into the performance of the preliminary design of the LCTR2 and will be used for computational fluid dynamics (CFD) validation and the development of flight dynamics simulation models.

Theodore, Colin R.↗
NASA NTRS1976

Comparison of model and flight test data for an augmentor-wing STOL research aircraft

The major areas of confidence derived from wind tunnel tests performed on the Augmentor-Wing jet-STOL research aircraft were delineated and it was shown that, for the most part, tunnel results compare favorably with flight experience. Since the model differs in some respects from the actual aircraft, precise correlation between tunnel and flight tests results were not expected; in some areas the model tests were known to be non-representative so that a degree of uncertainty remained: these areas of greater uncertainty are identified and again discussed in the light of subsequent flight tests.

Cook, W. L.↗
NASA NTRS2021

Thermal Conductivity Estimation from Transient Test Data with Embedded Thermocouples using Genetic Algorithm Optimization

Inverse heat transfer methodology previously developed to estimate thermal properties of high temperature fibrous insulation from embedded thermocouples was applied to the thermoplastic polymer, polyether-ether-ketone (PEEK). A small experimental setup was utilized to test the PEEK sample between temperatures of 300 K and 525 K at atmospheric pressure. Cylindrical plugs of PEEK with three thermocouples embedded at various depths were incorporated in the test sample. The experimental PEEK thermocouple data were used as the boundary and initial conditions of a one-dimensional numerical thermal model to predict the internal temperatures of the material. The thermal conductivity of PEEK was estimated with the Continuous Genetic Algorithm optimization technique by searching for the coefficients of a functional form of thermal conductivity that minimized the difference between the experimentally measured and model predicted internal temperature values. The thermal testing, one-dimensional numerical thermal model, optimization algorithm, analysis, and results are presented.

Thermal Properties↗
NASA NTRS1979

A procedure obtaining stiffnesses and masses of a structure from vibration modes and substructure static test data

A component mode desynthesis procedure is developed for determining the unknown vibration characteristics of a structural component (i.e., a launch vehicle) given the vibration characteristics of a structural system composed of that component combined with a known one (i.e., a payload). At least one component static test has to be performed. These data are used in conjunction with the system measured frequencies and mode shapes to obtain the vibration characteristics of each component. The flight dynamics of an empty launch vehicle can be determined from measurements made on a vehicle/payload combination in conjunction with a static test on the payload.

Edighoffer, H. H.↗
NASA NTRS2011

End-of-Life Optical Property Predictions of White Conductive Thermal Control Coatings through Analysis of On-Orbit and Ground Based Testing Data

New system requirements pertaining to thermal optical properties and coating electrical properties are commonly specified on non-low earth orbit missions. An increasing number of projects are specifying coatings with a surface resistivity of less than lE-9 ohm/square to mitigate electrostatic charge buildup events over a range of operational temperatures. There are a limited number of coatings that. meet these electrical property requirements while having flight derived optical properties in representative environments. Goddard Space Flight Center Code 546, Contamination and Thermal Coatings Group has recently explored the variety of electrically conductive white coatings available through domestic vendors to evaluate properties to meet project requirements in a geostationary orbit. The lack of significant flight data in representative environments required the careful selection of samples in ground based tests to establish end of life thermal properties. Attention must be given to the origin and pedigree of samples used on past on-orbit experiments to insure that the present formulations for the materials are similar and will react in similar manner.

Hasegawa, Mark↗
NASA NTRS2016

Summary of LaRC 2-inch Erectable Joint Hardware Heritage Test Data

As the National Space Transportation System (STS, also known as the Space Shuttle) went into service during the early 1980's, NASA envisioned many missions of exploration and discovery that could take advantage of the STS capabilities. These missions included: large orbiting space stations, large space science telescopes and large spacecraft for manned missions to the Moon and Mars. The missions required structures that were significantly larger than the payload volume available on the STS. NASA Langley Research Center (LaRC) conducted studies to design and develop the technology needed to assemble the large space structures in orbit. LaRC focused on technology for erectable truss structures, in particular, the joint that connects the truss struts at the truss nodes. When the NASA research in large erectable space structures ended in the early 1990's, a significant amount of structural testing had been performed on the LaRC 2-inch erectable joint that was never published. An extensive set of historical information and data has been reviewed and the joint structural testing results from this historical data are compiled and summarized in this report.

Dorsey, John T.↗
NASA NTRS1997

HARV ANSER Flight Test Data Retrieval and Processing Procedures

Under the NASA High-Alpha Technology Program the High Alpha Research Vehicle (HARV) was used to conduct flight tests of advanced control effectors, advanced control laws, and high-alpha design guidelines for future super-maneuverable fighters. The High-Alpha Research Vehicle is a pre-production F/A-18 airplane modified with a multi-axis thrust-vectoring system for augmented pitch and yaw control power and Actuated Nose Strakes for Enhanced Rolling (ANSER) to augment body-axis yaw control power. Flight testing at the Dryden Flight Research Center (DFRC) began in July 1995 and continued until May 1996. Flight data will be utilized to evaluate control law performance and aircraft dynamics, determine aircraft control and stability derivatives using parameter identification techniques, and validate design guidelines. To accomplish these purposes, essential flight data parameters were retrieved from the DFRC data system and stored on the Dynamics and Control Branch (DCB) computer complex at Langley. This report describes the multi-step task used to retrieve and process this data and documents the results of these tasks. Documentation includes software listings, flight information, maneuver information, time intervals for which data were retrieved, lists of data parameters and definitions, and example data plots.

Yeager, Jessie C.↗
NASA NTRS2016

Simulation and Flight Test Data Collection to Support Phase 1 Detect-and-Avoid MOPS

The UAS Integration into the NAS (UASNAS) project is studying the minimum operational performance standards for unmanned aerial system (UAS) detect-and-avoid (DAA) systems in order to operate in the National Airspace System (NAS). The project is executing a series of fast-time simulation, human-in-the-loop experiments, and flight tests in support of this effort. Armstrong Flight Research Center is hosting a VIP Day in conjunction with the UAS-NAS Project's Flight Test 4 activity, and the Ames Project Engineer (or designate) will be presenting a briefing. This briefing will review the data collection and analysis activities for Flight Test 4 within the Separation assurance-Sense-and-avoid Interoperability (SSI) team.

data analysis↗