Search NASA⌕ Search

SEARCH · Search NASA

Results for “tokamak”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Electron temperature gradient driven transport model for tokamak plasmas

A new model for electron temperature gradient (ETG) modes is developed as a component of the multi-mode anomalous transport module [Rafiq et al., Phys Plasmas 20, 032506 (2013)] to predict a time-dependent electron temperature profile in conventional and low aspect ratio tokamaks. This model is based on two-fluid equations that govern the dynamics of low-frequency short- and long-wavelength electromagnetic toroidal ETG driven drift modes. A low collisionality NSTX discharge is used to scan the plasma parameter dependence on the ETG real frequency, growth rate, and electron thermal diffusivity. Electron thermal transport is discovered in the deep core region where modes are more electromagnetic in nature. Several previously reported gyrokinetic trends are reproduced, including the dependencies of density gradients, magnetic shear, β and gradient of β (β'), collisionality, safety factor, and toroidicity, where β is the ratio of the plasma pressure to the magnetic pressure. Furthermore, the electron heat diffusivity associated with the ETG mode is discovered to be on a scale consistent with the experimental diffusivity determined by power balance analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Resistive wall tearing mode disruptions in DIII-D and ITER tokamaks

Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTMs) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. Here, the nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Gas puff imaging on the TCV tokamak

We present the design and operation of a suite of Gas Puff Imaging (GPI) diagnostic systems installed on the Tokamak à Configuration Variable (TCV) for the study of turbulence in the plasma edge and Scrape-Off-Layer (SOL). These systems provide the unique ability to simultaneously collect poloidal 2D images of plasma dynamics at the outboard midplane, around the X-point, in both the High-Field Side (HFS) and Low-Field Side (LFS) SOL, and in the divertor region. We describe and characterize an innovative control system for deuterium and helium gas injection, which is becoming the default standard for the other gas injections at TCV. Extensive pre-design studies and the different detection systems are presented, including an array of avalanche photodiodes and a high-speed CMOS camera. First results with spatial and time resolutions of up to ≈2 mm and 0.5 µs, respectively, are described, and future upgrades of the GPI diagnostics for TCV are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Modeling of carbon and tungsten transient dust influx in tokamak edge plasma

The paper presents computer simulation studies of burst injection of carbon and tungsten dust particles in DIII-D-like edge plasmas. The injection causes a large transient influx of the low- and high-Z impurities associated with the dust ablation in the plasmas. The dust transport and the effects of the ablated impurities on the edge plasma dynamics in a modern mid-size tokamak geometry are investigated for low- and high-power plasma discharge conditions. The core plasma contamination with dust-ablated impurities and the factors affecting it are evaluated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

ETG turbulence in a tokamak pedestal

This paper explores the fundamental characteristics of electron-temperature-gradient (ETG)-driven turbulence in the tokamak pedestal. The extreme gradients in the pedestal produce linear instabilities and nonlinear turbulence that are distinct from the corresponding ETG phenomenology in the core plasma. The linear system exhibits multiple (greater than ten) unstable eigenmodes at each perpendicular wave vector, representing different toroidal and slab branches of the ETG instability. Proper orthogonal decomposition of the nonlinear fluctuations reveals no clear one-to-one correspondence between the linear and nonlinear modes for most wave vectors. Moreover, nonlinear frequencies deviate strongly from those of the linear instabilities, with spectra peaking at positive frequencies, which is opposite the sign of the ETG instability. The picture that emerges is one in which the linear properties are preserved only in a narrow range of k-space. Outside this range, nonlinear processes produce strong deviations from both the linear frequencies and eigenmode structures. This is interpreted in the context of critical balance, which enforces alignment between the parallel scales and fluctuation frequencies. We also investigate the nonlinear saturation processes. We observe a direct energy cascade from the injection scale to smaller scales in both perpendicular directions. However, in the bi-normal direction, there is also nonlocal inverse energy transfer to larger scales. Neither streamers nor zonal flows dominate the saturation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The fast camera (Fastcam) imaging diagnostic systems on the DIII-D tokamak

Two camera systems are installed on the DIII-D tokamak at the toroidal positions of 90° (90° system) and 225° (225° system), respectively. The cameras have two types of relay optics, namely, a coherent optical fiber bundle and a periscope system. The periscope system provides absolute intensity calibration stability while sacrificing resolution (10 lp/mm), while the fiber system provides high resolution (16 lp/mm) while sacrificing calibration stability. The periscope is available only for the 90° system. The optics of the 225° system were designed for view stability, repeatability, and easy maintenance. The cameras are located inside optimized neutron, x ray and magnetic shielding in order to reduce electronics damage, reboots, and magnetic and neutron interference, increasing the overall system reliability. An automated filter wheel, providing remote filter change, allows for remote wavelength selection. A software suite automates camera acquisition and data storage, allowing for remote operation and reduced operator involvement. System metadata is used to streamline the data analysis workflow, particularly for intensity calibration. Here, the spatial calibration uses multiple observable wall features, resulting in a reconstruction accuracy ≤2 cm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The theory of kinetic effects on resistive wall mode stability in tokamaks

Tokamak fusion plasmas benefit from high pressures but are then susceptible to modes of instability. These magnetohydrodynamic (MHD) modes are macroscopic distortions of the plasma, but certain collective motions of individual particles can provide stabilizing effects opposing them. The presence of a resistive wall slows the mode growth, converting a kink to a resistive wall mode (RWM). A kinetic MHD model includes Maxwell's equations, ideal MHD constraints, and kinetic effects included through the pressure tensor, calculated with the perturbed drift-kinetic distribution function of the particles. The kinetic stabilizing effects on the RWM arise through resonances between the plasma rotation and particle drift motions: precession, bounce, and transit. A match between particle motions and the mode allows efficient transfer of energy that would otherwise drive the growth of the mode, thus damping the growth. The first approach to calculating RWM stability is to write a set of equations for the complex mode frequency in terms of known quantities and then to solve the system. The “energy principle” approach, which has the advantage of clarity in distinguishing the various stabilizing and destabilizing effects, is to change the force balance equation into an equation in terms of changes of kinetic and potential energies, and then to write a dispersion relation for the mode frequency in terms of those quantities. These methods have been used in various benchmarked codes to calculate kinetic effects on RWM stability. Importantly, the theory has illuminated the important roles of plasma rotation, energetic particles, and collisions in RWM stability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

On discriminating tokamak sawtooth crash models via localized density and temperature measurements

The core electron temperature drops rapidly during the sawtooth crash in tokamak plasmas, which causes heat loss and may lead to fast particle losses or even a disruption. Several models have been proposed for the periodic crash, including the Kadomtsev model with magnetic reconnection and the quasi-interchange model with the growth of higher-mode-number pressure-driven instabilities. 3D MHD simulations were performed for these two models with a goal to develop intuition and to predict qualitatively how different types of sawtooth will appear in various diagnostics. The structures of electron density ne and electron temperature Te show a dominant (1, 1) mode for the Kadomtsev case and a dominant (4, 4) mode for the quasi-interchange case. The oscillations of ne and Te have a positive correlation near the inversion layer for both cases, while their frequencies and amplitudes are different depending on the dominant modes. Particularly, for the Kadomtsev case, we find a relation between the amount of flux reconnected during a sawtooth event and ne or Te oscillations. Therefore, we connect recently developed measurement capabilities for ne and Te to the internal sawtooth behavior. We propose that this method of analysis can help in identifying the type of sawtooth in future experiments augmented by simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Dependence of high- Z redeposition on the field-to-surface pitch angle and other sheath parameters in tokamaks

Accurately predicting redeposition is vital for high-Z plasma-facing component (PFC) survivability in magnetic confinement fusion. In this study, we categorize high-Z redeposition into three mechanisms: geometric-driven (prompt), sheath-driven (local), and scrape-off-layer-driven (far) redeposition. To investigate these mechanisms, we employ Monte Carlo transport codes to simulate azimuthally symmetric tungsten source erosion and redeposition in a tokamak. By iteratively analyzing critical parameters, we evaluate redeposition scaling for each mechanism. Specifically, we investigate the impact of magnetic-field-to-PFC pitch angle assumptions on PFC losses into the scrape-off layer. Our findings reveal significant pitch angle sensitivity due to an asymmetric prompt vs local redeposition trade-off. These results enhance our understanding of redeposition phenomena in fusion plasma environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Filamentary velocity scaling validation and spin dynamics in the DIII-D tokamak

Measured filament velocities in the DIII-D tokamak are compared against theoretical scalings, finding that the latter often represents an upper limit on experimental velocity distributions with most filaments possessing lower velocity. Filament spin from internal E × B drift is experimentally demonstrated to alter filament radial velocity. A critical spin velocity, where filament radial velocity peaks, is observed and corresponds to approximately 5 km/s. This transition is corroborated using a less direct measure of filament spin in the form of a temperature ratio. These techniques are combined to find that the critical spin velocity closely aligns with transport times along and across filaments becoming comparable. The normalized filament size distribution is consistent with the most stable size as dictated by Kelvin–Helmholtz and curvature-driven instabilities. Overall, the findings suggest filament stability and spin alter filamentary transport that may threaten the integrity of first walls in fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Early internal detection of magnetic tearing and implications for tokamak magnetohydrodynamic stability

Internal fluctuation measurements with Faraday-effect polarimetry in the DIII-D tokamak reveal the onset of a tearing mode with toroidal mode number n = 3 well before it is detected by the sensing coils external to the plasma. This mode appears before the n = 2, 1 modes and is first detected with internal measurements at a lower value of the ideal-wall kink beta limit than is indicated at the time of first detection by the sensing coils. When the mode is first detected, the linear resistive stability parameter, Δ′, indicates marginal stability and continues to do so until later when the mode amplitude begins increasing linearly with time—together suggesting a neoclassical origin for this mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Calculation of tearing mode stability in an inverse aspect-ratio expanded tokamak plasma equilibrium

The tearing mode stability of an inverse aspect-ratio expanded tokamak plasma equilibrium of general shape is investigated using asymptotic matching techniques. Particular emphasis is placed on the conservation of toroidal electromagnetic angular momentum. The TJ code, which is a specific implementation of the results of the investigation, is described.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Electron cyclotron emission quasi-optical transmission system on the HL-3 tokamak

A new quasi-optical (QO) Electron Cyclotron Emission (ECE) transmission system has been established on the HL-3 tokamak, which includes a focusing QO mirror combination and a long-distance transmission line. This system was developed to meet the requirements for poloidal spatial resolution and the high signal-to-noise ratio needed for magnetohydrodynamic (MHD) instability studies using ECE on the HL-3. The QO mirror combination was installed inside the vacuum chamber for focusing. Laboratory test results, theoretical calculations, and synthetic ECE simulation results indicate that the Gaussian beam can meet the spatial resolution requirements for the accurate measurement of the MHD instability on the q = 1/2/3 surfaces, corresponding to the poloidal mode numbers m = 3/6/9. This includes good diagnostic poloidal spatial resolution for the important 2/1 and 3/2 modes. At the front end of the transmission line, a high-efficiency mode converter was designed to transition the TE 10 mode to the HE 11 mode for input into the transmission line, with an insertion loss of less than 1.5 dB. A 30 m long-distance corrugated oversized waveguide was constructed, with transmission losses ranging from 6 to 10 dB in the 60–120 GHz range. Polarization adjustment results show that the polarization offset and geometric spatial polarization angle change consistently, which can provide a reference for polarization adjustment in other complex structured transmission lines. As a result, the newly established ECE QO transmission system will provide strong support for future physics research involving ECE on the HL-3.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Real-time steerable frequency-stepped Doppler backscattering (DBS) system for local helicon wave electric field measurements on the DIII-D tokamak

A new frequency-stepped Doppler backscattering (DBS) system has been integrated into a real-time steerable electron cyclotron heating launcher system to simultaneously probe local background turbulence (f < 10 MHz) and high-frequency (20–550 MHz) density fluctuations in the DIII-D tokamak. The launcher allows for 2D steering (horizontally and vertically) over wide angular ranges to optimize probe location and wavenumber response. The vertical steering can be optimized during a discharge in real time. The new DBS system employs a programmable frequency synthesizer with adjustable dwell time as a source to launch either O or X-mode polarized millimeter waves. This system can step in real-time over the entire E-band frequency range (60–90 GHz). This combination of capabilities allows for the diagnosis of the complex internal spatial structure of high power (>200 kW) helicon waves (476 MHz) injected from an external antenna during helicon current drive experiments in DIII-D. Broadband density fluctuations around the helicon frequency are observed during real-time scans of measurement location and wavenumber during these experiments. Analysis indicates that these broadband high-frequency fluctuations are a result of backscattering of the DBS millimeter-wave probe beam from plasma turbulence modulated by the helicon wave. It is observed that background turbulence is effectively locally “tagged” with the helicon wave electric field, forming images of the turbulent spectrum in the overall density fluctuation spectrum that appear as high-frequency sidebands of the turbulence. These observations of background turbulence and high-frequency fluctuations open up the possibility of monitoring local helicon wave amplitude by comparing the high-frequency signal amplitude to the simultaneously measured background turbulence. In combination with the real-time measurement location and wavenumber scanning capabilities (offered by real-time frequency-stepping and steering), this allows rapid determination of the spatial distribution of the helicon wave power during steady-state plasma operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Integrated modeling of advanced tokamaks for tearing mode avoidance on DIII-D

Understanding the physics of the onset and evolution of tearing modes (TMs) in tokamak plasmas is crucial for high-performance steady-state operations. The onset condition of (m,n) = (2,1) tearing stability, $Δ′$ > $Δ_c^′$> 0, has been studied in DIII-D steady-state hybrid discharges with accurate equilibrium reconstruction and well-measured plasma profiles. Here, m is the poloidal mode number and n is the toroidal mode number. The onset of n = 1 TMs is carefully identified using the Mirnov array to determine in-phase signals for the onset time and using electron cyclotron emission measurements to trace back from the saturated island width in the experiments for both initial island width and its growth rate. The tearing stability index $Δ′$ at TM onset is calculated in multiple ways, using the modified Rutherford equation and using the PEST-III or resistive DCON magnetohydrodynamic codes, and the results are in reasonable agreement with each other. The calculated $Δ′$ is compared with an analytical formula of the tearing stability threshold $Δ_c^′$ to determine the condition for the mode onset, $Δ′$ > $Δ_c^′$. Finally, the local gradient effect of the plasma current and the pressure profiles on the tearing stability is investigated in terms of the difference between $Δ′$ and $Δ_c^′$ through a series of modeled equilibria with the parametric variations. A database of experimental mode instability onsets is compatible with the simulated regions of instability obtained from the parametric variations.

Linear stability analysis↗
DOE OSTI2024

Erratum: “Initial characterization of electron temperature and density profiles in PEGASUS spherical tokamak discharges driven solely by local helicity injection” [Phys. Plasmas 28, 102504 (2021)]

Here, this article describes errata in 'Initial characterization of electron temperature and density profiles in PEGASUS spherical tokamak discharges driven solely by local helicity injection,' Phys. Plasmas 28, 102504 (2021) that correct reported electron temperature values and their implications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Resistive hose modes in tokamak runaway electron beams II

Resistive hose instabilities of runaway electron (RE) beams immersed in resistive background plasmas are examined with analytic and numerical calculations. The RE beam-plasma equilibria considered are characteristic of the situation observed post-thermal quench in a tokamak disruption. An analytic linear dispersion relation is presented for the case of a uniform RE current density profile with a sharp boundary in cylindrical geometry. Initial value linear calculations for a more general profile in toroidal geometry find that reducing aspect ratio increases the resistive hose mode growth rates with fixed safety factor profile. Nonlinear calculations in cylindrical and toroidal geometry find that the resistive hose instability-driven fluctuations relax the gradient of the current density profile. In toroidal geometry, changes to the magnetic topology are observed as a result of the resistive hose activity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Simulations of plasma current induced by toroidal field ramping down on tokamaks

In tokamak experiments, the BT ramping down can drive off-axis and parallel inductive current. This approach leads to a decrease in q95 and an increase in normalized beta, βN. The off-axis inductive current also broadens the current profile. Typically, the 1.5D transport code is used to simulate the time evolution of the plasma current profile, which is based on the flux-surface-averaged Faraday’s law. The ONETWO code is one of those transport codes. However, this code cannot simulate the situation of the evolving toroidal field BT. This article proposes a new time-dependent model to take into account the BT ramping down situation. A modified formula of flux-surface-averaged Faraday’s law was derived to consider the effect of the BT ramping rate on the current evolution, and it was implemented in the ONETWO code. Then, the modified ONETWO code was used to simulate the BT ramping down experiment on DIII-D. The simulation result of the plasma current evolution with BT ramping down shows a broader current profile with smaller ohmic current induced by the poloidal field, compared to that without BT ramping down.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗