Search NASA⌕ Search

SEARCH · Search NASA

Results for “transition electron microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Two-level systems in nucleated and non-nucleated epitaxial alpha-tantalum films

Building usefully coherent superconducting quantum processors depends on reducing losses in their constituent materials. Tantalum, like niobium, has proven utility as the primary superconducting layer within highly coherent qubits. However, unlike Nb, high temperatures are typically used to stabilize the desirable body-centered-cubic phase, α-Ta, during thin film deposition. It has long been known that a thin Nb layer permits the room-temperature nucleation of α-Ta, but here we observe the epitaxial process and present few-photon microwave loss measurements in Nb-nucleated Ta films. We compare resonators patterned from Ta films grown at high temperature (500 °C) and films nucleated at room temperature, in order to understand the impact of the crystalline order on quantum coherence. In both cases, films grew with Al 2 O 3 (001) ∥ Ta (110), indicating that the epitaxial orientation is independent of temperature and is preserved across the Nb/Ta interface. We use conventional low-power spectroscopy to measure two level system (TLS) loss as well as an electric-field bias technique to measure the effective dipole moments of TLS in the surfaces of resonators. In our measurements, Nb-nucleated Ta resonators had greater loss tangent (1.5 ± 0.1 × 10 -5 ) than non-nucleated (5 ± 1× 10 -6 ) in approximate proportion to defect densities as characterized by x-ray diffraction (0.27° vs 0.18° [110] reflection width) and electron microscopy (30 vs 70 nm domain size). Furthermore, the dependence of the loss tangent on domain size indicates that the development of more ordered Ta films is likely to lead to improvements in qubit coherence times. Moreover, low-temperature α-Ta epitaxy may enable the growth of microstate-free heterostructures, which would not withstand high temperature processing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Challenges to magnetic doping of thin films of the Dirac semimetal Cd 3 As 2

Magnetic doping of topological quantum materials provides an attractive route for studying the effects of time-reversal symmetry breaking. Thus motivated, we explore the introduction of the transition metal Mn into thin films of the Dirac semimetal Cd 3 A s2 during growth by molecular beam epitaxy. Scanning transmission electron microscopy measurements show the formation of a Mn-rich phase at the top surface of Mn-doped Cd 3 A s2 thin films grown using both uniform doping and delta doping. This suggests that Mn acts as a surfactant during epitaxial growth of Cd 3 A s2 , resulting in phase separation. Magnetometry measurements of such samples indicate a ferromagnetic phase with out-of-plane magnetic anisotropy. Electrical magneto-transport measurements of these films as a function of temperature, magnetic field, and chemical potential reveal a lower carrier density and higher electron mobility compared with pristine Cd 3 A s2 films grown under similar conditions. This suggests that the surfactant effect might also serve to remove impurities from the bulk of the film. Further, we observe robust quantum transport (Shubnikov-de Haas oscillations and an incipient integer quantum Hall effect) in very thin (7 nm) Cd 3 A s2 films despite being in direct contact with a structurally disordered surface ferromagnetic overlayer.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Toward nonthermal control of excited quantum materials: framework and investigations by ultrafast electron scattering and imaging

Quantum material systems upon applying ultrashort laser pulses provide a rich platform to access excited material phases and their transformations that are not entirely like their equilibrium counterparts. The addressability and potential controls of metastable or long-trapped out-of-equilibrium phases have motivated interests both for the purposes of understanding the nonequilibrium physics and advancing the quantum technologies. Thus far, the dynamical spectroscopic probes eminently focus on microscopic electronic and phonon responses. For characterizing the long-range dynamics, such as order parameter fields and fluctuation effects, the ultrafast scattering probes offer direct sensitivity. Bridging the connections between the microscopic dynamics and macroscopic responses is central toward establishing the nonequilibrium physics behind the light-induced phases. Here, we present a path toward such understanding by cross-examining the structure factors associated with different dynamical states obtained from ultrafast electron scattering, imaging, and modeling. We give the basic theoretical framework on describing the non-equilibrium scattering problems and briefly describe how such framework relates to the out-of-equilibrium phenomena. We give effective models outlining the emergences of nonthermal critical points, hidden phases, and non-equilibrium relaxational responses from vacuum-suspended rare-earth tritellurides, tantalum disulfides thin films, and vanadium dioxide nanocrystalline materials upon light excitations.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

PRODUCTION OF GLASS-TO-METAL SEALS USING ADDITIVE MANUFACTURING TECHNIQUES

Glass-to-metal (GtM) seals are hermetic barriers between glass and metal components, often used in the electronic and vacuum industries. Creating the seals traditionally requires heating all the components to the glass melting temperature, where the glass will flow and bond to the metal. Due to the manufacturing constraints of the individual components and sealing conditions there are geometric and material restrictions. Additive manufacturing techniques were used to make GtM seals to reduce these restrictions. Hermetic, single pin seals were produced using printed metal shells, by selective laser melting (SLM), and digital light processing (DLP) printed glass preforms. Glass preforms were printed with photosensitive resin mixed with a silicate sealing glass powder in a 1:2 weight ratio. Thermal analysis, TGA/DSC, and screening experiments were used to determine an organic removal schedule. Video techniques determined a sintering schedule by producing a densification curve at different isothermal holds which were fit with a viscous sintering model. Single pin seals were also produced use a laser assisted manufacturing (LAM) process as an alternative to the conventional furnace sealing process. A Nd:YAG laser was focused on a solid glass preform, heating the glass to form the glass-metal bond. The sealing glass was doped with a transition metal oxide, Fe2O3 or CuO, to increase absorption of the laser wavelength. The interface of hermetic LAM seals were analyzed using electron microscopy, compared to conventional prepared seals, finding a reduction of interfacial morphologies.

Read, Aaron Reece↗
DOE OSTI2019

AC Magnetic Susceptibility of Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18} Substituted by Nd{sup 3+} and Ca{sup 2+} Ions

Effect of Nd{sup 3+} and Ca{sup 2+} ion substitutions in Y{sub 3}Ba{sub 5}Cu{sub 8}O{sub 18} (Y-358) was studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), electrical resistivity, and ac magnetic susceptibility measurements. Superconducting samples of type Y{sub 3 − x}Nd{sub x}Ba{sub 5 − y}Ca{sub y}Cu{sub 8}O{sub 18} (with 0 ≤ x, y ≤ 0.4) were synthesized by the standard solid-state reaction technique. XRD patterns revealed that all the samples were mainly composed of Y-358 phase with orthorhombic structure. SEM micrographs showed that Nd{sup 3+} and Ca{sup 2+} ion substitutions had the ability to alter the grain morphology of Y-358 to irregular randomly oriented grains with smaller average grain sizes. The temperature-dependent electrical resistivity curves indicated that the superconducting transition temperature T{sub c} was decreased from 96.51 to 87.41 K as the substitution contents were increased from 0 to 0.4. Detailed AC magnetic susceptibility measurements were done using a quantum design physical property measurement system (PPMS) at different dc fields (B = 0.5–20 kG) and frequency of 1 kHz. A comparison between electrical resistivity and AC magnetic susceptibility data was performed. It was found that T{sub cs} obtained from AC magnetic susceptibility were much lower than those obtained from the resistivity measurements, for all studied samples. This was discussed in terms of filamentary paths that could produce sharp pronounced drops in diamagnetism. Generally, the depression in T{sub c} was attributed to the decrease in relative volume fraction of Y-358 or due to trapping of mobile holes or other mechanism connected with oxygen vacancy disorder. Werthamer–Helfand–Hohenberg (WHH) theory was employed to study the temperature dependence of the upper critical magnetic field B{sub c2}(T) for the samples. The relative importance of both orbital and paramagnetic effects in the suppression of superconductivity was described with the aid of Maki parameter (κ{sub M}). The estimated values of the upper critical magnetic field at 0 K, B{sub c2}(0), were found to decrease from 37.3 to 13.5 T as Nd{sup 3+} and Ca{sup 2+} contents were increased from 0 to 0.4. This decrement was attributed to the weak electron–phonon coupling and to the orbital as well as spin pair breaking mechanisms. Furthermore, Ginzburg–Landau coherence length ξ{sub GL} of Y{sub 3 − x}Nd{sub x}Ba{sub 5 − y}Ca{sub y}Cu{sub 8}O{sub 18} was found to increase with the increase of the Nd{sup 3+} and Ca{sup 2+} contents. Therefore, Nd{sup 3+} and Ca{sup 2+} ions play an important role in the pair-breaking mechanism and in suppressing superconductivity of the Y-358 phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

A novel design of transitional layer structure between reduced activation ferritic martensitic steels and tungsten for plasma facing materials

Plasma-facing components (PFCs) are among the most critical gaps for fusion energy to establish technical and economic feasibility. Tungsten as a first wall/blanket material in PFCs requires to be integrating with reduced activation ferritic martensitic (RAFM) steels as a structural component. Currently, major drawbacks are the requirement of brazing, the formation of a brittle interface, and a large difference between the coefficients of thermal expansion of tungsten and steel. Here, a novel transitional multilayer structure was designed and investigated to join tungsten and RAFM steels using three interlayers. The composition of each interlayer was selected based on computational thermodynamics and diffusion kinetics to ensure a body-centered cubic (bcc) single-phase structure and prevent the formation of a brittle intermetallic phase region in the temperature range of 600–1150 °C. Although the transitional layer structure was designed for additive manufacturing, spark plasma sintering (SPS) as proof of concept was used to bond the individual layers. Interfaces were investigated using scanning and transmission electron microscopy methods but no layered intermetallic phase was observed. Nanoindentation maps across the interface suggest major hardness differences at the interface between tungsten and the vanadium interlayer, as well as the interface between RAFM steel and the FeCrAl interlayer.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Order-disorder phase transition driven by interlayer sliding in lead iodides

A variety of phase transitions have been found in two-dimensional layered materials, but some of their atomic-scale mechanisms are hard to clearly understand. Here, we report the discovery of a phase transition whose mechanism is identified as interlayer sliding in lead iodides, a layered material widely used to synthesize lead halide perovskites. The low-temperature crystal structure of lead iodides is found not 2H polytype as known before, but non-centrosymmetric 4H polytype. This undergoes the order-disorder phase transition characterized by the abrupt spectral broadening of valence bands, taken by angle-resolved photoemission, at the critical temperature of 120 K. It is accompanied by drastic changes in simultaneously taken photocurrent and photoluminescence. The transmission electron microscopy is used to reveal that lead iodide layers stacked in the form of 4H polytype at low temperatures irregularly slide over each other above 120 K, which can be explained by the low energy barrier of only 10.6 meV/atom estimated by first principles calculations. Our findings suggest that interlayer sliding is a key mechanism of the phase transitions in layered materials, which can significantly affect optoelectronic and optical characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Calibrating cryogenic temperature of TEM specimens using EELS

Cryogenic Scanning/Transmission Electron Microscopy has been established as a leading method to image sensitive biological samples and is now becoming a powerful tool to understand materials' behavior at low temperatures. However, achieving precise local temperature calibration at low temperatures remains a challenge, which is especially crucial for studying phase transitions and emergent physical properties in quantum materials. In this study, we employ electron energy loss spectroscopy (EELS) to measure local cryogenic specimen temperatures. Here we use the temperature-dependent characteristics of aluminum's bulk plasmon peak in EEL spectra, which shifts due to changes in electron density caused by thermal expansion and contraction. We successfully demonstrate the versatility of this method by calibrating different liquid nitrogen cooling holders in various microscopes, regardless of whether a monochromated or non-monochromated electron beam is used. Temperature discrepancies between the actual temperature and the setpoint temperatures are identified across a range from room temperature to 100 K. This work demonstrates the importance of temperature calibrations at intermediate temperatures and presents a straightforward, robust method for calibrating local temperatures of cryogenically-cooled specimens in electron microscopes.

36 MATERIALS SCIENCE↗
DOE OSTI2019

In Situ TEM Study of the Amorphous-to-Crystalline Transition during Dielectric Breakdown in TiO 2 Film

Dielectric breakdown of oxides is a main limiting factor for improvement of the performance of electronic devices. Present understanding suggests that defects produced by intense voltage accumulate in the oxide to form a percolation path connecting the two electrodes and trigger the dielectric breakdown. However, reports on directly visualizing the process at nanoscale are very limited. Here, we apply in situ transmission electron microscopy to characterize the structural and compositional changes of amorphous TiO 2 under extreme electric field (~100 kV/mm) in a Si/TiO 2 /W system. Upon applying voltage pulses, the amorphous TiO 2 gradually transformed to crystalline sub-stoichiometric rutile TiO 2-x and the Magnéli phase Ti 3 O 5 . The transitions started fromat the anode/oxide interface under both field polarities. Preferred growth orientation Epitaxial growth of rutile TiO 2-x with respect toon the Si substrate was observed when Si was the anode, while oxidation and melting of the W probe occurred when W was the anode. We associate the TiO 2 crystallization process with the electrochemical reduction of TiO 2 , polarity-dependent oxygen migration, and Joule heating. The experimental results are supported by our phase-field modeling. These findings provide direct details of the defect formation process during dielectric breakdown in amorphous oxides and will help the design of electronic devices with higher efficiency and reliability.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Visualizing Crystallization Dynamics and Transformation Pathways of Disordered Rocksalt Oxides During Thermally Activated Sol–Gel Synthesis

Sol–gel synthesis is a wet-chemical processing route for fabricating functional materials with control over composition and microstructure at relatively low temperatures compared to conventional solid-state synthesis. While sol–gel process initiates with intermixed molecular precursors, the early-stage nucleation pathways are insufficiently understood. Here, in this study, the chemical and structural transformation of ion disordered rocksalt (DRX) Li 1.2 Mn 0.4 Ti 0.4 O 2 (LMTO), a promising cathode material for lithium batteries, is studied by multiscale characterizations. In situ heating transmission electron microscopy (TEM) using a liquid cell visualizes and identifies crystallization pathways at the nanoscale. While some regions follow a classical multi-step transition through thermodynamically stable intermediates, others exhibit a kinetic shortcut via a localized amorphous matrix to directly form the DRX structure. Macroscale Fourier transform infrared spectroscopy corroborates the findings and reveals that transition metal ions are more strongly incorporated into the acetate-coordinated network than lithium. Although in situ heating TEM captures diverse local transformation pathways, in situ synchrotron X-ray diffraction indicates that the macroscopic transformation proceeds predominantly through spinel LMTO and lithium titanates toward DRX-LMTO. The findings uncover the spatiotemporal chemical and structural transformations in sol–gel derived DRX-LMTO materials, and call for fine-tuning of such sol–gel chemistries to manipulate the crystallization pathways and achieve target material homogeneity more efficiently.

cathode material↗
DOE OSTI2023

Degradation in Ni-Rich LiNi 1– x – y Mn x Co y O 2 /Graphite Batteries: Impact of Charge Voltage and Ni Content

Ni-rich LiNi 1– x–y Mn x CoyO 2 (NMC) materials are attractive as cathodes for Li-ion batteries due to their high energy density and low Co content. However, these materials may display poor electrochemical reversibility relating to structural and interfacial instabilities. The influence of Ni content and level of delithiation during charge on degradation mechanisms and relevance to electrochemical cycling behavior are probed for LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode materials in a full cell configuration under two upper voltage limits (4.1 and 4.3 V). The combined use of dQ/dV analysis of electrochemical voltage profiles, operando XRD, and postcycling scanning electron microscopy (SEM) measurements indicates that a major contributor to capacity fade is the large anisotropic volume change from an H2 $\leftrightarrows$ H3 phase transition and associated mechanical degradation particularly for NMC811. Notably, transition metal dissolution and deposition on the negative electrode are found to correlate with the structural changes occurring in the cathode under high voltage charge. X-ray photoelectron spectroscopy (XPS) analyses of the cycled cathodes reveal a more organic-rich cathode–electrolyte interphase (CEI) when cycling to 4.3 V with lower relative amounts of LiF. Surface reconstruction is not a significant factor under these cycling conditions as determined by soft X-ray absorption spectroscopy (sXAS) analysis. The results emphasize the opportunity to match the electrochemical test parameters with the specific NMC active material to mitigate degradation and extend cycle life.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Emergence of Topologically Nontrivial Spin-Polarized States in a Segmented Linear Chain

The synthesis of new materials with novel or useful properties is one of the most important drivers in the fields of condensed matter physics and materials science. Discoveries of this kind are especially significant when they point to promising future basic research and applications. Van der Waals bonded materials comprised of lower-dimensional building blocks have been shown to exhibit emergent properties when isolated in an atomically thin form. Here, we report the discovery of a transition metal chalcogenide in a heretofore unknown segmented linear chain form, where basic building blocks each consisting of two hafnium atoms and nine tellurium atoms (Hf 2 Te 9 ) are van der Waals bonded end-to-end. First-principle calculations based on density functional theory reveal striking crystal-symmetry-related features in the electronic structure of the segmented chain, including giant spin splitting and nontrivial topological phases of selected energy band states. In this work, atomic-resolution scanning transmission electron microscopy reveals single segmented Hf 2 Te 9 chains isolated within the hollow cores of carbon nanotubes, with a structure consistent with theoretical predictions. Van der Waals-bonded segmented linear chain transition metal chalcogenide materials could open up new opportunities in low-dimensional, gate-tunable, magnetic and topological crystalline systems.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Continuous-flow synthesis of thermochromic M-phase VO2 particles via rapid one-step hydrothermal reaction – effect of mixers

VO2 particles are promising materials for thermochromic smart windows that reduce building energy loss. Continuous-flow hydrothermal processes showcase advantages for synthesizing VO2 particles compared with traditional batch reaction systems. Mixers play a crucial role in particle fabrication in continuous-flow systems. In this study, a Center T-Mixer and a Collision Cross-Mixer are developed and implemented in a hot water fluidized suspension reaction (HWFSR) system. The influence of the resident time on the particle phase and size was evaluated, and properties of particles derived from systems equipped with differing mixers were compared. The resulting particles were characterized using techniques of X-ray powder diffraction (XRD) analysis, scanning electron microscopy (SEM), and differential scanning calorimetry (DSC). When compared with the Center T-Mixer, results indicate that the Collision Cross-Mixer has better control regarding the morphology and size distribution of resulting particles while improving the transition temperatures of the as-synthesized materials. HWFSR systems containing novel mixer designs are capable of producing pure M-phase VO2 particles in a single step contrary to the current reactor design that use a second postheat treatment step, and they are capable of synthesizing many other nanoparticle species, especially those requiring high temperature and pressure reaction conditions.

continuous-flow process↗
DOE OSTI2025

Aqueous Self‐Assembly of Cylindrical and Tapered Bottlebrush Block Copolymers

The self‐assembly of amphiphilic bottlebrush block copolymers (BCPs), featuring backbones densely grafted with two types of side chains, is less well understood compared to linear BCPs. In particular, the solution self‐assembly of tapered bottlebrush BCPs—cone‐shaped BCPs with hydrophilic or hydrophobic tips—remains unexplored. This study investigates eight tapered and four cylindrical bottlebrush BCPs with varied ratios of hydrophobic polystyrene (PS) and hydrophilic poly(acrylic acid) (PAA) side chains, synthesized via sequential addition of macromonomers using ring‐opening metathesis polymerization (SAM‐ROMP). Self‐assembled nanostructures formed in water were analyzed using cryogenic transmission electron microscopy, small‐angle neutron scattering, and dynamic light scattering. Most BCPs generated multiple nanostructures with surface protrusions, including spherical micelles, cylindrical micelles, and vesicles, alongside transitional forms like ellipsoids and semi‐vesicles. Coarse‐grained molecular dynamics simulations supported the experimental findings, which revealed two distinct self‐assembly pathways. The first involved micelle fusion, producing elliptical and cylindrical aggregates, sometimes forming Y‐junctions. The second pathway featured micelle maturation into semivesicles, which developed into vesicles or large compound vesicles. This work provides the first experimental evidence of vesicle formation via semivesicles in bottlebrush BCPs and demonstrates the significant influence of cone directionality on self‐assembly behavior in these cone‐shaped polymeric amphiphiles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Smectic and nematic phase modulations and transitions under electron beam in Tb 2 Cu 0.83 Pd 0.17 O 4

Understanding the structural origin of the functionality in cuprates has attracted tremendous attention over several decades. In particular, probing distortions in the Cu- O bonding is of great importance for exploring the coupling between the charge and the lattice, a key mechanism for superconductivity and other functionality in correlated materials. Here we study a superlattice modulation in the Tb 2 Cu 0.83 Pd 0.17 O 4 “214” material, which possesses no superconductivity itself but has the parent structure of the R 2 CuO 4 (R = a rare earth element) superconducting cuprate group. Using transmission electron microscopy (TEM), we find that this superlattice modulation is formed by Cu ion displacements in a direction perpendicular to the Cu-O planes. The superlattice modulation undergoes a reversible electronic smectic-nematic phase transition under electron-beam illumination. With the help of in situ TEM results, our findings imply that the superlattice modulation in this material arises from spatially modulated charge ordering at the Cu sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Complex-Concentrated Anion Doping Enables Ultra-Stable Lattice Oxygen and Structural Integrity in Lithium-Rich Layered Oxide Cathodes

Lithium- and manganese-rich layered oxides (LMR) stand out as next-generation lithium-ion cathode chemistries, which harness both transition-metal and lattice-oxygen redox processes to deliver exceptional capacity and energy density. However, their full potential is hindered by intrinsic oxygen instability and structural degradation, resulting in pronounced voltage fade and capacity decay. Here, we present a complex-concentrated anion-doping paradigm in which multiple anions, F, Br, and S, are incorporated into the oxygen sublattice to enhance oxygen-redox and structural stability. X-ray absorption spectroscopy and aberration-corrected scanning transmission electron microscopy confirm ultra-stable local oxygen coordination environments during long-term cycling, with detrimental phase transformations and oxygen-loss-induced cavitation dramatically inhibited. Notably, we show that the characteristic LiTM6 transition metal (TM) honeycomb ordering is preserved even after electrochemical cycling. Concurrently, this strategy yields an unprecedented volume change of only 0.63% upon charging to 4.8 V vs. Li+/Li, achieving the first zero-strain LMR cathode. The resulting LMR cathode delivers ultralow voltage fade (1 mV per cycle during the first 100 cycles and becomes negligible in subsequent cycles) and outstanding energy retention (93% after 200 cycles) in a pouch cell configuration. Our complex-concentrated anion-doping concept establishes a broadly applicable strategy for resolving chemo-mechanical failure mechanisms in ceramic intercalation electrodes for next-generation energy storage.

Li-ion batteries↗
DOE OSTI2022

Thermal Hysteresis and Ordering Behavior of Magnetic Skyrmion Lattices

The physics of phase transitions in two-dimensional (2D) systems underpins research in diverse fields including statistical mechanics, nanomagnetism, and soft condensed matter. However, many aspects of 2D phase transitions are still not well understood, including the effects of interparticle potential, polydispersity, and particle shape. Magnetic skyrmions are chiral spin-structure quasi-particles that form two-dimensional lattices. Here, in this study, we show, by real-space imaging using in situ cryo-Lorentz transmission electron microscopy coupled with machine learning image analysis, the ordering behavior of Néel skyrmion lattices in van der Waals Fe 3 GeTe 2 . We demonstrate a distinct change in the skyrmion size distribution during field-cooling, which leads to a loss of lattice order and an evolution of the skyrmion liquid phase. Remarkably, the lattice order is restored during field heating and demonstrates a thermal hysteresis. This behavior is explained by the skyrmion energy landscape and demonstrates the potential to control the lattice order in 2D phase transitions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Effect of sucrose on foaming and melting behavior of a low-activity waste melter feed

Reductants, such as sucrose, are added to nuclear waste melter feeds containing high fractions of nitrates and nitrites to reduce excessive foaming during feed-to-glass conversion and to decrease sulfate segregation and increase technetium retention. The sucrose effect on foaming and melting reactions during the conversion was examined using the feed volume expansion, thermogravimetric analysis, evolved gas analysis, X-ray diffraction, and scanning electron microscopy with energy dispersive X-ray spectrometry. Different sucrose additions were used to vary the carbon to nitrogen (C/N) ratio in the melter feed. As C/N ratio increased, the extent of foaming decreased and N2/NO ratio increased in the gas phase evolved. Significant foam suppression, rapid gas release at approximately 250°C, and reduction of transition metal oxides were observed at C/N > 1.1.

Appel, Connor J.↗