Search NASA⌕ Search

SEARCH · Search NASA

Results for “wrapping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Verification of large beam-type space structures

The verification approach here proposed for large, beam-type space structures consists of a first part, which removes the gravity effect on the substructure tested and identifies its on-orbit dynamic characteristics, on the basis of ground test measurements, and a second part which develops an adequate scaling law that extrapolates the dynamic characteristics of the prototype structure by using results from the substructure. These approaches are presently demonstrated for the cases of a wrap-rib antenna's feed support structure and a candidate Space Shuttle flight experiment.

Shih, C.-F.↗
NASA NTRS1986

Development of a reusable, flight-weight cryogenic foam insulation system

Attention is given to a light weight foam insulation system applicable to reusable cryogenic propellant tankage for hypersonic aircraft and space launch vehicles. The insulation system consists of nominally sized blocks of a high temperature-resistant polymethacrylimide foam that is wrapped with a vapor-impermeable membrane of Kapton-aluminum-Kapton laminate, which is adhesively bonded to the outer propellant tank wall. Test results are presented which indicate that this insulation system is capable of enduring a Mach 5 service environment without structural cracking, deterioration, or loss of performance.

Mcauliffe, P. S.↗
NASA NTRS1986

Molecular clouds in the Carina arm

Results from the first large-scale survey in the CO(J = 1 to 0) line of the Vela-Carina-Centaurus region of the Southern Milky Way are reported. The observations, made with the Columbia University 1.2 m millimeter-wave telescope at Cerro Tololo, were spaced every beamwidth (0.125 deg) in the range 270 deg is less than or = l is less than or = 300 deg and -1 deg less than or = b less then or = 1 deg, with latitude extensions to cover all Carina arm emission beyond absolute b = 1 deg. In a concurrent survey made with the same telescope, every half-degree in latitude and longitude was sampled. Both surveys had a spectral coverage of 330 km/s with a resolution of 1.3 km/s. The Carina arm is the dominant feature in the data. Its abrupt tangent at l is approx. = 280 deg and characteristic loop in the l,v diagram are unmistakable evidence for CO spiral structure. When the emission is integrated over velocity and latitude, the height of the step seen in the tangent direction suggests that the arm-interarm contrast is at least 13:1. Comparison of the CO and H I data shows close agreement between these two species in a segment of the arm lying outside the solar circle. The distribution of the molecular layer about the galactic plane in the outer Galaxy is determined. Between R = 10.5 and 12.5 kpc, the average CO midplane dips from z = -48 to -167 pc below the b = 0 deg plane, following a similar well-known warping of the H I layer. In the same range of radii the half-thickness of the CO layer increases from 112 to 182 pc. Between l = 270 deg and 300 deg, 27 molecular clouds are identified and cataloged along with heliocentric distances and masses. An additional 16 clouds beyond 300 deg are cataloged from an adjoining CO survey made with the same telescope. The average mass for the Carina arm clouds is 1.4x 10(6)M (solar), and the average intercloud spacing along the arm is 700 pc. Comparison of the distribution of the Carina arm clouds with that of similarly massive molecular clouds in the first and second quadrants strongly suggests that the Carina and Sagittarius arms form a single spiral arm approx. 40 kpc long wrapping two-thirds of the way around the Galaxy.

Grabelsky, D. A.↗
NASA NTRS1986

Numerical Solution of the Incompressible Navier-Stokes Equations in Three-dimensional Generalized Curvilinear Coordinates

Numerically solving the incompressible Navier-Stokes equations is known to be time consuming and expensive. Testing of the INS3D computers code, which solves these equations with the use of the pseudocompressibility method, shows this method to be an efficient way to obtain the steady state solution. The effects of the waves introduced by the pseudocompressibility method are analyzed and criteria are set and tested for the choice of the pseudocompressibility parameter which governs the artificial sound speed. The code is tested using laminar flow over a two dimensional backward-facing step, and laminar flow over a two dimensional circular cylinder. The results of the computations over the backward-facing step are in excellent agreement with experimental results. The transient solution of the flow over the cylinder impulsively started from rest is in good agreement with experimental results. However, the computed frequency of periodic shedding of vortices behind the cylinder is not in agreement with the experimental value. For a three dimensional test case, computations were conducted for a cylinder end wall junction. The saddle point separation and horseshoe vortex system appear in the computed field. The solution also shows secondary vortex filaments which wrap around the cylinder and spiral up in the wake.

Rogers, S. E.↗
NASA NTRS1987

Verification of large beam-type space structures

The verification approach of large beam type space structures is verified. The proposed verification approach consists of two parts. The first part is to remove the gravity effect on the tested substructure and to identify the on-orbit dynamic characteristics of the substructure by using the measurements of the ground test. A scaling law is also established to define the critical length of the structure which can be tested in 1-g field without incurring a buckling problem. The second part is to develop an adequate scaling law to extrapolate the dynamic characteristics of the prototype structure by using results from the substructure. The verification approaches are demonstrated on two typical structural configurations, the feed support structure of a wrap-rip antenna and a candidate shuttle flight experiment. The results indicate that it is practical to verify the on-orbit dynamic characteristics of these structures by using the proposed approach.

Shih, Choon-Foo↗
NASA NTRS1987

Finite element models of wire rope for vibration analysis

The usefulness of wire rope in shock and vibration isolation is briefly reviewed and its modeling for the purpose of vibration analysis is addressed. A model of a nominally straight segment of wire rope is described in which the rope structure is represented by a maiden, or central, strand of wire with one (or more) strand(s) wrapped around it in a helix (helices). The individual strands are modeled using finite elements and MSC NASTRAN. Small linear segments of each wire are modeled mathematically by dividing them lengthwise into triangular prisms representing each prism by a solid NASTRAN element. To model pretensioning and allow for extraction of internal force information from the NASTRAN model, the wound strands are connected to the maiden strand and each other using spring (scalar elastic) elements. Mode shapes for a length of wire rope with one and fixed to a moving base and the other attached to a point mass, are presented. The use of the NASTRAN derived mode shapes to approximate internal normal forces in equations of motion for vibration analyses is considered.

Cochran, J. E., Jr.↗
NASA NTRS1987

Antenna Technology Shuttle Experiment (ATSE)

Numerous space applications of the future will require mesh deployable antennas of 15 m in diameter or greater for frequencies up to 20 GHz. These applications include mobile communications satellites, orbiting very long baseline interferometry (VLBI) astrophysics missions, and Earth remote sensing missions. A Lockheed wrap rip antennas was used as the test article. The experiments covered a broad range of structural, control, and RF discipline objectives, which is fulfilled in total, would greatly reduce the risk of employing these antenna systems in future space applications. It was concluded that a flight experiment of a relatively large mesh deployable reflector is achievable with no major technological or cost drivers. The test articles and the instrumentation are all within the state of the art and in most cases rely on proven flight hardware. Every effort was made to design the experiments for low cost.

Freeland, R. E.↗
NASA NTRS1985

Digital control system for space structure dampers

A digital controller was developed using an SKD-51 System Design Kit, which incorporates an 8031 microcontroller. The necessary interfaces were installed in the wire wrap area of the SKD-51 and a pulse width modulator was developed to drive the coil of the actuator. Also, control equations were developed, using floating-point arithmetic. The design of the digital control system is emphasized, and it is shown that, provided certain rules are followed, an adequate design can be achieved. It is recommended that the so-called w-plane design method be used, and that the time elapsed before output of the up-dated coil-force signal be kept as small as possible. However, the cycle time for the controller should be watched carefully, because very small values for this time can lead to digital noise.

Haviland, J. K.↗
NASA NTRS1986

Advanced photovoltaic solar array program - A preliminary assessment

Two solar array designs developed for the Advanced Photovoltaic Solar Array program are described. The goal of the program is to develop solar arrays with higher mass specific power and power density and good robustness. The specific design requirements are: a beginning-of-life value of 130 W/kg, and end-of-life goals of 105 W/kg and 110 W/sq m. The two array-wing designs consisted of a single blanket. The differences in the blanket material (25 micron-thick Kapton versus 50 micron-thick carbon-loaded Kapton), solar cells (100 micron-thick wrap around versus 50 micron-thick 2 x 4 cm planar contact cells), and performance objectives (proposed industry requirements versus mission objectives) of the two designs are examined.

Scott-Monck, J.↗
NASA NTRS1986

Direct measurement of skin friction with a new instrument

The design and performance of a small belt-type skin-friction gage to measure wall shear-stress coefficients in wind-tunnel testing are described, summarizing the report of Vakili and Wu (1982). The sensor employs a flexible belt of variable surface characteristics; this belt, wrapped tightly around two cylinders mounted on frictionless flexures, is equipped with strain gages to estimate the deflection of the belt by the flow. An alternative approach uses IR illumination, optical fibers, and a photosensitive transistor, permitting direct measurement of the belt deflection. Drawings, diagrams, and graphs of sample data are provided.

Vakili, A. D.↗
NASA NTRS1986

Bubbles and braided jets in galaxies with compact radio nuclei

Narrow-band H-alpha CCD images showing ionized gas in organized kiloparsec-scale structures in three galaxies with low-level active nuclei are presented. The edge-on spiral NGC 3079 contains an apparent loop structure which corresponds to previously reported nonthermal radio emission along the minor axis. The optical emission probably results from interaction between the ejected plasma and the ISM in the disk and halo. The S0 galaxy NGC 3998 exhibits an S-shaped structure centered on the nucleus, with no other evidence for spiral structure. In the spiral galaxy NGC 4258, the presence of continuum-free emission-line arms which coincide with the nonthermal radio arms is confirmed. The morphology of the arms suggests the presence of two double-sided jets which braid or wrap around one another and which bifurcate on both sides. It is concluded that the optical and radio emission in NGC 3079 and in NGC 4258 are related, and it is suggested that both are powered by a plasma which flows from the active nucleus and dissipates kinetic energy in the surrounding ISM.

Ford, Holland C.↗
NASA NTRS1987

Self-similar potential in the near wake

The plasma potential is measured near the edge of an electrically floating obstacle placed in a steady-state, supersonic, unmagnetized, neutral plasma flow. Equipotential contours show the sheath of the upstream side of the obstacle wrapping around the edge of the obstacle and fanning out into the near wake. Both fluid theory and the data find the near-wake plasma potential to be self-similar when ionization, charge exchange, and magnetic field can be neglected. The theory also finds that fluid velocity is self-similar, the near wake is nonneutral, and plasma density is not self-similar. Strong electric fields are found near the obstacle and equipotential contours are found to conform to all boundaries.

Diebold, D.↗
NASA NTRS1987

Detecting forest structure and biomass with C-band multipolarization radar - Physical model and field tests

The ability of C-band radar (4.75 GHz) to discriminate features of forest structure, including biomass, is tested using a truck-mounted scatterometer for field tests on a 1.5-3.0 m pygmy forest of cypress (Cupressus pygmaea) and pine (Pinus contorta ssp, Bolanderi) near Mendocino, CA. In all, 31 structural variables of the forest are quantified at seven sites. Also measured was the backscatter from a life-sized physical model of the pygmy forest, composed of nine wooden trees with 'leafy branches' of sponge-wrapped dowels. This model enabled independent testing of the effects of stem, branch, and leafy branch biomass, branch angle, and moisture content on radar backscatter. Field results suggested that surface area of leaves played a greater role in leaf scattering properties than leaf biomass per se. Tree leaf area index was strongly correlated with vertically polarized power backscatter (r = 0.94; P less than 0.01). Field results suggested that the scattering role of leaf water is enhanced as leaf surface area per unit leaf mass increases; i.e., as the moist scattering surfaces become more dispersed. Fog condensate caused a measurable rise in forest backscatter, both from surface and internal rises in water content. Tree branch mass per unit area was highly correlated with cross-polarized backscatter in the field (r = 0.93; P less than 0.01), a result also seen in the physical model.

Westman, Walter E.↗
NASA NTRS1987

Magnetic reorientation and spontaneous formation of tangential discontinuities in deformed magnetic fields

This paper provides an explicit illustration of the formation of tangential discontinuities (current sheets) in a force-free magnetic field whose footpoints have been subjected to bounded continuous displacement and shuffling so that the lines of force are wound about each other in complex but continuous patterns. The discontinuities appear spontaneously because of the reorientation of the field under the enhanced pressure where two regions of different field topology are pressed together by the general winding and wrapping.

Parker, E. N.↗
NASA NTRS1988

Fast Detection Of Breaks In Ducts

Breaks in optical fibers reveal failures in duct walls. Group of optical fibers wrapped around duct carries light beams from lasers to photodiodes. Break in duct breaks fiber bonded to it, interrupting path of light between laser and photodetector. Interruption used to command shutdown of engine or other system to minimize damage.

Smith, Matthew A.↗
NASA NTRS1988

Chromic acid anodizing of aluminum foil

The success of the Space Station graphite/epoxy truss structure depends on its ability to endure long-term exposure to the LEO environment, primarily the effects of atomic oxygen and the temperture cycling resulting from the 94 minute orbit. This report describes the development and evaluation of chromic acid anodized (CAA) aluminum foil as protective coatings for these composite tubes. Included are: development of solar absorptance and thermal emittance properties required of Al foil and development of CAA parameters to achieve these optical properties; developing techniques to CAA 25 ft lengths of Al foil; developing bonding processes for wrapping the Al foil to graphite/epoxy tubes; and atomic oxygen testing of the CAA Al foil. Two specifications were developed and are included in the report: Chromic Acid Anodizing of Aluminum Foil Process Specification and Bonding of Anodized Aluminum Foil to Graphite/Epoxy Tubes. Results show that CAA Al foil provides and excellent protective and thermal control coating for the Space Station truss structure.

Dursch, H.↗
NASA NTRS1988

Technologies for antenna shape and vibration control

This paper describes the application of advanced control methods and techniques to the second- and third-generation mobile satellite (MSAT) configurations having wrap-rib offset feed construction. The technologies are generically applicable to other designs such as hoop-column and other elastically deformable non-rigid structures. The focus of the discussion is on reflector shape determination and control, dynamics identification, and pointing jitter suppression.

Mettler, Edward↗
NASA NTRS1988

Techniques for assessment of flexible space structure control performance

Several multivariable concepts are presently applied to both the open-loop and closed-loop analysis of a wrap-rib antenna space structure. After evaluating the alternative placements of sensors and actuators by means of controllability, observability, and transmission-zero concepts, the linear quadratic gaussian/loop transfer recovery method is used to synthesize a control law for suppression of the transient vibrations that are typically encountered during maneuvers. The integration of these techniques and associated computer programs into a larger spacecraft design system is also discussed.

Rowell, Lawrence F.↗