SEARCH · Search NASA

Results for “AFTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1989

RSRM nozzle fixed housing cooldown test

Flight 5 aft segments with nozzles were exposed to -17 F temperatures while awaiting shipment to KSC in February, 1989. No records were found which show that any previous nozzles were exposed to air temperatures as low as those seen by the Flight 5 nozzles. Thermal analysis shows that the temperature of the fixed housing, and forward and aft exit cone components dropped as low as -10 F. Structural analysis of the nozzles at these low temperatures show the forward and aft exit cone adhesive bonds to have a positive margin of safety, based on a 2.0 safety factor. These analyses show the normal and shear stresses in the fixed housing bond as low values. However, the hoop and meridinal stresses were predicted to be in the 4000 psi range; the failure stress allowable of EA913NA adhesive at -7 F. If the bonds did break in directions perpendicular to the surfaces, called bond crazing, no normal bond strength would be lost. Testing was conducted in two phases, showing that no degradation to the adhesive bonds occurred while the Flight 5 nozzles were subjected to subzero temperatures. The results of these tests are documented. Phase 1 testing cooled a full-scale RSRM insulated fixed housing to -13 F, with extensive bondline inspections. Phase 2 testing cooled the witness panel adhesive tensile buttions to -13 F, with failure strengths recorded before, during, and after the cooldown.

Bolieau, D. J.↗

NASA NTRS1989

SRB thermal environments

The objective was to utilize and expand the Solid Rocket Booster (SRB) orbital flight test data base for better predictions of future flight environments. There were five tasks associated with this effort: analyze the internal aft skirt wind tunnel data and incorporate it into a data base for generating design and preflight reeentry thermal environments; generate reentry design thermal environments for the SRB steel case with the nozzle extension off; generate reentry design thermal environments for the SRB Filament Wound Case with the nozzle extension off; develop an engineering tool to analyze the 3-D flowfield around the SRB aft skirt during reentry for the purpose of obtaining the frequency and severity of the belching gas intrusion internal to the aft skirt; and perform SRM transient joint flow analysis for subscale and full scale motor firing as well as determine the effects of debonds of the insulation on the fill time and heating within the field joint insulation. In addition, this work was extended to provide support for the 51L Shuttle SRB failure analysis.

Crain, W. K.↗

NASA NTRS1990

Flight motor set 360L002 (STS-27R). Volume 5: Nozzle component

A review of the performance and post-flight condition of the STS-27 Redesigned Solid Rocket Motor (RSRM) nozzles is presented. Thermal/Structural instrumentation data is reviewed, and applicable Discrepancy Reports (DRs) and Process Departures (PDs) are presented. The Nozzle Component Program Team (NCPT) performance evaluation and the Redesign Program Review Board (RPRB) assessment is included. The STS-27 nozzle assemblies were flown on the RSRM Second Flight (Space Shuttle Atlantis) on 2 December 1988. The nozzles were a partially submerged convergent and/or divergent movable design with an aft pivot point flexible bearing. The nozzle assemblies incorporated the following features: RSRM forward exit cone with snubber assembly, RSRM fixed housing, Structural backup Outer Boot Ring (OBR), RSRM cowl ring, RSRM nose inlet assembly, RSRM throat assembly, RSRM aft exit cone assembly with Linear-Shaped Charge (LSC), RTV backfill in Joints 1, 3, and 4, Use of EA913 NA adhesive in place of EA913 adhesive, Redesigned nozzle plug, and Carbon Cloth Phenolic (CCP) with 750 ppm sodium content. The CCP material usage for the STS-27 forward nozzle and aft exit cone assemblies is shown.

Meyer, S. A.↗

NASA NTRS1990

Flight motor set 36OH005 (STS-28R). Volume 5: (Nozzle component)

A review of the performance and post flight condition of the STS-28 redesigned solid rocket motor (RSRM) nozzles is presented in this document. Applicable discrepancy reports (DR's) and process departures (PD's) are presented in section 5.0. The nozzle component program team (NCPT) performance evaluation and the redesign program review board (RPRB) assessment is included in section 6.0. The STS-28 nozzle assemblies were flown on the RSRM fifth flight (Space Shuttle Columbia). The nozzles were a partially submerged convergent/divergent movable design with an aft pivot point flexible bearing. The nozzle assemblies incorporated the following features: (1) RSRM forward exit cone with snubber assembly; (2) RSRM fixed housing; (3) structural backup outer boot ring (OBR); (4) RSRM cowl ring; (5) RSRM nose inlet assembly; (6) RSRM throat assembly; (7) RSRM forward nose and aft inlet ring; (8) RSRM aft exit cone assembly with linear-shaped charge (LSC); (9) RTV backfill in joints 1, 3, and 4; (10) use of EA913 NA adhesive in place of EA913; (11) redesigned nozzle plug; and (12) carbon cloth phenolic (CCP) with 750 ppm sodium content. The RSRM fifth flight test objectives are as follows: (1) verify that flexible bearing seals operate within the specified temperature range; (2) verify that flexible bearing maintained a positive gas seal between its internal components; (3) inspect flexible bearing for damage due to water impact; (4) verify performance of the nozzle liner; (5) verify that nozzle parts are reusable; (6) verify through flight demonstration and a postflight inspection that the flexible bearing is reusable; (7) verify by inspection the remaining nozzle ablative thicknesses; and (8) verify the nozzle performance margins of safety.

Smith, Dan M., Jr.↗

NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

A scale model of a counterrotating propeller with forward-swept blades in the forward rotor and aft-swept blades in the aft rotor (designated F39/A31) has been tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel. This paper presents aeroacoustic results at a takeoff/approach condition of Mach 0.20. Laser Doppler Velocimeter results taken in a plane between the two rotors are also included to quantify the interaction flow field. The intention of the forward-swept design is to reduce the magnitude of the forward rotor tip vortex and/or wakes which impinge on the aft rotor, thus lowering the interaction tone levels.

Woodward, Richard P.↗

NASA NTRS1993

Effect of forebody tangential slot blowing on flow about a full aircraft geometry

The effect of forebody tangential slot blowing on the flowfield about an F/A-18 aircraft is investigated numerically using solutions of the Navier-Stokes equations. Computed solutions are obtained for a full aircraft geometry, including the fuselage, wing with deflected leading-edge flap, empennage, and a faired-over engine inlet. The computational slot geometry corresponds to that used in full-scale wind tunnel tests. Solutions are computed using flight test conditions and jet mass flow ratios equivalent to wind tunnel test conditions. The effect of slot location is analyzed by computing two non-time-accurate solutions with a 16 in. slot located 3 in. and 11 in. aft of the nose of the aircraft. These computations resolve the trends observed in the full-scale wind tunnel test data. The flow aft of the leading edge extension (LEX) vortex burst is unsteady. A time-accurate solution is obtained to investigate the flow characteristics aft of the vortex burst, including the effect of blowing on tail buffet.

Gee, Ken↗

NASA NTRS1993

Computation of the Fluid and Optical Fields About the Stratospheric Observatory for Infrared Astronomy (SOFIA) and the Coupling of Fluids, Dynamics, and Control Laws on Parallel Computers

The June 1992 to May 1993 grant NCC-2-677 provided for the continued demonstration of Computational Fluid Dynamics (CFD) as applied to the Stratospheric Observatory for Infrared Astronomy (SOFIA). While earlier grant years allowed validation of CFD through comparison against experiments, this year a new design proposal was evaluated. The new configuration would place the cavity aft of the wing, as opposed to the earlier baseline which was located immediately aft of the cockpit. This aft cavity placement allows for simplified structural and aircraft modification requirements, thus lowering the program cost of this national astronomy resource. Three appendices concerning this subject are presented.

Atwood, Christopher A.↗

NASA NTRS1991

SRB thermal curtain design support

The objective of the program during this time period was to evaluate candidate materials that could be used to design an improved Solid Rocket Motor (SRM) Aft Skirt Thermal Curtain (ASTC). The ASTC is a flexible, high temperature, cloth and insulation composite that is used to protect the hardware located inside the aft skirt of the shuttle solid rocket booster. The current ASTC consists of nine layers of insulating materials and is 2.58 inches thick. The ASTC is made up of twenty four segments. The segments are hand sewn together during installation on the aft skirt. The weight of the current ASTC is approximated at about six hundred pounds. This weight does not include the weight of the mounting hardware and ties required to install the twenty four ASTC segments (which is significant). The current effort entailed measuring the thermophysical properties of six candidate materials (quartz, S glass, and Kevlar woven into nominal 0.25 inch thick layers by angle interlock and polar-weave) and then using these properties in a computer program to predict the thermal performance of various curtain configurations subjected to an SRM heat flux.

Dixon, Carl A.↗

NASA NTRS1994

Design and fabrication of forward-swept counterrotation blade configuration for wind tunnel testing

Work performed by GE Aircraft on advanced counterrotation blade configuration concepts for high speed turboprop system is described. Primary emphasis was placed on theoretically and experimentally evaluating the aerodynamic, aeromechanical, and acoustic performance of GE-defined counterrotating blade concepts. Several blade design concepts were considered. Feasibility studies were conducted to evaluate a forward-swept versus an aft-swept blade application and how the given blade design would affect interaction between rotors. Two blade designs were initially selected. Both designs involved in-depth aerodynamic, aeromechanical, mechanical, and acoustic analyses followed by the fabrication of forward-swept, forward rotor blade sets to be wind tunnel tested with an aft-swept, aft rotor blade set. A third blade set was later produced from a NASA design that was based on wind tunnel test results from the first two blade sets. This blade set had a stiffer outer ply material added to the original blade design, in order to reach the design point operating line. Detailed analyses, feasibility studies, and fabrication procedures for all blade sets are presented.

Nichols, G. H.↗

NASA NTRS1994

Forward sweep, low noise rotor blade

A forward-swept, low-noise rotor blade includes an inboard section, an aft-swept section, and a forward-swept outboard section. The rotor blade reduces the noise of rotorcraft, including both standard helicopters and advanced systems such as tiltrotors. The primary noise reduction feature is the forward sweep of the planform over a large portion of the outer blade radius. The rotor blade also includes an aft-swept section. The purpose of the aft-swept region is to provide a partial balance to pitching moments produced by the outboard forward-swept portion of the blade. The noise source showing maximum noise reduction is blade-vortex interaction (BVI) noise. Also reduced are thickness, noise, high speed impulsive noise, cabin vibration, and loading noise.

Brooks, Thomas F.↗

NASA NTRS1996

Subsonic Aerodynamic Characteristics of a Circular Body Earth-to-Orbit Vehicle

A test of a generic reusable earth-to-orbit transport was conducted in the 7- by 10-Foot high-speed tunnel at the Langley Research Center at Mach number 0.3. The model had a body with a circular cross section and a thick clipped delta wing as the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center vertical fin, wingtip fins, and a nose-mounted vertical fin. The configuration was longitudinally stable about the estimated center-of-gravity position of 0.72 body length and had sufficient pitch-control authority for stable trim over a wide range of angle of attack, regardless of fin arrangement. The maximum trimmed lift/drag ratio for the aft center-fin configuration was less than 5, whereas the other configurations had values of above 6. The aft center-fin configuration was directionally stable for all angles of attack tested. The wingtip and nose fins were not intended to produce directional stability but to be active controllers for artificial stabilization. Small rolling-moment values resulted from yaw control of the nose fin. Large adverse rolling-moment increments resulted from tip-fin controller deflection above 13 deg angle of attack. Flow visualization indicated that the adverse rolling-moment increments were probably caused by the influence of the deflected tip-fin controller on wing flow separation.

Lepsch, Roger A., Jr.↗

NASA NTRS1994

Forebody Tangential Slot Blowing on an Aircraft Geometry

The effect of forebody tangential slot blowing on the flowfield about an F/A-18 aircraft is investigated numerically using solutions of the Navier-Stokes equations. Computed solutions are obtained for an aircraft geometry which includes the fuselage, a wing with deflected leading-edge flap, empennage, and a faired-over engine inlet. The computational slot geometry corresponds to that used in full-scale wind-tunnel tests. Solutions are computed using flight test conditions and jet mass flow ratios equivalent to wind-tunnel test conditions. The effect of slot location is analyzed by computing two nontime-accurate solutions with a 16-in. slot located 3 in. and 11 in. aft of the nose of the aircraft. These computations resolve the trends observed in the full-scale wind-tunnel test data. The flow aft of the leading-edge extension vortex burst is unsteady. A time-accurate solution is obtained to investigate the flow characteristics aft of the vortex burst, including the effect of blowing on tail buffet.

Gee, Ken↗

NASA NTRS1995

SRM Internal Flow Tests and Computational Fluid Dynamic Analysis: Titan, ASRM, and Subscale Motor Analyses - Volume 3

A computational fluid dynamics (CFD) analysis has been performed on the aft slot region of the Titan 4 Solid Rocket Motor Upgrade (SRMU). This analysis was performed in conjunction with MSFC structural modeling of the propellant grain to determine if the flow field induced stresses would adversely alter the propellant geometry to the extent of causing motor failure. The results of the coupled CFD/stress analysis have shown that there is a continual increase of flow field resistance at the aft slot due to the aft segment propellant grain being progressively moved radially toward the centerline of the motor port. This 'bootstrapping' effect between grain radial movement and internal flow resistance is conducive to causing a rapid motor failure.

Source record↗

NASA NTRS1998

Nonlinear Analysis of the Space Shuttle Superlightweight LO2 Tank: Behavior Under 3g End-of-Flight Loads - Part 2

Results of linear bifurcation and nonlinear analyses of the Space Shuttle super lightweight (SLWT) external liquid-oxygen (LO2) tank are presented for an important end-of-flight loading condition. These results illustrate an important type of response mode for thin-walled shells, that are subjected to combined mechanical and thermal loads, that may be encountered in the design of other liquid-fuel launch vehicles. Linear bifurcation analyses are presented that predict several nearly equal eigenvalues that correspond to local buckling modes in the aft dome of the LO2 tank. In contrast, the nonlinear response phenomenon is shown to consist of a short-wavelength bending deformation in the aft elliptical dome of the LO2 tank that grows in amplitude in a stable manner with increasing load. Imperfection sensitivity analyses are presented that show that the presence of several nearly equal eigenvalues does not lead to a premature general instability mode for the aft dome. For the linear bifurcation and nonlinear analyses, the results show that accurate predictions of the response of the shell generally require a large-scale, high fidelity finite-element model. Results are also presented that show that the SLWT LO2 tank can support loads in excess of approximately 1.9 times the values of the operational loads considered.

Nemeth, Michael P.↗

NASA NTRS1998

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

The Space Shuttle is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the Space Shuttle and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the blast container for two specific reasons: (1) To eliminate lead for environmental concerns, and (2) To reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hang-ups. This upgrade will replace the lead liner with a unique open cell aluminum foam material, that has commercial and military uses. The aluminum foam used as an energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: (A) Lead handling/exposure and possible contamination, along with hazardous waste disposal, will be eliminated; (B) Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam instead of lead; (C) The new aluminum liner is designed to catch all shrapnel from frangible nuts, thus virtually eliminating chance of debris exiting the HDP and causing potential damage to the vehicle; and (D) Using the lighter aluminum liner instead of lead, allows for easier assembly and disassembly of blast container elements, which also improves safety, operator handling, and the efficiency of operations.

Balles, Donald↗

NASA NTRS1999

Some Acoustic Results from the Pratt and Whitney Advanced Ducted Propulsor: Fan 1

Noise measurements were obtained for the Advanced Ducted Propulsor (ADP) - Fan 1, with and without nacelle acoustic treatment. The fan was tested with no acoustic treatment (hard wall) and with acoustic treatment installed in three configurations in the nacelle (mid, mid plus aft, fully treated). The hard wall results showed that the radiated noise from the fan came primarily from the aft end of the nacelle. At takeoff and higher speeds, the noise measured at the inlet angles was also found to be dominated by noise from the aft end. Significant amounts of attenuation were observed with acoustic treatment installed and comparison with predictions showed the treatment gave more attenuation than predicted. Effective Perceived Noise Levels were determined for a large hypothetical 4 engine airplane. These levels showed that the installed acoustic treatment provided as much as 5 EPNdB of noise reduction. A traverse with a probe having three microphones, one above the other, showed azimuthal variations in the noise that need to be further investigated.

Dittmar, James H.↗

NASA NTRS1999

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

The Space Shuttle is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the Space Shuttle and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the blast container for two specific reasons: (1) To eliminate lead for environmental concerns, and (2) To reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hang-ups. This upgrade will replace the lead liner with a unique open cell aluminum foam material, that has commercial and military uses. The aluminum foam used as an energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: (1) Lead handling / exposure and possible contamination, along with hazardous waste disposal, will be eliminated; (2) Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam instead of lead; (3) The new aluminum liner is designed to catch all shrapnel from frangible nuts, thus virtually eliminating chance of debris exiting the HDP and causing potential damage to the vehicle; (4) Using the lighter aluminum liner instead of lead, allows for easier assembly and disassembly of blast container elements, which also improves safety, operator handling, and the efficiency of operations.

Balles, Donald↗

NASA NTRS1998

Development of Lead Free Energy Absorber for Space Shuttle Blast Container

The Space Shuttle vehicle (SSV) is connected to the mobile launch platform (MLP) by four aft skirt hold down studs on each solid rocket booster (SRB). Prior to lift-off, the frangible nuts inside the aft skirt blast containers (BC) are severed into two nut halves by two pyrotechnic booster cartridges. This action releases the SSV and allows the hold down studs to eject through the aft skirt bore and then down into the MLP. USBI has been tasked to upgrade the BC for two specific reasons; 1. to eliminate lead for environmental concerns, and 2. to reduce the chance of nut recontact with the holddown stud. Nut recontact with the stud has been identified as a likely contributor to stud hangups. This upgrade will replace the lead liner with an aluminum foam material. The aluminum foam used as a energy absorber is a proven design in many other aerospace/defense applications. Additional benefits of using the open cell, energy absorbent aluminum foam in place of the solid lead liner are: A. Lead handling/ exposure, and possible contamination, along with hazardous waste disposal will be eliminated; B. Approximately 200 lbs. weight savings will be contributed to each Space Shuttle flight by using aluminum foam over lead; C. The new aluminum liner is designed to catch all shrapnel from frangible nuts thus virtually eliminating chance of foreign object debris (FOD) exiting the HDP, and causing potential damage to the vehicle; D. Potential of using the lighter aluminum liner over lead, allows for easier assembly and disassembly of blast container elements, also allowing for improvements in safety, operator handling, and efficiency of operations. Six BC firing tests will be required to determine if the new liner material will perform in a way to decrease the chance of stud hangups and enhance the ability of the BC to retain blast debris. Testing will be performed at the Kennedy Space Center (KSC) facility known as the Launch Equipment Test Facility (LETF), and will simulate the SRB hold- down post, with actual BC hardware and pyrotechnics assembled, and then test fired. Initial testing was performed in 1997 using a frangible nut in a static drop test over lead and aluminum foam sheet materials. The aluminum foam showed a dramatic improvement of energy absorption over the lead liner material. Proof-of-Principle testing at the KSC-LETF commenced in May, 1998, and is expected to be completed by June, 1998.

Ingram, T.↗