Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRFOILS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Lift enhancement of an airfoil using a Gurney flap and vortex generators

The results of a low-speed wind tunnel test are presented for a single-element airfoil incorporating two lift-enhancing devices, namely a Gurney flap and vortex generators. The former consists of a small plate, on the order of one to two percent of the airfoil chord in height, located at the trailing edge perpendicular to the pressure side of the airfoil. The later consist of commercially-available, wishbone-shaped vortex generators. The test was conducted in the NASA Ames 7- by 10-foot Wind Tunnel with a full-span NACA 4412 airfoil. Measurements of surface pressure distributions and wake profiles were made to determine the lift, drag, and pitching-moment coefficients for the various airfoil configurations. The results indicate that the addition of a Gurney flap increased the maximum lift coefficient from 1.49 up to 1.96.

Storms, Bruce L.↗
NASA NTRS1993

Transition effects on compressible dynamic stall of transiently pitching airfoils

Experimental results and analysis of the effects of boundary layer tripping on dynamic stall of a transiently pitching airfoil are presented. At low Mach numbers, the tripped airfoil exhibits qualitative similarity with the behavior of the untripped airfoil. However, the local supersonic flow at Mach numbers greater than 0.3 is significantly modified by the trip leading to vastly different shock/boundary layer interactions, dynamic stall onset and vortex formation angles. The formation of the laminar separation bubble is found to have a favorable influence in delaying dynamic stall on the untripped airfoil flow. In both Mach number regimes, the tripped flow actually stalls at slightly lower angles of attack. Further experimentation with three trips on an oscillating airfoil showed that the dynamic stall process is very sensitive to the state of the turbulence in the boundary layer. This sensitivity points to a need for finer turbulence modeling techniques for use in dynamic stall computations.

Wilder, M. C.↗
NASA NTRS1993

Unsteady aerodynamic behavior of an airfoil with and without a slat

Unsteady flow behavior and load characteristics of a 2D VR-7 airfoil with and without a leading-edge slat were studied in the water tunnel of the Aeroflightdynamics Directorate, NASA Ames Research Center. Both airfoils were oscillated sinusoidally between 5 and 25 deg at Re = 200,000 to obtain the unsteady lift, drag, and pitching moment data. A fluorescent dye was released from an orifice located at the leading edge of the airfoil for the purpose of visualizing the boundary layer and wake flow. The flowfield and load predictions of an incompressible Navier-Stokes code based on a velocity-vorticity formulation were compared with the test data. The test and predictions both confirm that the slatted VR-7 airfoil delays both static and dynamic stall as compared to the VR-7 airfoil alone.

Tung, Chee↗
NASA NTRS1928

Preliminary Investigation on Boundary Layer Control by Means of Suction and Pressure with the U.S.A. 27 Airfoil

The tests described in this report constitute a preliminary investigation of airfoil boundary layer control, as carried out in the atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory, from February to August, 1927. Tests were made on a U.S.A. 27 airfoil section with various slot shapes and combinations, and at various amounts of pressure or suction on the slots. The lift of airfoils can be increased by removing or by accelerating the boundary layer. Removing the boundary layer by suction is more economical than to accelerate it by jet action. Gauze-covered suction slots apparently give the best results. When not in operation, all suction slots tested had a detrimental effect upon the aerodynamic characteristics of the airfoil which was not apparent with the backward-opening pressure slots. Thick, blunt-nose airfoils would seem to give best results with boundary layer control.

Reid, E G↗
NASA NTRS1931

The effect of small variations in profile of airfoils

This report deals with the effect of small variations in ordinates specified by different laboratories for the airfoil section. This study was made in connection with a more general investigation of the effect of small irregularities of the airfoil surface on the aerodynamic characteristics of an airfoil. These tests show that small changes in airfoil contours, resulting from variations in the specified ordinates, have a sufficiently large effect upon the airfoil characteristics to justify the taking of great care in the specification of ordinates for the construction of models.

Ward, Kenneth E↗
NASA NTRS1932

Tests of N.A.C.A. airfoils in the variable-density wind tunnel Series 24

This note is the fifth of a series covering an investigation of a number of related airfoils. It presents the results obtained from tests of a group of six low-cambered airfoils in the variable-density wind tunnel. The mean camber lines are identical for the six airfoils and are of such a form that the maximum mean camber is 2 per cent of the chord and is at a position 0.4 of the chord behind the loading edge. The airfoils differ in thickness only, the maximum-thickness/chord ratios being 0.06, 0.09, 0.12, 0.15, 0.18, and 0.21. The results have been presented in the form of both infinite and finite aspect-ratio characteristics. The values of C(sub L) max/C(sub d) degrees min for this group of airfoils are among the highest thus far obtained, the minimum profile drags being approximately equal to those for the symmetrical series of corresponding thickness, while the maximum lift coefficients are considerably higher.

Jacobs, Eastman N↗
NASA NTRS1932

Characteristics of two sharp-nosed airfoils having reduced spinning tendencies

According to Mr. L.D. Bell, of the Consolidated Aircraft Corporation, certain undesirable spinning characteristics of a commercial airplane were eliminated by the addition of a filler to the forward part of the wing to give it a sharp leading edge. To ascertain what aerodynamic effects result from such a change of section, two airfoils having sharp leading edges were tested in the variable-density wind tunnel. Both sections were derived by modifying the Gott. 398. The tests, which were made at a large value of the Reynolds Number, were carried to very large angles of attack to provide data for application to flight at angles of attack well beyond the stall. The characteristics of the sharp-nosed airfoils are compared with those of the normal Gott. 398 airfoil. Both of the sharp-nosed airfoils, which differ in the angle between the upper and lower surfaces at the leading edge, have about the same characteristics. As compared with the normal airfoil, the maximum lift is reduced by approximately 26 per cent, but the objectionable rapidly decreasing lift with angle of attack beyond the stall is eliminated; the profile drag of the section is slightly reduced in the range of the lift coefficient between 0.2 and 0.85, but at higher and lower lift coefficients the drag is increased.

Jacobs, Eastman N↗
NASA NTRS1938

Wind-tunnel of three lateral-control devices in combination with a full-span slotted flap on an NACA 23012 airfoil

A large-chord NACA 23012 airfoil was tested. The airfoil extended completely across the test section, and two-dimensional flow was approximated. The model was fitted with a full-span slotted flap having a chord 25.66 percent of the airfoil chord. The ailerons investigated extended over the entire span and each had a chord 10 percent of the airfoil chord. The types of ailerons tested were: retractable ailerons, slot-lip ailerons using the lip of the slot for ailerons, and plain ailerons on the trailing edge of the slotted flap. The data are presented in the form of curves of section lift, drag, and pitching-moment coefficients for the airfoil with flap deflected but with ailerons neutral, and of rolling-moment, yawing-moment, and hinge-moment coefficients calculated for a rectangular wing of aspect ratio 6 with a semi-span aileron and a full-span flap. For the ailerons investigated the data indicate that, from considerations of rolling and yawing moments produced and of stick forces desired, the retractable aileron is the most satisfactory means of lateral control for use with a full-span slotted flap.

Wenzinger, Carl J↗
NASA NTRS1954

Airfoil section characteristics at high angles of attack

Information from the literature and from recent investigations is used herein to summarize briefly the effects of airfoil section parameters and flow variables on the aerodynamic characteristics of two-dimensional symmetrical airfoils at high angles of attack. The results presented indicate that airfoil thickness ratio, Reynolds number, Mach number, and surface roughness can all have an important effect on the maximum lift coefficient. The effect of surface roughness seems to be particularly important. Not only can surface roughness cause large decreases in maximum lift coefficient, but also the magnitudes of the effects of Reynolds number, Mach number, and airfoil thickness ratio are much reduced by surface roughness. Beyond the stall, changes in section thickness ratio appear to have little effect on the aerodynamic characteristics of airfoil sections. An investigation of one section through an angle-of-attack range of from 0° to 360° shows that the drag coefficient reaches a value of 2 at an angle of attack of 90°.

Laurence K Loftin, Jr↗
NASA NTRS1925

Aerodynamic Characteristics of Airfoils at High Speeds

This report deals with an experimental investigation of the aerodynamical characteristics of airfoils at high speeds. Lift, drag, and center of pressure measurements were made on six airfoils of the type used by the air service in propeller design, at speeds ranging from 550 to 1,000 feet per second. The results show a definite limit to the speed at which airfoils may efficiently be used to produce lift, the lift coefficient decreasing and the drag coefficient increasing as the speed approaches the speed of sound. The change in lift coefficient is large for thick airfoil sections (camber ratio 0.14 to 0.20) and for high angles of attack. The change is not marked for thin sections (camber ratio 0.10) at low angles of attack, for the speed range employed. At high speeds the center of pressure moves back toward the trailing edge of the airfoil as the speed increases. The results indicate that the use of tip speeds approaching the speed of sound for propellers of customary design involves a serious loss in efficiency.

Briggs, L J↗
NASA NTRS1931

Large-scale aerodynamic characteristics of airfoils as tested in the variable density wind tunnel

In order to give the large-scale characteristics of a variety of airfoils in a form which will be of maximum value, both for airplane design and for the study of airfoil characteristics, a collection has been made of the results of airfoil tests made at full-scale values of the reynolds number in the variable density wind tunnel of the National Advisory Committee for Aeronautics. They have been corrected for tunnel wall interference and are presented not only in the conventional form but also in a form which facilitates the comparison of airfoils and from which corrections may be easily made to any aspect ratio. An example showing the method of correcting the results to a desired aspect ratio has been given for the convenience of designers. In addition, the data have been analyzed with a view to finding the variation of the aerodynamic characteristics of airfoils with their thickness and camber.

Jacobs, Eastman N↗
NASA NTRS1931

Airfoil Pressure Distribution Investigation in the Variable Density Wind Tunnel

Report presents the results of wind tunnel tests of pressure distribution measurements over one section each of six airfoils. Pressure distribution diagrams, as well as the integrated characteristics of the airfoils, are given for both a high and a low dynamic scale or, Reynolds number VL/V, for comparison with flight and other wind-tunnel tests, respectively. It is concluded that the scale effect is very important only at angles of attack near the burble. The distribution of pressure over an airfoil having a Joukowski section is compared with the theoretically derived distribution. A further study of the distribution of pressure over all of the airfoils resulted in the development of an approximate method of predicting the pressure distribution along the chord of any normal airfoil for all attitudes within the working range if the distribution at one attitude is known.

Jacobs, Eastman N↗
NASA NTRS1932

Wind-Tunnel Tests on Airfoil Boundary Layer Control Using a Backward-Opening Slot

This report presents the results of an investigation to determine the effect of boundary layer control on the lift and drag of an airfoil. Boundary layer control was accomplished by means of a backward-opening slot in the upper surface of the hollow airfoil. Air was caused to flow through this slot by a pressure which was maintained inside the airfoil by a blower. Various slot locations, slot openings, and wing pressures were used. The tests were conducted in the 5-foot atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory. Under the test conditions, the maximum lift coefficient was increased about 96 per cent for one slot arrangement, and the minimum drag coefficient was decreased about 27 per cent for another, both being compared with the results obtained with the unslotted airfoil. It is believed from this investigation that the above effects may be increased by the use of larger slot openings, better slot locations, multiple slots, improved airfoil profiles, and trailing edge flaps.

Bamber, Millard J↗
NASA NTRS1932

The aerodynamic characteristics of eight very thick airfoils from tests in the variable density wind tunnel

Report presents the results of wind tunnel tests on a group of eight very thick airfoils having sections of the same thickness as those used near the roots of tapered airfoils. The tests were made to study certain discontinuities in the characteristic curves that have been obtained from previous tests of these airfoils, and to compare the characteristics of the different sections at values of the Reynolds number comparable with those attained in flight. The discontinuities were found to disappear as the Reynolds number was increased. The results obtained from the large-scale airfoil, a symmetrical airfoil having a thickness ratio of 21 per cent, has the best general characteristics.

Jacobs, Eastman N↗
NASA NTRS1937

Airfoil Section Characteristics as Affected by Variations of the Reynolds Number

Report presents the results of an investigation of a systematically chosen representative group of related airfoils conducted in the NACA variable-density wind tunnel over a wide range of Reynolds number extending well into the flight range. The tests were made to provide information from which the variations of airfoil section characteristics with changes in the Reynolds number could be inferred and methods of allowing for these variations in practice could be determined. This work is one phase of an extensive and general airfoil investigation being conducted in the variable-density tunnel and extends the previously published researches concerning airfoil characteristics as affected by variations in airfoil profile determined at a single value of the Reynolds number.

Jacobs, Eastman N↗
NASA NTRS1939

The Compressibility Burble and the Effect of Compressibility on Pressures and Forces Acting on a Airfoil

Simultaneous air-flow photographs and pressure-distribution measurements were made of the NACA 4412 airfoil at high speeds to determine the physical nature of the compressibility burble. The tests were conducted in the NACA 24-inch high-speed wind tunnel. The flow photographs were obtained by the Schlieren method and the pressures were simultaneously measured for 54 stations in the 5-inch-chord airfoil by means of a multiple-tube manometer. Following the general program, a few measurements of total-pressure loss in the wake of the airfoil at high speeds were made to illustrate the magnitude of the losses involved and the extent of the disturbed region; and, finally, in order to relate this work to earlier force-test data, a force test of a 5-inch-chord NACA 4412 airfoil was made. The results show the general nature of the phenomenon known as the compressibility burble. The source of the increased drag is shown to be a compression shock that occurs on the airfoil as its speed approaches the speed of sound. Finally, it is indicated that considerable experimentation is needed in order to understand the phenomenon completely.

Stack, John↗
NASA NTRS1939

Airfoil section data obtained in the NACA variable-density tunnel as affected by support interference and other corrections

The results of an investigation of the effect of support interference on airfoil drag data obtained in the variable-density tunnel are presented. As a result of the support interference, previously published airfoil data from the variable-density tunnel have shown too large drag coefficients and too large a rate of increase of drag coefficients and too large a rate increase of drag coefficients with airfoil thickness. The practical effect of the corrections on the choice of the optimum section is briefly considered and corrected data for a selected list of airfoils are presented as a convenience to the designer. Methods of correcting published data for other airfoils are presented.

Jacobs, Eastman N↗
NASA NTRS1941

Tests of the NACA 0025 and 0035 Airfoils in the Full-Scale Wind Tunnel

This report presents the results of an investigation conducted in the NACA full-scale wind tunnel to determine the aerodynamic characteristics of the 6 by 36-foot rectangular NACA 0025 and 0035 airfoils. The aerodynamic characteristics of the plain airfoils with rounded and square tips were determined by force tests through a complete angle-of-attack range, in addition, the profile drag was determined by the momentum method. The transition points on the airfoils were located by boundary-layer determinations with small total-head and static tubes. Each airfoil was also tested with a 0.20c full-span split flap. Tuft surveys were included to show the progressive breakdown of flow with increasing angles of attack. Previously published data from tests of the NACA 0009, 0012, and 0018 airfoils in the full-scale tunnel have been included in the summary curves.

Bullivant, W Kenneth↗