Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Improved Li-TiS2 cell cycling in ether-based electrolytes with synergistic additives

Results of the application of 2-MeF and KOH additives to improve the lithium stability in THF, dioxolane, and THF/2-MeTHF solvent-based electrolytes are presented. The stability of these electrolytes with and without additives is evaluated by microcalorimetry and AC impedance spectroscopy. A novel method, cathode turnover number, is proposed to represent the electrolyte performance in a given system. The lithium cycling efficiency and cathode turnover number of the electrolytes are calculated from the cycle life data in experimental Li-TiS2 cells. Overall, THF/2-MeTHF electrolyte containing 2-MeF and/or KOH exhibited higher stability, lithium cycling efficiency, and cathode turnover number compared to THF and dioxolane electrolytes with and without additives.

Shen, D. H.↗
NASA NTRS1993

NO(x) reduction additives for aircraft gas turbine engines

The reduction of oxides of nitrogen (NO(x)) emissions from aircraft gas turbine engines is a vital part of the NASA High Speed Research Program. Emissions reductions are critical to the feasibility of future High Speed Civil Transports which operate at supersonic speeds in the stratosphere. It is believed that large fleets of such aircraft using conventional gas turbine engines would emit levels of NO(x) that would be harmful to the stratospheric ozone layer. Previous studies have shown that NO(x) emissions can be reduced from stationary powerplant exhausts by the addition of additives such as ammonia to the exhaust gases. Since the exhaust residence times, pressures and temperatures may be different for aircraft gas turbines, a study has been made of additive effectiveness for high speed, high altitude flight.

Adelman, Henry G.↗
NASA NTRS1951

Theoretical and experimental investigation of additive drag

The significance of additive drag is discussed and equations for determining its approximate value are derived. Charts are presented giving values of additive drag for open-nose inlets and for annular-nose inlets with conical flow at the inlet. The effects of variable inlet total-pressure recovery and static pressures on the center body are investigated, and an analytical method of predicting the variation of pressure on the center body with mass-flow ratio is given. Experimental values of additive drag are compared with values predicted by the methods.

AIR INLETS↗
NASA NTRS1952

Pressure distribution and aerodynamic coefficients associated with heat addition to supersonic air stream adjacent to two-dimensional supersonic wing

The modifications in the pressure distributions and the aerodynamic coefficients associated with additions of heat to the two-dimensional supersonic in viscid flow field adjacetnt to the lower surface of of a 5-percent-thickness symmetrical circular-arc wing are presented in this report. The pressure distributions are obtained by the use of graphical method which gives the two-dimensional supersonic inviscid flow field obtained with moderate heat addition. The variation is given of the lift-drag ratio and of the aerodynamic coefficients of lift, drag, and moment with free stream Mach number, angle of attack, and parameters defining extent and amount of heat addition. The six graphical solutions used in this study included Mach numbers of 3.0 and 5.0 and angles of attack of 0 degrees and 2 degrees.

Pinkel, I Irving↗
NASA NTRS1955

Effect of Surface-active Additives on Physical Properties of Slurries of Vapor-process Magnesium

The presence of 3 to 5 percent surface-active additive gave the lowest Brookfield apparent viscosity, plastic viscosity, and yield value that were obtained for slurry fuels containing approximately 50 percent vapor-process magnesium in JP-1 fuel. The slurries settled little and were easily remixed. A polyoxyethylene dodecyl alcohol was the most effective of 13 additives tested in reducing the Brookfield apparent viscosity and the yield value of the slurry. The seven most effective additives all had a hydroxyl group plus an ester or polyoxethylene group in the molecule. The densities of some of the slurries were measured.

Pinns, Murray L↗
NASA NTRS1941

The Additional-Mass Effect of Plates as Determined by Experiments

The apparent increase in the inertia properties of a body moving in a fluid medium has been called the additional-mass effect. This report presents a resume of test procedures and results of experimental determinations of the additional-mass effect of flat plates. In addition to data obtained from various foreign sources and from a NACA investigation in 1933, the results of tests recently conducted by the National Advisory Committee for Aeronautics are included.

Gracey, William↗
NASA NTRS1993

Polyimide processing additives

A process for preparing polyimides having enhanced melt flow properties is described. The process consists of heating a mixture of a high molecular weight poly-(amic acid) or polyimide with a low molecular weight amic acid or imide additive in the range of 0.05 to 15 percent by weight of the additive. The polyimide powders so obtained show improved processability, as evidenced by lower melt viscosity by capillary rheometry. Likewise, films prepared from mixtures of polymers with additives show improved processability with earlier onset of stretching by TMA.

Pratt, J. Richard↗
NASA NTRS1994

Development and Preliminary Evaluation of Aryl Ester Boundary Additives for Perfluoropolyethers

A series of additives were developed for evaluation as boundary lubrication enhancers for perfluoropolyethers. They are composed of a hydrocarbon aryl component (for lubrication improvement) and a fluorinated side chain (for solubility enhancement). The two moieties are joined by an ester linkage. Five boundary additives were evaluated in a perfluoropolyether basestock (Fomblin Z25) using a specially designed four-ball apparatus. Additives were evaluated at a one wt percent concentration. Conditions included: an atmosphere of dry air at atmospheric pressure, a 200N load, a speed of 100 rpm, room temperature, and 440C stainless steel specimens. Two monoesters, 2,4,6-trimethyl E2 and H5PDFO yielded wear rate reductions of approximately 60 and 35 percent, respectively. One diester, H4(E2)(sub 2), had no activity, while two other diesters (a diester of bisphenol A and H4(E4)(sub 2)) were pro-wear.

Williams, John R.↗
NASA NTRS1994

Evaluation of the EHL Film Thickness and Extreme Pressure Additives on Gear Surface Fatigue Life

Surface pitting fatigue life tests were conducted with seven lubricants, using AISI 9310 spur gears. The test lubricants can be classified as synthetic polyol-esters with various viscosities and additive packages. The lubricant with a viscosity that provided a specific film thickness greater than one and with an additive package produced gear surface fatigue lives that were 8.6 times that for lubricants with a viscosity that provided specific film thickness less than one. Lubricants with the same viscosity and similar additive packages gave equivalent gear surface fatigue lives.

Townsend, Dennis P.↗
NASA NTRS1995

Transition-Metal Additives For Long-Life Na/NiCI(2) Cells

Transition-metal additives in cathodes of Na/NiCI(2) high-temperature, rechargeable electrochemical cells found to slow premature fading of charge/discharge capacity. Decline in capacity of cell attributed to agglomeration of Ni particles at cathode: this agglomeration reduces electrochemical area of cathode. Depending on choice of transition-metal additive for particular cell, additive might even participate in desired electrochemical reactions in cell, contributing to specific energy of cell.

Bugga, Ratnakumar V.↗
NASA NTRS1999

An Additive to Improve the Wear Characteristics of Perfluoropolyether Based Greases

The friction and wear characteristics of two formulated perfluoropolyether based greases were compared to their non-additive base greases. One grease was developed for the electronics industry (designated as GXL-296A) while the other is for space applications (designated as GXL-320A). The formulated greases (GXL-296B and GXL-320B) contained a proprietary antiwear additive at an optimized concentration. Tests were conducted using a vacuum four-ball tribometer. AISI 52100 steel specimens were used for all GXL-296 tests. Both AISI 52100 steel and 440C stainless steel were tested with the GXL-320 greases. Test conditions included: a pressure less than 6.7 x 10(exp )-4 Pa, a 200N load, a sliding velocity of 28.8 mm/sec (100 rpm) and room temperature (approximately equal to 23 C). Wear rates for each grease were determined from the slope of the wear volume as a function of sliding distance. Both non-additive base greases yielded relatively high wear rates on the order of 10(exp -8) cu mm using AISI 52100 steel specimens. Formulated grease GXL-296B yielded a reduction in wear rate by a factor of approximately 21, while grease GXL-320B had a reduction of approximately 12 times. Lower wear rates (-50%) were observed with both GXL-320 greases using 440C stainless steel. Mean friction coefficients were slightly higher for both formulated greases compared to their base greases. The GXL-296 series (higher base oil viscosity) yielded much higher friction coefficients compared to their GXL-320 series (lower base oil viscosity) counterparts.

Jones, David G. V.↗
NASA NTRS2001

Effects of Minor Alloying Additions on the Microstructure, Toughness, and Creep Strength of Directionally Solidified NiAl-31Cr-3Mo

A study of the effects of small (0.25 to 1.0 at%) fifth element additions to the structure and mechanical properties of directionally solidified (DS) NiAl-31Cr-3Mo has been undertaken. Essentially all the additions changed the as-DS'ed microstructure from lamellar eutectic grains to cells and, in some cases, introduced NiAl dendrites and/or third phases. In general the alloying additions did not improve strength or toughness over that possessed by the base composition; only Hf and, perhaps Ti, gave a minor increase in elevated temperature creep resistance. The lack of improvement in creep properties is probably due to inability to precipitation harden NiAl.

Whittenberger, J. D.↗
NASA NTRS2002

Phenylethynyl Containing Reactive Additives

Phenylethynyl containing reactive additives were prepared from aromatic diamines containing phenylethynyl groups and various ratios of phthalic anhydride and 4-phenylethynylphthalic anhydride in glacial acetic acid to form the imide in one step or in N-methyl-2-pyrrolidinone to form the amide acid intermediate. The reactive additives were mixed in various amounts (10% to 90%) with oligomers containing either terminal or pendent phenylethynyl groups (or both) to reduce the melt viscosity and thereby enhance processability. Upon thermal cure, the additives react and become chemically incorporated into the matrix and effect an increase in crosslink density relative to that of the host resin. This resultant increase in crosslink density has advantageous consequences on the cured resin properties such as higher glass transition temperature and higher modulus as compared to that of the host resin.

John W Connell↗
NASA NTRS2002

Phenylethynyl Containing Reactive Additives

Phenylethynyl containing reactive additives were prepared from aromatic diamine, containing phenylethvnvl groups and various ratios of phthalic anhydride and 4-phenylethynviphthalic anhydride in glacial acetic acid to form the imide in one step or in N-methyl-2-pvrrolidinone to form the amide acid intermediate. The reactive additives were mixed in various amounts (10% to 90%) with oligomers containing either terminal or pendent phenylethynyl groups (or both) to reduce the melt viscosity and thereby enhance processability. Upon thermal cure, the additives react and become chemically incorporated into the matrix and effect an increase in crosslink density relative to that of the host resin. This resultant increase in crosslink density has advantageous consequences on the cured resin properties such as higher glass transition temperature and higher modulus as compared to that of the host resin.

Connell, John W.↗
NASA NTRS2002

Continuous In Vitro Evolution of a Ribozyme that Catalyzes Three Successive Nucleotidyl Addition Reactions

Variants of the class I ligase ribozyme, which catalyzes joining of the 3' end of a template bound oligonucleotide to its own 5' end, have been made to evolve in a continuous manner by a simple serial transfer procedure that can be carried out indefinitely. This process was expanded to allow the evolution of ribozymes that catalyze three successive nucleotidyl addition reactions, two template-directed mononucleotide additions followed by RNA ligation. During the development of this behavior, a population of ribozymes was maintained against an overall dilution of more than 10(exp 406). The resulting ribozymes were capable of catalyzing the three-step reaction pathway, with nucleotide addition occurring in either a 5' yieldig 3' or a 3' yielding 5' direction. This purely chemical system provides a functional model of a multi-step reaction pathway that is undergoing Darwinian evolution.

McGinness, Kathleen E.↗
NASA NTRS2003

The Effect of Tungsten Additions on Disk Alloy CH98

Gas turbine engines for future subsonic transports will probably have higher pressure ratios which will require nickelbase superalloy disks with 1300 to 1400 F temperature capability. Several advanced disk alloys are being developed to fill this need. One of these, CH98, is a promising candidate for gas turbine engines and is being studied in NASA s Advanced Subsonic Technology (AST) program. For large disks, residual stresses generated during quenching from solution heat treatments are often reduced by a stabilization heat treatment, in which the disk is heated in the range of 1500 to 1600 F for several hours followed by a static air cool and age. The reduction in residual stress levels lessens distortion during machining of disks. Previous work on CH98 has indicated that stabilization treatments will decrease creep capability, however, tungsten additions appear to improve the creep capability of stabilized and aged CH98. In this study, a systematic variation of tungsten additions to CH98 was investigated. Specifically, the 1300 F tensile, creep, and fatigue crack growth properties of stabilized CH 98 were assessed with varying levels of tungsten additions.

Gayda, John↗
NASA NTRS1996

Possible effects of protracted exposure on the additivity of risks from space radiations

Conventional radiation risk assessments are presently based on the additivity assumption. This assumption states that risks from individual components of a complex radiation field involving many different types of radiation can be added to yield the total risk of the complex radiation field. If the assumption is not correct, the summations and integrations performed to obtain the presently quoted risk estimates are not appropriate. This problem is particularly important in the area of space radiation risk evaluation because of the many different types of high- and low-LET radiation present in the galactic cosmic ray environment. For both low- and high-LET radiations at low enough dose rates, the present convention is that the addivity assumption holds. Mathematically, the total risk, Rtot is assumed to be Rtot = summation (i) Ri where the summation runs over the different types of radiation present. If the total dose (or fluence) from each component is such that the interaction between biological lesions caused by separate single track traversals is negligible within a given cell, it is presently considered to be reasonable to accept the additivity assumption. However, when the exposure is protracted over many cell doubling times (as will be the case for extended missions to the moon or Mars), the possibility exists that radiation effects that depend on multiple cellular events over a long time period, such as is probably the case in radiation-induced carcinogenesis, may not be additive in the above sense and the exposure interval may have to be included in the evaluation procedure. It is shown, however, that "inverse" dose-rate effects are not expected from intermediate LET radiations arising from the galactic cosmic ray environment due to the "sensitive-window-in-the-cell-cycle" hypothesis.

NASA Discipline Number 45-10↗
NASA NTRS2004

Absorption Reveals and Hydrogen Addition Explains New Interstellar Aldehydes: Propenal and Propanal

New interstellar molecules propenal (CH2CHCHO) and propanal (CH3CH2CHO) have been detected largely in absorption toward the star-forming region Sagittarius B2(N) by means of rotational transitions observed with the 100-m Green Bank Telescope (GBT) operating in the range of 18 GHz (lambda approximately 1.7 cm) to 26 GHz (lambda approximately 1.2 cm). The GBT was also used to observe the previously reported interstellar aldehyde propynal (HC2CHO) in Sagittarius B2(N) which is known for large molecules believed to form on interstellar grains. The presence of these three interstellar aldehydes toward Sagittarius B2(N) strongly suggests that simple hydrogen addition on interstellar grains accounts for successively larger molecular species: from propynal to propenal and from propenal to propanal. Energy sources within Sagittarius B2(N) likely permit the hydrogen addition reactions on grain surfaces to proceed. This work demonstrates that successive hydrogen addition is probably an important chemistry route in the formation of a number of complex interstellar molecules. We also searched for but did not detect the three-carbon sugar glyceraldehyde (CH2OHCHOHCHO).

Hollis, J. M.↗