Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aircraft Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

A mathematical model for Vertical Attitude Takeoff and Landing (VATOL) aircraft simulation. Volume 2: Model equations and base aircraft data

Equations incorporated in a VATOL six degree of freedom off-line digital simulation program and data for the Vought SF-121 VATOL aircraft concept which served as the baseline for the development of this program are presented. The equations and data are intended to facilitate the development of a piloted VATOL simulation. The equation presentation format is to state the equations which define a particular model segment. Listings of constants required to quantify the model segment, input variables required to exercise the model segment, and output variables required by other model segments are included. In several instances a series of input or output variables are followed by a section number in parentheses which identifies the model segment of origination or termination of those variables.

Fortenbaugh, R. L.↗
NASA NTRS1989

Nonlinear control of a supermaneuverable aircraft

This paper describes a technique which may be used to design the flight control system for a highly maneuverable aircraft. The control system was provided to stabilize the dynamics of the aircraft model and allow it to fly simulated, poststall 'supermaneuvers'. Although the aircraft dynamics are highly nonlinear under these conditions, the gain-scheduled, flight control system was designed using basically linear techniques. A manuever generator was implemented to pilot the mathematical model through prescribed optimal trajectories. The control system design performed well while executing maneuvers involving small angular rates where the governing dynamics could be considered linear. However, the performance deteriorated once the model was subjected to high angular rates at high angle of attack.

Snell, S. Antony↗
NASA NTRS1996

Structural dynamic model obtained from flight use with piloted simulation and handling qualities analysis

The ability to use flight data to determine an aircraft model with structural dynamic effects suitable for piloted simulation. and handling qualities analysis has been developed. This technique was demonstrated using SR-71 flight test data. For the SR-71 aircraft, the most significant structural response is the longitudinal first-bending mode. This mode was modeled as a second-order system, and the other higher order modes were modeled as a time delay. The distribution of the modal response at various fuselage locations was developed using a uniform beam solution, which can be calibrated using flight data. This approach was compared to the mode shape obtained from the ground vibration test, and the general form of the uniform beam solution was found to be a good representation of the mode shape in the areas of interest. To calibrate the solution, pitch-rate and normal-acceleration instrumentation is required for at least two locations. With the resulting structural model incorporated into the simulation, a good representation of the flight characteristics was provided for handling qualities analysis and piloted simulation.

Powers, Bruce G.↗
NASA NTRS1991

The NASA Lewis integrated propulsion and flight control simulator

A new flight simulation facility was developed at NASA-Lewis. The purpose of this flight simulator is to allow integrated propulsion control and flight control algorithm development and evaluation in real time. As a preliminary check of the simulator facility capabilities and correct integration of its components, the control design and physics models for a short take-off and vertical landing fighter aircraft model were shown, with their associated system integration and architecture, pilot vehicle interfaces, and display symbology. The initial testing and evaluation results show that this fixed based flight simulator can provide real time feedback and display of both airframe and propulsion variables for validation of integrated flight and propulsion control systems. Additionally, through the use of this flight simulator, various control design methodologies and cockpit mechanizations can be tested and evaluated in a real time environment.

Bright, Michelle M.↗
NASA NTRS2016

Simulation-Based Airframe Noise Prediction of a Full-Scale, Full Aircraft

A previously validated computational approach applied to an 18%-scale, semi-span Gulfstream aircraft model was extended to the full-scale, full-span aircraft in the present investigation. The full-scale flap and main landing gear geometries used in the simulations are nearly identical to those flown on the actual aircraft. The lattice Boltzmann solver PowerFLOW® was used to perform time-accurate predictions of the flow field associated with this aircraft. The simulations were performed at a Mach number of 0.2 with the flap deflected 39 deg. and main landing gear deployed (landing configuration). Special attention was paid to the accurate prediction of major sources of flap tip and main landing gear noise. Computed farfield noise spectra for three selected baseline configurations (flap deflected 39 deg. with and without main gear extended, and flap deflected 0 deg. with gear deployed) are presented. The flap brackets are shown to be important contributors to the farfield noise spectra in the mid- to high-frequency range. Simulated farfield noise spectra for the baseline configurations, obtained using a Ffowcs Williams and Hawkings acoustic analogy approach, were found to be in close agreement with acoustic measurements acquired during the 2006 NASA-Gulfstream joint flight test of the same aircraft.

Khorrami, Mehdi R.↗
NASA NTRS1978

Longitudinal aerodynamic characteristics of a fighter model with a close-coupled canard at Mach numbers from 0.40 to 1.20

A Au aircraft model with a close-coupled canard mounted above the wing chord plane was considered. Model angle of attack was varied from -4 deg to 15 deg; canard incidence was varied from -5 deg to 18 deg; and selected canard and wing flap deflections were investigated. By using the canard incidence for trim, maximum trimmed lift-drag ratios of about 8.8, 7.7, and 4.7 were obtained at free-stream Mach numbers of 0.40, 0.90, and 1.20, respectively. At a lift coefficient of 0.60, model trim angle of attack could be varied over an incremental range between 3.0 deg and 3.8 deg, depending on Mach number, by different combinations of control settings. At high lift coefficients, larger trimmed lift-drag ratios were obtained by using the deflection capability of the canard leading- and trailing-edge flaps before increasing canard incidence angle.

Re, R. J.↗
NASA NTRS1991

High angle of attack control law development for a free-flight wind tunnel model using direct eigenstructure assignment

Flight-control laws are developed for a wind-tunnel aircraft model flying at a high angle of attack by using a synthesis technique called direct eigenstructure assignment. The method employs flight guidelines and control-power constraints to develop the control laws, and gain schedules and nonlinear feedback compensation provide a framework for considering the nonlinear nature of the attack angle. Linear and nonlinear evaluations show that the control laws are effective, a conclusion that is further confirmed by a scale model used for free-flight testing.

Wendel, Thomas R.↗
NASA NTRS1990

Modeling and control design of a wind tunnel model support

The 12-Foot Pressure Wind Tunnel at Ames Research Center is being restored. A major part of the restoration is the complete redesign of the aircraft model supports and their associated control systems. An accurate trajectory control servo system capable of positioning a model (with no measurable overshoot) is needed. Extremely small errors in scaled-model pitch angle can increase airline fuel costs for the final aircraft configuration by millions of dollars. In order to make a mechanism sufficiently accurate in pitch, a detailed structural and control-system model must be created and then simulated on a digital computer. The model must contain linear representations of the mechanical system, including masses, springs, and damping in order to determine system modes. Electrical components, both analog and digital, linear and nonlinear must also be simulated. The model of the entire closed-loop system must then be tuned to control the modes of the flexible model-support structure. The development of a system model, the control modal analysis, and the control-system design are discussed.

Howe, David A.↗
NASA NTRS1991

Modeling and control design of a wind tunnel model support

The 12-Foot Pressure Wind Tunnel at Ames Research Center is being restored. A major part of the restoration is the complete redesign of the aircraft model supports and their associated control systems. An accurate trajectory control servo system capable of positioning a model (with no measurable overshoot) is needed. Extremely small errors in scaled-model pitch angle can increase airline fuel costs for the final aircraft configuration by millions of dollars. In order to make a mechanism sufficiently accurate in pitch, a detailed structural and control-system model must be created and then simulated on a digital computer. The model must contain linear representations of the mechanical system, including masses, springs, and damping in order to determine system modes. Electrical components, both analog and digital, linear and nonlinear must also be simulated. The model of the entire closed-loop system must then be tuned to control the modes of the flexible model-support structure. The development of a system model, the control modal analysis, and the control-system design are discussed.

Howe, David A.↗
NASA NTRS2000

Validation of Aircraft Noise Prediction Models at Low Levels of Exposure

Aircraft noise measurements were made at Denver International Airport for a period of four weeks. Detailed operational information was provided by airline operators which enabled noise levels to be predicted using the FAA's Integrated Noise Model. Several thrust prediction techniques were evaluated. Measured sound exposure levels for departure operations were found to be 4 to 10 dB higher than predicted, depending on the thrust prediction technique employed. Differences between measured and predicted levels are shown to be related to atmospheric conditions present at the aircraft altitude.

Page, Juliet A.↗
NASA NTRS2000

Validation of Aircraft Noise Prediction Models at Low Levels of Exposure

Aircraft noise measurements were made at Denver International Airport for a period of four weeks. Detailed operational information was provided by airline operators which enabled noise levels to be predicted using the FAA's Integrated Noise Model. Several thrust prediction techniques were evaluated. Measured sound exposure levels for departure operations were found to be 4 to 10 dB higher than predicted, depending on the thrust prediction technique employed. Differences between measured and predicted levels are shown to be related to atmospheric conditions present at the aircraft altitude.

Page, Juliet A.↗
NASA NTRS1973

Noise measurements from a large-scale lift fan transport in the 40- by 80-foot wind tunnel

Noise data measurements from a large scale lift fan transport model aircraft were made in the 40- by 80-foot wind tunnel. The model had two lift fans in deep inlets in the forward fuselage and two lift-cruise fans in pods on the aft fuselage. The noise data measurements are presented as listings and plots of sounds pressure level versus 1/3-octave center frequency.

Atencio, A., Jr.↗