SEARCH · Search NASA

Results for “Axial Force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Rotating Balances Used for Fluid Pump Testing

Marshall Space Flight Center has developed and demonstrated two direct read force and moment balances for sensing and resolving the hydrodynamic loads on rotating fluid machinery. These rotating balances consist of a series of stainless steel flexures instrumented with semiconductor type, unidirectional strain gauges arranged into six bridges, then sealed and waterproofed, for use fully submerged in degassed water at rotational speeds up to six thousand revolutions per minute. The balances are used to measure the forces and moments due to the onset and presence of cavitation or other hydrodynamic phenomena on subscale replicas of rocket engine turbomachinery, principally axial pumps (inducers) designed specifically to operate in a cavitating environment. The balances are inserted into the drive assembly with power to and signal from the sensors routed through the drive shaft and out through an air-cooled twenty-channel slip ring. High frequency data - balance forces and moments as well as extensive, flush-mounted pressures around the rotating component periphery - are acquired via a high-speed analog to digital data acquisition system while the test rig conditions are varied continuously. The data acquisition and correction process is described, including the in-situ verifications that are performed to quantify and correct for known system effects such as mechanical imbalance, "added mass," buoyancy, mechanical resonance, and electrical bias. Examples of four types of cavitation oscillations for two typical inducers are described in the laboratory (pressure) and rotating (force) frames: 1) attached, symmetric cavitation, 2) rotating cavitation, 3) attached, asymmetric cavitation, and 4) cavitation surge. Rotating and asymmetric cavitation generate a corresponding unbalanced radial force on the rotating assembly while cavitation surge generates an axial force. Attached, symmetric cavitation induces no measurable force. The frequency of the forces can be determined a priori from the pressure environment while the magnitude of the hydrodynamic force is proportional to the pressure unsteadiness.

Skelley, Stephen↗

NASA NTRS1984

Four New Capabilities in NASTRAN for Dynamic and Aeroelastic Analyses of Rotating Cyclic Structures

Static aerothermoelastic design/analysis of axial-flow compressors, modal flutter analysis of axial-flow turbomachines, forced vibration analysis of rotating cyclic structures and modal flutter analysis of advanced turbopropellers with highly swept blades are four new capabilities developed and implemented in NASTRAN Level 17.7. The contents, applicability and usefulness of these capabilities which were developed and documented under the sponsorship of NASA's Lewis Research Center are discussed. Overall flowcharts and selected examples are presented.

Elchuri, V.↗

NASA NTRS1985

Importance of Gravity for Plant Growth and Behavior

Flight experiments on the importance of gravity to plant growth and behavior are reported. The following studies were undertaken: (1) hyperastic responses to incremental changes of an axially imposed centripetal force; (2) Spacelab-1 experiments, methods for preparing soil in flight hardware containers were impound, to ensure desired moisture content and minimal contamination probability; (3) mesocotyl growth patterns were established by Avena lore exposure to red light during early seedling outogency; (4) the development of flight hardware; (5) choice of member of seedlings in each cube; (6) data processing and reduction; (7) clinostat validation; circummutation in space was more vigorous than on Earth based clinostat.

Brown, A. H.↗

NASA NTRS1987

Method for the determination of the three-dimensional aerodynamic field of a rotor-stator combination to compressible flow

Using the lifting surface theory and the acceleration potential method for the flow field of an axial turbocompressor stage, a recursive and a direct method are presented that make use of the eigenfunction solutions of the isolated rotor and stator to solve for the rotor-stator interaction problem. The net pressure distribution on the rotor and stator blades is represented by modified Birnbaum series, whose coefficients are determined using a matrix procedure and satisfying the boundary conditions on the surface of the blades. The relation between the matrix operators of the recursive and the direct methods is also shown. Expressions have been given for the blade circulation, the axial and tangential forces on the blade, the rotor power required, and the induced upwash velocity of the stage.

Ramachandra, Sridhar M.↗

NASA NTRS1987

Method for the determination of the three dimensional aerodynamic field of a rotor-stator combination in compressible flow

Ramachandra, Sridhar M.↗

NASA NTRS1992

Application of ceramic superconductors in high speed turbines

A turbine system was modified to adapt melt textured YBa2Cu3O(7-delta) (YBCO) with high energy permanent magnets to form a hybrid superconducting magnetic bearing (HSMB). The HSMB/turbine prototype has achieved a static axial thrust capacity exceeding 41 N/sq cm (60 psi) and a radial magnetic stiffness of 7 N/mm in a field cooled state at 77 K. A comparison was made between different configurations of magnets and superconductor for radial stability, axial instability, and force hystereses. This systematic study lead to a greater understanding of the interactions between YBCO and high energy permanent magnets to define design parameters for high rotational devices using the HSMB design.

Mcmichael, C. K.↗

NASA NTRS1993

Testing Machine Exerts Longitudinal And Transverse Loads

Hydraulic load frame for testing materials applies both longitudinal uniaxial tension and transverse bending force simultaneously. Includes axial and transverse hydraulic actuators mounted on pivots to eliminate coupling effects between two loading modules.

Gardner, Mickey R.↗

NASA NTRS1994

Concepts of flywheels for energy storage using autostable high-T(sub c) superconducting magnetic bearings

A flywheel for energy storage using autostable high-T(sub c) superconducting magnetic bearings has been built. The rotating disk has a total weight of 2.8 kg. The maximum speed is 9240 rpm. A process that allows accelerated, reliable and reproducible production of melt-textured superconducting material used for the bearings has been developed. In order to define optimum configurations for radial and axial bearings, interaction forces in three dimensions and vertical and horizontal stiffness have been measured between superconductors and permanent magnets in different geometries and various shapes. Static as well as dynamic measurements have been performed. Results are being reported and compared to theoretical models.

Bornemann, Hans J.↗

NASA NTRS1998

Three-axis force actuator for a magnetic bearing

This invention features a three-axis force actuator that axially, radially and rotatably supports a bearing member for frictionless rotation about an axis of rotation generally coincident with a Z-axis. Also featured is a magnetic bearing having such an actuator. The actuator includes an inner member, a magnetic member and a pole assembly having a ring member and four pole extending therefrom. The poles are equi-angular spaced from each other and radially spaced about the Z-axis. The inner member extends along the Z-axis and is a highly magnetic permeable material. The magnetic member is formed about the inner member outer surface, extends along the Z-axis and is configured so one magnetic pole polarity is located at its outer surface and the other polarity pole is located at its inner surface. Preferably, the magnetic member is a radially magnetized permanent magnet. The inner surface of the ring member is magnetically coupled to the magnetic member and a face of each pole is coupled to the bearing member. The magnetic member, the pole assembly, the inner member and the bearing member cooperate to generate a magnetic field that radially and rotatably supports a rotating member secured to the bearing member. The actuator further includes a plurality of electromagnetic coils. Preferably, a coil is formed about each pole and at least 2 coils are formed about the inner member. When energized, the electromagnetic coils generate a modulated magnetic field that stabilizes the rotating member in the desired operational position.

Gondhalekar, Vijay↗

NASA NTRS2019

Influence of Strain-Gage Balance Characteristics on the Precision Error of the Drag Coefficient

Improvements and results of a new method are presented that computes a pre-test estimate of the precision error of the drag coefficient of a wind tunnel model. The error estimate is defined as the part of the drag coefficient's precision error that is primarily associated with the precision error of the angle of attack measurement and physical characteristics of the chosen strain-gage balance. The method indirectly describes the precision error of the angle of attack measurement by using an assumed balance gage output variation of one microV/V. The physical characteristics of the balance, on the other hand, are described by partial derivatives of the axial and normal forces with respect to the strain-gage outputs. These derivatives can directly be obtained from the data reduction matrix of the balance. The precision error estimate itself is calculated by applying a simple explicit equation that uses the model reference area, the dynamic pressure, the angle of attack, the coefficients of the linear terms of the data reduction matrix, and the electrical output variation of one microvolt per volt as input. Precision errors at constant angle of attack may be visualized as contour plots by plotting them, for example, versus the Mach number and the total pressure. Characteristics of NASA's MC60E balance are used in combination with the reference area of a generic wind tunnel model in order to demonstrate that error estimates are independent of both the balance load format and the units chosen for the description of balance loads, model reference area, and the dynamic pressure. Finally, experimental data from a wind tunnel test of the Ames Check Standard Model in the NASA Ames 11-foot Transonic Wind Tunnel illustrates the application of the method to real-world test data.

precision error↗

NASA NTRS1988

Turbomachinery rotor forces

The fluid-induced forces, both steady and unsteady, acting upon an impeller of a centrifugal pump, and impeller blade-diffuser vane interaction in centrifugal pumps with vaned radial diffusers were evaluated experimentally and theoretically. Knowledge of the steady and unsteady forces, and the associated rotordynamic coefficients are required to effectively model the rotor dynamics of the High Pressure Fuel Turbopump (HPFTP) of the Space Shuttle Main Engine (SSME). These forces and rotordynamic coefficients were investigated using different impellers in combination with volutes and vaned diffusers, and axial inducers. These rotor forces are global. Local forces and pressures are also important in impeller-diffuser interaction, for they may cause cavitation damage and even vane failures. Thus, in a separate investigation, impeller wake, and impeller blade and diffuser vane pressure measurements were made. The nature of the rotordynamic forces is discussed, the experimental facility is described, and the measurements of unsteady forces and pressure are reported together with a brief and incomplete attempt to calculate these flows.

Arndt, Norbert↗

NASA NTRS1973

Nondestructive shell-stability estimation by a combined-loading technique.

The variation of specimen lateral stiffness with compressive axial loading is studied experimentally, and it is demonstrated that buckling loads can be predicted for monocoque shells from such data. A study of the initial specimen geometry is presented, and an evaluation is made of its effect on the distribution of stiffness at zero axial load. When the lateral test force used to determine the stiffness is considered as a destabilizing load in combination with the axial compression, it is shown that critical values of the force can be estimated by the 'Southwell plot' procedure. These critical forces can be correlated with axial load and extrapolated to yield an accurate estimate of the buckling load.

Craig, J. I.↗

NASA NTRS1997

Bevel Gear Driver and Method Having Torque Limit Selection

Methods and apparatus are provided for a torque driver including an axially displaceable gear with a biasing assembly to bias the displaceable gear into an engagement position. A rotatable cap is provided with a micrometer dial to select a desired output torque. An intermediate bevel gear assembly is disposed between an input gear and an output gear. A gear tooth profile provides a separation force that overcomes the bias to limit torque at a desired torque limit. The torque limit is adjustable and may be adjusted manually or automatically depending on the type of biasing assembly provided. A clutch assembly automatically limits axial force applied to a fastener by the operator to avoid alteration of the desired torque limit.

Cook, Joseph S., Jr.↗

NASA NTRS2017

Gradient Field Imploding Liner Fusion Propulsion System

Magneto-inertial fusion concepts often use a pulsed high current discharge in a cylindrical coil to generate a rapidly changing axial magnetic field, inducing a counter-propagating current in the conducting outer liner of a centrally aligned cylindrical fusion target. The Lorentz force arising from the axial field and azimuthal liner current rapidly implodes the target radially inward, compressing the fuel to reach fusion conditions.

Exploration↗

NASA NTRS1977

Nutations of sunflower seedlings on tilted clinostats

The kinetics of hypocotyl nutations in Helianthus annuus L. were measured on plants which were rotated on clinostats with axes of rotation inclined at various angles, alpha, away from the vertical. The g-force component acting in the direction of the plant axis was taken as g cos alpha. The average period and average amplitude of nutation were constant for all such axially directed g-forces between 1.0 and 0.2 g (vertical to about 80 inclination). On the horizontal clinostat (90 inclination) nutation was neither initiated nor sustained. The g-force just sufficient fully to activate nutational oscillations should be sought for g-force parameter values ranging from 0 to 0.2.

Brown, A. H.↗

NASA NTRS1989

Simultaneous axial conduction in the fluid and the pipe wall for forced convective laminar flow with blowing and suction at the wall

Numerical solutions are reported for conjugate heat transfer in a porous pipe having an internal flow with blowing or suction at the inner surface of the pipe and constant heat flux at the outer surface. The effect of the simultaneous axial conduction through the wall and the fluid has been studied for the combined hydrodynamic and thermal entry lengths. The results show that the ratio of the thermal conductivities of the pipe wall to the fluid and the thickness of the pipe wall may become significant factors on the heat transfer when the Peclet number is small, especially for the case when fluid is injected into the pipe. It is also shown that the effect of axial wall conduction for the case of constant heat flux at the outer wall surface can be neglected when the wall thickness is small and the ratio of the conductivities of the wall to the fluid approaches unity.

Faghri, Amir↗

NASA NTRS2000

Melt Motion Due to Peltier Marking During Bridgman Crystal Growth with an Axial Magnetic Field

This paper treats a liquid-metal flow inside an electrically insulating cylinder with electrically conducting solids above and below the liquid region. There is a uniform axial magnetic field, and there is an electric current through the liquid and both solids. Since the lower liquid-solid interface is concave into the solid and since the liquid is a better electrical conductor than the adjacent solid, the electric current is locally concentrated near the centerline. The return to a uniform current distribution involves a radial electric current which interacts with the axial magnetic field to drive an azimuthal flow. The axial variation of the centrifugal force due to the azimuthal velocity drives a meridional circulation with radial and axial velocities. This problem models the effects of Peltier marking during the vertical Bridgman growth of semiconductor crystals with an externally applied magnetic field, where the meridional circulation due to the Peltier Current may produce important mixing in the molten semiconductor.

Sellers, C. C.↗

NASA NTRS1999

Unshrouded Centrifugal Turbopump Impeller

The ratio of rocket engine thrust to weight is a limiting constraint in placing more payload into orbit at a low cost. A key component of an engine's overall weight is the turbopump weight, Reducing the turbopump weight can result in significant engine weight reduction and hence, increased delivered payload. There are two main types of pumps: centrifugal and axial pumps. These types of pumps can be further sub-divided into those with shrouds and those without shrouds (unshrouded pumps). Centrifugal pumps can achieve the same pump discharge pressure as an axial pump and it requires fewer pump stages and lower pump weight than an axial pump. Also, with unshrouded centrifugal pumps (impeller), the number of stages and weight can be further reduced. However. there are several issues with regard to using an unshrouded impeller: 1) there is a pump performance penalty due to the front open face recirculation flow; 2) there is a potential pump axial thrust problem from the unbalanced front open face and the back shroud face; and, 3) since test data is very linu'ted for this configuration, there is uncertainty in the magnitude and phase of the rotordynamics forces due to the front impeller passage. The purpose of the paper is to discuss the design of an unshrouded impeller and to examine the design's hydrodynamic performance, axial thrust, and rotordynamics performance. The design methodology will also be discussed. This work will help provide some guidelines for unshrouded impeller design. In particular, the paper will discuss the design of three unshrouded impellers - one with 5 full and 5 partial blades (5+5). one with 6+6 blades and one with 8+8 blades. One of these designs will be selected for actual fabrication and flow test. Computational fluid dynamics (CFD) is used to help design and optimize the unshrouded impeller. The relative pump performance penalty is assessed by comparing the CFD results of the unshrouded impeller with the equivalent shrouded impeller for a particular design. Limited unshrouded - versus - shrouded impeller data from the J-2 pump is used to anchor the CFD. Since no detailed impeller blade force data is available, axial thrust and rotordynamic force predictions are based on the CFD model. For the axial thrust, the impeller front flow passage axial force is integrated from the CFD results and compared to the equivalent shrouded impeller axial force. For the rotordynamics forces, the fluid reaction forces are computed from unsteady flow CFD results using a moving boundary method; the rotor- shaft is moved at several whirl-to-speed frequency ratios to extract the rotordynamics coefficients.

Prueger, George↗