Search NASA⌕ Search

SEARCH · Search NASA

Results for “BRAZING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Compressive behavior of titanium alloy skin-stiffener specimens selectively reinforced with boron-aluminum composite

A method of selectively reinforcing a conventional titanium airframe structure with unidirectional boron-aluminum composite attached by brazing was successfully demonstrated in compression tests of short skin-stiffener specimens. In a comparison with all-titanium specimens, improvements in structural performance recorded for the composite-reinforced specimens exceeded 25 percent on an equivalent-weight basis over the range from room temperature to 700 K (800 F) in terms of both initial buckling and maximum strengths. Performance at room temperature was not affected by prior exposure at 588 K (600 F) for 1000 hours in air or by 400 thermal cycles between 219 K and 588 K (-65 F and 600 F). The experimental results were generally predictable from existing analytical procedures. No evidence of failure was observed in the braze between the boron-aluminum composite and the titanium alloy.

Herring, H. W.↗
NASA NTRS1972

Beryllium heat shield technology in the area of thermal protection devices

For future space applications, it is important that thermal protection systems be reusable for space shuttle flights. Beryllium offers a unique combination of properties for use as a heat shield material (stiffness, lightweight, ability to absorb heat). In order to adequately test these properties, it was necessary to fabricate heat shields. The concept used was a two-section test panel 99.1 x 99.1 cm (39 x 39 inch) with each section made of two 0.051 cm (0.020 inch) thick beryllium corrugations brazed together as a mirror image, with titanium (Ti-6Al-4V) used as standoffs to support the panel structure. The work prior to fabrication included brazability of both beryllium and titanium, forming of beryllium and titanium, machining processes involving beryllium and chem-milling beryllium. Sub-scale samples were made of all details before actual fabrication of the large panel. The full scale test panel was hot-formed at 950 K, chem-milled to 0.041 + or - 0.005 cm (0.016 + or - 0.002 inches), trimmed, vacuum brazed, drilled and assembled.

Muhl, A. E.↗
NASA NTRS1972

Compressive strength of titanium alloy skin-stringer panels selectively reinforced with boron-aluminum composite.

Description of a method of selectively reinforcing conventional titanium airframe structure with unidirectional boron-aluminum composite attached by brazing which has been successfully demonstrated based on compression tests of short skin-stringer panels. Improvements in structural performance exceeded 25% on an equivalent weight basis over the range from room temperature to 800 F, both in terms of initial buckling and maximum strengths. Room-temperature performance was not affected by prior exposure at 600 F for 1000 hours in air, or by 400 cycles between -65 and 600 F. The experimental results were generally predictable on the basis of existing analytical procedures. No evidence of failure was observed in the braze bond between the boron-aluminum composite and the titanium alloy.

Herring, H. W.↗
NASA NTRS1972

Evaluation of tantalum 316 stainless steel transition joints

Tubular transition joints providing a metallurgically bonded connection between tantalum and 316 stainless steel pipe sections were comparatively evaluated for durability under thermal cycling conditions approximating the operation of a SNAP-8 mercury boiler. Both coextruded and vacuum brazed transition joints of 50mm (2 inch) diameter were tested by thermal cycling 100 times between 730 C and 120 C(1350 F and 250 F) in a high vacuum environment. The twelve evaluated transition joints survived the full test sequence without developing leaks, although liquid penetrant bond line indications eventually developed in all specimens. The brazed transition joints exhibited the best dimensional stability and bond line durability.

Stoner, D. R.↗
NASA NTRS1972

State-of-technology for joining TD-NiCr sheet.

At the current state-of-technology there are many joining processes that can be used to make sound welds in TD-NiCr sheet. Some of these that are described in this report are electron beam welding (EBW), gas-tungsten arc welding (GTAW), diffusion welding (DFW), resistance spot welding (RSW), resistance seam welding (RSEW), and brazing. Roll welding (RW) and explosion welding (EXW) have not been developed to the point where they can be used to make sound welds in TD-NiCr. Joining work that has previously been done on TD-NiCr by various organizations, both privately supported and under Air Force and NASA contracts, is described in this summary. Current work is also described that is being done at General Dynamics/Convair (under NASA contract) and at NASA/Lewis to develop and evaluate DFW, RSW, RSEW, and brazing. Preliminary comparisons of joining processes are made for typical applications. A brief description of the manufacture of TD-NiCr sheet by a recently standardized process (under NASA contract) also is given.

Holko, K. H.↗
NASA NTRS1951

Experimental Investigation of Air-Cooled Turbine Blades in Turbojet Engine. 7: Rotor-Blade Fabrication Procedures

An experimental investigation was conducted to determine the cooling effectiveness of a wide variety of air-cooled turbine-blade configurations. The blades, which were tested in the turbine of a - commercial turbojet engine that was modified for this investigation by replacing two of the original blades with air-cooled blades located diametrically opposite each other, are untwisted, have no aerodynamic taper, and have essentially the same external profile. The cooling-passage configuration is different for each blade, however. The fabrication procedures were varied and often unique. The blades were fabricated using methods most suitable for obtaining a small number of blades for use in the cooling investigations and therefore not all the fabrication procedures would be directly applicable to production processes, although some of the ideas and steps might be useful. Blade shells were obtained by both casting and forming. The cast shells were either welded to the blade base or cast integrally with the base. The formed shells were attached to the base by a brazing and two welding methods. Additional surface area was supplied in the coolant passages by the addition of fins or tubes that were S-brazed. to the shell. A number of blades with special leading- and trailing-edge designs that provided added cooling to these areas were fabricated. The cooling effectiveness and purposes of the various blade configurations are discussed briefly.

Long, Roger A.↗
NASA NTRS1974

Research study on materials processing in space experiment number M512

Conclusions of the team of specialists can be generalized as: (1) Brazing and welding of metal structures in an orbital near zero gravity condition are quite feasible. (2) Design of joints for fabrication in zero gravity will place less emphasis on the tolerances and proximity of the adjacent structures than on the quantity of liquid metal available. (3) Brazing of metallic joints has many advantages over electron beam welding for practical reasons: simplicity, launch weight, development costs, joint design tolerances, remotization, etc. (4) No evidence of different physical or mechanical properties of liquid metals in zero gravity was observed. However, many differences in liquid behavior were observed. Many of these effects have been called adhesion-cohesion phenomena.

Tobin, J. M.↗
NASA NTRS1973

Research study on materials processing in space experiment number M512

Adhesion of the melted metals to the adjacent solid metals, and cohesion of the liquid metal to itself appeared to be equally as strong in zero gravity as on earth. Similar cut edge bead periodicity in cut thin plate, and similar periodic chevron patterns in full penetration welds were seen. The most significant practical result is that the design of braze joints for near zero gravity can be very tolerant of dimensional gaps in the joint. This conclusion is based on a comparison of narrow, wide and variable gap widths. Brazing is very practical as a joining or repairing technique for metal structures at zero gravity. The operation of the hardware developed to locate successive small (0.6 cm) diameter cylinders in the focus of the battery powered EB unit, melt the various metal specimens and deploy some liquid metal drops to drift in space, was generally successful. However, the sphericity and surface roughness were far from those of ball bearings.

Tobin, J. M.↗
NASA NTRS1973

Design fabrication, testing, and delivery of shuttle heat pipe leading edge test modules. Volume 1: Executive summary

The construction of two test modules is presented for a feasibility demonstration of a concept for reusable space shuttle wing leading edge surfaces. In this leading edge concept high temperature heat pipes were incorporated into the structure to cool the stagnation region, allowing the use of super-alloys in place of refractory metal, ablator protected, or carbon-carbon structures. The program included the analysis and design of the heat pipes, their integration into the test module structure, heat pipe development testing, construction of the test modules and a facility adapter, and formulation of recommended testing conditions. The results of the heat pipe and leading edge module thermal analyses indicate the test modules will meet the design goal; reducing the leading edge temperature at the stagnation line from 1315 C (2400 F) to less than 1010 C (1850 F). The development tests demonstrated that the module assembly could be brazed with active heat pipes, as was borne out by the subsequent successful brazing of both modules with active heat pipes loaded with sodium.

Source record↗
NASA NTRS1974

Physical forces influencing Skylab experiments M551, M552, and M553

The forces concerned with metals melting, exothermic brazing, and sphere forming experiments on Skylab 1 mission are reported. The conclusions reached are that no significant practical differences exist between terrestrial and microgravity electron beam melting, and braze gap clearances are far less critical to joining operations in space than on earth. Altered microstructures, increased grain refinement, and the appearance of a single, large interior shrinkage pore were found in the Skylab specimens.

Bourgeois, S. V.↗
NASA NTRS1974

Discipline report on thermal analyses of M551, M552, and M553 experiments

Reduced gravity does not significantly affect the thermal histories in the M551 specimen, even if molten metal flow pattern is different from that in terrestrial conditions. Thermal histories corresponding to terrestrial experimental conditions were calculated by use of the computer programs. Heat conduction through brazing alloy (M552 experiment) is improved in the Skylab conditions, because of the increased extent, rate and uniformity of braze spreading in space. Effects of reduced gravity on heat flow in the M553 specimen are insignificant, because convection effects appear instantaneously and conduction is a governing factor on the heat flow.

Muraki, T.↗
NASA NTRS1974

Nondestructive tests of regenerative chambers

The capabilities and limitations of nondestructive evaluation methods were studied to detect and locate bond deficiencies in regeneratively cooled thrust chambers for rocket engines. Flat test panels and a cylinder were produced to simulate regeneratively cooled thrust chamber walls. Planned defects with various bond integrities were produced in the panels to evaluate the sensitivity, accuracy, and limitations of nondestructive methods to define and locate bond anomalies. Holography, acoustic emission, and ultrasonic scan were found to yield sufficient data to discern bond quality when used in combination and in selected sequences. Bonding techniques included electroforming and brazing. Materials of construction included electroformed nickel bonded to Nickel 200 and OFHC copper, electroformed copper bonded to OFHC copper, and 300 series stainless steel brazed to OFHC copper. Variations in outer wall strength, wall thickness, and defect size were evaluated for nondestructive test response.

Malone, G. A.↗
NASA NTRS1976

Braze/Rebraze process for CRES steel

Using induction brazing process with 8.5-Au/16.5-Cu/2.0-Ni braze alloy, joints in 21-6-9 CRES steel tubing can be reworked up to seven times, thus significantly reducing cost of fabrication, repair, and part replacement.

Silverman, C. E.↗
NASA NTRS1976

Development of explosive welding procedures to fabricate channeled nozzle structures

Research was conducted to demonstrate the feasibility of fabricating a large contoured structure with complex internal channeling by explosive welding procedures. Structures or nozzles of this nature for wind tunnel applications were designed. Such nozzles vary widely in their complexity. However, in their simplest form, they consist of a grooved base section to which a cover sheet is attached to form a series of internal cooling passages. The cover sheet attachment can be accomplished in various ways: fusion welding, brazing, and diffusion welding. The cover sheet has also been electroformed in place. Of these fabrication methods, brazing has proved most successful in producing nozzles with complex contoured surfaces and a multiplicity of internal channels.

Pattee, H. E.↗
NASA NTRS1976

Metal melting, joining, and alloying under weightlessness

During the Skylab mission experiments were conducted concerning the influence of weightlessness on molten metals and the solidification process. It was found that the absence of gravity-induced thermal convection and sedimentation modified the properties of the bulk melt. A metals melting experiment was conducted to study the behavior of metal melted by an electron beam and to evaluate the feasibility of joining metals in space. An exothermic brazing experiment investigated the spreading, mixing, and capillary flow of molten braze material. The containerless melting and solidification of small samples of several metals was studied in another experiment. A description is also given of a study of the directional solidification of solid solution alloys.

Snyder, R. S.↗
NASA NTRS1980

Thermal jack

Auxiliary furnace tool forces part to match length of mating part during brazing. As brazed assembly cools, jack contracts faster and disengages from fitting studs.

Armenoff, C. T.↗
NASA NTRS1978

Advanced fabrication techniques for cooled engine structures

An improved design for regeneratively cooled engine structures was identified. This design uses photochemically machined (PCM) coolant passages. It permits the braze joint to be placed in a relatively cool area, remote from the critical hot face sheet. The geometry of the passages at the face sheet also minimizes stress concentration and, therefore, enhances the low cycle fatigue performance. The two most promising alloys identified for this application are Inconel 617 and Nickel 201. Inconel 617 was selected because it has excellent creep rupture properties, while Nickel 201 was selected because of its predicted good performance under low cycle fatigue loading. The fabrication of the PCM coolant passages in both Inconel 617 and Nickel 201 was successfully developed. During fabrication of Inconel 617, undesirable characteristics were observed in the braze joints. A development program to resolve this condition was undertaken and led to definition of an isothermal solidification process for joining Inconel 617 panels. This process produced joints which approach parent metal strength and homogeneity.

Buchmann, O. A.↗
NASA NTRS1980

A precoat prevents ceramic stopoffs from spalling

Nickel-alloy precoat applied with plasmagun improves adhesion of ceramic materials applied to protect areas from unintentional brazing. Metal surface should be grit-blasted before precoating. Coating does not interfere with brazing or contaminate vacuum pumping systems.

Brennan, A.↗