Search NASA⌕ Search

SEARCH · Search NASA

Results for “CAPTURE EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Computational study of the aerodynamics and control by blowing of asymmetric vortical flows over delta wings

The complicated flowfield around a rounded leading-edge delta wing was calculated at angles of attack and yaw with and without tangential leading-edge blowing, using thin-layer Navier-Stokes equations. The effectiveness of blowing for providing roll control at high angle of attack was illustrated, and the saturation effect of increased blowing was captured well. The effect of sideslip was shown to be analogous to asymmetric blowing.

Craig, Ken↗
NASA NTRS2008

Testing, Modeling and System Impact of Metabolic Heat Regenerated Temperature Swing Adsorption

Metabolic heat regenerated temperature swing adsorption (MTSA) technology is being developed for removal and rejection of carbon dioxide (CO2) and heat from a portable life support system (PLSS) to the Martian environment. Previously, hardware was built and tested to demonstrate using heat from simulated, dry ventilation loop gas to affect the temperature swing required to regenerate an adsorbent used for CO2 removal. New testing has been performed using a moist, simulated ventilation loop gas to demonstrate the effects of water condensing and freezing in the heat exchanger during adsorbent regeneration. In addition, thermal models of the adsorbent during regeneration were modified and calibrated with test data to capture the effect of the CO2 heat of desorption. Finally, MTSA impact on PLSS design was evaluated by performing thermal balances assuming a specific PLSS architecture. Results using NASA s Extravehicular Activity System Sizing Analysis Tool (EVAS_SAT), a PLSS system evaluation tool, are presented.

Lacomini, Christine S.↗
DOE OSTI2020

Radiation-resistant metal-organic framework enables efficient separation of krypton fission gas from spent nuclear fuel

Capture and storage of volatile radionuclides that result from processing of used nuclear fuel is a major challenge. Solid adsorbents, in particular ultra-microporous metal-organic frameworks, could be effective in capturing these volatile radionuclides, including 85 Kr. However, metal-organic frameworks are found to have higher affinity for xenon than for krypton, and have comparable affinity for Kr and N 2 . Also, the adsorbent needs to have high radiation stability. To address these challenges, here we evaluate a series of ultra-microporous metal-organic frameworks, SIFSIX-3-M (M = Zn, Cu, Ni, Co, or Fe) for their capability in 85 Kr separation and storage using a two-bed breakthrough method. These materials were found to have higher Kr/N 2 selectivity than current benchmark materials, which leads to a notable decrease in the nuclear waste volume. The materials were systematically studied for gamma and beta irradiation stability, and SIFSIX-3-Cu is found to be the most radiation resistant.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1990

The effects of streamline curvature and swirl on turbulent flows in curved ducts

A technique for improving the numerical predictions of turbulent flows with the effect of streamline curvature is developed. Separated flows, the flow in a curved duct, and swirling flows are examples of flow fields where streamline curvature plays a dominant role. A comprehensive literature review on the effect of streamline curvature was conducted. New algebraic formulations for the eddy viscosity incorporating the kappa-epsilon turbulence model are proposed to account for various effects of streamline curvature. The loci of flow reversal of the separated flows over various backward-facing steps are employed to test the capability of the proposed turbulence model in capturing the effect of local curvature. The inclusion of the effect of longitudinal curvature in the proposed turbulence model is validated by predicting the distributions of the static pressure coefficients in an S-bend duct and in 180 degree turn-around ducts. The proposed turbulence model embedded with transverse curvature modification is substantiated by predicting the decay of the axial velocities in the confined swirling flows. The numerical predictions of different curvature effects by the proposed turbulence models are also reported.

Cheng, Chih-Hsiung↗
NASA NTRS1992

On turbulent flows dominated by curvature effects

A technique for improving the numerical predictions of turbulent flows with the effect of streamline curvature is developed. Separated flows and the flow in a curved duct are examples of flowfields where streamline curvature plays a dominant role. New algebraic formulations for the eddy viscosity incorporating the k-epsilon turbulence model are proposed to account for various effects of streamline curvature. The loci of flow reversal of the separated flows over various backward-facing steps are employed to test the capability of the proposed turbulence model in capturing the effect of local curvature.

Cheng, G. C.↗
DOE OSTI2024

Mapping TpPa-1 covalent organic framework (COF) molecular interactions in mixed solvents via atomistic modeling and experimental study

Complex solvent environments continue to limit the widespread adoption of organic solvent nanofiltration (OSN) in many chemical industry applications. In this paper we employ a commercially available covalent organic framework (COF), TpPa-1, and force field models to molecularly map separation performance of TpPa-1 membrane in mixed solvents. To minimize time and length scale mismatch between atomistic modeling and experiments, solvent permeance was normalized with water in modeling and experimental results to enable direct comparison. Model outputs, such as organic solvent permeance and solute rejection rate, matched well with filtration results. Since the atomistic models assume that all mass transfer is via through-pore transport, the discrepancies between modeling and experimental results provide insights on the effect of linear polymer defects, adsorption and interstitial mass transfer on polycrystalline COF membrane performance. In sum, force field models can serve as digital twins of COF membranes to simulate separation processes while capturing the effects of COF structure, chemistry, and crystallinity on membrane performance in complex organic solvent environments. Finally, this approach will provide insight into future COF design and synthesis for persisting separation challenges.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

A mechanistic, multiscale model for predicting Pd penetration in TRISO fuels using BISON

TRistructural ISOtropic (TRISO) particles use silicon carbide (SiC) as the primary structural member and barrier against metallic fission product (FP) release. palladiums (PDs), produced by fission in the fuel kernel, can diffuse to and chemically interact with the SiC layer, degrading its structural integrity and ability to contain radioactive FPs. Existing temperature-dependent correlations for predicting Pd penetration rely on experimental data with significant scatter due to varying conditions, potentially complicating ongoing fuel qualification and licensing efforts for advanced reactors that would subject TRISO fuels to operating conditions outside of those examined in the experiments. A mechanistic model of Pd production, transport, and reaction is developed in this work to better understand and predict PD attack of SiC in TRISO particles. molecular dynamicss (MDs) simulations are utilized to calculate the Pd diffusivity in SiC grain bulk and grain boundaries. A mesoscale phase-field diffusion model, informed by the MD diffusivities, is used to develop a reduced order model (ROM) for the effect of SiC microstructure on the Pd penetration rate. The engineering scale BISON model calculates Pd production and transport, utilizing the ROM to predict penetration rates consistent with experimental data. This novel mechanistic ROM captures the effect of temperature, microstructure, and irradiation history on Pd penetration. In conclusion, these new capabilities are expected to support ongoing qualification and licensing efforts associated with near-term TRISO-fueled reactor applications.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

An improved pressure drop correlation for modeling localized effects in a pebble bed reactor

Advances in the development of pebble bed reactors (PBRs) has created a desire for accurate and cost-effective simulation tools for design scoping studies and safety analysis. The current state-of-the-art for these simulations is the use of porous media models, although these models rely on correlations to capture the effects of flow features that are not explicitly modeled. One of the areas where correlation accuracy is currently lacking is in the near-wall region of the bed. In this region, the presence of the wall causes the pebbles to pack more orderly, drastically changing the geometry and flow behavior in this region. This work presents a new generalized pressure drop correlation for PBRs based on the KTA equation. A high-to-low methodology is applied, where large eddy simulation (LES) is performed on two beds of 1568 and 1700 pebbles to generate a high-fidelity dataset. The flow fields are then averaged in time and separated into concentric rings of 0.05 D peb width. Average porosity, velocity, and pressure drop are extracted for each ring and the friction and form losses are calculated. The Reynolds number range for this study is 625–10,000, and thus the form losses are dominant over the friction losses. The form losses across the rings are investigated, and a correction term for the form loss calculation is determined and applied to the KTA equation to drastically improve the capability of modeling localized porosity effects in a porous media code. Finally, the improved correlation reduces near-wall velocity prediction error from over 50% with the KTA correlation to around 5%. Agreement in pressure drop prediction between LES and porous media simulations is also improved.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Implementation of a 9-point stencil in SOLPS-ITER and implications for Alcator C-Mod divertor plasma simulations

The SOLPS-ITER code suite is used worldwide for plasma edge modeling, the interpretation of experiments, as well as for the design of the ITER divertor. The numerical scheme of the plasma solver of the code, B2.5, is based on the assumption of perfectly field-aligned grids, while in practice grids are often strongly distorted to match divertor target shapes. Neglecting these grid distortion leads to qualitatively and quantitatively incorrect results for fluid neutral simulations, and may affect results in cold (detached) divertors even when using kinetic neutral simulations. In this contribution, we present the first results of a newly implemented 9-point stencil in B2.5 to properly handle misaligned grids. The new scheme is then applied to fluid neutral simulations of a well-diagnosed and previously modeled Alcator C-Mod discharge. Results are compared with the original 5-point scheme neglecting grid distortion effects, as well as with simulations including a full kinetic neutral model. We conclude that the 9-point stencil is essential to correctly model the transport of fluid neutrals on distorted grids, and to capture the effects of divertor closure on the fluid neutral behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2012

SRMS Assisted Docking and Undocking for the Orbiter Repair Maneuver

As part of the Orbiter Repair Maneuver (ORM) planned for Return to Flight (RTF) operations, the Shuttle Remote Manipulator System (SRMS) must undock the Orbiter, maneuver it through a complex trajectory at extremely low rates, present it to an EVA crewman at the end of the Space Station Remote Manipulator System to perform the Thermal Protection System (TPS) repair, and then retrace back through the trajectory to dock the Orbiter with the Orbiter Docking System (ODS). The initial and final segments of this operation involve the interaction between the SRMS, ISS, Orbiter and ODS. Previously, a technique entitled "SRMS assisted docking" for installation of a payload to the ODS had been developed and was utilized for the Russian provided Docking Module on STS-74 during Shuttle-Mir missions and both the Node 1 and FGB elements on STS-88/Flight 2A. This procedure consisted of the SRMS grappling the respective payload, maneuvering it to a pre-install position inches above the ODS Androgynous Peripheral Attachment System (APAS) ring, commanding the SRMS into Test mode (which allows brakes-off motion of the joints), and then down-firing Primary Reaction Control System (PRCS) jets in order to effect a capture of the APAS latches. Once a successful capture had been achieved, then the AP AS was operated through its nominal retraction sequence to complete the mating sequence. While this technique can once again be used for the tail end docking portion of the ORM, the initial undocking of the orbiter and ISS vehicles with the assistance of the SRMS has yet to be attempted on orbit. The objective here is to determine the most efficient means to separate or extract the vehicles. Two techniques were analyzed in support of RTF: (1) the 'nominal' demating from the mated interface, and (2) the SRMS performing the operation (either in an active or passive fashion). In the first operation, the demating process would replicate standard undocking operations, with the exception that the SRMS is allowed to arrest the resulting motion. The second operation would be to extend the APAS ring to a ready to dock position, open the capture latches, and then detach the vehicles using the SRMS either actively or passively. In the active case, the APAS ring is extended and latched, and the SRMS is commanded to pull the two interfaces apart (assuming that the effective pull force of the SRMS can overcome the spec values of the combined latch resistance). In the passive case, the SRMS brakes are engaged and the AP AS mechanism is commanded to retract, pulling the two interfaces apart. Since the emphasis of both STS-74 and STS-88 had solely been on the installation operation, as opposed to the separation operation, two new models required development and incorporation within simulation tools designed to analyze those scenarios. These enhancements included: (1) a detailed demating dynamics model to characterize the pusher spring characteristics during undocking, and (2) contact and mechanical system modeling of the back side of the latches to represent unlatching dynamics. This paper first provides an overview of the Monte-Carlo screening analysis for the installation (both nominal and contingency), including the variation of separation distance, misalignment conditions, SRMS joint/brake parameter characteristics, and PRCS jet combinations and corresponding thrust durations. The resulting 'optimum' solution is presented based on trade studies between predicted capture success and integrated system loads. This paper then discusses the upgrades to the APAS math model associated with the new SRMS assisted undocking technique and reviews simulation results for various options investigated for either the active and passive separation of the ISS from the Orbiter.

Space Station Remote Manipulator System↗
DOE OSTI2022

Solvated Nuclear–Electronic Orbital Structure and Dynamics

Nonadiabatic dynamical processes such as proton-coupled electron transfer and excited state intramolecular proton transfer have been the subject of much research. One of the promising theoretical methods to describe these processes is the nuclear–electronic orbital (NEO) approach. This approach inherently accounts for nuclear quantum effects within quantum chemistry calculations, and it has recently been extended to directly simulate nonadiabatic processes with the development of real-time NEO methods. These processes can also be significantly dependent on the surrounding chemical environment, however, and capturing the effects of the environment is often necessary for analyzing experimentally relevant systems. This work couples the NEO density functional theory and real-time time-dependent density functional theory approaches with solvation through the polarizable continuum model. Here, the effects of this coupling are investigated for ground state properties, solvent-dependent vibrational frequencies, and direct excited state intramolecular proton transfer dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1998

Thermal Effects Modeling Developed for Smart Structures

Applying smart materials in aeropropulsion systems may improve the performance of aircraft engines through a variety of vibration, noise, and shape-control applications. To facilitate the experimental characterization of these smart structures, researchers have been focusing on developing analytical models to account for the coupled mechanical, electrical, and thermal response of these materials. One focus of current research efforts has been directed toward incorporating a comprehensive thermal analysis modeling capability. Typically, temperature affects the behavior of smart materials by three distinct mechanisms: Induction of thermal strains because of coefficient of thermal expansion mismatch 1. Pyroelectric effects on the piezoelectric elements; 2. Temperature-dependent changes in material properties; and 3. Previous analytical models only investigated the first two thermal effects mechanisms. However, since the material properties of piezoelectric materials generally vary greatly with temperature (see the graph), incorporating temperature-dependent material properties will significantly affect the structural deflections, sensory voltages, and stresses. Thus, the current analytical model captures thermal effects arising from all three mechanisms through thermopiezoelectric constitutive equations. These constitutive equations were incorporated into a layerwise laminate theory with the inherent capability to model both the active and sensory response of smart structures in thermal environments. Corresponding finite element equations were formulated and implemented for both the beam and plate elements to provide a comprehensive thermal effects modeling capability.

Lee, Ho-Jun↗
DOE OSTI2020

The Effects of Synthesis Conditions on the Carbon Capture Capacity of Polyethylenimine Impregnated Protonated Titanate Nanotubes

Capture and storage of carbon dioxide emitted from power plants, which burn fossil fuels, is one of the best ways to mitigate climate change. Polyethylenimine (PEI) impregnated protonated titanate nanotubes (PEI-PTNTs) are efficient amine-modified solid adsorbents for post combustion carbon capture. This study is to investigate the effects of synthesis conditions of titanate nanotubes on the carbon capture capacity of PEI-PTNTs. PTNTs are synthesized using hydrothermal treatment of TiO 2 anatase powder at different temperatures and in different days, followed by washing with dilute HCl solution and deionized water. PEI-PTNTs are prepared by loading PEI (M.W. = 10,000) onto PTNTs at a weight ratio of 1:1 using a wet impregnation process. PTNTs and PEI-PTNTs are characterized using transmission electron microscopy, porosity and surface area analysis, powder X-ray diffraction, and Fourier transform infrared spectroscopy. CO 2 adsorption is conducted at 75 °C using simulated flue gas, and CO 2 desorption is performed at 110 °C by purging the adsorbent with dry nitrogen gas. CO 2 adsorption experiments demonstrate that the PEI-PTNTs synthesized at 130 °C within 3 or 5 days, have the highest CO 2 capture capacity. These optimized PEI-PTNTs have a significant potential to capture CO 2 from power plants.

Materials Science↗
DOE OSTI2025

Analysis of the impact of parallel magnetic fluctuations on linear gyrokinetic stability in NSTX-U and verification of gyro-fluid models

In this work, we use the CGYRO gyrokinetic code to analyze two L- and one H-mode discharges from the National Spherical Torus Experiment (NSTX) and NSTX-Upgrade (NSTX-U) selected due to their different mix of ion-scale driftwaves, ion temperature gradient (ITG) mode and trapped electron mode (TEM), and electromagnetic instabilities, kinetic ballooning mode (KBM), and micro-tearing mode (MTM) in the plasma core. It is found that the effect of parallel magnetic fluctuations is strongly destabilizing to the unstable KBMs compared to calculations with only perpendicular magnetic fluctuations. Two discharges have a mix of ITG/TEM and MTMs that are predicted to be dominant instability across the plasma radius. The parallel magnetic fluctuations are found to have little effect on the MTM stability but are destabilizing to ITG/TEM modes. To test the validity of the gyro-fluid linear stability codes TGLF and GFS at low aspect ratio, a database of linear growth rates has been created using the CGYRO gyrokinetic code. The database is comprised of various parameter scans around a standardized set of NSTX-U core parameters. It contains a group of electrostatic cases and an electromagnetic group that includes the effects of perpendicular and parallel magnetic fluctuations. Comparing the results from the GFS and TGLF models, we find that GFS exhibits the best agreement with the database of CGYRO linear growth rates. Comparing the model results for the electromagnetic scans shows that GFS captures the effects of parallel magnetic fluctuations accurately, while the TGLF model does not, as it lacks sufficient perpendicular energy resolution.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Chapter 38: Aerodynamics of Wake Steering

This chapter discusses the mechanisms that enable wake steering within a wind farm with a focus on wake steering performed using yaw misaligned turbines as this is the most popular approach to wake steering, although there are others. Wake steering is a type of wind farm control in which wind turbines in a wind farm operate with an intentional yaw misalignment to mitigate the effects of its wake on downstream turbines in order to increase overall combined wind farm energy production. This chapter goes into detail regarding the dominant aerodynamic characteristics that are present when a turbine operates in yaw misaligned conditions and suggests analytical models that can capture these effects. A detailed analysis of large-scale flow structures generated in wind farm control through yaw misalignment is presented. A collection of counter-rotating vortices, produced from a misaligned turbine, deforms the shape of the wake and produces asymmetric effects with oppositely signed yaw angles. These vortices generated by an upstream misaligned turbine can also deflect wakes of downstream non-misaligned turbines. This chapter also addresses the importance of modeling these counter-rotating vortices in analytical models for wind farm control design and for accurately quantifying the impacts of wake steering on gains in power production in larger wind farms.

modeling↗
DOE OSTI2026

Operational Parameter Database for Molten Salt Thermal Energy Storage Tank Modeling

The second generation of concentrated solar power (CSP) plants is characterized by the use of a central receiver (either cavity or external), two molten nitrate salt tanks (60 wt.% NaNO 3 and 40 wt.% KNO 3 ), and a steam Rankine power-generation cycle connected through a primary heat exchanger. Molten salt thermal energy storage (TES) tanks have been widely deployed in commercial CSP plants worldwide and have been essential for increasing plant dispatchability and capacity factor, while also reducing the levelized cost of electricity (LCOE). These systems enable energy storage at the gigawatt-hour scale, typically providing 6 to 17 hours of storage duration. Despite being a commercial technology, the multiple failures observed after only a few months or years of operation in plants around the world demonstrate the technology's relative infancy and highlight the need for further research to improve its reliability. The National Laboratory of the Rockies (NLR), in collaboration with industry partners and academic and research institutions, has been leading multiple projects funded by the U.S. Department of Energy (DOE). These projects focus on addressing molten salt tank failures by improving tank design and welding fabrication practices, evaluating new alloys and weld fillers, and providing guidelines for tank commissioning and safe operation. In particular, this report presents modeling results on the effect of key tank operation parameters during 60 minutes of operation, including the mass flow rate and temperature of the salt inflow, tank salt inventory temperature, and inventory level for a representative molten salt tank design. These results form a database of tank operation behaviors that captures the effects of each specific parameter during charging, charging/discharging, and discharging processes.

14 SOLAR ENERGY↗
DOE OSTI2020

Quantitative assessment of environmental phenomena on maximum pit size predictions in marine environments

Maximum pit sizes were predicted for dilute and concentrated NaCl and MgCl 2 solutions as well as sea-salt brine solutions corresponding to 40% relative humidity (RH) (MgCl 2 -rich) and 76% RH (NaCl-rich) at 25 °C. A quantitative method was developed to capture the effects of various cathode evolution phenomena including precipitation and dehydration reactions. Additionally, the sensitivity of the model to input parameters was explored. Despite one's intuition, the highest chloride concentration (roughly 10.3 M Cl – ) did not produce the largest predicted pit size as the ohmic drop was more severe in concentrated MgCl 2 solutions. Therefore, the largest predicted pits were calculated for saturated NaCl (roughly 5 M Cl – ). Next, it was determined that pit size predictions are most sensitive to model input parameters for concentrated brines. However, when the effects of cathodic reactions on brine chemistry are considered, the sensitivity to input parameters is decreased. Although there was not one main input parameter that influenced pit size predictions, two main categories were identified. Under similar chloride concentrations (similar RH), the water layer thickness (WL), and pit stability product, (i · x) sf , are the most influential factors. When varying chloride concentrations (RH), changes in WL, the brine specific cathodic kinetics on the external surface (captured in the equivalent current density (i eq )), and conductivity (k o ) are the most influential parameters. Finally, it was noted that dehydration reactions coupled with precipitation in the cathode will have the largest effect on predicted pit size, and cause the most significant inhibition of corrosion damage.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Energy-Storage Modeling: State-of-the-Art and Future Research Directions

Given its physical characteristics and the range of services that it can provide, energy storage raises unique modeling challenges. This paper summarizes capabilities that operational, planning, and resource-adequacy models that include energy storage should have and surveys gaps in extant models. Existing models that represent energy storage differ in fidelity of representing the balance of the power system and energy-storage applications. Modeling results are sensitive to these differences. The importance of capturing chronology can raise challenges in energy-storage modeling. Some models ‘decouple’ individual operating periods from one another, allowing for natural decomposition and rendering the models relatively computationally tractable. Energy storage complicates such a modeling approach. Improving the representation of the balance of the system can have major effects in capturing energy-storage costs and benefits.

25 ENERGY STORAGE↗