Search NASA⌕ Search

SEARCH · Search NASA

Results for “Child”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

The SSME seal test program: Leakage tests for helically-grooved seals

Helically grooved annular seal configurations were tested in highly turbulent flow to determine if reduced leakage and enhanced stability would result from the pumping action of the seal. It was found that: (1) leakage of a helically grooved seals decreases with running speed; (2) leakage reduction due to increased running speed is greater at lower values of R sub a; (3) an asymptote for leakage reduction is indicated with increasing running speed; (4) leakage is reduced by reducing the ridge (minimum) and average clearances; (5) leakage increases with increasing pitch angles and with increasing groove depth. Plain seals with smooth rotors and stators will leak more than a helically grooved seal. It was also found that plain seals with a rough rotor and a rough stator leak less than a properly designed helically grooved seal. A properly designed helically grooved seal consumes at least twice as much power as a conventional annular seal.

Childs, D. W.↗
NASA NTRS1984

Rotordynamic Characteristics of the HPOTP (High Pressure Oxygen Turbopump) of the SSME (Space Shuttle Main Engine)

Rotational stability of turbopump components in the space shuttle main engine was studied via analysis of component and structural dynamic models. Subsynchronous vibration caused unacceptable migration of the rotor/housing unit with unequal load sharing of the synchronous bearings that resulted in the failure of the High Pressure Oxygen Turbopump. Linear analysis shows that a shrouded inducer eliminates the second critical speed and the stability problem, a stiffened rotor improves the rotordynamic characteristics of the turbopump, and installing damper boost/impeller seals reduces bearing loads. Nonlinear analysis shows that by increasing the "dead band' clearances, a marked reduction in peak bearing loads occurs.

Childs, D. W.↗
NASA NTRS1984

SSME interstage seal research

Test results comprising direct and transverse force coefficients and leakage coefficients are reported for six seal configurations. All seals tested use the same smooth rotor and have the same constant minimum clearance. The following stator configurations were tested: (1) Smooth, (2) knurled pattern, (3) axially-grooved pattern with end seals, (4) diamond-grid roughened, (5) diamond-grid roughened with end seals, and (6) round-hole pattern. Comparison of the seals shows the Knurled-pattern stator to be the stiffest and the round-hole pattern stator to yield the largest net damping and the least leakage. The theory of reference is shown to substantially underestimate the stiffness and effective-added-mass coefficients, but do a reasonable job in predicting the net-damping-force coefficient.

Childs, D. W.↗
NASA NTRS1984

A comparison of experimental and theoretical results for leakage, pressure distribution, and rotordynamic coefficients for annular gas seals

The importance of seal behavior in rotordynamics is discussed and current annular seal theory is reviewed. A Nelson's analytical-computational method for determining rotordynamic coefficients for this type of compressible-flow seal is outlined. Various means for the experimental identification of the dynamic coefficients are given, and the method employed at the Texas A and M University (TAMU) test facility is explained. The TAMU test apparatus is described, and the test procedures are discussed. Experimental results, including leakage, entrance-loss coefficients, pressure distributions, and rotordynamic coefficients for a smooth and a honeycomb constant-clearance seal are presented and compared to theoretical results from Nelson's analysis. The results for both seals show little sensitivity to the running speed over the test range. Agreement between test results and theory for leakage through the seal is satisfactory. Test results for direct stiffness show a greater sensitivity to fluid pre-rotation than predicted. Results also indicate that the deliberately roughened surface of the honeycomb seal provides improved stability versus the smooth seal.

Nicks, C. O.↗
NASA NTRS1984

A Newton multigrid method for the Euler equations

A multigrid method is used to apply Newton's method to the Euler equations in a two dimensional curvilinear coordinate system. The objective is to obtain rapid convergence for steady state problems. Solutions computed with the method evolve in a non-time-like manner. Stable pressure distributions typically develop in eight to ten Newton-multigrid steps, which is equivalent to the computational work of about 70 iterations with a factored implicit algorithm.

Childs, R. E.↗
NASA NTRS1984

Vibration characteristics of the HPOTP (High-Pressure Oxygen Turbopump) of the SSME (Space Shuttle Main Engine)

Attention is given to rotor dynamic problems that have been encountered and eliminated in the course of Space Shuttle Main Engine (SSME) development, as well as continuing, subsynchronous problems which are being encountered in the development of a 109-percent power level engine. The basic model for the SSME's High Pressure Oxygen Turbopump (HPOTP) encompasses a structural dynamic model for the rotor and housing, and component models for the liquid and gas seals, turbine clearance excitation forces, and impeller diffuser forces. Linear model results are used to examine the synchronous response and stability characteristics of the HPOTP, with attention to bearing load and stability problems associated with the second critical speed. Differences between linear and nonlinear model results are discussed and explained in terms of simple models. Simulation results indicate that while synchronous bearing loads can be reduced, subsynchronous motion is not eliminated by seal modifications.

Childs, D. W.↗
NASA NTRS1984

An iwatsubo-based solution for labyrinth seals - comparison with experimental results

The basic equations are derived for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equation. The first-order equations are solved by a separation of variables solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to published test results.

Childs, D. W.↗
NASA NTRS1984

Analysis and testing for rotordynamic coefficients of turbulent annular seals with different, directionally homogeneous surface-roughness treatment for rotor and stator elements

A theory is presented, based on a simple modification of Hirs' turbulent lubrication equations, to account for different but directionally-homogeneous surface roughness treatments for the rotor and stator of annular seals. The theoretical results agree with von Pragenau's predictions that a damper seal which uses a smooth rotor and a rough stator yields more net damping than a conventional seal which has the same roughness for both the rotor and stator. Experimental results for four stators confirm that properly-designed roughened stators yield higher net damping values and substantially less leakage than seals with smooth surfaces. The best seal from both damping and leakage viewpoints uses a round-hole-pattern stator. Initial results for this stator suggest that, within limits, seals can be designed to yield specified ratios of stiffness to damping.

Childs, D. W.↗
NASA NTRS1985

Theory versus experiment for the rotordynamic coefficients of annular gas seals. Part 2: Constant clearance and convergent-tapered geometry

The leakage and rotordynamic coefficients of constant-clearance and convergent-tapered annular gas seals were measured in an experimental test facility. The results are presented along with the theoretically predicted values. Of particular interest is the prediction that optimally tapered seals have significantly larger direct siffness than straight seals. The experimental results verify this prediction. Generally the theory does quite well, but fails to predict the large increase in direct stiffness when the fluid is pre-rotated.

Nelson, C. C.↗
NASA NTRS1983

Theory versus experiment for the rotordynamic coefficients of annular gas seals. Part 1: Test facility and apparatus

A facility and apparatus are described for determining the rotordynamic coefficients and leakage characteristics of annular gas seals. The apparatus has a current top speed of 8000 cpm with a nominal seal diameter of 15.24 cmn (6 in). The air supply unit yields a seal pressure ratio of approximately 7. An external shaker is used to excite the test rotor. The capability to independently calculate all rotordynamic coefficients at a given operating condition with one excitation frequency are discussed.

Childs, D. W.↗
NASA NTRS1985

Vibration characteristics of the HPOTP (High Pressure Oxygen Turbopump) of the SSME (Space Shuttle Main Engine)

A review is presented of various rotordynamic problems which have been encountered and eliminated in developing the current flight engines, and continuing subsynchronous problems which are being encountered in developing a 109% power level engine. The basic model for the High Pressure Oxygen Turbopump (HPOTP) of the SSME including the structural dynamic model for the rotor and housing and component models for the liquid and gas seals, turbine-clearance excitation forces, and impeller-diffuser forces are discussed. Results from a linear model are used to examine the synchronous response and stability characteristics of the HPOTP, examining bearing load and stability problems associated with the second critical speed. Various seal modifications are examined and shown to have favorable consequences with respect to bearing reactions and stability.

Childs, D. W.↗
NASA NTRS1985

SSME seal test program: Test results for hole-pattern damper seals

The results consisting of direct and transverse force coefficients are presented for thirteen, hole-pattern, damper-seal configurations. The designation damper seal refers to a seal which uses a deliberately roughened stator nd smooth rotor, to increase the net damping force developed by a seal. The designation hole-pattern refers to a stator roughness pattern which is developed by a pattern of round holes while are milled into the stator. All seals tested use the same smooth rotor and have the same constant minimum clearance. The seal tests examined the following major design options: (1) hole-area density, i.e., the proportion of stator surface area consumed by holes; and (2) hole depth, particularly the ratio of hole depth to minimum clearance. In addition, limited data were taken to examine the influence of in-line versus staggered hole patterns and flat-bottomed versus spherical-bottomed holes.

Childs, D. W.↗
NASA NTRS1985

A comparison of experimental and theoretical results for rotordynamic coefficients of four annular gas seals

The test facility and initial test program developed to experimentally measure the fluid forces induced by annular gas seals is described. A comparison of theoretically predicted and experimentally obtained data for smooth and honeycomb seals is provided. And a comparison of experimental data from the tests of three smooth-rotor/smooth-stator seals is provided. The leakage of the working fluid through the seal, the pressure gradient along the seal length, entrance pressure-loss data, and rotordynamic coefficients provide a basis for comparison. A short discussion on seal theory is included, and various rotordynamic coefficient identification schemes are described.

Childs, D. W.↗
NASA NTRS1984

Analysis and testing for rotordynamic coefficients of turbulent annular seals with different, directionally-homogeneous surface-roughness treatment for rotor and stator elements

A combined analytical-computational method has been developed to calculate the transient pressure field and rotordynamic coefficients for high-pressure annular seals. The solution procedure applies to constant-clearance or the convergent tapered geometries of multistage centrifugal pumps which may have different surface roughness conditions on the stator and rotor seal elements. In experimental calculations with the method, the turbulent equations of Hirs (1973) are modified slightly to account for different surface roughness conditions, and a perturbation analysis is employed to develop zeroth and first order perturbation equations. Zeroth equations are also used to define both the leakage and circumferential flow due to shear stresses around the stator and rotor surfaces. The solution to analytical equations for four different surface roughnesses confirm the predicted net damping for the seals. A round-holed stator pattern yielded the highest net damping and lowest leakage of all the seals tested.

Childs, D. W.↗
NASA NTRS1984

Convergent-tapered annular seals - Analysis and testing for rotordynamic coefficients

A combined analytical-computational method has been developed to calculate the pressure field and dynamic coefficients for tapered high-pressure annular seals. Completely developed turbulent flow is assumed in both the circumferential and axial directions, according to Hirs' (1973) bulk-flow turbulent-lubrication equations. In a numerical experiment with the method, a short bearing approximation is used to derive an analytical expression for the first-order (dynamic) pressure gradient. This expression is integrated numerically to define dynamic coefficients of the seal. Numerical results of the integration are compared with previous results for straight and tapered seals. It is found that direct stiffness and leakage coefficients increase in the present seal, while the remaining coefficients decrease. An optimal taper angle is shown to exist with respect to: (1) the direct stiffness and (2) the ratio of direct stiffness to leakage. On the basis of the optimal taper angle calculations, stiffness increases on the order of 40 to 50 percent are predicted. Experimental results for three taper angles are presented, and are found to be in good agreement with the theoretical predictions.

Childs, D. W.↗
NASA NTRS1985

The passive control of compressible boundary layer growth by boundary layer trips

The passive control of compressible boundary layer growth by boundary layer trips has been studied experimentally. Axisymmetric trips and three dimensional trips were used in this study. The nomial freestream Mach numbers are 1.5 and 4. The results show that trips are effective in promoting boundary layer growth. Trips are more effective for Mach 1.5 flows than for Mach 4 flows.

Chou, J. H.↗
NASA NTRS1983

Extraction of cloud cover parameters from multispectral satellite measurements

An approach to the extraction of cloud cover parameters from multispectral satellite measurements is proposed which combines the best features of the threshold method and of the cluster approach. The approach proposed here utilizes radiative transfer equations, as in the threshold method, along with the identification of clusters in the two-dimensional histogram formed by the visible and 11-micron infrared channels. Information from a third channel, at 3.7 microns, is used to determine the microphysical model of the cloud particles. Examples of applications of the proposed approach are presented.

Arking, A.↗