Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compatibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Material Compatibility of Elastomers Used in the Salt Waste Processing Facility(SWPF)

Near the beginning of calendar year 2021, Salt Waste Processing Facility (SWPF) processed nearly a million gallons of initially diluted, and subsequently undiluted, supernatant. Higher than usual levels of Isopar L were detected in the Decontaminated Salt Solution (DSS). After shutting down the process and inspecting the DSS coalescers, personnel discovered the coalescers media appeared deformed and at least one had extruded out of the sealing surfaces. The gasket material was removed and sent to the Savannah River National Laboratory to possibly determine the cause of gasket degradation. A memorandum was issued documenting the results that could not rule out assembly error of the coalescer. For example, over torquing the gaskets beyond their recommended degree of compression, may have been a potential failure mode. SRNL recommended performing a quick compatibility test between the different process solutions used at SWPF and four different polymeric materials (the fifth one-Kalrez ® -arrived at the end of this test).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

ECAR-6588 Chemical Compatibility of MARVEL Components: Project # 33526

This ECAR serves to demonstrate the compatibility of MARVEL Reactor materials in contact with the two molten metal coolants, sodium potassium eutectic and lead. Operational requirements are determined, and recommendations for material treatment or replacement are presented.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Preliminary Compatibility Assessment of Metallic Dispenser Materials for Service in Ethanol Fuel Blends

The compatibility of selected metals representative of those commonly used in dispensing systems was evaluated in an aggressive E20 formulation (CE20a) and in synthetic gasoline (Reference Fuel C) in identical testing to facilitate comparison of results. The testing was performed at modestly elevated temperature (nominally 60 C) and with constant fluid flow in an effort to accelerate potential interactions in the screening test. Based on weight change, the general corrosion of all individual coupons exposed in the vapor phase above Reference Fuel C and CE20a as well as all coupons immersed in Reference Fuel C was essentially nil (<0.3 {micro}m/y), with no evidence of localized corrosion such as pitting/crevice corrosion or selective leaching at any location. Modest discoloration was observed on the copper-based alloys (cartridge brass and phosphor bronze), but the associated corrosion films were quite thin and apparently protective. For coupons immersed in CE20a, four different materials exhibited net weight loss over the entire course of the experiment: cartridge brass, phosphor bronze, galvanized steel, and terne-plated steel. None of these exhibited substantial incompatibility with the test fluid, with the largest general corrosion rate calculated from coupon weight loss to be approximately 4 {micro}m/y for the cartridge brass specimens. Selective leaching of zinc (from brass) and tin (from bronze) was observed, as well as the presence of sulfide surface films rich in these elements, suggesting the importance of the role of sulfuric acid in the CE20a formulation. Analysis of weight loss data for the slightly corroded metals indicated that the corrosivity of the test environment decreased with exposure time for brass and bronze and increased for galvanized and terne-plated steel. Other materials immersed in CE20a - type 1020 mild steel, type 1100 aluminum, type 201 nickel, and type 304 stainless steel - each appeared essentially immune to corrosion at the test conditions.

02 PETROLEUM↗

Compatibility of Components in Complex Systems

The quality of systems constructed from components that have been produced at enterprises in different locations is considered. A particular sequence of processes is required in order to improve the performance of enterprises involved in the design and production of such systems. That sequence is identified. The basic principles that ensure the quality of such systems are formulated: in particular, compatibility of the components is essential. The constraints associated with the system’s emergent properties must be taken into account.

42 ENGINEERING↗

Study of Material Compatibility for a Thermal Energy Storage System with Phase Change Material

The suitability of stainless steel 316L and Inconel 625 for use in a latent heat thermal energy storage (TES) system was investigated. A NaCl–NaF eutectic mixture with a melting temperature of 680 °C was used as the phase change material (PCM). Containers were filled with the PCM prior to heating to 750 °C, then examined after 100 and 2500 h of high-temperature exposure by analyzing the material surface and cross-section areas. A small amount of corrosion was present in both samples after 100 h. Neither sample suffered significant damage after 2500 h. The undesirable inter-granular grain boundary attack found in SS316L samples was in the order of 1–2 µm in depth. On Inconel 625 sample surface, an oxide complex formed, resisting material dissolution into the PCM. The surface morphology of tested samples remained largely unchanged after 2500 h, but the corrosion pattern changed from an initially localized corrosion penetration to a more uniform type. After 2500 h, the corrosion depth of Inconel 625 remained at roughly 1–2 µm, indicating that the corrosion rate decelerated. Both materials demonstrated good compatibility with the chosen NaF–NaCl eutectic salt, but the low corrosion activity in Inconel 625 samples shows a performance advantage for long term operation.

25 ENERGY STORAGE↗

Rapid Screening of Liquid Metal Wetting for a Materials Compatibility Library

Wetting behavior of molten metals on solid substrates is a critical phenomenon influencing numerous industrial applications, including welding, anti-corrosion coatings, and metal additive manufacturing (AM). In particular, molten metal jetting (MMJ), an emerging AM technology, requires that the molten metal remain pinned at the nozzle exit. Thus, each new metal requires a specific nozzle material to ensure consistent droplet ejection and deposition, making it important to rapidly identify the appropriate wetting combinations. However, traditional measurements of wetting angles require expensive equipment and only allow one combination of materials to be investigated at a time which can be time consuming. This work introduces a rapid screening method based on sessile droplet experiments to evaluate wetting profiles across multiple metal–substrate combinations simultaneously. This study investigates the wetting interactions of molten Al alloy (Al4008), Cu, and Sn on various ceramic and metal substrates to identify optimal material combinations for MMJ nozzle designs. Results demonstrate that Al4008 achieves wetting on ceramic substrates such as AlN, TiO 2 , and SiC, with varying mechanisms including chemical reactions and weak surface interactions. Additionally, theoretical predictions regarding miscibility gaps and melting point differences were verified for Cu and Sn on refractory metals like Mo and W. Findings from this study contribute to the establishment of a materials compatibility library, enabling the selection of wetting/non-wetting combinations for stable MMJ operation. This resource not only advances MMJ technologies but also provides valuable insights for broader applications such as welding, coating, and printed electronics.

Materials science↗

Extravehicular Activity and Human Surface Mobility Program (EHP) Exploration EVA (xEVA) System Compatibility Standards

Extravehicular Activity (EVA) is a significant capability for Artemis Systems which includes Gateway Program (modules), Human Landing System (HLS) Program (Integrated Lander and Human Class Delivery Lander), Lunar Terrain Vehicle (LTV), Pressurized Rover (PR), Payloads, and any other future lunar surface assets that will be utilized for exploration or science. The EVA and Human Surface Mobility Program (EHP) will provide the following: Exploration EVA (xEVA) suits, xEVA tools and crew aids along with vehicle integration/support hardware, LTV, and PR. Being a distributed and dynamic capability (moving components), xEVA System hardware will interface with almost all elements of the Artemis architecture. As such, it is important to document a singular set of EVA compatibility standards at the programmatic level to articulate “how to interface with xEVA suit hardware” and “how to design hardware that EVA crewmembers will access and manipulate.”

Exploration↗

Space Suit Material Compatibility with Space Vehicle Coolant PMS-1.5R

During a survey of 82P on February 11, 2023, a shiny substance was detected on the Progress vehicle. The suspected material was PMS-1.5R, a low volatility silicone oil coolant used in the vehicle. Crew exposure to the coolant was a concern as the low volatility would increase residence time, the time a material will stay on a surface after exposure to vacuum. A review of space suit materials revealed several materials with compatibility concerns that could impact Extravehicular Activity (EVA) operations and safety. To understand the risk, space suit materials were exposed to a simulant and tested. This testing provided the basis for rationale generated to continue with EVA operations for US EVA 86 on April 2, 2023. This testing also served as the basis to assess impacts to ISS EMU hardware due to potential contamination brought inside ISS on Russian space suits during RS EVA 61 on October 25, 2023, following an ISS Russian Multipurpose Lab Module (MLM) radiator leak of the same fluid on October 9, 2023. This paper will discuss the testing performed and analyze test results impacts to EVA operations. Additional work was conducted to determine coolant evaporation rates in space vacuum and demonstrate that no significant unreacted coolant from the MLM leak would remain on ISS surfaces long enough to contaminate the EMU or affect the ISS ECLSS water separator.

Space Suit Materials↗

LASER ENGINEERED NET SHAPING FOR REPAIR AND HYDROGEN COMPATIBILITY

A method to repair mismatched or damaged components using Laser Engineered Net Shaping{sup R} (LENS) technology to apply material was investigated for its feasibility for components exposed to hydrogen. The mechanical properties of LENS bulk materials were also tested for hydrogen compatibility. The LENS process was used to repair simulated and actual mismachined components. These sample components were hydrogen charged and burst tested in the as-received, as-damaged, and as-repaired conditions. The testing showed that there was no apparent additional deficiency associated with hydrogen charging compared to the repair technique. The repair techniques resulted in some components meeting the requirements while others did not. Additional procedure/process development is required prior to recommending production use of LENS.

08 HYDROGEN↗

Materials compatibility.

Objectives are to enable development and implementation of codes and standards for H{sub 2} containment components: (1) Evaluate data on mechanical properties of materials in H{sub 2} gas - Technical Reference on Hydrogen Compatibility of Materials; (2) Generate new benchmark data on high-priority materials - Pressure vessel steels, stainless steels; and (3) Establish procedures for reliable materials testing - Sustained-load cracking, fatigue crack propagation. Summary of this presentation are: (1) Completed measurement of cracking thresholds (K{sub TH}) for Ni-Cr-Mo pressure vessel steels in high-pressure H{sub 2} gas - K{sub TH} measurements required in ASME Article KD-10 (2) Crack arrest test methods appear to yield non-conservative results compared to crack initiation test methods - (a) Proposal to insert crack initiation test methods in Article KD-10 will be presented to ASME Project Team on Hydrogen Tanks, and (b) Crack initiation methods require test apparatus designed for dynamic loading of specimens in H{sub 2} gas; and (3) Demonstrated ability to measure fatigue crack growth of pressure vessel steels in high-pressure H{sub 2} gas - (a) Fatigue crack growth data in H{sub 2} required in ASME Article KD-10, and (b) Test apparatus is one of few in U.S. or abroad for measuring fatigue crack growth in >100 MPa H{sub 2} gas.

08 HYDROGEN↗

Elastomer and Plastic Compatibility with a Pyrolysis-Derived Bio-Oil

The compatibility of fueling infrastructure elastomers and plastics in bio-oil and diesel fuel was determined by measuring the volume swell. The bio-oil was produced via fast pyrolysis of woody feedstocks. The elastomer materials included fluorocarbons, acrylonitrile butadiene rubbers, neoprene, polyurethane, neoprene, styrene butadiene (SBR) and silicone. The plastic materials included polyphenylene sulfide (PPS), polyethylene terephthalate (PET), polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), polyoxymethylene (POM), POM copolymer, high density polyethylene (HDPE), polybutylene terephthalate (PBT), polypropylene (PP), polyethylene terephthalate glycol (PETG), polythiourea (PTU), four nylon grades, and four thermosetting resins. The majority of the elastomer and plastic materials exhibited higher volume expansion in bio-oil than in diesel. These elastomers and plastics had high polarity values which more closely align with the polarities of the bio-oil versus the diesel fuel. Conversely, SBR, silicone, HDPE, and PP are relatively nonpolar and this matches the low polarity of the diesel fuel, which resulted in higher volume expansion in diesel, rather than the bio-oil for these four polymers.

09 BIOMASS FUELS↗

A Sealed, UHV Compatible, Soft X-ray Detector Utilizing Gas Electron Multipliers

An advanced soft X-ray detector has been designed and fabricated for use in synchrotron experiments that utilize X-ray absorption spectroscopy in the study a wide range of materials properties. Fluorescence X-rays, in particular C{sub K} at 277eV, are converted in a low pressure gas medium, and charge multiplication occurs in two gas electron multipliers, fabricated in-house from glass reinforced laminate, to enable single photon counting. The detector satisfies a number of demanding characteristics often required in synchrotron environments, such as UHV compatibility compactness, long-term stability, and energy resolving capability.

43 PARTICLE ACCELERATORS↗

Sequential Deposition of Organic Films with Eco‐Compatible Solvents Improves Performance and Enables Over 12%‐Efficiency Nonfullerene Solar Cells

Abstract Casting of a donor:acceptor bulk‐heterojunction structure from a single ink has been the predominant fabrication method of organic photovoltaics (OPVs). Despite the success of such bulk heterojunctions, the task ofcontrolling the microstructure in a single casting process has been arduous and alternative approaches are desired. To achieve OPVs with a desirable microstructure, a facile and eco‐compatible sequential deposition approach is demonstrated for polymer/small‐molecule pairs. Using a nominally amorphous polymer as the model material, the profound influence of casting solvent is shown on the molecular ordering of the film, and thus the device performance and mesoscale morphology of sequentially deposited OPVs can be tuned. Static and in situ X‐ray scattering indicate that applying (R)‐(+)‐limonene is able to greatly promote the molecular order of weakly crystalline polymers and form the largest domain spacing exclusively, which correlates well with the best efficiency of 12.5% in sequentially deposited devices. The sequentially cast device generally outperforms its control device based on traditional single‐ink bulk‐heterojunction structure. More crucially, a simple polymer:solvent interaction parameter χ is positively correlated with domain spacing in these sequentially deposited devices. These findings shed light on innovative approaches to rationally create environmentally friendly and highly efficient electronics.

Ye, Long↗

High Miscibility Compatible with Ordered Molecular Packing Enables an Excellent Efficiency of 16.2% in All-Small-Molecule Organic Solar Cells

In all-small-molecule organic solar cells (ASM-OSCs), a high short-circuit current (Jsc) usually needs a small phase separation, while a high fill factor (FF) is generally realized in a highly ordered packing system. However, small domain and ordered packing always conflicted each other in ASM-OSCs, leading to a mutually restricted J sc and FF. Here, in this study, alleviation of the previous dilemma by the strategy of obtaining simultaneous good miscibility and ordered packing through modulating homo- and heteromolecular interactions is proposed. By moving the alkyl-thiolation side chains from the para- to the meta-position in the small-molecule donor, the surface tension and molecular planarity are synchronously enhanced, resulting in compatible properties of good miscibility with acceptor BTP-eC9 and strong self-assembly ability. As a result, an optimized morphology with multi-length-scale domains and highly ordered packing is realized. The device exhibits a long carrier lifetime (39.8 μs) and fast charge collection (15.5 ns). A record efficiency of 16.2% with a high FF of 75.6% and a J sc of 25.4 mA cm –2 in the ASM-OSCs is obtained. These results demonstrate that the strategy of simultaneously obtaining good miscibility with high crystallinity could be an efficient photovoltaic material design principle for high-performance ASM-OSCs.

14 SOLAR ENERGY↗

Topological Antiferromagnetic Van der Waals Phase in Topological Insulator/Ferromagnet Heterostructures Synthesized by a CMOS-Compatible Sputtering Technique

Breaking time-reversal symmetry by introducing magnetic order, thereby opening a gap in the topological surface state bands, is essential for realizing useful topological properties such as the quantum anomalous Hall and axion insulator states. In this work, a novel topological antiferromagnetic (AFM) phase is created at the interface of a sputtered, c-axis-oriented, topological insulator/ferromagnet heterostructure—Bi 2 Te 3 /Ni 80 Fe 20 because of diffusion of Ni in Bi 2 Te 3 (Ni-Bi 2 Te 3 ). The AFM property of the Ni-Bi2Te3 interfacial layer is established by observation of spontaneous exchange bias in the magnetic hysteresis loop and compensated moments in the depth profile of the magnetization using polarized neutron reflectometry. Analysis of the structural and chemical properties of the Ni-Bi2Te3 layer is carried out using selected-area electron diffraction, electron energy loss spectroscopy, and X-ray photoelectron spectroscopy. These studies, in parallel with first-principles calculations, indicate a solid-state chemical reaction that leads to the formation of Ni=Te bonds and the presence of topological antiferromagnetic (AFM) compound NiBi 2 Te 4 in the Ni-Bi 2 Te 3 interface layer. The Neél temperature of the Ni-Bi 2 Te 3 layer is ≈ 63 K, which is higher than that of typical magnetic topological insulators (MTIs). The presented results provide a pathway toward industrial complementary metal-oxide-semiconductor (CMOS)-process-compatible sputtered-MTI heterostructures, leading to novel materials for topological quantum devices.

36 MATERIALS SCIENCE↗

High‐Performance Ternary Organic Solar Cells with Enhanced Luminescence Efficiency and Miscibility Enabled by Two Compatible Acceptors

Abstract The ternary strategy has proven to be an effective method for improving the efficiency of organic solar cells (OSCs). However, designing and selecting the third component still pose challenges. In this study, this issue is addressed by focusing on the PBDB‐T:Y18‐F binary system and introducing a new, strong luminescent, asymmetric small‐molecule acceptor (SMA) called L8‐CBIC‐Cl, which shares a similar skeleton with Y18‐F. The similarity in molecular framework facilitates good compatibility between the two acceptors, resulting in the formation of an alloy‐like acceptor phase. Furthermore, the norbornenyl‐modified end group in L8‐CBIC‐Cl contributes to its strong luminescent properties, which in turn leads to a low non‐radiative energy loss and a high open‐circuit voltage. Consequently, the PBDB‐T:L8‐CBIC‐Cl:Y18‐F based ternary devices realize a high power conversion efficiency (PCE) up to 17.01%, which is higher than PBDB‐T:Y18‐F device (14.49%). Importantly, L8‐CBIC‐Cl exhibits a good universality as a guest acceptor in other three binary systems (D18:Y6, D18:BTP‐eC9‐4F, and D18:L8‐BO). The D18:L8‐BO:L8‐CBIC‐Cl device shows an impressive efficiency of 19%. The work demonstrates that employing SMA with a high PLQY and better miscibility with host acceptor as the third component has a great potential for developing high‐efficiency ternary OSCs.

Chemistry↗