Search NASA⌕ Search

SEARCH · Search NASA

Results for “Crystalline solids”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Solid-state rigid-rod polymer composite electrolytes with nanocrystalline lithium ion pathways

A critical challenge for next-generation lithium-based batteries lies in development of electrolytes that enable thermal safety along with use of high-energy-density electrodes. We describe molecular ionic composite (MIC) electrolytes based on an aligned liquid crystalline polymer combined with ionic liquids and concentrated Li salt. This high strength (200 MPa) and non-flammable solid electrolyte possesses outstanding Li + conductivity (1 mS cm -1 at 25 °C) and electrochemical stability (5.6 V vs Li|Li + ) while suppressing dendrite growth and exhibiting low interfacial resistance (32 Ω cm 2 ) and overpotentials (≤ 120 mV @ 1 mA cm -2 ) during Li symmetric cell cycling. A heterogeneous salt doping process modifies a locally ordered polymer-ion assembly to incorporate an inter-grain network filled with defective LiFSI & LiBF 4 nanocrystals, strongly enhancing Li + conduction. Furthermore, this modular material fabrication platform shows promise for safe and high-energy-density energy storage and conversion applications, incorporating the fast transport of ceramic-like conductors with the superior flexibility of polymer electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2025

Experimental evidence of disordered crystalline premixing in sputter-deposited Ni(V)/Al multilayers

The sputter deposition of alternating layers of Ni(V) and Al forms a reactive multilayer known to undergo self-propagating formation reactions when ignited. The sequential deposition process leads to nanometer-scale premixing of reactants at each included interface, which ultimately affects multilayer exothermicity. This work performs the direct measurement of a disordered face-centered cubic (FCC) solid solution premixed phase at the interfaces of Ni(V)/Al multilayers via scanning transmission electron microscopy. The crystallinity of the observed phase differs from previously reported a priori predictions of an amorphous interlayer. The disordered FCC phase retains its symmetry after annealing for 16 h at 135 ± 5 °C, but the lattice parameter shifts consistently with an Al-rich composition. The existence of a crystalline premix in Ni(V)/Al is attributed to the electronic contribution to the entropy of crystallization. The importance of electronic entropy to the phase formation of energetic materials motivates its inclusion when constructing digital twins for atomistic kinetics and ignition sensitivity.

Crystal structure↗
DOE OSTI2026

Surface-Functionalized, Two-Dimensional Polymer Electrochromic Layers as Ultrafast, Multi-State Infrared Optical Gates

Electrochromic devices have widespread application potential, but the currently available switching speeds limit broad real-world implementation of this technology. Here, we report surface-engineered two-dimensional polymers with ionophilic pores that offer unprecedented switching speeds in solid-state, two-terminal, electrochromic devices. In particular, we demonstrate that a crystalline donor–acceptor 2DP functionalized with ethylene glycol oligomers exhibits multistate infrared absorption that is 4× faster (t c = 320 ms) with 3× coloration efficiency (491 cm 2 C –1 ) compared to an alkyl functionalized 2DP constructed from the same chromophores. The functionalized nanoporous surfaces enable rapid switching in these materials under either oxidative or reductive conditions, allowing us to access a range of robust, stable optical responses in a single electrochromic layer. These attributes led us to leverage surface-functionalized 2DPs as multistate infrared logic gates. Collectively, this work demonstrates that surface engineering of nanoporous crystalline lattices is a promising approach to co-optimize the electronic and ionic conductivities required to achieve rapidly switchable electrochromic layers. Beyond speed and efficiency, the demonstration of multistate infrared characteristics shows that electrochromic frameworks are useful in integrated optoelectronic circuits. This positions surface-engineered 2DPs as improved electrochromic coatings and a new material platform for photonic information processing and adaptive devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Shear wave propagation in a liquid crystal: An inelastic X-ray scattering study

For this work, we investigated the spectrum of density fluctuations of a liquid crystal, CB7CB, in two different orientations by using high-resolution inelastic x-ray scattering. Our analysis, based on Bayesian principles, revealed that high-frequency collective excitations propagate through this mesoscale-ordered sample in a peculiar manner that lies somewhere between those observed in liquids and crystalline systems. Interestingly, when we probed longer length scales, a more pronounced solid-like response emerged. This was mainly characterized by anomalously sharp inelastic excitations and the onset of shear mode propagation. Comparison with previous x-ray diffraction results suggests a correlation between the observed behavior and the mesogen arrangement.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Comparative Study on the Pretreatment of Aspen and Maple With 1-Ethyl-3-methylimidazolium Acetate and Cholinium Lysinate

The efficiency of the enzymatic digestibility of certain lignocellulosic biomass has been observed as a function of their structural and chemical changes which in turn depends on the ionic liquid (IL) used as the pretreatment solvent. This study demonstrated and compared the feasibility of the IL pretreatment process for two woody biomasses, namely maple and aspen, using two mechanistically distinct ILs, i.e., 1-ethyl-3-methylimidazolium acetate (C 2 mim][OAc]) and cholinium lysinate ([Ch][Lys]) as the solvent. The pretreatment was performed at three different temperatures of 100°C, 140°C, and 160°C at a high solid loading of 25 wt% to understand the impact of lignin content and crystallinity index on enzymatic digestibility. Saccharification of the biomass obtained after the IL pretreatment afforded 30–85% glucan conversions. For aspen, both [C 2 mim][OAc] and [Ch][Lys] exhibited the highest glucan conversion at 140°C. For maple, the highest glucan conversion was obtained at 140°C with [C 2 mim][OAc], whereas [Ch][Lys] had an optimum glucan conversion at 160°C. These pretreatments resulted in negligible delignification irrespective of the IL used. A significant loss of crystallinity was observed for all [C 2 mim][OAc]-pretreated biomasses, whereas the pretreatment with [Ch][Lys] resulted in an increase in the crystallinity index.

Choudhary, Hemant↗
DOE OSTI2024

Non-covalent planarizing interactions yield highly ordered and thermotropic liquid crystalline conjugated polymers

Controlling the multi-level assembly and morphological properties of conjugated polymers through structural manipulation has contributed significantly to the advancement of organic electronics. In this work, a redox active conjugated polymer, TPT–TT, composed of alternating 1,4-(2-thienyl)-2,5-dialkoxyphenylene (TPT) and thienothiophene (TT) units is reported with non-covalent intramolecular S⋯O and S⋯H–C interactions that induce controlled main-chain planarity and solid-state order. As confirmed by density functional theory (DFT) calculations, these intramolecular interactions influence the main chain conformation, promoting backbone planarization, while still allowing dihedral rotations at higher kinetic energies (higher temperature), and give rise to temperature-dependent aggregation properties. Thermotropic liquid crystalline (LC) behavior is confirmed by cross-polarized optical microscopy (CPOM) and closely correlated with multiple thermal transitions observed by differential scanning calorimetry (DSC). This LC behavior allows us to develop and utilize a thermal annealing treatment that results in thin films with notable long-range order, as shown by grazing-incidence X-ray diffraction (GIXD). Specifically, we identified a first LC phase, ranging from 218 °C to 107 °C, as a nematic phase featuring preferential face-on π–π stacking and edge-on lamellar stacking exhibiting a large extent of disorder and broad orientation distribution. A second LC phase is observed from 107 °C to 48 °C, as a smectic A phase featuring sharp, highly ordered out-of-plane lamellar stacking features and sharp tilted backbone stacking peaks, while the structure of a third LC phase with a transition at 48 °C remains unclear, but resembles that of the solid state at ambient temperature. Furthermore, the significance of thermal annealing is evident in the ∼3-fold enhancement of the electrical conductivity of ferric tosylate-doped annealed films reaching 55 S cm −1 . More importantly, thermally annealed TPT–TT films exhibit both a narrow distribution of charge-carrier mobilities (1.4 ± 0.1) × 10 −2 cm 2 V −1 s −1 along with a remarkable device yield of 100% in an organic field-effect transistor (OFET) configuration. This molecular design approach to obtain highly ordered conjugated polymers in the solid state affords a deeper understanding of how intramolecular interactions and repeat-unit symmetry impact liquid crystallinity, solution aggregation, solution to solid-state transformation, solid-state morphology, and ultimately device applications.

Chemistry↗
DOE OSTI2021

Safely probing the chemistry of Chernobyl nuclear fuel using micro-focus X-ray analysis

Detailed chemical analysis of the solidified molten fuel still residing in the stricken Chernobyl reactor unit 4 are inferred using multi-modal micro-focus X-ray analysis of a low-radioactivity proxy. A fascinating mixture of molten UO 2 , nuclear fuel cladding, concrete, stainless steel and other nuclear reactor components, these materials behaved like lava, solidifying to form a complex, highly radioactive glass-ceramic. Using element-specific chemical probes (micro-X-ray fluorescence and X-ray absorption spectroscopy), coupled with micro-diffraction analysis, the crystalline phase assemblage of simulants of these heterogeneous materials was established, which included “chernobylite” and a range of compositions in the (U 1-x Zr x )O 2 solid solution. Novel insight to nuclear accident fuel chemistry was obtained by establishing the oxidation state and local coordination of uranium not only in these crystalline phases, but uniquely in the amorphous fraction of the material, which varied depending on the history of the nuclear lava as it flowed through the reactor. This study demonstrates that micro-focus X-ray analysis of very small fractions of material can yield rich chemical information, which can be applied to nuclear-melt down materials to aid decommissioning and nuclear fuel management at nuclear accident sites.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Discovery of a Stripe Phase in an Elemental Solid

Translational symmetry breaking is foundational to condensed matter physics because it is associated with crystal formation. At much lower energy scales, the breaking of crystalline translational symmetry can be driven by electronic, rather than ionic, degrees of freedom and may give rise to stripe order, a unidirectional ordered state. Such symmetry breaking has been seen in two-dimensional and strongly correlated systems. Here, for the first time, we report the observation of stripe order in an elemental solid, tellurium. Through topographic and spectroscopic imaging, we discover a commensurate 4 × 1 stripe phase. Surprisingly, this exotic order is so robust that it survives close to room temperature. Notably, our diffraction experiments confirm the bulk nature of the stripe order, showing the minuteness of potential lattice distortion associated with the order. In conclusion, our discovery of the stripe order in tellurium opens new windows to understanding the spontaneous symmetry breaking in elemental solids.

charge order↗
DOE OSTI2020

Modified Isotherm Modeling to Predict Cs Exchange with Crystalline Silicotitanate in Tank Waste Simulants

The U.S. Department of Energy is working to expedite processing of Hanford tank waste supernate at the Hanford Waste Treatment and Immobilization Plant. To support this goal, Washington River Protection Solutions is designing a Tank Side Cesium Removal (TSCR) system for suspended solids and cesium (Cs/ 137 Cs) removal from Hanford tank waste supernate. The ion exchange media selected for Cs removal at TSCR is crystalline silicotitanate (CST) that is manufactured in a nearly spherical form by Honeywell UOP LLC (UOP; Des Plaines, IL) as product IONSIV® R9140-B (Na form). The Zheng Anthony Miller (ZAM) isotherm model (Zheng et al. 1997) is a multicomponent ion exchange model used to predict the exchange of Group I metals onto CST. The ZAM isotherm has historically been used to predict Cs distribution values from Hanford and Savannah River Site (SRS) tank waste simulants. Figure S.1 summarizes model predictions from the ZAM isotherm that indicate poor prediction of Cs distribution values for simple and complex simulants with the engineered form of CST, IONSIV® R9140-B, and IONSIV® R9120-B where the solid line indicates a perfect fit by the model. The dotted lines indicate ±20% error. Batch contact testing with Hanford tank waste complex and simple simulants was used in conjunction with SRS simulants to experimentally determine Cs distribution values using a modification to the original isotherm model. The experimentally determined maximum Cs capacity for IONSIV® R9140-B CST in both the simple and complex matrices was found to be 0.53±0.3 mmoles Cs/g of CST. This value is not drastically different from the maximum Cs capacity of 0.58 mmoles Cs/g TAM-5 reported by Zheng et al. (1997). However, it is important to note that TAM-5 (commercially IONSIV® IE-910) is a powder. Hamm et al. (2002) determined that a dilution factor was needed to account for the Zr(OH)2 binder in the engineered form of CST. Hamm et al. determined that a dilution factor of 0.68 was appropriate to account for binder contribution and correct overprediction of Cs exchange on the engineered form of CST in ZAM calculations. This reduced the total capacity from 0.58 mmol/g with TAM-5 to 0.39 mmol/g for the engineered form of CST (Hamm et al. 2002). Despite substituting the experimentally determined maximum Cs capacity of 0.55 mmoles Cs/g for the literature-reported capacity of 0.39 mmoles Cs/g, it was determined that additional modifications to the model’s equilibrium rate constants were necessary in refining the isotherm model. The modified model overpredicted K+ uptake by the CST when compared to digested CST results described by Campbell et al. (2019). The modified model was further revised to omit three of the five K+ exchange equilibrium reactions described by ZAM to reduce the additional K+ loading seen by the model. Figure S.2 summarizes the revised model isotherm predictions plotted against measured Kd values.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Excited States of Crystalline Point Defects with Multireference Density Matrix Embedding Theory

Accurate and affordable methods to characterize the electronic structure of solids are important for targeted materials design. Embedding-based methods provide an appealing balance in the trade-off between cost and accuracy-particularly when studying localized phenomena. Here, we use the density matrix embedding theory (DMET) algorithm to study the electronic excitations in solid-state defects with a restricted open-shell Hartree-Fock (ROHF) bath and multireference impurity solvers, specifically, complete active space self-consistent field (CASSCF) and n-electron valence state second-order perturbation theory (NEVPT2). In this work, we apply the method to investigate the electronic excitations in an oxygen vacancy (OV) on a MgO(100) surface and find absolute deviations within 0.05 eV between DMET using the CASSCF/NEVPT2 solver, denoted as CAS-DMET/NEVPT2-DMET, and the nonembedded CASSCF/NEVPT2 approach. Next, we establish the practicality of DMET by extending it to larger supercells for the OV defect and a neutral silicon vacancy in diamond where the use of nonembedded CASSCF/NEVPT2 is extremely expensive.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Computational Elucidation of Mechanical Degradation in NMC Cathodes: Impact on Cell Performance

Next-generation lithium ion batteries are expected to demonstrate superior energy and power density with longer cycle life for successful electrification of the automobile, aviation, and marine industries. Adoption of lithium metal anodes with solid electrolytes can help to achieve that goal given that the dendrite-related issues are solved eventually. Another possibility is to use Ni-rich high-capacity NMC cathode materials with liquid and/or solid electrolytes, which presently experiences rapid capacity fade while charged to higher voltages. Several mechanical and chemical degradation mechanisms are active within these NMC-based cathode particles. Recent experimental research activities attempted to correlate the mechanical damage with the capacity fade experienced by Ni-rich LiNi x Mn y Co z O 2 (x+y+z = 1) (NMC) cathodes. Here, a computational framework is developed in this study capable of quantifying the evolution of inter primary particle and cathode/electrolyte interfacial fracture experienced by the poly- and single-crystalline NMC cathodes during charge/discharge operation. Influences of mechanical degradation on the overall cell capacity, while operating with liquid and/or solid electrolytes, are successfully characterized. Decreasing the size of the cathode primary particles, or the size of the single-crystalline cathodes, can mitigate the overall mechanical degradation, and subsequent capacity fade, experienced by NMC cathodes. The developed theoretical methodology can help the engineers and scientists to better understand the mechanical degradation mechanism prevalent in Ni-rich NMC cathodes and build superior lithium ion-based energy storage devices for the application in next-generation devices.

25 ENERGY STORAGE↗
DOE OSTI2024

Sucrose‐Based Dense, Pure, and Highly‐Crystalline Graphitic Materials for Lithium‐Ion Batteries

At present, most synthetic graphite materials commonly used as anode active ingredients in lithium-ion cells are produced by graphitization of petroleum cokes. The carbon footprint associated with synthetic graphite production is significant. Thus, bio-derived and cheap precursors, such as saccharides, would be an attractive alternative for the sustainable production of graphitic carbons. However, they are non-graphitizing at temperatures as high as 3000 °C, preserving the curved, fullerene-like structure of graphene layers and microporosity. Consequently, many lithium ions are consumed during the formation of solid electrolyte interphase films and passivated in the nanovoids. Here, a method for the production of pure, crystalline, graphitic materials based on sucrose disposed of microporosity is presented, which also works with a variety of saccharides and other organic precursors of hard carbons—generally considered incapable of such transformation. This process employs catalytic graphitization by Si particles at high temperatures. Finally, the electrochemical response of such derived sucrose-based graphite in Li-ion half-cells demonstrated its feasibility to serve as an anode active material for rechargeable Li-ion batteries.

Si particles↗
DOE OSTI2020

Heterolytic Scission of Hydrogen Within a Crystalline Frustrated Lewis Pair

We report the heterolysis of molecular hydrogen under ambient conditions by the crystalline frustrated Lewis pair (FLP) 1-{2-[bis(pentafluorophenyl)boryl]phenyl}-2,2,6,6-tetramethylpiperidine (KCAT). The gas–solid reaction provides an approach to prepare the solvent-free, polycrystalline ion pair KCATH2 through a single crystal to single crystal transformation. The crystal lattice of KCATH2 increases in size relative to the parent KCAT by approximately 2%. Microscopy was used to follow the transformation of the highly colored red/orange KCAT to the colorless KCATH2 over a period of 2 h at 300 K under a flow of H2 gas. There is no evidence of crystal decrepitation during hydrogen uptake. Inelastic neutron scattering employed over a temperature range from 4–200 K did not provide evidence for the formation of polarized H2 in a precursor complex within the crystal at low temperatures and high pressures. However, at 300 K, the INS spectrum of KCAT transformed to the INS spectrum of KCATH2. Calculations suggest that the driving force is more favorable in the solid state compared to the solution or gas phase, but the addition of H2 into the KCAT crystal is unfavorable. Ab Initio methods were used to calculate the INS spectra of KCAT, KCATH2, and a possible precursor complex of H2 in the pocket between the B and N of crystalline KCAT. Ex-situ NMR showed that the transformation from KCAT to KCATH2 is quantitative and our results suggest that the hydrogen heterolysis process occurs via H2 diffusion into the FLP crystal with a rate-limiting movement of H2 from inactive positions to reactive sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High entropy alloys with hexagonal close-packed structure derived from thin film combinatorial approach

A thin film combinatorial synthesis approach was utilized to develop a compositional and structural library for the OsRuWCo alloy system. The survey of this alloy space produced 24 unique compositions and their corresponding crystal structures, which represent a phase map where amorphous and single-phase hexagonal close-packed alloys were identified. Based on the identification of a promising candidate film region, a new high entropy alloy based on OsRuWCo, but with non-equiatomic composition, was synthesized in bulk form. The alloy exhibited a single-phase hexagonal close-packed structure in the as-cast state. Three derivatives from this system were also developed by considering the heat of mixing, atomic size, and binary solubility. These new alloys are based on OsRuWCoIr and OsRuWCoFe, both of which exhibit single-phase hexagonal close-packed as-cast structures, as determined by X-ray diffraction and electron microscopy. Additionally, this large compositional space was utilized to evaluate conventional parameters that describe high entropy alloys (ΔS mix , ΔH mix , Ω, δ, and VEC), and these were found to elucidate the criteria for solid solution formation in this system. Additionally, trends illustrating the evolution from amorphous to crystalline phases are demonstrated and discussed. It is concluded that in this particular case, the dominant factors promoting crystallinity are thermodynamic or electronic, rather than geometric.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Trajectory sampling and finite-size effects in first-principles stopping power calculations

Abstract Real-time time-dependent density functional theory (TDDFT) is presently the most accurate available method for computing electronic stopping powers from first principles. However, obtaining application-relevant results often involves either costly averages over multiple calculations or ad hoc selection of a representative ion trajectory. We consider a broadly applicable, quantitative metric for evaluating and optimizing trajectories in this context. This methodology enables rigorous analysis of the failure modes of various common trajectory choices in crystalline materials. Although randomly selecting trajectories is common practice in stopping power calculations in solids, we show that nearly 30% of random trajectories in an FCC aluminum crystal will not representatively sample the material over the time and length scales feasibly simulated with TDDFT, and unrepresentative choices incur errors of up to 60%. We also show that finite-size effects depend on ion trajectory via “ouroboros” effects beyond the prevailing plasmon-based interpretation, and we propose a cost-reducing scheme to obtain converged results even when expensive core-electron contributions preclude large supercells. This work helps to mitigate poorly controlled approximations in first-principles stopping power calculations, allowing 1–2 order of magnitude cost reductions for obtaining representatively averaged and converged results.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Measuring the density, viscosity, and surface tension of molten titanates using electrostatic levitation in microgravity

Rare earth and barium titanates are useful as ferroelectric, dielectric, and optical materials. Measurements of their thermophysical properties in the liquid state can help guide melt processing technologies for their manufacture and advance understanding of fragile liquids' behavior and glass formation. Here, we report the density, thermal expansion, viscosity, and surface tension of molten BaTi 2 O 5 , BaTi 4 O 9 , and 83TiO 2 -17RE 2 O 3 (RE = La or Nd). Measurements were made using electrostatic levitation and droplet oscillation techniques in microgravity, which provide access to quiescent liquid droplets and deep supercooling of 510–815 K below the equilibrium melting points. Densities were measured over 900–2400 K. Viscosities were similar for all four compositions, increasing from ~10 mPa s near 2100 K to ~30 mPa s near 1750 K. Surface tensions were 450–490 dyn cm -1 for the rare earth titanates and 383–395 dyn cm -1 for the barium titanates; surface tensions of all compositions had small or negligible temperature dependence over 1700–2200 K. In conclusion, for solids recovered after melt quenching, x-ray microtomography revealed the fracture mechanics in crystalline products and minimal internal porosity in glass products, likely arising from entrapped gas bubbles. Internal microstructures were generally similar for products processed either in microgravity or in a terrestrial aerodynamic levitator.

42 ENGINEERING↗
DOE OSTI2021

Solvent-Cast Solid Electrolyte Membranes Based on a Charged Rigid-Rod Polymer and Ionic Liquids

Solid-state electrolytes are attractive for use in electrochemical devices because they remove the need for a flammable liquid electrolyte while contributing to the structural integrity of the device. We have recently developed a class of solid electrolytes, termed molecular ionic composites (MICs), composed of ionic liquids (ILs) and a rigid-rod polyelectrolyte, poly(2,2'-disulfonyl-4,4'-benzidine terephthalamide) (PBDT). MIC materials, originally obtained through an ion-exchange process between IL and PBDT aqueous solution, possess an unprecedented combination of high ionic conductivity, high thermal stability, low flammability and widely tunable tensile storage moduli. Here we present a facile solvent casting method for preparing MIC membranes. These membranes are uniform, flexible, and tough, with tunable composition and thickness (≥ 40 μm). Unlike the previous ion-exchange method, which only allowed incorporation of hydrophilic ILs, we can now incorporate hydrophobic ILs to prepare MIC membranes for, e.g. battery electrolytes. A sodium (Na) metal symmetric cell constructed with a PBDT-Pyr 14 TFSI membrane as the solid electrolyte shows long-term stable cycling (> 500 h.) at 60 °C. Furthermore, the ability to prepare MICs using both hydrophilic and hydrophobic ILs initiates a wider range of MIC materials and broadens the array of applications accessible by MIC membranes.

25 ENERGY STORAGE↗