SEARCH · Search NASA

Results for “DAMPER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1972

The motion and stability of a dual spin satellite during the momentum wheel spin-up maneuver

The stability of a dual-spin satellite system during the momentum wheel spin-up maneuver is treated both analytically and numerically. The dual-spin system consists of: a slowly rotating or despun main-body; a momentum wheel (or rotor) which is accelerated by a torque motor to change its initial angular velocity relative to the main part to some high terminal value; and a nutation damper. A closed form solution for the case of a symmetrical satellite indicates that when the nutation damper is physically constrained for movement (i.e. by use of a mechanical clamp) the magnitude of the vector sum of the transverse angular velocity components remains bounded during the wheel spin-up under the influence of a constant motor torque. The analysis is extended to consider such effects as: the motion of the nutation damper during spin-up; a non-uniform motor torque; and the effect of a non-symmetrical mass distribution in the main spacecraft and the rotor. An approximate analytical solution using perturbation techniques is developed for the case of a slightly asymmetric main spacecraft.

Bainum, P. M.↗

NASA NTRS1973

The motion and stability of a dual-spin satellite during the momentum wheel spin-up maneuver.

The stability of a dual-spin satellite system during the momentum wheel spin-up maneuver is treated both analytically and numerically. The dual-spin system consists of a slowly rotating or despun main body, a momentum wheel (or rotor) which is accelerated by a torque motor to change its initial angular velocity relative to the main part to some high terminal value, and a nutation damper. A closed-form solution for the case of a symmetrical satellite indicates that when the nutation damper is physically constrained from movement (i.e., by use of a mechanical clamp) the magnitude of the vector sum of the transverse angular velocity components remains bounded during the wheel spin-up under the influence of a constant motor torque. The analysis is extended to consider such effects as the motion of the nutation damper during spin-up, and the effect of a nonsymmetrical mass distribution.

Sen, S.↗

NASA NTRS1974

Passive stabilization of the Long Duration Exposure Facility (LDEF)

The results of a study on the application of the magnetically anchored rate damper to gravity gradient stabilization of the Long Duration Exposure Facility (LDEF) are presented. The analyses and simulations required to investigate the use of an existing viscous magnetic rate damper for rate stabilizing the LDEF spacecraft were performed. The following tasks were included: linear performance estimates, capture and damper requirements, and performance prediction. Each of these tasks was performed for two gravity gradient stabilization configurations; an axisymmetric configuration for two-axis (pitch and roll) stability; and a non-axisymmetric configuration for three-axis stability. The results are presented by stabilization configuration.

Das, A.↗

NASA NTRS1977

Experimental and analytical dynamic flow characteristics of an axial-flow fan from an air cushion landing system model

An investigation was conducted to compare the steady-state and dynamic flow characteristics of an axial-flow fan which had been used previously as the air supply fan for some model air cushion landing system studies. Steady-state flow characteristics were determined in the standard manner by using differential orifice pressures for the flow regime from free flow to zero flow. In this same regime, a correlative technique was established so that fan inlet and outlet pressures could be used to measure dynamic flow as created by a rotating damper. Dynamic tests at damper frequencies up to 5 Hz showed very different flow characteristics when compared with steady-state flow, particularly with respect to peak pressures and the pressure-flow relationship at fan stall and unstall. A generalized, rational mathematical fan model was developed based on physical fan parameters and a steady-state flow characteristic. The model showed good correlation with experimental tests at damper frequencies up to 5 Hz.

Thompson, W. C.↗

NASA NTRS1977

Shock isolator for diode laser operation on a closed-cycle refrigerator

Closed-cycle helium refrigerators are widely used as coolers for semiconductor diode lasers. These refrigerators pose several difficulties including temperature oscillations due to varying refrigerator capacity during the Solvay cycle, and impact shocks delivered to the diode in the cycle's expansion phase. A shock isolator has been designed to isolate diode lasers from such impact shocks. Slow diode current scans have been made before installation of the shock isolator, with the isolator but no thermal damper, and with both devices. With the isolator and no damper, the diode output frequency oscillated at the refrigerator cycle rate, deviating by plus or minus 40 MHz. Using the isolator and the damper no frequency fluctuation was detected.

Jennings, D. E.↗

NASA NTRS1980

Development of procedures for calculating stiffness and damping of elastomers in engineering applications, part 7

An elastomer shear damper was designed, tested, and compared with the performance of the T 55 power turbine supported on the production engine roller bearing support. The Viton 70 shear damper was designed so that the elastomer damper could be interchanged with the production T 55 power turbine roller bearing support. The results show that the elastomer sheer dampener permitted stable operation of the power turbine to the maximum operating speed of 16,000 rpm.

Rieger, A.↗

NASA NTRS1981

Mechanical design handbook for elastomers

A comprehensive guide for the design of elastomer dampers for application in rotating machinery is presented. Theoretical discussions, a step by step procedure for the design of elastomer dampers, and detailed examples of actual elastomer damper applications are included. Dynamic and general physical properties of elastomers are discussed along with measurement techniques.

Darlow, M.↗

NASA NTRS1985

Analysis of an oscillatory oil squeeze film containing a central gas bubble

A squeeze-film damper, consisting of two circular plates, having only normal oscillatory relative motion is considered. The liquid lubricant between the plates is assumed to contain a single central gas bubble. The effect of the bubble on the damper performance is analyzed. Comparison is made with the performance of a pure liquid damper. Substantial deviations in peak dynamic pressures are predicted which explain discrepancies between experimental and theoretical results reported in the literature.

Haber, S.↗

NASA NTRS1992

Eigenvalue error analysis of viscously damped structures using a Ritz reduction method

The efficient solution of the eigenvalue problem that results from inserting passive dampers with variable stiffness and damping coefficients into a structure is addressed. Eigenanalysis of reduced models obtained by retaining a number of normal modes augmented with Ritz vectors corresponding to the static solutions resulting from the load patterns introduced by the dampers has been empirically shown to yield excellent approximations to the full eigenvalue problem. An analysis of this technique in the case of a single damper is presented. A priori and a posteriori error estimates are generated and tested on numerical examples. Comparison theorems with modally truncated models and a Markov parameter matching reduced-order model are derived. These theorems corroborate the heuristic that residual flexibility methods improve low-frequency approximation of the system. The analysis leads to other techniques for eigenvalue approximation. Approximate closed-form solutions are derived that include a refinement to eigenvalue derivative methods for approximation. An efficient Newton scheme is also developed. A numerical example is presented demonstrating the effectiveness of each of these methods.

Chu, Cheng-Chih↗

NASA NTRS1994

Shake test results of the MDHC test stand in the 40- by 80-foot wind tunnel

A shake test was conducted to determine the modal properties of the MDHC (McDonnell Douglas Helicopter Company) test stand installed in the 40- by 80- Foot Wind Tunnel at Ames Research Center. The shake test was conducted for three wind-tunnel balance configurations with and without balance dampers, and with the snubber engagement to lock the balance frame. A hydraulic shaker was used to apply random excitation at the rotor hub in the longitudinal and lateral directions. A GenRad 2515 computer-aided test system computed the frequency response functions at the rotor hub and support struts. From these response functions, the modal properties, including the natural frequency, damping ratio, and mode shape were calculated. The critical modes with low damping ratios are identified as the test-stand second longitudinal mode for the dampers-off configuration, the test-stand yaw mode for the dampers-on configuration, and the test stand first longitudinal mode for the balance-frame locked configuration.

Lau, Benton H.↗

NASA NTRS1994

Test results for rotordynamic coefficients of anti-swirl self-injection seals

Test results are presented for rotordynamic coefficients and leakage for three annular seals which use anti-swirl self-injection concept to yield significant improvement in whirl frequency ratios as compared to smooth and damper seals. A new anti-swirl self-inection mechanism is achieved by deliberately machining self-injection holes inside the seal stator mechanism which is used to achieve effective reduction of the tangential flow which is considered as a prime cause of rotor instability in high performance turbomachinery. Test results show that the self-injection mechanism significantly improves whirl frequency ratios; however, the leakage performance degrades due to the introduction of the self-injection mechanism. Through a series of the test program, an optimum anti-swirl self-injection seal which uses a labyrinth stator surface with anti-axial flow injections is selected to obtain a significant improvement in the whirl frequency ratio as compared to a damper seal, while showing moderate leakage performance. Best whirl frequency ratio is achieved by an anti-swirl self-injection seal of 12 holes anti-swirl and 6 degree anti-leakage injection with a labyrinth surface configuration. When compared to a damper seal, the optimum configuration outperforms the whirl frequency ratio by a factor of 2.

Kim, C. H.↗

NASA NTRS1994

Dynamics of the McDonnell-Douglas Large Scale Dynamic Rig and dynamic calibration of the rotor balance

A shake test was performed on the Large Scale Dynamic Rig in the 40- by 80-Foot Wind Tunnel in support of the McDonnell Douglas Advanced Rotor Technology (MDART) Test Program. The shake test identifies the hub modes and the dynamic calibration matrix of the rotor balance. For hub mode identification, three configurations were tested: wind tunnel scale unlocked with dampers engaged and disengaged, and wind tunnel scale locked. Test data were analyzed with a multi-degree-of-freedom time domain algorithm to identify the modal properties of the hub modes. The damping of the low frequency hub modes (ground resonance modes) increases significantly with the wind tunnel dampers engaged. For dynamic calibration of the rotor balance, the shake test was performed only with the wind tunnel dampers engaged. The dynamic calibration matrix, computed from the shake test data using a least squares error method, is used to correct the five-per-rev vibratory balance readings. The corrections are large for the side force, moderate for the axial force and inplane hub moments, and small for the normal force.

Nguyen, Khanh↗

NASA NTRS1997

Rotordynamic Instability Problems in High-Performance Turbomachinery 1996

The first rotordynamics workshop proceedings emphasized a feeling of uncertainty in predicting the stability of characteristics of high-performance turbomachinery. In the second workshop proceedings these uncertainties were reduced through programs established to systematically resolve problems, with emphasis on experimental validation of the forces that influence rotordynamics. In the third proceedings many programs for predicting or measuring forces and force coefficients in high-performance turbomachinery produced results. Data became available for designing new machines with enhanced stability characteristics or for upgrading existing machines. In the fourth proceedings there emerged trends towards a more unified view of rotordynamic instability problems and several encouraging new analytical developments. The fifth workshop supported the continuing trend toward a unified view with several new developments in the design and manufacture of new turbomachineries with enhanced stability characteristics along with new data and associated numerical/theoretical results. The sixth workshop report provided field experience and experimental results, and expanded the use of computational and control techniques with integration of damper, bearing, and eccentric seal operation results. The seventh workshop report provided field experiences, numerical, theoretical, and experimental results and control methods for seals, bearings, and dampers with some attention given to variable thermophysical properties and turbulence measurements, and introduction of two-phase flow results. In the present workshop, active magnetic bearings (AMB's) evolve into a new method of measuring rotordynamic coefficients with discussions on honeycomb seals, drop of magnetically supported rotors, seals, bearings and dampers with new data being reported. The intent of the workshop and this proceedings is to provide a continuing impetus for an understanding and resolution of these problems.

Source record↗

NASA NTRS1959

Some Effects of Yaw Damping on Airplane Motions and Vertical-Tail Loads in Turbulent Air

Results of analytical and flight studies are presented to indicate the effect of yaw damping on the airplane motions and the vertical-tail loads in rough air. The analytical studied indicate a rapid reduction in loads on the vertical tail as the damping is increased up to the point of damping the lateral motions to 1/2 amplitude in one cycle. Little reduction in load is obtained by increasing the lateral damping beyond that point. Flight measurements made in rough air at 5,000 and 35,000 feet on a large swept-wing bomber equipped with a yaw damper show that the yaw damper decreased the loads on the vertical tail by about 50 percent at 35,000 feet. The reduction in load at 5,000 feet was not nearly as great. Measurements of the pilot's ability to damp the lateral motions showed that the pilot could provide a significant amount of damping but that manual control was not as effective as a yaw damper in reducing the loads.

Funk, Jack↗

NASA NTRS2000

Blading System and Method For Controlling Structural Vibrations

A new blading system for controlling the structural vibrations in axial-flow compressors, turbines, or fans, as in aircraft engines and like turbomachines including a stator disc and a rotor disc is presented. The rotor disc defines several radial hubs that retain the rotor blading systems. Each blading system includes a blade formed of an airfoil, and a root attachment which is dimensioned to fit within, and to engage a corresponding hub. Viscoelastic dampers are selectively applied to the outer surfaces of the root attachment on which compressive or shear forces are likely to develop, intermediate the root attachment and the hub, for compression therebetween upon rotation of the rotor disc, in order to dampen structural vibrations. One advantage presented by the viscoelastic dampers lies in its simplicity, efficiency, cost effectiveness, and its ability to be retrofitted into existing turbomachines with minor surface treatment of the root attachments. Furthermore, since the dampers are not exposed to the inflowing airstream, they do not affect the aerodynamic performance of the turbomachine. Another feature of the damping system is that it provides a significant source of damping to minimize destructive structural vibrations, thereby increasing the durability of the turbomachine, and reducing acoustic noise accompanying high amplitude vibrations.

Nguyen, Nhan↗

NASA NTRS1995

Parametric Investigation of The Aeromechanic Stability of Bearingless Rotors

The objective of this investigation is to conduct a parametric investigation on the aeromechanic stability of modern bearingless rotors. To ensure aeromechanic stability, modem bearingless; rotors use elastomeric dampers to augment the blade inplane damping. The augmented dampers are necessary to avoid aeromechanic instabilities such as air and ground resonance on soft-inplane rotors. The prevention of air and ground resonance depends largely on the damping level of the rotor-fuselage system during the critical frequency-crossing between the rotor and the fuselage inplane motions. The blade inplane damping, critical in ensuring aeromechanic stability of a rotor, depends not only on the damper sizes but also on the aeroelastic properties of the rotor blade. The results of this investigation provide insight into the source of inplane damping. The parametric study is carried out analytically using the University of Maryland Advanced Rotorcraft Code, or UMARC.

Nguyen, Khanh Q.↗

NASA NTRS2004

Subsurface Stress Fields In Single Crystal (Anisotropic) Contacts

Single crystal superalloy turbine blades used in high pressure turbomachinery are subject to conditions of high temperature, triaxial steady and alternating stresses, fretting stresses in the blade attachment and damper contact locations, and exposure to high-pressure hydrogen. The blades are also subjected to extreme variations in temperature during start-up and shutdown transients. The most prevalent HCF failure modes observed in these blades during operation include crystallographic crack initiation/propagation on octahedral planes, and noncrystallographic initiation with crystallographic growth. Numerous cases of crack initiation and crack propagation at the blade leading edge tip, blade attachment regions, and damper contact locations have been documented. Understanding crack initiation/propagation under mixed-mode loading conditions is critical for establishing a systematic procedure for evaluating HCF life of single crystal turbine blades. This paper presents analytical and numerical techniques for evaluating two and three dimensional subsurface stress fields in anisotropic contacts. The subsurface stress results are required for evaluating contact fatigue life at damper contacts and dovetail attachment regions in single crystal nickel-base superalloy turbine blades. An analytical procedure is , presented, for evaluating the subsurface stresses in the elastic half-space, using a complex potential method outlined by Lekhnitskii. Numerical results are presented for cylindrical and spherical anisotropic contacts, using finite element analysis. Effects of crystal orientation on stress response and fatigue life are examined.

Arakere, Nagaraj K.↗

NASA NTRS2004

Subsurface Stress Fields in FCC Single Crystal Anisotropic Contacts

Single crystal superalloy turbine blades used in high pressure turbomachinery are subject to conditions of high temperature, triaxial steady and alternating stresses, fretting stresses in the blade attachment and damper contact locations, and exposure to high-pressure hydrogen. The blades are also subjected to extreme variations in temperature during start-up and shutdown transients. The most prevalent high cycle fatigue (HCF) failure modes observed in these blades during operation include crystallographic crack initiation/propagation on octahedral planes, and non-crystallographic initiation with crystallographic growth. Numerous cases of crack initiation and crack propagation at the blade leading edge tip, blade attachment regions, and damper contact locations have been documented. Understanding crack initiation/propagation under mixed-mode loading conditions is critical for establishing a systematic procedure for evaluating HCF life of single crystal turbine blades. This paper presents analytical and numerical techniques for evaluating two and three dimensional subsurface stress fields in anisotropic contacts. The subsurface stress results are required for evaluating contact fatigue life at damper contacts and dovetail attachment regions in single crystal nickel-base superalloy turbine blades. An analytical procedure is presented for evaluating the subsurface stresses in the elastic half-space, based on the adaptation of a stress function method outlined by Lekhnitskii. Numerical results are presented for cylindrical and spherical anisotropic contacts, using finite element analysis (FEA). Effects of crystal orientation on stress response and fatigue life are examined. Obtaining accurate subsurface stress results for anisotropic single crystal contact problems require extremely refined three-dimensional (3-D) finite element grids, especially in the edge of contact region. Obtaining resolved shear stresses (RSS) on the principal slip planes also involves considerable post-processing work. For these reasons it is very advantageous to develop analytical solution schemes for subsurface stresses, whenever possible.

Arakere, Nagaraj K.↗