SEARCH · Search NASA

Results for “Design Methods Modeling and Validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Spacecraft Fire Suppression: Testing and Evaluation

The objective of this project is the testing and evaluation of the effectiveness of a variety of fire suppressants and fire-response techniques that will be used in the next generation of spacecraft (Crew Exploration Vehicle, CEV) and planetary habitats. From the many lessons learned in the last 40 years of space travel, there is common agreement in the spacecraft fire safety community that a new fire suppression system will be needed for the various types of fire threats anticipated in new space vehicles and habitats. To date, there is no single fire extinguishing system that can address all possible fire situations in a spacecraft in an effective, reliable, clean, and safe way. The testing conducted under this investigation will not only validate the various numerical models that are currently being developed, but it will provide new design standards on fire suppression that can then be applied to the next generation of spacecraft extinguishment systems. The test program will provide validation of scaling methods by conducting small, medium, and large scale fires. A variety of suppression methods will be tested, such as water mist, carbon dioxide, and nitrogen with single and multiple injection points and direct or distributed agent deployment. These injection methods cover the current ISS fire suppression method of a portable hand-held fire extinguisher spraying through a port in a rack and also next generation spacecraft units that may have a multi-point suppression delivery system built into the design. Consideration will be given to the need of a crew to clean-up the agent and recharge the extinguishers in flight in a long-duration mission. The fire suppression methods mentioned above will be used to extinguish several fire scenarios that have been identified as the most relevant to spaceflight, such as overheated wires, cable bundles, and circuit boards, as well as burning cloth and paper. Further testing will be conducted in which obstructions and ventilation will be added to represent actual spacecraft conditions (e.g., a series of cards in a card rack).

Abbud-Madrid, Angel↗

NASA NTRS1997

Integrated Modeling Methodology Validation Using the Micro-Precision Interferometer Testbed: Assessment of Closed Loop Performance Prediction Capability

This paper validates the integrated modeling methodology used for design and performance evaluation of complex opto-mechanical systems, particularly spaceborne interferometers.

integrated↗

NASA NTRS1975

A coupled fluid-structure dynamic analysis for water impact loads

In this paper a nonlinear transient, hydroelastic method is developed for response analysis of the Space Shuttle recoverable booster on water impact. At each time step, coupled equations of fluid flow and structure dynamics are solved with an iterative, self-correcting process. Rigid body motions are represented by large angle equations. Local deformations are represented by a NASTRAN-generated model of the three-dimensional structure. The fluid is represented by series solutions of the potential flow equation which include the effects of the local structure motions. The resulting water loads and structural stresses obtained will aid in qualification of the final structural design. Comparisons are made to experimental impact data to validate the method.

Herting, D. N.↗

DOE OSTI2023

Dynamic Mooring Field Experiment and Design of a Wave Energy Converter Platform Test System

Abstract This study evaluated a multi-catenary spread mooring system design of a mobile ocean test berth for wave energy converters (WECs), the Ocean Sentinel (OS) instrumentation buoy, through dynamic simulation, numerical analysis, and comparison with measured field motion data of the OS off the OR coast. First, the accuracy of the numerical employed model based on a fully-coupled method of the OS and its mooring lines was validated by comparing predicted mooring tensions to the field measurements. Then, the anchor movability, fatigue damage, and extreme mooring tension of the OS mooring system were analyzed to assess survivability. Field test results show that the numerical model provided accurate predictions of mooring tensions even under environmental conditions of strong wind, current, and waves. Factors affecting the accuracy are discussed. One mooring anchor was shown to have moved significantly during the ocean field test. Mooring fatigue damage was calculated for different levels of sea states. Design strengths of the mooring lines were calculated and analyzed.

Engineering↗

NASA NTRS2002

Design of a Dual Waveguide Normal Incidence Tube (DWNIT) Utilizing Energy and Modal Methods

This report investigates the partition design of the proposed Dual Waveguide Normal Incidence Tube (DWNIT). Some advantages provided by the DWNIT are (1) Assessment of coupling relationships between resonators in close proximity, (2) Evaluation of "smart liners", (3) Experimental validation for parallel element models, and (4) Investigation of effects of simulated angles of incidence of acoustic waves. Energy models of the two chambers were developed to determine the Sound Pressure Level (SPL) drop across the two chambers, through the use of an intensity transmission function for the chamber's partition. The models allowed the chamber's lengthwise end samples to vary. The initial partition design (2" high, 16" long, 0.25" thick) was predicted to provide at least 160 dB SPL drop across the partition with a compressive model, and at least 240 dB SPL drop with a bending model using a damping loss factor of 0.01. The end chamber sample transmissions coefficients were set to 0.1. Since these results predicted more SPL drop than required, a plate thickness optimization algorithm was developed. The results of the algorithm routine indicated that a plate with the same height and length, but with a thickness of 0.1" and 0.05 structural damping loss, would provide an adequate SPL isolation between the chambers.

Betts, Juan F.↗

NASA NTRS2008

Demand access protocol design and validation with SPIN

In order for distributed systems to communicate reliably engineers standardize on communication rules (or protocols). Unforeseen behavior in communication protocols can push faults up to applications resulting in uncontrollable systems and should not be tolerated. However, while most modern protocols undergo extensive testing, rigorous formal methods, such as model checking,are rarely used due to complexity and massive incomputable state spaces.

Seguí, John S.↗

DOE OSTI2020

Optimization of Window Positions for Wind-Driven Natural Ventilation Performance

This paper optimizes opening positions on building facades to maximize the natural ventilation’s potential for ventilation and cooling purposes. The paper demonstrates how to apply computational fluid dynamics (CFD) simulation results to architectural design processes, and how the CFD-driven decisions impact ventilation and cooling: (1) background: A CFD helps predict the natural ventilation’s potential, the integration of CFD results into design decision-making has not been actively practiced; (2) methods: Pressure data on building facades were obtained from CFD simulations and mapped into the 3D modeling environment, which were then used to identify optimal positions of two openings of a zone. The effect of the selected opening positions was validated with building energy simulations; (3) results: The cross-comparison study of different window positions based on different geographical locations quantified the impact on natural ventilation effectiveness; and (4) conclusions: The optimized window position was shown to be effective, and some optimal solutions contradicted the typical cross-ventilation strategy.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1983

Control of large spaceborne antenna systems with flexible booms by mechanical decoupling

A simple practical method for designing antenna-feed attitude control systems for large deployable spaceborne antenna systems with long flexible booms is proposed. The basic idea is to mechanically decouple the antenna-feed from the boom so that the feed-attitude control system can be designed without taking the boom dynamics into consideration, thus avoiding a complex control problem involving an infinite-dimensional distributed parameter system. The validity of the proposed method is substantiated by analytical and numerical studies using a mathematical model for the flexible boom which could undergo both bending and torsional vibrations. This approach leads to simple antenna-feed attitude control systems which are amenable to physical implementation.

Wang, P. K. C.↗

NASA NTRS2004

Properties of a Formal Method for Prediction of Emergent Behaviors in Swarm-based Systems

Autonomous intelligent swarms of satellites are being proposed for NASA missions that have complex behaviors and interactions. The emergent properties of swarms make these missions powerful, but at the same time more difficult to design and assure that proper behaviors will emerge. This paper gives the results of research into formal methods techniques for verification and validation of NASA swarm-based missions. Multiple formal methods were evaluated to determine their effectiveness in modeling and assuring the behavior of swarms of spacecraft. The NASA ANTS mission was used as an example of swarm intelligence for which to apply the formal methods. This paper will give the evaluation of these formal methods and give partial specifications of the ANTS mission using four selected methods. We then give an evaluation of the methods and the needed properties of a formal method for effective specification and prediction of emergent behavior in swarm-based systems.

Rouff, Christopher↗

NASA NTRS2017

Internal Acoustics of the ISS and Other Spacecraft

It is important to control the acoustic environment inside spacecraft and space habitats to protect for astronaut communications, alarm audibility, and habitability, and to reduce astronauts' risk for sleep disturbance, and hear-ing loss. But this is not an easy task, given the various design trade-offs, and it has been difficult, historically, to achieve. Over time it has been found that successful control of spacecraft acoustic levels is achieved by levying firm requirements at the system-level, using a systems engineering approach for design and development, and then validating these requirements with acoustic testing. In the systems engineering method, the system-level requirements must be flowed down to sub-systems and component noise sources, using acoustic analysis and acoustic modelling to develop allocated requirements for the sub-systems and components. Noise controls must also be developed, tested, and implemented so the sub-systems and components can achieve their allocated limits. It is also important to have management support for acoustics efforts to maintain their priority against the various trade-offs, including mass, volume, power, cost, and schedule. In this extended abstract and companion presentation, the requirements, approach, and results for controlling acoustic levels in most US spacecraft since Apollo will be briefly discussed. The approach for controlling acoustic levels in the future US space vehicle, Orion Multipurpose Crew Vehicle (MPCV), will also be briefly discussed. These discussions will be limited to the control of continuous noise inside the space vehicles. Other types of noise, such as launch, landing, and abort noise, intermittent noise, Extra-Vehicular Activity (EVA) noise, emergency operations/off-nominal noise, noise exposure, and impulse noise are important, but will not be discussed because of time limitations.

Allen, Christopher S.↗

NASA NTRS2012

A Full-Envelope Air Data Calibration and Three-Dimensional Wind Estimation Method Using Global Output-Error Optimization and Flight-Test Techniques

A novel, efficient air data calibration method is proposed for aircraft with limited envelopes. This method uses output-error optimization on three-dimensional inertial velocities to estimate calibration and wind parameters. Calibration parameters are based on assumed calibration models for static pressure, angle of attack, and flank angle. Estimated wind parameters are the north, east, and down components. The only assumptions needed for this method are that the inertial velocities and Euler angles are accurate, the calibration models are correct, and that the steady-state component of wind is constant throughout the maneuver. A two-minute maneuver was designed to excite the aircraft over the range of air data calibration parameters and de-correlate the angle-of-attack bias from the vertical component of wind. Simulation of the X-48B (The Boeing Company, Chicago, Illinois) aircraft was used to validate the method, ultimately using data derived from wind-tunnel testing to simulate the un-calibrated air data measurements. Results from the simulation were accurate and robust to turbulence levels comparable to those observed in flight. Future experiments are planned to evaluate the proposed air data calibration in a flight environment.

Taylor, Brian R.↗

NASA NTRS1993

Model reduction in integrated controls-structures design

It is the objective of this paper to present a model reduction technique developed for the integrated controls-structures design of flexible structures. Integrated controls-structures design problems are typically posed as nonlinear mathematical programming problems, where the design variables consist of both structural and control parameters. In the solution process, both structural and control design variables are constantly changing; therefore, the dynamic characteristics of the structure are also changing. This presents a problem in obtaining a reduced-order model for active control design and analysis which will be valid for all design points within the design space. In other words, the frequency and number of the significant modes of the structure (modes that should be included) may vary considerably throughout the design process. This is also true as the locations and/or masses of the sensors and actuators change. Moreover, since the number of design evaluations in the integrated design process could easily run into thousands, any feasible order-reduction method should not require model reduction analysis at every design iteration. In this paper a novel and efficient technique for model reduction in the integrated controls-structures design process, which addresses these issues, is presented.

Maghami, Peiman G.↗

DOE OSTI2024

Geometry-complete diffusion for 3D molecule generation and optimization

Abstract Generative deep learning methods have recently been proposed for generating 3D molecules using equivariant graph neural networks (GNNs) within a denoising diffusion framework. However, such methods are unable to learn important geometric properties of 3D molecules, as they adopt molecule-agnostic and non-geometric GNNs as their 3D graph denoising networks, which notably hinders their ability to generate valid large 3D molecules. In this work, we address these gaps by introducing the Geometry-Complete Diffusion Model (GCDM) for 3D molecule generation, which outperforms existing 3D molecular diffusion models by significant margins across conditional and unconditional settings for the QM9 dataset and the larger GEOM-Drugs dataset, respectively. Importantly, we demonstrate that GCDM’s generative denoising process enables the model to generate a significant proportion of valid and energetically-stable large molecules at the scale of GEOM-Drugs, whereas previous methods fail to do so with the features they learn. Additionally, we show that extensions of GCDM can not only effectively design 3D molecules for specific protein pockets but can be repurposed to consistently optimize the geometry and chemical composition of existing 3D molecules for molecular stability and property specificity, demonstrating new versatility of molecular diffusion models. Code and data are freely available on GitHub .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2021

The Causes of Propeller Pitching Moment and the Conditions for its Significance

Recent development of vertical takeoff and landing (VTOL) aircraft has renewed interest in the study of propellers. One metric in particular, the propeller pitching moment, has been observed to be important to VTOL aircraft stability and control in the past. Propellers at angles of attack could not be accurately modeled in generations past due to a lack of computational power, but even with advances in computer technology, modern designers seem to possess insufficient knowledge in this area. In this dissertation, we study the physics behind propeller pitching moment in the context of an isolated propeller and a propeller upstream of a wing. An unsteady 3D vortex lattice method is developed specifically to model propellers at angles of attack and is validated by comparing to high-fidelity CFD analyses. We then use the model to isolate velocity influences to show that the propeller pitching moment is largely caused by two effects: a skewed wake and the presence of wing circulation. Generated maps of propeller pitching moment over a range of operational parameters corresponding to VTOL transition show that the low flight speeds and high angles of attack encountered during transition lead to significant magnitudes of propeller pitching moment that would be difficult to trim using passive methods. Also, derivation of a generalizable metric of significance shows that the peak contribution of propeller pitching moment to aircraft stability is comparable to a longitudinal displacement of the center of gravity by several percent of the wing chord. Finally, we give a concluding discussion on the impact of propeller pitching moment on VTOL aircraft design.

Xiaofan Fei↗

DOE OSTI2022

Bayesian optimized collection strategies for fatigue strength testing

Abstract A statistical framework is presented enabling optimal sampling and analysis of constant life fatigue data. Protocols using Bayesian maximum entropy sampling are built based on conventional staircase and stress step methods, reducing the requirement of prior knowledge for data collection. The Bayesian Staircase method shows improved parameter estimation efficiency, and the Bayesian Stress Step method shows equal accuracy to the standard method at larger step size allowing experimentalists to lessen concerns of loading history. Statistical methods for determining model suitability are shown, highlighting the influence of protocol. Experimental validation is performed, showing the applicability of the methods in laboratory testing.

36 MATERIALS SCIENCE↗

NASA NTRS2019

Challenges in Qualification of Thermal Protection Systems in Extreme Entry Environments

Planetary entry vehicles employ ablative TPS materials to shield the aeroshell from entry aeroheating environments. To ensure mission success, it must be demonstrated that the heat shield system, including local features such as seams, does not fail at conditions that are suitably margined beyond those expected in flight. Furthermore, its thermal response must be predictable, with acceptable fidelity, by computational tools used in heat shield design. Mission assurance is accomplished through a combination of ground testing and material response modelling. A material's robustness to failure is verified through arcjet testing while its thermal response is predicted by analytical tools that are verified against experimental data. Due to limitations in flight-like ground testing capability and lack of validated high-fidelity computational models, qualification of heat shield materials is often achieved by piecing together evidence from multiple ground tests and analytical simulations, none of which fully bound the flight conditions and vehicle configuration. Extreme heating environments (>2000 W/sq. cm heat flux and >2 atm pressure), experienced during entries at Venus, Saturn and Ice Giants, further stretch the current testing and modelling capabilities for applicable TPS materials. Fully-dense Carbon Phenolic was the material of choice for these applications; however, since heritage raw materials are no longer available, future uses of re-created Carbon Phenolic will require re-qualification. To address this sustainability challenge, NASA is developing a new dual-layer material based on 3D weaving technology called Heat shield for Extreme Entry Environments (HEEET). Regardless of TPS material, extreme environments pose additional certification challenges beyond what has been typical in recent NASA missions. Scope of this presentation: This presentation will give an overview of challenges faced in verifying TPS performance at extreme heating conditions. Examples include: (1) Bounding aeroheating parameters (heat flux, pressure, shear and enthalpy) in ground facilities. How to certify TPS if environments can't be bounded or aeroheating parameters can't be simultaneously achieved. (2) Higher uncertainties in ground test environments (facility calibration and analytical predictions) at extreme conditions. (3) Testing in flows similar to planetary atmosphere composition (H2/He for Gas and Ice Giants). (4) Test sample size limitations for qualifying seam designs. (5) Lack of computational tools capable of simulating all significant aspects of TPS performance (including initiation and propagation of failures). This presentation will provide recommendations on how the EDL community can address these challenges and mitigate some of the risks involved in flying TPS materials at extreme conditions. Examples include: (1) Dedicated activity to understanding TPS failure modes. Develop computational tools capable of modelling fluid interaction with material's thermostructural response. Validate these tools through failure testing. A better understanding of failure mechanisms may eliminate the need to fully bound all aeroheating parameters in ground testing. (2) Enhancements to current testing facilities to simulate flight-like ablation mechanism (ex. testing in Nitrogen at Ames Interaction Heating Facility to limit oxidation in favor of more sublimation). (3) Improved characterization of test conditions with new diagnostic methods and determination of environment uncertainty through rigorous statistical analysis of available data. (4) Design margin policies that are directly tied to uncertainties in ground test environments and modelling fidelity

Mahzari, Milad↗

NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

A flow quantification method has previously been developed that uses high-speed shadowgraph images to extract frequency content of a transonic flow field around a wind-tunnel model. In this method, a classical spectral analysis is performed on shadowgraph video pixels to identify their intensity fluctuation frequencies. The spatial change of the image intensity is related to the second derivative of the density gradient. Examining the change of the density gradient as a function of time can be used to understand the flow-field pressure fluctuations. Time-varying pressure measurements collected during a Space Launch System (SLS) unsteady aerodynamic test of an advanced Block 2 booster design are used to calibrate the shadowgraph-based measurements. The test was performed at the NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-foot test section and investigated the aerodynamic environment downstream of candidate booster forward attachment hardware geometries of the SLS Block 2 Cargo configuration. Time-correlated shadowgraph video and model surface pressure measurements were acquired during the test and served as an ideal opportunity to calibrate and validate the shadowgraph image intensity method.

Shadowgraph↗

NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

Shadowgraph↗