Search NASA⌕ Search

SEARCH · Search NASA

Results for “Experimental Data Comparison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Investigation of Iso-octane Ignition and Validation of a Multizone Modeling Method in an Ignition Quality Tester

An ignition quality tester was used to characterize the autoignition delay times of iso-octane. The experimental data were characterized between temperatures of 653 and 996 K, pressures of 1.0 and 1.5 MPa, and global equivalence ratios of 0.7 and 1.05. A clear negative temperature coefficient behavior was seen at both pressures in the experimental data. These data were used to characterize the effectiveness of three modeling methods: a single-zone homogeneous batch reactor, a multizone engine model, and a three-dimensional computational fluid dynamics (CFD) model. A detailed 874 species iso-octane ignition mechanism (Mehl, M.; Curran, H. J.; Pitz, W. J.; Westbrook, C. K.Chemical kinetic modeling of component mixtures relevant to gasoline. Proceedings of the European Combustion Meeting; Vienna, Austria, April 14-17, 2009) was reduced to 89 species for use in these models, and the predictions of the reduced mechanism were consistent with ignition delay times predicted by the detailed chemical mechanism across a broad range of temperatures, pressures, and equivalence ratios. The CFD model was also run without chemistry to characterize the extent of mixing of fuel and air in the chamber. The calculations predicted that the main part of the combustion chamber was fairly well-mixed at longer times (> ~30 ms), suggesting that the simpler models might be applicable in this quasi-homogeneous region. The multizone predictions, where the combustion chamber was divided into 20 zones of temperature and equivalence ratio, were quite close to the coupled CFD-kinetics results, but the calculation time was ~11 times faster than the coupled CFD-kinetics model. Although the coupled CFD-kinetics model captured the observed negative temperature coefficient behavior and pressure dependence, discrepancies remain between the predictions and the observed ignition time delays, suggesting improvements are still needed in the kinetic mechanism and/or the CFD model. This approach suggests a combined modeling approach, wherein the CFD calculations (without chemistry) can be used to examine the sensitivity of various model inputs to in-cylinder temperature and equivalence ratios. In conclusion, these values can be used as inputs to the multizone model to examine the impact on ignition delay. Additionally, the speed of the multizone model also makes it feasible to quickly test more detailed kinetic mechanisms for comparison to experimental data and sensitivity analysis.

33 ADVANCED PROPULSION SYSTEMS↗

Simulation of electron thermal transport in H-mode discharges

Electron thermal transport in DIII-D H-mode tokamak plasmas [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] is investigated by comparing predictive simulation results for the evolution of electron temperature profiles with experimental data. The comparison includes the entire profile from the magnetic axis to the bottom of the pedestal. In the simulations, carried out using the automated system for transport analysis (ASTRA) integrated modeling code, different combinations of electron thermal transport models are considered. The combinations include models for electron temperature gradient (ETG) anomalous transport and trapped electron mode (TEM) anomalous transport, as well as a model for paleoclassical transport [J. D. Callen, Nucl. Fusion 45, 1120 (2005)]. It is found that the electromagnetic limit of the Horton ETG model [W. Horton et al., Phys. Fluids 31, 2971 (1988)] provides an important contribution near the magnetic axis, which is a region where the ETG mode in the GLF23 model [R. E. Waltz et al., Phys. Plasmas 4, 2482 (1997)] is below threshold. In simulations of DIII-D discharges, the observed shape of the H-mode edge pedestal is produced when transport associated with the TEM component of the GLF23 model is suppressed and transport given by the paleoclassical model is included. In a study involving 15 DIII-D H-mode discharges, it is found that with a particular combination of electron thermal transport models, the average rms deviation of the predicted electron temperature profile from the experimental profile is reduced to 9% and the offset to -4%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of preform architecture on modulus and strength of 2-D triaxially braided textile composites

Laminates formed using braided fibrous preforms have been extensively investigated during the course of the past few years as alternatives to unidirectional prepreg tape systems. This paper focused on one aspect of that work. It defined the role of the fibrous preform architecture in controlling a laminate's mechanical properties. The presentation was divided into four sections as the outline listed above illustrates. The presentation began with a brief introduction which defined the objectives of the study and detailed the materials studied. This was followed by a review of empirical test results. The materials' moduli and strengths were measured in both tension and compression. Their shear moduli were also experimentally determined. The review of the empirical data comprised the bulk of the presentation. A comparison of the experimental data to results predicted analytically was then presented. The presentation concluded with a few summary remarks. The specimens studied in this investigation featured 2-D triaxially braided AS4 graphite fiber preforms impregnated with Shell 1895 epoxy resin.

Masters, John E.↗

Simplified Approach to Predicting Rough Surface Transition

Turbine vane heat transfer predictions are given for smooth and rough vanes where the experimental data show transition moving forward on the vane as the surface roughness physical height increases. Consistent with smooth vane heat transfer, the transition moves forward for a fixed roughness height as the Reynolds number increases. Comparisons are presented with published experimental data. Some of the data are for a regular roughness geometry with a range of roughness heights, Reynolds numbers, and inlet turbulence intensities. The approach taken in this analysis is to treat the roughness in a statistical sense, consistent with what would be obtained from blades measured after exposure to actual engine environments. An approach is given to determine the equivalent sand grain roughness from the statistics of the regular geometry. This approach is guided by the experimental data. A roughness transition criterion is developed, and comparisons are made with experimental data over the entire range of experimental test conditions. Additional comparisons are made with experimental heat transfer data, where the roughness geometries are both regular and statistical. Using the developed analysis, heat transfer calculations are presented for the second stage vane of a high pressure turbine at hypothetical engine conditions.

Boyle, R. J.↗

Polyacrylonitrile Interactions with Carbon Nanotubes in Solution: Conformations and Binding as a Function of Solvent, Temperature, and Concentration

Abstract Polyacrylonitrile (PAN) is among the most promising precursor polymers to produce strong and lightweight carbon fiber. Conformations in solution and the extent of binding to carbon nanotubes (CNTs) are critical during gel spinning and for alignment of graphitic layers upon carbonization. Here, quantitative insights into these processes are reported using molecular dynamics simulations at the atomic scale including virtual π electrons and comparisons to experimental data. Common solvents for fiber spinning induce significant differences in PAN conformation in dilute solutions at 25 °C with persistence lengths between 0.5 and 2 nm. Variations in conformation become smaller at 75 °C, in the presence of CNTs, and at higher PAN concentration. “Aging” of PAN conformations in dimethylformamide and dimethylsulfoxide at higher temperature is explained and a correlation between extended polymer conformations and increased binding to CNTs is identified in dilute solutions. PAN is overall barely attracted to CNTs under common solution conditions and enters significant surface contact only at higher concentration as solvent is physically removed. The impact of temperature is small, whereby binding increases at lower temperatures. The results provide guidance to control interactions of polymers with CNTs to induce distinct conformations and specific binding at the early stages of assembly.

Pramanik, Chandrani↗

Gamma Radiation-Induced Degradation of Acetohydroxamic Acid (AHA) in Aqueous Nitrate and Nitric Acid Solutions Evaluated by Multiscale Modelling

Acetohydroxamic acid (AHA) has been proposed for inclusion in advanced, single-cycle, used nuclear fuel reprocessing solvent systems for the reduction and complexation of plutonium and neptunium ions. For this application, a detailed description of the degradation of AHA in dilute aqueous nitric acid is required. To this end, we present a comprehensive, multiscale computer model for the coupled radiolytic and hydrolytic degradation of AHA in aqueous sodium nitrate and nitric acid solutions. Rate coefficients for the reactions of AHA and HA with the oxidizing nitrate radical were measured for the first time using pulsed electron radiolysis and used as inputs in the kinetic model. The computer model results are validated by comparison to experimental data from steady state gamma irradiations, for which the agreement is excellent. Here, the presented model accurately predicts the yields of the major degradation products of AHA: acetic acid, hydroxylamine, nitrous oxide, and molecular hydrogen.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The denatured state of HIV ‐1 protease under native conditions

Abstract The denatured state of several proteins has been shown to display transient structures that are relevant for folding, stability, and aggregation. To detect them by nuclear magnetic resonance (NMR) spectroscopy, the denatured state must be stabilized by chemical agents or changes in temperature. This makes the environment different from that experienced in biologically relevant processes. Using high‐resolution heteronuclear NMR spectroscopy, we have characterized several denatured states of a monomeric variant of HIV‐1 protease, which is natively structured in water, induced by different concentrations of urea, guanidinium chloride, and acetic acid. We have extrapolated the chemical shifts and the relaxation parameters to the denaturant‐free denatured state at native conditions, showing that they converge to the same values. Subsequently, we characterized the conformational properties of this biologically relevant denatured state under native conditions by advanced molecular dynamics simulations and validated the results by comparison to experimental data. We show that the denatured state of HIV‐1 protease under native conditions displays rich patterns of transient native and non‐native structures, which could be of relevance to its guidance through a complex folding process.

60 APPLIED LIFE SCIENCES↗

Experimental validation of a Kalman observer using linearized OpenFAST and a fully instrumented 1:70 model

Abstract To enable real‐time monitoring and control strategies for floating offshore wind turbines, accurate information about the state of the system is needed. This paper details the application of a Kalman filter to the UMaine VolturnUS‐S floating wind platform to provide accurate state estimates in real time using minimal system measurements. The midfidelity nonlinear simulation tool OpenFAST was used to generate the underlying linear state‐space model for the Kalman filter. This linear model and its limitations are demonstrated through comparison with experimental data collected on a 1:70 froude‐scaled model of the floating platform and tower. Using a selection of five measurements from the real system, a Kalman filter was developed to provide estimates for the remaining system states and measurements. These estimates were then validated against the experimental values collected from testing of the scale model. Validation of the Kalman filter produced accurate estimates of surge, heave, and tower base bending moment, measurements of which were not available to the Kalman filter. Performance of the Kalman filter was tested and validated over a range of sea conditions from rated wind speed to storm events and demonstrated robustness in the Kalman filter to maintain accuracy across all operating conditions despite significant error in the underlying linear model for extreme conditions.

17 WIND ENERGY↗

A new approach to color-coherent parton evolution

We present a simple parton-shower model that replaces the explicit angular ordering of the coherent branching formalism with a differentially accurate simulation of soft-gluon radiation by means of a non-trivial dependence of the splitting functions on azimuthal angles. We introduce a global kinematics mapping and provide an analytic proof that it satisfies the criteria for next-to leading logarithmic accuracy. In the new algorithm, initial and final state evolution are treated on the same footing. We provide an implementation for final-state evolution in the numerical code ALARIC and present a first comparison to experimental data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nonlinear Creep Deformation of Polycarbonate at High Stress Level: Experimental Investigation and Finite Element Modeling

It is well known that polycarbonate (PC) undergoes time-dependent deformation (i.e., creep deformation), and nonlinear creep deformation is often experienced at high stress level. Using the time–temperature–stress superposition principle (TTSSP), we obtain a new master curve, which covers higher stress level, and successfully establish a new modeling method of creep deformation of PC. First, to investigate the effect of applied stress level on the creep compliance (i.e., stress-dependent nonlinear creep deformation), this study conducted various creep tests with eight different stress levels. We found that the creep compliance curve strongly depended on the applied stress level; in particular, a higher stress level induced a larger difference in creep compliance. According to the TTSSP, the creep compliance curve at each stress level shifts with the creep time (i.e., stress reduced time). When we appropriately selected the stress reduced time, we obtained the master curve of creep compliance, which is unified with respect to various applied stresses. However, we found that the stress-shifted factor is not compliant with the previous TTSSP, especially in the higher stress regime. Therefore, this regime was also considered to obtain a new master curve that can cover a wide range of stress levels. Finally, our established creep model (master curve and stress shift factor) was introduced into FEM, and then this numerical model was verified by comparison with experimental data. Our model may be useful for predicting the creep deformation of PC subjected to a wide range of applied stresses.

36 MATERIALS SCIENCE↗

Sensitivity Analysis of Material Model Parameters to Reproduce Crushing of Composite Tubes

The ability to predict the behavior of composite structures under impact conditions is an important challenge for engineering analysis since it requires modeling beyond the elasticity and into failure initiation and propagation. Crushing of laminate composites is the result of a combination of several and complex failure mechanisms, which are not always possible to reproduce together in a single finite element analysis (FEA). In this paper, models based on lamina-level failure criteria have been used to predict the onset of damage; once failure initiates, the mechanisms of failure propagation require reducing the material properties using several degradation schemes. Among the composite material models available in LS-DYNA, MAT-ENHANCED-COMPOSITE-DAMAGE (MAT-54) has been chosen for modeling the axial crushing of composite tubes with various resistant sections and wall slope, given the reduced experimental input parameters to insert into the card definition. Comparison with experimental data shows that such material model is able to successfully reproduce the crushing behavior, even if the numerical results are strictly correlated with some model parameters which cannot be measured experimentally or are purely mathematical expedients. Therefore, extensive calibration of these parameters by trial-and-error is necessary to achieve successful simulation results. Once done it for a structure made of the same composite material, it is possible to adopt the same card configuration for all the other cases, obtaining good agreement between numerical and experimental results. After, the attempt to model the same geometries using the MAT-LAMINATED-COMPOSITE-FABRIC (MAT-58) card with the same parameter values previously calibrated has been done obtaining results comparable with the experimental data.

36 MATERIALS SCIENCE↗

Application of a computational glass model to the shock response of soda-lime glass

This article details the implementation and application of the glass-specific computational constitutive model by Holmquist and Johnson [1] to simulate the dynamic response of soda-lime glass under high rate and high pressure shock conditions. The predictive capabilities of this model are assessed through comparison of experimental data with numerical results from computations using the CTH shock physics code. The formulation of this glass model is reviewed in the context of its implementation within CTH. Using a variety of experimental data compiled from the open literature, a complete parameterization of the model describing the observed behavior of soda-lime glass is developed. Simulation results using the calibrated soda-lime glass model are compared to flyer plate and Taylor rod impact experimental data covering a range of impact and failure conditions spanning an order of magnitude in velocity and pressure. In conclusion, the complex behavior observed in the experimental testing is captured well in the computations, demonstrating the capability of the glass model within CTH.

36 MATERIALS SCIENCE↗

Validation of hydrogen gas stratification and mixing models

Two validation benchmarks confirm that the BMIX++ code is capable of simulating unintended hydrogen release scenarios efficiently. The BMIX++ (UC Berkeley mechanistic MIXing code in C++) code has been developed to accurately and efficiently predict the fluid mixture distribution and heat transfer in large stratified enclosures for accident analyses and design optimizations. The BMIX++ code uses a scaling based one-dimensional method to achieve large reduction in computational effort compared to a 3-D computational fluid dynamics (CFD) simulation. Two BMIX++ benchmark models have been developed. One is for a single buoyant jet in an open space and another is for a large sealed enclosure with both a jet source and a vent near the floor. Both of them have been validated by comparisons with experimental data. Excellent agreements are observed. The entrainment coefficients of 0.09 and 0.08 are found to fit the experimental data for hydrogen leaks with the Froude number of 99 and 268 best, respectively. In addition, the BIX++ simulation results of the average helium concentration for an enclosure with a vent and a single jet agree with the experimental data within a margin of about 10% for jet flow rates ranging from 1.21 × 10⁻⁴ to 3.29 × 10⁻⁴ m³/s. In conclusion, computing time for each BMIX++ model with a normal desktop computer is less than 5 min.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The role of spin–rotation coupling in the non-exponential decay of hydrogen-like heavy ions

Recent experiments carried out at the storage ring of GSI in Darmstadt reveal an unexpected oscillation in the orbital electron capture and subsequent decay of hydrogen-like {sup 140}Pr{sup 58+}, {sup 142}Pm{sup 60+} and {sup 122}I{sup 52+}. The modulations have periods of 7.069(8) s, 7.10(22) s and 6.1 s respectively in the laboratory frame and are superimposed on the expected exponential decays. In this paper we propose a semiclassical model in which the observed modulations arise from the coupling of rotation to the spins of electron and nucleus. We show that the modulations are connected to quantum beats and to the effect of the Thomas precession on the spins of bound electron and nucleus, the magnetic moment precessions of electron and nucleus and their cyclotron frequencies. We also show that the spin–spin coupling of electron and nucleus, though dominant relative to the magnetic moment coupling of electron and nucleus with the storage ring magnetic field, does not contribute to the modulation because these terms average out during the time of flight of the ions, or cancel out. The model also predicts that the anomaly cannot be observed if the motion of the ions is rectilinear, or if the ions are stopped in a target (decay of neutral atoms in solid environments). It also supports the notion that no modulation occurs for the β{sup +}-decay branch. -- Highlights: ► Spin precession of the spin of nucleus and electron in storage ring. ► Coupling of rotation to the spin of electron and nucleus. ► Modulation in the decay probability of the heavy ions induced by quantum beats. ► Comparison with experimental data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Plasma equation of state accounting for ion core volume

Highlights: •Thermodynamically consistent Saha model accounting for non-point ion cores is constructed. •The applicability range of the model is expanded on superhigh densities and moderate temperatures. •Experimental verification of the model is performed which has demonstrated that the achieved accuracy is about 1% for pressures larger than 11 Mbar. -- Abstract: Equation of state for gaseous plasma is well described by the Saha model. In the present paper, we include accounting for finite ion core volumes into this model. This improvement allows to expand the Saha model on superhigh densities and moderate temperatures where plasma can be considered liquid. In this domain, thermodynamics of the Saha model is essentially close to the one of the Tomas–Fermi model which is conventionally used for condensed matter. To construct wide-range equation of state, we imply interpolation of the two mentioned models providing rigorous thermodynamic consistency. Comparison with experimental data on shock adiabats shows good agreement for a very wide range of pressures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A new predictive multi-zone model for HCCI engine combustion

Here, this work introduces a new predictive multi-zone model for the description of combustion in Homogeneous Charge Compression Ignition (HCCI) engines. The model exploits the existing OpenSMOKE++ computational suite to handle detailed kinetic mechanisms, providing reliable predictions of the in-cylinder auto-ignition processes. All the elements with a significant impact on the combustion performances and emissions, like turbulence, heat and mass exchanges, crevices, residual burned gases, thermal and feed stratification are taken into account. Compared to other computational approaches, this model improves the description of mixture stratification phenomena by coupling a wall heat transfer model derived from CFD application with a proper turbulence model. Furthermore, the calibration of this multi-zone model requires only three parameters, which can be derived from a non-reactive CFD simulation: these adaptive variables depend only on the engine geometry and remain fixed across a wide range of operating conditions, allowing the prediction of auto-ignition, pressure traces and pollutants. This computational framework enables the use of detail kinetic mechanisms, as well as Rate of Production Analysis (RoPA) and Sensitivity Analysis (SA) to investigate the complex chemistry involved in the auto-ignition and the pollutants formation processes. In the final sections of the paper, these capabilities are demonstrated through the comparison with experimental data.

30 DIRECT ENERGY CONVERSION↗

Solution-based thermodynamic modeling of the Ni-Al-Mo system using first-principles calculations

A solution-based thermodynamic description of the ternary Ni–Al–Mo system is developed here, incorporating first-principles calculations and reported modeling of the binary Ni–Al, Ni–Mo and Al–Mo systems. To search for the configurations with the lowest energies of the N phase, the Alloy Theoretic Automated Toolkit (ATAT) was employed and combined with VASP. The liquid, bcc and γ-fcc phases are modeled as random atomic solutions, and the γ'-Ni3Al phase is modeled by describing the ordering within the fcc structure using two sublattices, summarized as (Al,Mo,Ni)0.75(Al,Mo,Ni)0.25. Thus, γ-fcc and γ'-Ni3Al are modeled with a single Gibbs free energy function with appropriate treatment of the chemical ordering contribution. In addition, notable improvements are the following: first, the ternary effects of Mo and Al in the B2-NiAl and D0a-Ni3Mo phases, respectively, are considered; second, the N-NiAl8Mo3 phase is described as a solid solution using a three-sublattice model; third, the X-Ni14Al75Mo11 phase is treated as a stoichiometric compound. Model parameters are evaluated using first-principles calculations of zero-Kelvin formation enthalpies and reported experimental data. In comparison with the enthalpies of formation for the compounds ψ-AlMo, θ-Al8Mo3 and B2-NiAl, the first-principles results indicate that the N-NiAl8Mo3 phase, which is stable at high temperatures, decomposes into other phases at low temperature. Resulting phase equilibria are summarized in the form of isothermal sections and liquidus projections. To clearly identify the relationship between the γ-fcc and γ'-Ni3Al phases in the ternary Ni–Al–Mo system, the specific γ-fcc and γ'-Ni3Al phase fields are plotted in x(Al)–x(Mo)–T space for a temperature range 1200–1800 K.

36 MATERIALS SCIENCE↗

Scaling and statistics of bottom-up synthesized armchair graphene nanoribbon transistors

Bottom-up assembled nanomaterials and nanostructures allow for the studies of rich and unprecedented quantum-related and mesoscopic transport phenomena. However, it can be difficult to quantify the correlations between the geometrical or structural parameters obtained from advanced microscopy and measured electrical characteristics when they are made into macroscopic devices. Here, we propose a strategy to connect the nanomaterial morphologies and the device performance through a Monte Carlo device model and apply it to understand the scaling trends of bottom-up synthesized armchair graphene nanoribbon (GNR) transistors. A new nanofabrication process is developed for GNR transistors with channel length down to 7 nm. Further, the impacts of the GNR spatial distributions and the device geometries on the device performance are investigated systematically through comparison of experimental data with the model. Through this study, challenges and opportunities of transistor technologies based on bottom-up synthesized GNRs are pinpointed, paving the way to the further improvement of the GNR device performance for future transistor technology nodes.

36 MATERIALS SCIENCE↗