Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

A technique for improved assessment of flow resistance characteristics of natural wetlands using Landsat data

In the past, one value of the roughness coefficient has frequently been used to represent the flow resistance characteristics of the entire natural wetland throughout the year. To improve the simulation of water flow through these natural vegetation communities, Landsat imagery and in situ flow measurements could be combined to produce a more detailed representation of flow resistance. The vegetation in a typical marshland drainage basin in south Florida was classified into five major categories using Landsat data. Flow measurements were then performed at characteristic sites in the basin. The measurements were taken at various depths during months of significant flow to examine the effect of seasonal growth. This information can be compared with the areal extent of the vegetation measured by satellite to more accurately simulate resistance to water flow in natural marshland drainage basins.

Gervin, J. C.↗
NASA NTRS1969

Flow direction measurement with fixed probes

Fixed-position probes for determination of flow direction in one and two planes are tested over a wide range of Reynolds numbers and Mach numbers. The work is limited to tests of a single probe design for two dimensional flow and a single design for three dimensional flow.

Dudzinski, T. J.↗
NASA NTRS2012

Wind-Tunnel and Flight Test Results for the Measurements of Flow Variables at Supersonic Speeds Using Improved Wedge and Conical Probes

The results of supersonic wind-tunnel tests on three probes at nominal Mach numbers of 1.6, 1.8 and 2.0 and flight tests on two of these probes up to a Mach number of 1.9 are described. One probe is an 8 deg. half-angle wedge with two total-pressure measurements and one static. The second, a conical probe, is a cylinder that has a 15 deg., semi-angle cone tip with one total-pressure orifice at the apex and four static-pressure orifices on the surface of the cone, 90 deg. apart, and about two-thirds of the distance from the cone apex to the base of the cone. The third is a 2 deg. semi-angle cone that has two static ports located 180 deg. apart about 1.5 inches behind the apex of the cone. The latter probe was included since it has been the "probe of choice" for wind-tunnel flow-field pressure measurements (or one similar to it) for the past half-century. The wedge and 15 deg. conical probes used in these tests were designed for flight diagnostic measurements for flight Mach numbers down to 1.35 and 1.15 respectively, and have improved capabilities over earlier probes of similar shape. The 15. conical probe also has a temperature sensor that is located inside the cylindrical part of the probe that is exposed to free-stream flow through an annulus at the apex of the cone. It enables the determination of free-stream temperature, density, speed of sound, and velocity, in addition to free-stream pressure, Mach number, angle of attack and angle of sideslip. With the time-varying velocity, acceleration can be calculated. Wind-tunnel tests of the two probes were made in NASA Langley Research Center fs Unitary Plan Wind Tunnel (UPWT) at Mach numbers of 1.6, 1.8, and 2.0. Flight tests were carried out at the NASA Dryden Flight Research Center (DFRC) on its F-15B aircraft up to Mach numbers of 1.9. The probes were attached to a fixture, referred to as the Centerline Instrumented Pylon (CLIP), under the fuselage of the aircraft. Problems controlling the velocity of the flow through the conical probe required for accurate temperature measurements are noted, as well as some calibration problems of the miniature pressure sensors that required a re-calculation of the flow variables. Data are presented for angle of attack, pressure and Mach number obtained in the wind tunnel and in flight. In the wind tunnel some transient data were obtained by translating the probes through the shock flow field created by a bump on the wind-tunnel wall.

Bobbitt, Percy J.↗
NASA NTRS1980

Techniques for aerodynamic and turbulence measurements in turbomachinery rotors

Nonoptical techniques currently used to measure flows in turbomachine rotors are reviewed, with particular reference to the measurement of the three-dimensional mean velocity, turbulence intensity, Reynolds stresses, static and stagnation pressures, and blade surface measurements. The high level of sophistication of rotor flow measurement techniques is demonstrated. Rotating probe measurements are well suited for low- and moderate-speed turbomachinery, while stationary quick-response probes (hot-wire and pressure probes) are applicable both in low- and high-speed turbomachines. Hot-wire probes, blade pressure transducers, and telemetry systems will provide the urgently needed basic information on steady and unsteady flow through a blade passage, including blade boundary layer, shock configuration, leakage and secondary flows.

Lakshminarayana, B.↗
NASA NTRS1995

Flow Splitter For Measuring Large Leaks

Flow splitter increases size of leak measured by helium mass-spectrometer leak detector. Multiplies maximum measurable rate of leakage by factor of 1,000. Leaking gas flows into manifold, where small fraction of flow diverted to leak detector. Bulk of flow removed by mechanical vacuum pump.

Hyatt, William S.↗
NASA NTRS1993

Flow field measurements in a crossing shockwave turbulent boundary layer interaction at Mach 3

An experimental study has been conducted to examine the flow field of the 3D crossing shock wave/turbulent boundary layer interaction. A symmetric pair of 9-deg fins were used to generate the crossing shocks. The incoming boundary layer was developed on the tunnel sidewall and thus was relatively thick, 0.49 arcsec, and suited for pitot probe surveys. The test conditions were a nominal Mach number of 3 and unit Reynolds number of 1.2 x 10 exp 7/ft. The measurements obtained included surface oil flow visualizations, surface static pressures, and boundary layer pitot pressure profiles. The results showed that downstream of the crossing shock intersection, the stagnation pressure losses were significant and the stagnation pressure profiles were highly nonuniform. Despite the severe shock disturbances, the law of the wall and the law of the wake were found to give relatively good agreement with the experimental data.

Lachowicz, Jason T.↗
NASA NTRS1979

Proceedings of the 25th International Instrumentation Symposium, May 7-10, 1979, Anaheim, California

The papers deal essentially with the instrumentation needs of the transportation industry, machinery diagnostics, and energy research. The sessions covered include: acoustic emission, reentry vehicle ground and flight testing, performance of nose tip materials, instrumentation for solar heating and cooling systems, vibration measurement, data acquisition and analysis, system for aerospace pressure measurements, wind tunnel instrumentation and control, energy source instrumentation, nondestructive testing, pressure and flow measurements, automated test facilities, strain measurements, electrooptical instrumentation, thermal measurements, microcomputer applications in instrumentation and automation, flight testing, blast pressure measurement, two-phase liquid/gas mass flow measurement, and machinery monitoring and instrumentation.

Conferences↗
NASA NTRS2013

Flow Control and Measurement in Electric Propulsion Systems: Towards an AIAA Reference Standard

Accurate control and measurement of propellant flow to a thruster is one of the most basic and fundamental requirements for operation of electric propulsion systems, whether they be in the laboratory or on flight spacecraft. Hence, it is important for the electric propulsion community to have a common understanding of typical methods for flow control and measurement. This paper addresses the topic of propellant flow primarily for the gaseous propellant systems which have dominated laboratory research and flight application over the last few decades, although other types of systems are also briefly discussed. While most flight systems have employed a type of pressure-fed flow restrictor for flow control, both thermal-based and pressure-based mass flow controllers are routinely used in laboratories. Fundamentals and theory of operation of these types of controllers are presented, along with sources of uncertainty associated with their use. Methods of calibration and recommendations for calibration processes are presented. Finally, details of uncertainty calculations are presented for some common calibration methods and for the linear fits to calibration data that are commonly used.

thrust measurement↗
NASA NTRS1981

Mean-flow and turbulence measurements in the vicinity of the trailing edge of an NACA (63 sub 1)-012 airfoil

The Langley aircraft noise reduction laboratory was used to measure mean flow and turbulence in the vicinity of a cusped-trailing edge of two dimensional NACA 631-012 airfoil at zero angle of attack. Naturally transitioned flow and artificially tripped flow were investigated. Flow regions studied include the boundary layer and the near wake. Measurements were made at a free stream Reynolds number based on airfoil chord of 1.25 x 10 to the 6th power and a free stream Mach number of 0.1. Distributions of streamwise mean velocity, integral properties of the mean flow, turbulent intensities, and Reynolds shear stress are reported. For the naturally transitioned flow, the general trends observed are similar to those reported for a fully developed turbulent boundary layer over a flat plate under zero pressure gradient, with the exception of the notable streamwise variations in the turbulence properties for the airfoil flow. The main effect of flow tripping is to eliminate these streamwise variations. Observed changes in the mean flow and turbulence fields caused by tripping are expected on the basis of the Reynolds number based on the boundary layer thickness.

Yu, J. C.↗
NASA NTRS2019

Flow-Field Measurements in a Wing-Fuselage Junction Using an Embedded Particle Image Velocimetry System

A novel, embedded, 2D Particle Image Velocimetry system has been developed and implemented to obtain off-body velocity measurements in the junction of an 8% wing-body configuration in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel. Although the initial purpose for implementing the system during this test was to evaluate system performance and identify potential risks, the system worked remarkably well and a considerable amount of data were obtained in the wing-fuselage junction near the trailing edge at a Reynolds Number of 2.4 Million and angle of attack of 5 degrees. In addition to providing notable efficiencies with regard to image acquisition and test operations, the PIV system proved to be quite capable of capturing unique details of the flow separation to complement the extensive suite of measurement techniques applied during the test. Instantaneous PIV vector fields reveal that the flow separation is not stationary but rather highly dynamic. Mean flow statistics calculated from the PIV measurements highlight where reverse flow and Reynolds stresses are concentrated in the separated region and agree well with results from the embedded Laser Doppler Velocimeter system and Computational Fluid Dynamics. The comparisons and additional insight gained during this effort will help guide system improvements for follow-on tests.

Jenkins, Luther N.↗
NASA NTRS1995

Fiber-Optic/Photoelastic Flow Sensors

Simple, rugged, lightweight transducers detect periodic vortices. Fiber-optic-coupled transducers developed to measure flows over wide dynamic ranges and over wide temperature ranges in severe environments. Used to measure flows of fuel in advanced aircraft engines. Feasibility of sensors demonstrated in tests of prototype sensor in water flowing at various temperatures and speeds. Particularly attractive for aircraft applications because optical fibers compact and make possible transmission of sensor signals at high rates with immunity from electromagnetic interference at suboptical frequencies. Sensors utilize optical-to-optical conversion via photoelastic effect.

Wesson, Laurence N.↗
NASA NTRS1992

Ly-alpha emission from cooling flows and measures of the dust content of rich clusters of galaxies

Ly-alpha and UV continuum fluxes from measurements across the emission-line regions of 10 'cooling flow' clusters of galaxies are tabulated. Comparison of Ly-alpha emission fluxes obtained with the IUE satellite with optical Balmer emission fluxes is used to demonstrate that the lines of sight to the centers of these clusters show an average excess reddening E(B-V) about 0.19 above foreground extinction. While some fraction of this may derive from localized extinction in the central (cooling flow) region of the cluster, a substantial portion of this effect should arise from an extended cluster component. The case where this extinction originates in the hot intracluster gas of the cluster halo is considered. Estimates for the corresponding 100-micron infrared emission, assuming grain properties similar to those of interstellar grains, place the expected emission at the about 1/2 Jy level for nearby clusters. Measurements from IRAS pointed mode observations of clusters are consistent with the expected values. These results are used to show that ISO and SIRTF may detect clusters to cosmological distances.

Hu, Esther M.↗
NASA NTRS2003

Steady and Unsteady Flow Field Measurements Within a NASA 22-Inch Fan Model

Results are presented of an experiment conducted to investigate possible sources of fan noise in the flow developed by a 22-in. (55.9 cm) diameter turbofan model. Flow diagnostic data were acquired to identify possible sources of both tone and broadband noise. Laser Doppler velocimetry was used to characterize the tip flows that develop within the rotor blade passages, the wake flow downstream of the rotor, and the shock waves that develop on the blades when operated at transonic relative tip speeds. Single-point hot-wire measurements were made in the rotor wake to determine the frequency content and the length scales of the flow unsteadiness. The results document the changes in the rotor wake flow with both rotor speed and axial distance downstream of the rotor. The data also show the tip flow development within the blade passage, its migration downstream, and (at high rotor speeds) its merging with the blade wake of the following blade. Data also depict the variation of the tip flow with tip clearance. LDV data obtained within the blade passages at high rotor speeds illustrate the passage-to-passage variation of the mean shock position. Spectra computed from the single-point hot-wire measurements illustrate how the energy in the flow oscillations is split between periodic and random components, and how this split varies with both radial and axial position in the rotor wake.

Podboy, Gary G.↗
NASA NTRS1988

Experimental evaluation of resistojet thruster plume shields

The exhaust of an engineering model resistojet has been investigated using rotary pitot probes and a rotary quartz crystal microbalance. The resistojet operated on CO2 propellant at a mass flow rate of 0.29 g/sec in both heated and unheated flows. Measurements of local flow angles in the near field of a conical plume shield indicated that the shield was not wholly effective in confining the flow to the region upstream of its exit plane. However, the absolute levels of the measured mass flux into the backflow region were very low, on the order of 7 x 10 to the -7 power g/sqcm/sec or less. The use of a circualr disk at the exit plane of the existing conical shield showed some benefit in decreasing the amount of backflow by a factor of two. Lastly, a detached shield placed upstream of the resistojet exit plane demonstrated a small degree of local shielding for the region directly behind it.

Carney, Lynnette M.↗
NASA NTRS1988

Experimental evaluation of resistojet thruster plume shields

The exhaust of an engineering model resistojet has been investigated using rotary pitot probes and a rotary quartz crystal microbalance. The resistojet operated on CO2 propellant at a mass flow rate of 0.29 g/sec in both heated and unheated flows. Measurements of local flow angles in the near field of a conical plume shield indicated that the shield was not wholly effective in confining the flow to the region upstream of its exit plane. However, the absolute levels of the measured mass flux into the backflow region were very low, on the order of 7 x 10 to the -7 power g/sq cm/sec or less. The use of a circular disk at the exit plane of the existing conical shield showed some benefit in decreasing the amount of backflow by a factor of two. Lastly, a detached shield placed upstream of the resistojet exit plane demonstrated a small degree of local shielding for the region directly behind it.

Carney, Lynnette M.↗
NASA NTRS1989

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 1: Results and discussion

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. The conclusions derived were: (1) intrusive probes can produce significant errors in the measurements of the velocity of jets if they are large in diameter and penetrate beyond the jet center; (2) rectangular jets without tabs, compared to circular jets of the same exit area, provide faster jet mixing; and (3) further mixing enhancement is possible by using mechanical tabs.

Brown, W. H.↗
NASA NTRS1989

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 2: Tabulated data

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. This volume contains tabulated data for each of the data runs cited in Volume 1. Baseline characteristics, mixing modifications (subsonic and supersonic, heated and unheated) and miscellaneous charts are included.

Brown, W. H.↗