Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUID BOUNDARY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Geometry and starvation effects in hydrodynamic lubrication

Numerical methods were used to determine the effects of lubricant starvation on the minimum film thickness under conditions of a hydrodynamic point contact. Starvation was effected by varying the fluid inlet level. The Reynolds boundary conditions were applied at the cavitation boundary and zero pressure was stipulated at the meniscus or inlet boundary. A minimum-film-thickness equation as a function of both the ratio of dimensionless load to dimensionless speed and inlet supply level was determined. By comparing the film generated under the starved inlet condition with the film generated from the fully flooded inlet, an expression for the film reduction factor was obtained. Based on this factor a starvation threshold was defined as well as a critically starved inlet. The changes in the inlet pressure buildup due to changing the available lubricant supply are presented in the form of three dimensional isometric plots and also in the form of contour plots.

Brewe, D. E.↗
NASA NTRS1982

Geometry and starvation effects in hydrodynamic lubrication

Numerical methods were used to detemine the effects of lubricant starvation on the minimum film thickness under conditions of a hydrodynamic point contact. Starvation was effected by varying the fluid inlet level. The Reynolds boundary conditions were applied at the cavitation boundary and zero pressure was stipulated at the meniscus or inlet boundary. A minimum film thickness equation as a function of both the ratio of dimensionless load to dimensionless speed and inlet supply level was determined. By comparing the film generated under the starved inlet condition with the film generated from the fully flooded inlet, an expression for the film reduction factor was obtained. Based on this factor a starvation threshold was defined as well as a critically starved inlet. The changes in the inlet pressure buildup due to changing the available lubricant supply are presented in the form of three dimensional isometric plots and also in the form of contour plots.

Brewe, D.↗
NASA NTRS1992

The FML compressor as a drive system for the LFSWT: A narrative

During 1988, a feasibility study was performed to decide how best to build a Laminar Flow Supersonic Wind Tunnel (LFSWT) at the NASA-Ames Fluid Mechanics Laboratory (FML) for boundary layer transition research. A full report was received in June 1988. The report was based on the following guidelines: continuous operation at Mach numbers within the range from 1.8-4.0 was required to impact the NASA 'HiStar' project; low disturbance flow is essential for transition research; minimum test section height is 8 inches; tunnel must fit in an FML test cell; tunnel design should be simple; and construction costs should be minimized. The study considered three drive system options: (1) use surplus JPL compressors and support equipment; (2) use of the FML compressor with ambient injectors; and (3) use of the FML compressor with injectors driven by the NASA-Ames 3000 psia air supply.

Laub, James↗
NASA NTRS1992

Numerical study on mixing of sprayed liquid in an LNG storage tank

This paper presents a numerical method to simulate the mixing of heavier LNG sprayed on lighter layer. Numerical results for evolutions of flow field and density field are obtained in a rectangular computational domain which includes the vicinity of the liquid surface. At the surface boundary, uniform distributions of the fluid velocity and the density are assumed. Detail structure of flow caused by impingements of liquid drops are neglected. But, to trigger a realistic motion, a series of random numbers is employed. It is used as an initial distribution of the density near the surface. This method successfully gives a realistic simulation of the mixing process. Numerical results for mixing velocity shows good agreement with experimental data.

Uchida, Hiroyuki↗
NASA NTRS1994

The Eady problem for a basic state with zero PV gradient but beta does not equal 0

The classic Eady problem is modified to include beta does not equal 0, but with the basic distributions of temperature and zonal flow adjusted to preserve zero meridional gradients of basic-state potential vorticity in the fluid interior. Much of the mathematical simplicity of the classic problem is retained; however, the results differ in important ways. Specifically, the instability now has a long-wave cutoff in addition to the traditional short-wave cutoff. The former is associated with the fact that the phase speeds of the edge waves begin to differ so much as wavenumber is reduced that the two edge waves can no longer interact in order to form unstable modes. For the unstable modes, this manifests itself in that the steering level for unstable modes is always below the middle of the fluid and approaches the lower boundary near the long-wave cutoff. Relatedly, the amplitude of the unstable geopotential perturbations is larger at the upper boundary than at the lower boundary. Finally, below the long-wave cutoff, one of the neutral waves has a phase speed that becomes increasingly easterly as wavenumber decreases. This allows a resonant response to planetary-scale stationary forcing.

Lindzen, Richard S.↗
NASA NTRS2000

Preliminary Design Optimization For A Supersonic Turbine For Rocket Propulsion

In this study, we present a method for optimizing, at the preliminary design level, a supersonic turbine for rocket propulsion system application. Single-, two- and three-stage turbines are considered with the number of design variables increasing from 6 to 11 then to 15, in accordance with the number of stages. Due to its global nature and flexibility in handling different types of information, the response surface methodology (RSM) is applied in the present study. A major goal of the present Optimization effort is to balance the desire of maximizing aerodynamic performance and minimizing weight. To ascertain required predictive capability of the RSM, a two-level domain refinement approach has been adopted. The accuracy of the predicted optimal design points based on this strategy is shown to he satisfactory. Our investigation indicates that the efficiency rises quickly from single stage to 2 stages but that the increase is much less pronounced with 3 stages. A 1-stage turbine performs poorly under the engine balance boundary condition. A portion of fluid kinetic energy is lost at the turbine discharge of the 1-stage design due to high stage pressure ratio and high-energy content, mostly hydrogen, of the working fluid. Regarding the optimization technique, issues related to the design of experiments (DOE) has also been investigated. It is demonstrated that the criteria for selecting the data base exhibit significant impact on the efficiency and effectiveness of the construction of the response surface.

Papila, Nilay↗
NASA NTRS2003

Towards an Automated Full-Turbofan Engine Numerical Simulation

The objective of this study was to demonstrate the high-fidelity numerical simulation of a modern high-bypass turbofan engine. The simulation utilizes the Numerical Propulsion System Simulation (NPSS) thermodynamic cycle modeling system coupled to a high-fidelity full-engine model represented by a set of coupled three-dimensional computational fluid dynamic (CFD) component models. Boundary conditions from the balanced, steady-state cycle model are used to define component boundary conditions in the full-engine model. Operating characteristics of the three-dimensional component models are integrated into the cycle model via partial performance maps generated automatically from the CFD flow solutions using one-dimensional meanline turbomachinery programs. This paper reports on the progress made towards the full-engine simulation of the GE90-94B engine, highlighting the generation of the high-pressure compressor partial performance map. The ongoing work will provide a system to evaluate the steady and unsteady aerodynamic and mechanical interactions between engine components at design and off-design operating conditions.

Reed, John A.↗
NASA NTRS2004

Multi-Fidelity Simulation of a Turbofan Engine With Results Zoomed Into Mini-Maps for a Zero-D Cycle Simulation

A Zero-D cycle simulation of the GE90-94B high bypass turbofan engine has been achieved utilizing mini-maps generated from a high-fidelity simulation. The simulation utilizes the Numerical Propulsion System Simulation (NPSS) thermodynamic cycle modeling system coupled to a high-fidelity full-engine model represented by a set of coupled 3D computational fluid dynamic (CFD) component models. Boundary conditions from the balanced, steady state cycle model are used to define component boundary conditions in the full-engine model. Operating characteristics of the 3D component models are integrated into the cycle model via partial performance maps generated from the CFD flow solutions using one-dimensional mean line turbomachinery programs. This paper highlights the generation of the high-pressure compressor, booster, and fan partial performance maps, as well as turbine maps for the high pressure and low pressure turbine. These are actually "mini-maps" in the sense that they are developed only for a narrow operating range of the component. Results are compared between actual cycle data at a take-off condition and the comparable condition utilizing these mini-maps. The mini-maps are also presented with comparison to actual component data where possible.

Turner, Mark G.↗
NASA NTRS2012

Integrated Structural/Acoustic Modeling of Heterogeneous Panels

A model for the dynamic response of heterogeneous media is presented. A given medium is discretized into a number of subvolumes, each of which may contain an elastic anisotropic material, void, or fluid, and time-dependent boundary conditions are applied to simulate impact or incident pressure waves. The full time-dependent displacement and stress response throughout the medium is then determined via an explicit solution procedure. The model is applied to simulate the coupled structural/acoustic response of foam core sandwich panels as well as aluminum panels with foam inserts. Emphasis is placed on the acoustic absorption performance of the panels versus weight and the effects of the arrangement of the materials and incident wave frequency.

Bednarcyk, Brett, A.↗
NASA NTRS1983

Importance of inlet boundary conditions for numerical simulation of combustor flows

Fluid dynamic computer codes for the mathematical simulation of problems in gas turbine engine combustion systems are required as design and diagnostic tools. To eventually achieve a performance standard with these codes of more than qualitative accuracy it is desirable to use benchmark experiments for validation studies. Typical of the fluid dynamic computer codes being developed for combustor simulations is the TEACH (Teaching Elliptic Axisymmetric Characteristics Heuristically) solution procedure. It is difficult to find suitable experiments which satisfy the present definition of benchmark quality. For the majority of the available experiments there is a lack of information concerning the boundary conditions. A standard TEACH-type numerical technique is applied to a number of test-case experiments. It is found that numerical simulations of gas turbine combustor-relevant flows can be sensitive to the plane at which the calculations start and the spatial distributions of inlet quantities for swirling flows.

Sturgess, G. J.↗
NASA NTRS1981

The choice of numerical boundary conditions for hyperbolic systems

Two fundamental problems for mixed initial boundary value problems with applications in fluid mechanics are discussed. First, different stability properties are discussed which are of importance for long time integrations and steady state calculations. Secondly, a new numerical technique for problems with an artificial boundary is introduced.

Gustafson, B.↗
NASA NTRS1990

Conditions at the downstream boundary for simulations of viscous incompressible flow

The proper specification of boundary conditions at artificial boundaries for the simulation of time-dependent fluid flows has long been a matter of controversy. A general theory of asymptotic boundary conditions for dissipative waves is applied to the design of simple, accurate conditions at downstream boundary for incompressible flows. For Reynolds numbers far enough below the critical value for linear stability, a scaling is introduced which greatly simplifies the construction of the asymptotic conditions. Numerical experiments with the nonlinear dynamics of vortical disturbances to plane Poiseuille flow are presented which illustrate the accuracy of our approach. The consequences of directly applying the scalings to the equations are also considered.

Hagstrom, Thomas↗
NASA NTRS1991

Seal Technology at Rocketdyne

Seal codes currently in use and their capabilities are discussed. Among the codes currently in use are codes for simulating floating ring seals, face seals, and load sharing seals. New codes that will extend simulation capability to barotropic fluid properties, phase change, brush seal performance, large scale roughness, and asymmetric boundary conditions are under development. Planned seal testing and fluid film bearing activity are also presented.

Scharrer, Joe↗
NASA NTRS1993

High accuracy computation of fluid-structure interaction in transonic cascades

A coupling strategy for simulating fluid-structure interaction phenomena is formulated and applied to the prediction of flutter in transonic cascades. The flow is governed by the Euler equations and discretized using a finite volume flux-splitting scheme. The structure is modeled using an isoparametric finite element formulation. The coupling strategy successfully reconciles these two formulations at the fluid-structure interface by enforcing both kinematic and kinetic boundary conditions. In particular, the conservation laws applicable to the combined fluid-structure system are preserved across the interface. Since the primary mechanism driving aeroelastic phenomena involves energy exchange occurring at the interface, this highly accurate coupling mechanism is believed to improve the predictive capability of the scheme. The coupled equations are advanced simultaneously in time using an implicit time integration method. Results obtained using the coupling method are presented for cascade geometries operating in transonic flow.

Boschitsch, Alexander↗
NASA NTRS2004

TopMaker: A Technique for Automatic Multi-Block Topology Generation Using the Medial Axis

A two-dimensional multi-block topology generation technique has been developed. Very general configurations are addressable by the technique. A configuration is defined by a collection of non-intersecting closed curves, which will be referred to as loops. More than a single loop implies that holes exist in the domain, which poses no problem. This technique requires only the medial vertices and the touch points that define each vertex. From the information about the medial vertices, the connectivity between medial vertices is generated. The physical shape of the medial edge is not required. By applying a few simple rules to each medial edge, the multiblock topology is generated with no user intervention required. The resulting topologies contain only the level of complexity dictated by the configurations. Grid lines remain attached to the boundary except at sharp concave turns where a change in index family is introduced as would be desired. Keeping grid lines attached to the boundary is especially important in the area of computational fluid dynamics where highly clustered grids are used near no-slip boundaries. This technique is simple and robust and can easily be incorporated into the overall grid generation process.

Heidmann, James D.↗
NASA NTRS1987

Solitary waves in the resonant phenomenon between a surface gravity wave packet and an internal gravity wave

A two-layer inviscid incompressible fluid system of intermediate depth is considered. A multiple-scales perturbation technique is applied to the basic equations and boundary conditions for a two-layer fluid system to derive a system of weakly nonlinear partial integrodifferential equations governing the resonant interaction between a surface gravity wave packet and an internal gravity wave at an intermediate depth, providing a bridge between the existing shallow and deep fluid theories. The convolution integral term in these equations accounts for the dispersion in the lower-layer fluid. An iterative fast Fourier transform scheme is developed to find solitary wave solutions to this system of equations. The overtaking collision of two pairs of solitary waves, simulated using a spectral method, is found to be inelastic. It is found that the amplitude of the solitary waves changes slightly after the collision. The phase shifts these solitary waves undergo was calculated numerically.

Sepulveda, Nicasio↗
NASA NTRS1987

Time dependent boundary conditions for hyperbolic systems

Nonreflecting boundary conditions are defined for multidimensional fluid dynamics problems where waves enter and leave the interior of a domain modeled by hyperbolic equations. Separate equations are defined for each type of incoming and outgoing wave. Temporally varying problems are considered in terms of a nonreflecting boundary condition which permit the amplitude of incoming waves to remain constant over time. Conservative expressions are presented that include dissipative terms. Applications of the computational techniques are illustrated with sample results for a traveling shock wave, a shock tube, a spherical explosion and expansion problems on one- and two-dimensions.

Thompson, Kevin W.↗
NASA NTRS1994

Computations of drop collision and coalescence

Computations of drops collision and coalescence are presented. The computations are made possible by a recently developed finite difference/front tracking technique that allows direct solutions of the Navier-Stokes equations for a multi-fluid system with complex, unsteady internal boundaries. This method has been used to examine the boundaries between the various collision modes for drops of equal size and two examples, one of a 'reflective' collision and another of a 'grazing' collision is shown. From drops of unequal size, coalescence can result in considerable mixing between the fluid from the small and the large drop. This problem is discussed and one example showed. In many cases it is necessary to account also for heat transfer along with the fluid mechanics. We show two preliminary results where we are using extensions of the method to simulate such a problem. One example shows pattern formation among many drops moving due to thermal migration, the other shows unstable evolution of a solidification front.

Tryggvason, Gretar↗