Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast Fourier Transform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Feedforward-feedback ammonia control at a water resource recovery facility based on a digital twin with hybrid model

Ammonia-based aeration control (ABAC) at full-scale Water Resource Recovery Facilities (WRRFs) can be challenged by diurnal loading and transport delays. This work addressed these challenges using a hybrid feedforward–feedback controller built on Activated Sludge Model 1 (ASM1), marking the first full-scale deployment to pair a mechanistic feedforward core with data-driven corrections. The objectives were to improve ammonia setpoint tracking, assess performance of the mechanistic model when enhanced with data-driven corrections, and document full-scale operation. The hybrid model incorporates two data-driven components: (1) a Mechanistic Error Forecasting Engine (MEFE), consisting of a multivariate linear regressor and a long short-term memory (LSTM) ensemble. Defying expectations, low-parameter models outperformed more complex alternatives, reducing the mechanistic error by 71%. (2) A Residual Oscillation Forecasting Engine (ROFE), based on Fast Fourier Transform, reduced the remaining error by another 35%. Two proportional–integral (PI) feedback loops further (i) trim the feedforward output and (ii) eliminate residual controller error in the final aerobic zone. In full-scale operation, the controller reduced mean-squared error (MSE) by 94% over the baseline and produced more stable dissolved oxygen (DO) setpoints. Overall, it was proven that layering multi-timescale data-driven models on a mechanistic core can yield reliable ABAC performance at WRRFs.

54 ENVIRONMENTAL SCIENCES↗

Deposition of metallic gallium on re-crystallized ceramic material during focused ion beam milling

We report a new kind of artifact observed in the preparation of a TEM sample of zirconia by FIB, which consists in the deposition of metallic gallium nano-dots on the TEM sample surface. High resolution TEM images showed a microstructure of fine equiaxed grains of ∼ 5 nm, with some of them possessing two particular characteristics: high contrast and well-defined fast Fourier transform. These grains could not be identified as any phase of zirconia but it was possible to identify them as gallium crystals in the zone axis [110]. Based on HRTEM simulations, the possible orientations between zirconia substrate and deposited gallium are discussed in terms of lattice mismatch and oxygen affinity. - Highlights: • We show a new type of artifact induced during preparation of TEM samples by FIB. • Deposition of Ga occurs due to its high affinity for oxygen. • Materials with small grain size (∼ 5 nm) could promote Ga deposition. • Small grain size permits the elastic accommodation of deposited Ga.

36 MATERIALS SCIENCE↗

Advanced morphological analysis of patterns of thin anodic porous alumina

Different conditions of fabrication of thin anodic porous alumina on glass substrates have been explored, obtaining two sets of samples with varying pore density and porosity, respectively. The patterns of pores have been imaged by high resolution scanning electron microscopy and analyzed by innovative methods. The regularity ratio has been extracted from radial profiles of the fast Fourier transforms of the images. Additionally, the Minkowski measures have been calculated. It was first observed that the regularity ratio averaged across all directions is properly corrected by the coefficient previously determined in the literature. Furthermore, the angularly averaged regularity ratio for the thin porous alumina made during short single-step anodizations is lower than that of hexagonal patterns of pores as for thick porous alumina from aluminum electropolishing and two-step anodization. Therefore, the regularity ratio represents a reliable measure of pattern order. At the same time, the lower angular spread of the regularity ratio shows that disordered porous alumina is more isotropic. Within each set, when changing either pore density or porosity, both regularity and isotropy remain rather constant, showing consistent fabrication quality of the experimental patterns. Minor deviations are tentatively discussed with the aid of the Minkowski measures, and the slight decrease in both regularity and isotropy for the final data-points of the porosity set is ascribed to excess pore opening and consequent pore merging. - Highlights: • Thin porous alumina is partly self-ordered and pattern analysis is required. • Regularity ratio is often misused: we fix the averaging and consider its spread. • We also apply the mathematical tool of Minkowski measures, new in this field. • Regularity ratio shows pattern isotropy and Minkowski helps in assessment. • General agreement with perfect artificial patterns confirms the good manufacturing.

36 MATERIALS SCIENCE↗

Characterization of oxide scales grown on alloy 310S stainless steel after long term exposure to supercritical water at 500 °C

The oxide scale grown of static capsules made of alloy 310S stainless steel was investigated by exposure to the supercritical water at 500 °C 25 MPa for various exposure times up to 20,000 h. Characterization techniques such as X-ray diffraction, scanning/transmission electron microscopy, energy dispersive spectroscopy, and fast Fourier transformation were employed on the oxide scales. The elemental and phase analyses indicated that long term exposure to the SCW resulted in the formation of scales identified as Fe{sub 3}O{sub 4} (outer layer), Fe-Cr spinel (inner layer), Cr{sub 2}O{sub 3} (transition layer) on the substrate, and Ni-enrichment (chrome depleted region) in the alloy 310S. It was found that the layer thickness and weight gain vs. exposure time followed parabolic law. The oxidation mechanism and scales grown on the alloy 310S stainless steel exposed to SCW are discussed. - Highlights: •Oxidation of alloy 310S stainless steel exposed to SCW (500 °C/25 MPa) •The layer thickness and weight gain vs. exposure time followed parabolic law. •Oxide layers including Fe{sub 3}O{sub 4} (outer), Fe-Cr spinel (inner) and Cr{sub 2}O{sub 3} (transition) •Ni element is segregated by the selective oxidation of Cr.

36 MATERIALS SCIENCE↗

Preparation and characterization of biodegradable Mg-Zn-Ca/MgO nanocomposites for biomedical applications

Highlights: • Novel biodegradable Mg-Zn-Ca/MgO matrix composites, were devised and prepared using high shear melt conditioning. • The excellent interfacial bonding between MgO particles and α-Mg matrix was observed via HRTEM and FFT pattern analysis. • The optimum solution treatment and the addition of MgO nanoparticles hugely enhanced corrosion resistance of nanocomposites. • The yield tensile strength (YTS) increased by 22.81% with 0.5% MgO addition, while the ductility did not mainly deteriorate. - Abstract: In order to improve the corrosion resistance and mechanical properties of magnesium alloys for biomedical implant applications, novel biodegradable Mg-3Zn-0.2Ca (wt%) matrix composites, reinforced by adding various contents of MgO nanoparticles (0.1, 0.2, 0.3, 0.5 wt%), were devised and prepared using high shear melt conditioning. An optimum solution treatment (450 °C, 48 h) and subsequent hot extrusion was carried out to produce the Mg-3Zn-0.2Ca/MgO composites. It was found that the as-extruded composite exhibited a fine grain structure with relatively uniformly distributed MgO particles. The orientation relationships (ORs) of (1 1 1){sub MgO} ~ 2.62° from (0 0 0 2){sub α-Mg} and [0 −1 1]{sub MgO} // [2 −1 −1 0]{sub α-Mg}, were observed between the MgO particles and the α-Mg matrix via high resolution transmission electron microscopy (HRTEM) investigation and fast Fourier transform (FFT) pattern analysis, verifying the excellent interfacial bonding between the phases. Additionally, a substantial reduction in the secondary phase content was found in the solution treated sample. In vitro immersion, electrochemical, and mechanical tensile tests were used to characterize the corrosion behavior and mechanical properties. The ultimate tensile strength (UTS) increased to 329.03 ± 2.01 MPa and the yield tensile strength (YTS) increased by 22.81% with 0.5 wt% MgO loading, while the ductility did not substantially deteriorate. The polarization resistance (R{sub p}) of the composite was shown to increase from 0.95 kΩ cm{sup 2} to 2.02 kΩ cm{sup 2} with the addition of 0.2 wt% MgO. With increasing MgO content, agglomeration of the MgO particles was detected in the analyzed composite, resulting in decreased ductility and the occurrence of pitting corrosion.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Fourier-informed knot placement schemes for B-spline approximation

Fitting B-splines to scientific data is especially challenging when the given data contain noise, jumps, or corners. Here, we describe how periodic data sets with these features can be efficiently approximated with B-splines by analyzing the Fourier spectrum of the data. Our method uses a collection of spectral filters to compute high-order derivatives, smoothed versions of noisy data, and the locations of jump discontinuities. Further, these quantities are then combined to choose knots that capture the qualitative features of the data, leading to accurate B-spline approximations with few knots. The method we introduce is direct and does not require any intermediate B-spline fitting before choosing the final knot distribution. Aside from fast Fourier transforms to transfer to and from Fourier space, the method runs in linear time with very little communication. We assess performance on several test cases in one and two dimensions, including data sets with jump discontinuities and noise. These tests show the method fits discontinuous data without spurious oscillations and remains effective in the presence of noise.

97 MATHEMATICS AND COMPUTING↗

New large-strain FFT-based formulation and its application to model strain localization in nano-metallic laminates and other strongly anisotropic crystalline materials

This paper presents a new robust large-strain (LS) elasto-viscoplastic (EVP) formulation based on Fast Fourier Transforms (FFTs) for the prediction of the micro-mechanical response and microstructure evolution of polycrystalline and multiphase materials, with emphasis on the effect of strong crystallographic and/or morphologic anisotropy on localization of plastic deformation. In this work, the novel LS-EVPFFT formulation allows treatment of complex initial geometries and large deformations considering three grids of material points: a regular grid in the reference configuration, where FFTs can be performed; an irregular grid in the initial configuration, created by applying a stress-free displacement field to the reference regular grid; and an irregular grid in the current configuration, undergoing large strains and rotations as the material is loaded. Further numerical stability of the new formulation also required the use of a novel expression for the discrete modified Green’s operator, which reduces spurious field oscillations. After presenting and validating the new formulation by comparison with preexisting implementations and analytical solutions, LS-EVPFFT is applied to the prediction of slip and kink bands formation in polycrystalline columnar ice, and kink bands in single crystal zinc wires, showing good agreement with classic experiments. Finally, the model is used to study kink band formation during compression of Cu–Nb nano-metallic laminates (NMLs), in which accurate treatment of the complex geometry associated with the tortuosity of interfaces and large deformations become critical, showing consistency with corresponding micropillar experiments.

36 MATERIALS SCIENCE↗

Role of alloying elements on twin growth and twin transmission in magnesium alloys

A spatially-resolved crystal plasticity Fast Fourier Transform (FFT)-based model is employed to study the effect of alloying addition on twin thickening and twin transmission in hexagonal close packed (HCP) magnesium. In the simulations, the influence of alloying additions is represented through the differences in the critical resolved shear stress (CRSS) of different slip and twinning modes. The results show that for the same grain orientation, twin type and boundary conditions, anisotropy in the CRSS values have a significant effect on twin thickening and twin transmission. Those with large differences in CRSS favor both twin thickening and twin transmission, and vice versa for those with small differences. Furthermore, less difference among the CRSS values enhances the dependence of thickening and transmission on the neighboring grain orientation.

36 MATERIALS SCIENCE↗

The effects of free surfaces on deformation twinning in HCP metals

Deformation twinning is a predominant mode of plastic deformation for hexagonal close packed metals, like Mg and Ti. The heterogenous microstructure and the local stresses associated with twinning play a key role in their mechanical response and fracture. Surface analyses, like electron microscopy, are frequently employed to spatially map microstructure and micromechanical fields in order to study twinning behavior. However, these measurements are inherently influenced by the vicinity of the free surface. In this work, an elasto-visco-plastic fast-Fourier-transform (EVP-FFT) polycrystal modeling approach is employed to investigate the effects of free surfaces on twin development before and after loading. We compare calculated micromechanical fields on free surfaces with those calculated inside the bulk and, in some cases, experimental surface measurements. The results indicate that the creation of free surfaces can promote twin propagation and growth and can influence twin morphology by causing a twin lamella to become larger, more blunted and irregular. The structure along the twin boundaries are also affected, due to the higher driving stresses that extend prismatic-basal and basal-prismatic facets. Furthermore, free surfaces invoke different slip activities in the twin and the surrounding parent crystal by enhancing basal, prismatic and pyramidal slip in some localized regions, while reducing slip in others. We demonstrate that the simulated free-surface effects lead to better qualitative and quantitative agreement with experimental measurements from scanning electron microscopy and digital image correlation.

36 MATERIALS SCIENCE↗

Twinning pathways enabled by precipitates in $\mathrm{AZ91}$

While precipitates have been shown to substantially strengthen magnesium alloys by blocking the glide of dislocations inside the grain, the interactions between these precipitates and deformation twins, which commonly occur in these alloys, are much less understood. Here, in this work, an elasto-viscoplastic fast-Fourier-transform (EVP-FFT) model is used to study the interactions between plate-shaped basal precipitates and propagating $10\bar{1}2$ tensile twins in AZ91 Mg alloy. The results suggest that while precipitates may impede the propagation and thickening of twins, they can also cause stress localizations that can promote the formation of multiple new twins of the same or different crystallographic variants. We show that the location of the twin-precipitate interaction site, whether precipitate-central or precipitate-edge impingement, and the thickness of the precipitate can influence the propensity for twins to expand around the precipitate or nucleate a new twin on the other side of it. Depending on the twin-precipitate impingement site, we propose multiple twinning pathways that can help explain how twins can proliferate in the magnesium alloys in the presence of precipitates.

36 MATERIALS SCIENCE↗

Investigation of thermal hydraulic behavior of the High Temperature Test Facility's lower plenum via large eddy simulation

A high-fidelity computational fluid dynamics (CFD) analysis was performed using the Large Eddy Simulation (LES) model for the lower plenum of the High–Temperature Test Facility (HTTF), a ¼ scale test facility of the modular high temperature gas-cooled reactor (MHTGR) managed by Oregon State University. In most next–generation nuclear reactors, thermal stress due to thermal striping is one of the risks to be curiously considered. This is also true for HTGRs, especially since the exhaust helium gas temperature is high. In order to evaluate these risks and performance, organizations in the United States led by the OECD NEA are conducting a thermal hydraulic code benchmark for HTGR, and the test facility used for this benchmark is HTTF. HTTF can perform experiments in both normal and accident situations and provide high-quality experimental data. However, it is difficult to provide sufficient data for benchmarking through experiments, and there is a problem with the reliability of CFD analysis results based on Reynolds–averaged Navier–Stokes to analyze thermal hydraulic behavior without verification. To solve this problem, high-fidelity 3-D CFD analysis was performed using the LES model for HTTF. It was also verified that the LES model can properly simulate this jet mixing phenomenon via a unit cell test that provides experimental information. As a result of CFD analysis, the lower the dependency of the sub-grid scale model, the closer to the actual analysis result. In the case of unit cell test CFD analysis and HTTF CFD analysis, the volume-averaged sub-grid scale model dependency was calculated to be 13.0% and 9.16%, respectively. As a result of HTTF analysis, quantitative data of the fluid inside the HTTF lower plenum was provided in this paper. As a result of qualitative analysis, the temperature was highest at the center of the lower plenum, while the temperature fluctuation was highest near the edge of the lower plenum wall. The power spectral density of temperature was analyzed via fast Fourier transform (FFT) for specific points on the center and side of the lower plenum. FFT results did not reveal specific frequency-dominant temperature fluctuations in the center part. It was confirmed that the temperature power spectral density (PSD) at the top increased from the center to the wake. The vortex was visualized using the well-known scalar Q-criterion, and as a result, the closer to the outlet duct, the greater the influence of the mainstream, so that the inflow jet vortex was dissipated and mixed at the top of the lower plenum. Additionally, FFT analysis was performed on the support structure near the corner of the lower plenum with large temperature fluctuations, and as a result, it was confirmed that the temperature fluctuation of the flow did not have a significant effect near the corner wall. In addition, the vortices generated from the lower plenum to the outlet duct were identified in this paper. It is considered that the quantitative and qualitative results presented in this paper will serve as reference data for the benchmark.

97 MATHEMATICS AND COMPUTING↗

Validating simulated mountain wave impacts on hub-height wind speed using SoDAR observations

The ascent of stably stratified air over a mountain barrier can trigger the generation of mountain waves. Mountain waves occur frequently over the Columbia River Gorge in western North America and can impact wind power generation over the area. Therefore, predicting the details of mountain waves events (e.g., dominant wavelength, timing, and duration) can be very valuable for the wind energy community. In this study, the ability of the Weather Research and Forecasting (WRF) model to simulate mountain waves and their impact on hub-height wind speed is investigated. Our results suggest that the WRF model has moderate skill in simulating observed mountain wave. Further, given WRF predictions of wavelength range and wave period, the Fast Fourier Transform can calculate the simulated mountain wave impact on hub-height wind speed. The resulting wind speeds agree well with SoDAR observations in terms of both magnitude and pattern. Finally, for the simulated cases, WRF consistently predicts impacts of significant mountain wave events about an hour earlier than the actual observations. Overall, in this work, the sensitivities as well as uncertainties associated with our methodology are discussed in detail.

17 WIND ENERGY↗

Facile alignment estimation in carbon nanotube films using image processing

Whether a macroscopic assembly of carbon nanotubes can exhibit the one-dimensional properties expected from individual nanotubes critically depends on how well the nanotubes are aligned inside the assembly. Therefore, a simple and accurate method for assessing the degree of alignment is desired for the rapid characterization of carbon nanotube films and fibers. Here, we present an end-to-end solution for determining the global and local spatial orientation of carbon nanotubes in films within a short amount of time using a fast, precise, and economical approach based on an image processing method applied to scanning electron microscopy images. Further, we first use Laplacian edge enhancement filtering for improving the appearance of edge regions, which is followed by image partitioning into multiple blocks to capture the nanoscale orientation characteristics and total variation-based image decomposition of these image blocks. We then perform a 2D-fast Fourier transform on the image decomposed textural components of these edge-enhanced image blocks to determine the orientation distribution, which is utilized to estimate the 2D nematic order parameter. To show the effectiveness of our method, we corroborated our results against results obtained with other state-of-the-art image processing and experimental techniques.

2D-FFT↗

The effect of contact severity on micropitting: Simulation and experiments

In this work, a numerical contact fatigue model combining the effects of rolling contact fatigue and wear has been developed based on mixed elastohydrodynamic lubrication (EHL) theory, continuum damage mechanics (CDM) and the Archard's wear law. A series of benchtop tests were conducted using a triple-contact test rig to study the influence of surface roughness, speed and load on micropitting. The proposed surface damage model was used to simulate the rolling-sliding line contact of surfaces having different surface topography. The film thickness, contact pressure and sub-surface stress were determined by solving the generalized Reynolds equation and using the well-developed discrete convolute and fast Fourier transformation (DC-FFT) method. The jump-in-cycle was assumed to evaluate the accumulated damage based on the tested fatigue life and sub-surface stress histories. Surface topography was updated by calculating the wear height with the Archard's wear equation. Results reveal that micropitting occurs under the combined effect of wear and contact fatigue. The micropitting rate increased then turn to decreased as the lambda ratio (lambda) increased. The contact pressure significantly affected the contact fatigue life and the micropitting rate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrogen Storage Performance of Preferentially Oriented Mg/rGO Hybrids

Chemical interactions on the surface of a functional nanoparticle are closely related to its crystal facets, which can regulate the corresponding energy storage properties like hydrogen absorption. In this study, we reported a one-step growth of magnesium (Mg) particles with both close- and nonclose-packed facets, that is, {0001} and {$2\overline{116}$} planes, on atomically thin reduced graphene oxide (rGO). The detailed microstructures of Mg/rGO hybrids were revealed by X-ray diffraction, selected-area electron diffraction, high-resolution transmission electron microscopy, and fast Fourier transform analysis. Hydrogen storage performance of Mg/rGO hybrids with different orientations varies: Mg with preferential high-index {$2\overline{116}$} crystal surface shows remarkably increased hydrogen absorption up to 6.2 wt % compared with the system exposing no preferentially oriented crystal surfaces showing inferior performance of 5.1 wt % within the first 2 h. First-principles calculations revealed improved hydrogen sorption properties on the {$2\overline{116}$} surface with a lower hydrogen dissociation energy barrier and higher stability of hydrogen atoms than those on the {0001} basal plane, supporting the hydrogen uptake experiment. In addition, the hydrogen penetration energy barrier is found to be much lower than that of {0001} because of low surface atom packing density, which might be the most critical process to the hydrogenation kinetics. Here, the experimental and calculation results present a new handle for regulating the hydrogen storage of metal hydrides by controlled Mg facets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Petascale Orbital-Free Density Functional Theory Enabled by Small-Box Algorithms

Orbital-free density functional theory (OFDFT) is a quantum-mechanics-based method that utilizes electron density as its sole variable. The main computational cost in OFDFT is the ubiquitous use of the fast Fourier transform (FFT), which is mainly adopted to evaluate the kinetic energy density functional (KEDF) and electron–electron Coulomb interaction terms. We design and implement a small-box FFT (SBFFT) algorithm to overcome the parallelization limitations of conventional FFT algorithms. We also propose real-space truncation of the nonlocal Wang–Teter KEDF kernel. The scalability of the SBFFT is demonstrated by efficiently simulating one full optimization step (electron density, energies, forces, and stresses) of 1,024,000 lithium (Li) atoms on up to 65,536 cores. We perform other tests using Li as a test material, including calculations of physical properties of different phases of bulk Li, geometry optimizations of nanocrystalline Li, and molecular dynamics simulations of liquid Li. All of the tests yield excellent agreement with the original OFDFT results, suggesting that the OFDFT-SBFFT algorithm opens the door to efficient first-principles simulations of materials containing millions of atoms.

Chemistry↗

Correction to “Frank–Kasper Phases of Diblock Copolymer Melts Studied with the DPD Model: SCF Results”

In a recent study, (1) we performed the self-consistent field (SCF) calculations of a dissipative particle dynamics (DPD) model of conformationally asymmetric diblock copolymer A-B melts to study the stability of various Frank–Kasper (FK) phases formed by such A-B melts. While all the equations in ref (1) are correct, we did not calculate the dimensionless (mean-field) Helmholtz free energies per chain βf c = βu c,χ + βu c,κ – s c /k B and the dimensionless stresses dβf c /dθ of ordered phases accurately. For example, the dimensionless (nonbonded) internal energy per chain due to the system compressibility βu c,κ = (N/2κ)∑ q βû 0 (|q|)(ϕ̂ A (q) + ϕ̂ B (q) – δ q,0 )(ϕ̂ A (−q) + ϕ̂ B (−q) – δ– q,0 ) should be calculated in the reciprocal space as given (note that βû 0 (|q|) is obtained analytically, and that since ϕ A (r) is real 𝜙̂ A (−𝐪)= $\overline{𝜙̂ A}$(𝐪), i.e., the complex conjugate of ϕ̂ A (q)); this corresponds to numerically evaluating βu c,κ = (N/2κ)∫dr(ϕ A (r) + ϕ B (r) – 1)ψ(r) with ψ(r) ≡ (∫dr′βu 0 (|r–r′|)(ϕ A (r′) + ϕ B (r′) – 1)/V in the real space via the (composite) trapezoidal rule. While the trapezoidal rule is less accurate than the Romberg integration (2) in general, the opposite occurs when the integration domain is periodic; this was pointed out by Matsen in ref (3) and explained in detail in refs (4and5). With our ignorance of this exceptional convergence property of the trapezoidal rule for periodic functions, we calculated all convolutions having the form of ψ(r) in the reciprocal space via the fast Fourier transforms (6) but those having the form of βu c,κ in the real space via Romberg integration; the latter leads to inaccurate results and unfortunately incorrect phase diagrams reported in ref (1), which are corrected here.

He, Juntong↗