Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast Pyrolysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Deactivation of Multilayered MFI Nanosheet Zeolite during Upgrading of Biomass Pyrolysis Vapors

Here, the catalytic fast pyrolysis (CFP) of biomass is a promising technology for producing renewable transportation fuels and chemicals. MFI-type catalysts have shown promise for CFP because they produce gasoline range hydrocarbons from oxygenated pyrolysis compounds; however, rapid catalyst deactivation due to coking is one of the major technical barriers inhibiting the commercialization of this technology. Coke deposited on the surface of the catalysts blocks access to active sites in the micropores leading to rapid catalyst deactivation. Our strategy is to minimize rapid catalyst deactivation by adding mesoporosity through forming MFI nanosheet materials. The synthesized MFI nanosheet catalysts were fully characterized and evaluated for cellulose pyrolysis vapor upgrading to produce olefins and aromatic hydrocarbons. The data obtained from pyrolysis-GCMS (py-GCMS), showed that fresh MFI nanosheets produced similar aromatic hydrocarbon and olefin yields compared to conventional HZSM-5. However, MFI nanosheets demonstrated a longer lifetime than HZSM-5 even though coke contents were also higher than for HZSM-5 because the mesopores enabled better accessibility to active acid sites. This conclusion was supported by results from post-reaction analysis of various spent catalysts collected at different points during the deactivation experiments.

09 BIOMASS FUELS↗

A review of thermochemical upgrading of pyrolysis bio‐oil: Techno‐economic analysis, life cycle assessment, and technology readiness

Abstract Technologies for upgrading fast pyrolysis bio‐oil to drop‐in fuels and coproducts are under development and show promise for decarbonizing energy supply for transportation and chemicals markets. The successful commercialization of these fuels and the technologies deployed to produce them depend on production costs, scalability, and yield. To meet environmental regulations, pyrolysis‐based biofuels need to adhere to life cycle greenhouse gas intensity standards relative to their petroleum‐based counterparts. We review literature on fast pyrolysis bio‐oil upgrading and explore key metrics that influence their commercial viability through life cycle assessment (LCA) and techno‐economic analysis (TEA) methods together with technology readiness level (TRL) evaluation. We investigate the trade‐offs among economic, environmental, and technological metrics derived from these methods for individual technologies as a means of understanding their nearness to commercialization. Although the technologies reviewed have not attained commercial investment, some have been pilot tested. Predicting the projected performance at scale‐up through models can, with industrial experience, guide decision‐making to competitively meet energy policy goals. LCA and TEA methods that ensure consistent and reproducible models at a given TRL are needed to compare alternative technologies. This study highlights the importance of integrated analysis of multiple economic, environmental, and technological metrics for understanding performance prospects and barriers among early stage technologies.

09 BIOMASS FUELS↗

CFD-DEM Modeling of Autothermal Pyrolysis of Corn Stover with a Coupled Particle- and Reactor-Scale Framework

Autothermal operation of fast pyrolysis is an efficient process-intensification technique wherein exothermic oxidation reactions are used to overcome the heat-transfer bottleneck of conventional pyrolysis. The development of accurate, reliable modeling toolsets is imperative to generating a deeper understanding of biomass autothermal pyrolysis systems to support scale-up and industrial deployment. This modeling effort describes the development of single-particle and reactor models which incorporate detailed reaction schemes and simultaneous exothermic oxidation reactions. The particle-scale model was parameterized for corn stover feedstock with particle morphology, density, ash content, and biopolymer composition, all of which impact the emergent conversion characteristics during pyrolysis. Results were then used to parameterize a reactor-scale autothermal pyrolysis model, which was developed using a coarse-grained computational fluid dynamic-discrete element method. The simulation results compared well with experimental results, with the predicted bio-oil, light gas, and biochar yield within 3.0 wt% of the experimental yields. Further analyses were performed to test the influence of equivalence ratio, biomass injection position, and particle size distribution on autothermal pyrolysis. The analysis of the physio-chemical properties of the fluid and solid phase inside the reactor and at the reactor outlet help reveal important process interactions of autothermal pyrolysis.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗

Pilot-Scale Biorefinery: Sustainable Transport Fuels from Biomass via Integrated Pyrolysis and Catalytic Hydroconversion - Wastewater Cleanup by Catalytic Hydrothermal Gasification

DOE-EE Bioenergy Technologies Office has set forth several goals to increase the use of bioenergy and bioproducts derived from renewable resources. One of these goals is to facilitate the implementation of the biorefinery. The biorefinery will include the production of liquid fuels, power and, in some cases, products. The integrated biorefinery should stand-alone from an economic perspective with fuels and power driving the economy of scale while the economics/profitability of the facility will be dependent on existing market conditions. UOP LLC proposed to demonstrate a fast pyrolysis based integrated biorefinery. Pacific Northwest National Laboratory (PNNL) has expertise in an important technology area of interest to UOP for use in their pyrolysis-based biorefinery. This CRADA project provides the supporting technology development and demonstration to allow incorporation of this technology into the biorefinery. PNNL developed catalytic hydrothermal gasification (CHG) for use with aqueous streams within the pyrolysis biorefinery. These aqueous streams included the aqueous phase separated from the fast pyrolysis bio-oil and the aqueous byproduct streams formed in the hydroprocessing of the bio-oil to finished products. The purpose of this project was to demonstrate a technically and economically viable technology for converting renewable biomass feedstocks to sustainable and fungible transportation fuels. To demonstrate the technology, UOP constructed and operated a pilot-scale biorefinery that processed one dry ton per day of biomass using fast pyrolysis. Specific objectives of the project were to: The anticipated outcomes of the project were a validated process technology, a range of validated feedstocks, product property and Life Cycle data, and technical and operating data upon which to base the design of a full-scale biorefinery. The anticipated long-term outcomes from successful commercialization of the technology were: (1) the replacement of a significant fraction of petroleum based fuels with advanced biofuels, leading to increased energy security and decreased carbon footprint; and (2) establishment of a new biofuel industry segment, leading to the creation of U.S. engineering, manufacturing, construction, operations and agricultural jobs. PNNL development of CHG progressed at two levels. Initial tests were made in the laboratory in both mini-scale and bench-scale continuous flow reactor systems. Following positive results, the next level of evaluation was in the scaled-up engineering development system, which was operated at PNNL.

09 BIOMASS FUELS↗

Comparative Techno-Economic Analysis of Available Feedstocks for High-Temperature Conversion: Whole Tree Thinnings and Mature Pine Residues

The techno-economic and life cycle implications of utilizing low-cost feedstocks in a high temperature conversion process are of great interest. Here, we investigate the conversion cost impacts of two underutilized feedstocks from the commercial pine industry: 13-year-old whole trees, representing trees removed for the purpose of precommercial thinning, and 23-year-old pine residues, representing a waste stream produced from the deconstruction of mature trees for other purposes. Experimental fast pyrolysis (FP) yields for each feedstock were adjusted to a catalytic fast pyrolysis (CFP) basis and used to estimate process economics by employing published correlations based on rigorous techno-economic modeling. These correlations were used in tandem with results from supply and preprocessing analyses to evaluate the field-to-fuel economics of each feedstock. A small difference in minimum fuel selling price (MFSP) was found between the conversion costs for the two feedstocks, with 23-year-old residues demonstrating a net benefit of $0.27 per gasoline gallon equivalent (GGE) compared to the 13- year-old whole tree thinnings, driven primarily by feedstock supply costs. This suggests that both whole tree thinnings and pine residues may be viable feedstock options for CFP conversion. Life cycle inventories (LCIs) were also generated for each case, enabling a field-to-fuel quantification of the cost and carbon cycle associated with each feedstock.

catalytic fast pyrolysis↗

110th Anniversary: Microkinetic Modeling of the Vapor Phase Upgrading of Biomass-Derived Oxygenates

Bio-oil produced from fast pyrolysis of biomass is a complex mixture of more than 200 compounds, including oxygenates and acids. As these species are highly undesirable in fuels, catalytic upgrading of biomass pyrolysis product vapors, also known as catalytic fast pyrolysis, is performed to upgrade the vapors to valuable fuels and chemicals. This work presents a detailed microkinetic model, composed of elementary steps, of the catalytic upgrading of acetic acid and acetone, two common oxygenates present in bio-oil. An automated network generator was utilized to construct a reaction network composed of 580 unique species and 2160 unique reactions. The kinetic parameters for each reaction in the network were estimated using transition state theory, the Evans-Polanyi relationship, and thermodynamic data. The resulting mechanistic model is able to describe experimental data presented in the literature for the transformation of acetic acid and acetone on HZSM-5 in a fixed-bed reactor, which is modeled as a plug-flow reactor. Additionally, the model solutions reveal vital information regarding the mechanism by which acetic acid and acetone are upgraded to valuable fuels and chemicals. In the first phase of the mechanism, acetic acid is converted to acetone via acylium ion addition to acetic acid; this is followed by decarboxylation of acetoacetic acid. The second phase is dominated by the self-aldol condensation of acetone, which is shown to occur predominantly through the keto form of acetone rather than the enol form, and subsequent deoxygenation reactions leading to olefins and aromatics. Finally, net rate analysis shows that aromatics are primarily formed via a pathway including aldol condensation of mesityl oxide, whereas olefins are produced from the addition of isobutene and subsequent cracking.

09 BIOMASS FUELS↗

Results of the International Energy Agency Bioenergy Round Robin on the Analysis of Heteroatoms in Biomass Liquefaction Oils

A round robin study evaluating the analysis of biomass liquefaction oils (BLOs) from fast pyrolysis and hydrothermal liquefaction (HTL) was performed, involving fifteen laboratories in seven countries in order to assess the current status of analytical techniques for the determination of nitrogen, sulfur, and chlorine content in BLOs and evaluate potential differences in origin (i.e. fast pyrolysis vs HTL). The BLOs were produced from a range of feedstocks including pine, mixed softwoods, forest residues, micro-algae, miscanthus, and wheat straw to cover a variety in nitrogen, sulfur, and chlorine content and speciation. Nine samples were distributed, comprised of eight separate BLOs and one blind duplicate produced by five producers. The samples were analyzed for water, carbon, hydrogen, nitrogen, sulfur, and chlorine content. No analytical test method was mandated; laboratories were encouraged to utilize whichever method they determined would be most applicable, relying on the existing body of BLO literature as a guide. The results of this round robin study are presented in this paper. The results of the carbon, hydrogen, and water measurements as reference analyses had relative standard deviations (2.9%, 3.5, and 5.6%, respectively) that were comparable to those found in past round robin studies on fast pyrolysis bio-oil. The analysis of nitrogen, sulfur, and chlorine showed higher levels of variability. Laboratories mostly chose the same method for water, carbon, hydrogen and nitrogen determination whereas there were a variety of methods chosen for sulfur and chlorine determination. The results suggest that specific analytical methods for the determination of nitrogen, sulfur, and chlorine should be further refined to ensure reproducible and accurate results for BLO analysis due to their importance on emissions, material selection, and catalyst activity.

Biomass, IEA Bioenergy, pyrolysis, hydrothermal li↗

The effect of clay catalyst on the chemical composition of bio-oil obtained by co-pyrolysis of cellulose and polyethylene

Highlights: • Non-catalytic and catalytic fast pyrolysis of cellulose/polyethylene blend was carried out in a laboratory scale reactor. • Optimization of process temperature was done. • Optimization of clay catalyst type and amount for co-pyrolysis of cellulose and polyethylene was done. • The product yields and the chemical composition of bio-oil was investigated. - Abstract: Cellulose/polyethylene (CPE) mixture 3:1, w/w with and without three clay catalysts (K10 – montmorillonite K10, KSF – montmorillonite KSF, B – Bentonite) addition were subjected to pyrolysis at temperatures 400, 450 and 500 °C with heating rate of 100 °C/s to produce bio-oil with high yield. The pyrolytic oil yield was in the range of 41.3–79.5 wt% depending on the temperature, the type and the amount of catalyst. The non-catalytic fast pyrolysis at 500 °C gives the highest yield of bio-oil (79.5 wt%). The higher temperature of catalytic pyrolysis of cellulose/polyethylene mixture the higher yield of bio-oil is. Contrarily, increasing amount of montmorillonite results in significant, almost linear decrease in bio-oil yield followed by a significant increase of gas yield. The addition of clay catalysts to CPE mixture has a various influence on the distribution of bio-oil components. The addition of montmorillonite K10 to cellulose/polyethylene mixture promotes the deepest conversion of polyethylene and cellulose. Additionally, more saturated than unsaturated hydrocarbons are present in resultant bio-oils. The proportion of liquid hydrocarbons is the highest when a montmorillonite K10 is acting as a catalyst.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Catalytic Upgrading of Biomass Pyrolysis Vapors at Bench Scale with Pt/TiO2

Vapor phase upgrading can produce a liquid of lower oxygen and higher energy density than can fast pyrolysis alone. Therefore, it is anticipated that catalytic pyrolysis followed by a single stage of hydrotreating will be a more cost-effective route to hydrocarbon fuels than fast pyrolysis with multiple-stage or more-severe hydrotreating. To this end, a bench-scale bubbling fluidized bed pyrolyzer was operated at 150 g/h feed rate of pine flour with a 100 g fixed-bed catalytic upgrader. A 0.5% Pt/TiO2 catalyst produced a lower oxygen (< 20%) liquid at 40% carbon efficiency at 400 degrees C and biomass-to-catalyst ratio (B:C) of 3 for numerous cycles. The catalyst was regenerated and reused by oxidation with air and reduction with hydrogen. The oxidation and reduction times were reduced to 2 h and 1 h respectively without compromising performance or catalyst temperature control. Increasing the pyrolysis temperature from 500 degrees C to 550 degrees C allowed operation at B:C greater than 3 at comparable performance. Performance was generally similar to 2% Pt/TiO2 but at reduced catalyst cost. Projected costs are < $4/gallon of gasoline blendstock. Responses to other parameter changes and prospects for further improvements will be discussed.

09 BIOMASS FUELS↗

Design, scaling and cost evaluations of circulating fluidized-bed systems for biomass pyrolysis

To generate updated and transparent capital cost estimates for biomass fast pyrolysis equipment, refinery fluidized catalytic cracking design and sizing principles are examined and extended to pyrolysis of woody biomass. Capital costs for the sized equipment are estimated with process-industry software. A one-dimensional flow simulation with pyrolysis kinetics is leveraged to validate the fluidization conditions and thermal energy balance. After successful sizing and a system cost estimate of $\$$2.8 M (in 2016 US$\$$) at the biorefinery scale of 1000 metric tons per day (MTD), these methods were exercised for even smaller equipment at the distributed pyrolysis scale with modifications to the process design constraints, and not directly comparable with the 1000 MTD case, arriving at capital cost estimates of $\$$1.2 M for a 500 ton/day system and $\$$0.9 M for a 200 ton/day system. Here in this work, It is noted that this work only estimates purchased equipment costs at the ±50% accuracy level; there are significant other custom factors applicable to each installation based on location, maturity, scale, complexities during installation, engineering and licensing costs, etc. that need to be added on to these estimates to derive investment costs.

09 BIOMASS FUELS↗

Predicting the Cetane Number, Yield Sooting Index, Kinematic Viscosity, and Cloud Point for Catalytically Upgraded Pyrolysis Oil Using Artificial Neural Networks

Abstract The conversion of biomass using fast pyrolysis has the potential to be significantly less expensive at scale compared to alternative methods such as fermentation and gasification. Selective upgrading of the products of fast pyrolysis through chemical catalysis produces compounds with lower oxygen content and lower acidity; however, identifying the specific catalytic pathways for producing viable fuels and fuel additives often requires a trial-and-error approach. Specifically, key properties of the compounds must be experimentally tested to evaluate the viability of the resultant compounds. The present work proposes predictive models constructed with artificial neural networks (ANNs) for cetane number (CN), yield sooting index (YSI), kinematic viscosity (KV), and cloud point (CP), with blind test set median absolute errors of 5.14 cetane units, 3.36 yield sooting index units, 0.07 millimeters squared per second, and 4.89 degrees Celsius, respectively. Furthermore, the cetane number, yield sooting index, kinematic viscosity, and cloud point were predicted for over three hundred expected products from the catalytic upgrading of pyrolysis oil. It was discovered that 130 of these compounds have predicted cetane numbers greater than 40, with four of these compounds possessing predicted yield sooting index values significantly less than that of diesel fuel and predicted viscosities and cloud points comparable to that of diesel fuel.

09 BIOMASS FUELS↗

Assessment of a Detailed Biomass Pyrolysis Kinetic Scheme in Multiscale Simulations of a Single-Particle Pyrolyzer and a Pilot-Scale Entrained Flow Pyrolyzer

A detailed biomass pyrolysis kinetic scheme was assessed in the multiscale simulations of a single-particle pyrolyzer with slow pyrolysis and a pilot-scale entrained flow pyrolyzer with fast pyrolysis. The detailed kinetic scheme of biomass pyrolysis developed by the CRECK group consists of 32 reactions and 58 species. A multiscale simulation model was developed, where the CRECK kinetics was employed to simulate biomass pyrolysis reactions, a one-dimensional particle model was utilized to simulate the intraparticle transport phenomena, and the particle-in-cell (PIC) model was employed to simulate the hydrodynamics. The multiscale model was first applied to simulate a single-particle pyrolysis experiment. The simulation with nonisothermal particles matched the experimental data better than the simulation with isothermal particles. Then the multiscale model was applied to simulate the pilot-scale entrained flow pyrolyzer. In this case, the simulation with isothermal particles matched the experimental data better than the simulation with nonisothermal particles. The reason for this difference might be that the kinetics itself already partially included the intraparticle transport effect as it was fitted using both TGA data (slow pyrolysis of small size biomass) and fluidized bed data (fast pyrolysis of relatively large size biomass). This study provides some insights into biomass pyrolysis kinetics development and pyrolyzer multiscale simulation for a future study.

09 BIOMASS FUELS↗

Catalytic Upgrading of Biomass Pyrolysis Vapors at Bench Scale with Platinum on Titania

Vapor phase upgrading can produce a liquid of lower oxygen and higher energy density than can fast pyrolysis alone. Therefore, it is anticipated that catalytic pyrolysis followed by a single stage of hydrotreating will be a more cost-effective route to hydrocarbon fuels than fast pyrolysis with multiple-stage or more-severe hydrotreating. To this end, a bench-scale bubbling fluidized bed pyrolyzer was operated at 150 g/h feed rate of pine flour with a 100 g fixed-bed catalytic upgrader. A 0.5% Pt/TiO2 catalyst produced a lower oxygen (< 20%) liquid at 40% carbon efficiency at 400 degrees C and biomass-to-catalyst ratio (B:C) of 3 for numerous cycles. The catalyst was regenerated and reused by oxidation with air and reduction with hydrogen. The oxidation and reduction times were reduced to 2 h and 1 h respectively without compromising performance or catalyst temperature control. Increasing the pyrolysis temperature from 500 degrees C to 550 degrees C allowed operation at B:C greater than 3 at comparable performance. Performance was generally similar to 2% Pt/TiO2 but at reduced catalyst cost. Projected costs are < $4/gallon of gasoline blendstock. Responses to other parameter changes and prospects for further improvements will be discussed.

09 BIOMASS FUELS↗

Conventional and autothermal pyrolysis of corn stover: Overcoming the processing challenges of high-ash agricultural residues

The high ash content of agricultural residues and other kinds of herbaceous biomass makes it a challenging feedstock for fast pyrolysis to bio-oil. Using corn stover as a representative feedstock, this study investigates fast pyrolysis of high ash, herbaceous biomass in a pilot-scale fluidized bed reactor using both conventional, nitrogen-blown and autothermal, air-blown operation. Initial efforts to pyrolyze corn stover were challenged by bed fouling, which prevented steady reactor operation. Substitution of coarser bed material allowed operation at higher superficial velocities, which promoted attrition and elutriation of recalcitrant biochar particles from the reactor. This resulted in dramatic improvement in stable reactor operation for both conventional and autothermal pyrolysis with bio-oil yields among the highest reported for pyrolysis of corn stover. The oxygen-to-biomass equivalence ratio required for autothermal operation was 6.8%. Autothermal operation also resulted in significant process intensification, increasing corn stover throughput from 7.8 kg hr –1 to 21.9 kg hr –1 for this 8.9 cm diameter reactor. Air-blown, autothermal operation did not significantly reduce bio-oil yield despite the presence of partial oxidation reactions. In conclusion, carbon balances indicate carbon yields of biochar and aqueous, bio-oil light ends decreased by 18.5% and 4.7%, respectively, during autothermal pyrolysis compared to conventional pyrolysis while the more valuable, organic-rich heavy ends of the bio-oil were essentially preserved.

09 BIOMASS FUELS↗

Biochar Collection Overview and Design Upgrades in Biomass Pyrolysis Pilot Plant

The Thermochemical Process Development Unit (TCPDU) at the National Renewable Energy Laboratory conducts research on a pilot plant that may be configured for biomass fast pyrolysis or gasification with the ultimate objective of creating renewable transportation fuels. Current research is focused on optimizing pyrolysis conditions for low-cost feedstock blends that are widely available and relevant on an industrial scale. Future research (2018) will focus on ex-situ catalytic upgrading of pyrolysis vapors using a riser reactor and regenerator system, similar to a fluid catalytic cracking system. The TCPDU is capable of feeding 1/2 ton of biomass per day and commonly operates at a feed rate of ~33 lb/h biomass while configured for fast pyrolysis. At this feed rate, the TCPDU generates ~2.2 gal/h of raw bio-oil and ~4.5lb/h of solid bio-char.

09 BIOMASS FUELS↗

Determination of Water Content in Bio-Oils by Volumetric Karl Fischer Titration: Laboratory Analytical Procedure (LAP)

The water content of bio-oils is a key metric for several reasons. Water is typically the most concentrated single component of fast pyrolysis oils, though this will be much lower in catalytic fast pyrolysis and upgraded products. Reduced water content is preferable in bio-oil as water can contribute to phase separation, corrosivity, and instability. Additionally, lower water is beneficial for physical properties such as energy density. The percentage of water can also be used to correct the calculation for organic oxygen when determining total oxygen content of bio-oils via combustion-based ultimate analysis. The procedure described here is specifically written for the analysis of bio-oils, and is based on ASTM E203, Standard Test Method for Water Using Volumetric Karl Fischer Titration. This standard test method is specified for measuring the mass % water in pyrolysis liquid biofuels in ASTM D7544, Standard Specification for Pyrolysis Liquid Biofuel. Although the standard method is prescribed for the analysis of pyrolysis liquids for use in industrial and commercial burners, the method is not specifically written for this product. The method described with this Laboratory Analytical Procedure (LAP) provides specific guidance for the analysis of bio-oils. Both organic and aqueous phases can be measured with this technique.

09 BIOMASS FUELS↗

Challenges and Opportunities for Bio-oil Refining: A Review

Bio-oil derived from fast pyrolysis of lignocellulosic materials is among the most complex and inexpensive raw oils that can be produced today. Although commercial or demonstration scale fast pyrolysis units can readily produce this oil, this industry has not grown to significant commercial impact due to the lack of bio-oil market pull. This paper is a review of the challenges and opportunities for bio-oil upgrading and refining. Pyrolysis oil consists of six major fractions. (water 15-30 wt.%, light oxygenates, 8-26 wt.%. mono-phenols, 2-7 wt.%, water insoluble oligomers derived from lignin 15-25wt.%, and water soluble havey molecules 10-30 wt.%). The composition of water-soluble oligomers is relatively poorly studied. In the 1880s, bio-oil refining (formally known as wood distillation) targeted the separation and commercialization of C1-C4 light oxygenated compounds to produce methanol, acetic acid and acetone with the commercialization of the lignin derived water insoluble fraction for preserving wooden sailing vessels against rot. More recently the company Ensyn extracted and commercialized condensed natural smoke as a food additive. Most research efforts in the last twenty years have focused on the two-step hydrotreatment concept for the production of transportation fuels. In spite of major progress this concept remains at the demonstration. In this review, the opportunities and progress to separate bio-oil fractions and chemicals, mainly acetic acid (HAc), hydroxyacetaldehyde (HHA) and acetol, and convert them into value added co-products are thoroughly discussed. In spite of the large number of separation schemes and products tested, very few of them have been studied as part of fully integrated bio-oil refinery concepts. Furthermore, the synthesis, techno-economic and environmental evaluation of novel integrated bio-oil refinery concepts is likely to become a subject of intense research activity in the coming years.

09 BIOMASS FUELS↗

Corrosivity Screening of Pyrolysis Bio-Oils by Short-Term Alloy Exposures. Laboratory Analytical Procedure (LAP), Issue Date: May 12, 2022

Bio-oils contain organic acids and oxygenated compounds that can lead to corrosion issues during bio-oil processing and storage. This Laboratory Analytical Procedure (LAP) allows for rapid screening of a bio-oil's corrosivity without the need for complex equipment and long-term exposures. A robust and repeatable method for assessing the corrosivity of bio-oils is necessary in order to remove materials degradation as an obstacle to research, upgrading, use and storage of bio-oils. This LAP involves the incubation of a representative alloy, 410 stainless steel (410 SS), specimen in bio-oil over a period of 48 hours at 50 degrees C in a sealed container. The corrosive species in the bio-oil react with and deplete alloy elements such as iron (Fe) and/or chromium (Cr) from the specimen into the bio-oil solution. The depletion of Fe and Cr from the specimen results in a significant mass loss that can be recorded. The mass loss is directly correlated to the corrosivity of a bio-oil. Examples of bio-oils in scope include the ones produced by fast pyrolysis and catalytic fast pyrolysis, as well as liquids produced from hydrothermal liquefaction.

09 BIOMASS FUELS↗