Results for “Freestream conditions” — Page 17

NASA NTRS1992

TranAir: A full-potential, solution-adaptive, rectangular grid code for predicting subsonic, transonic, and supersonic flows about arbitrary configurations. User's manual

The TranAir computer program calculates transonic flow about arbitrary configurations at subsonic, transonic, and supersonic freestream Mach numbers. TranAir solves the nonlinear full potential equations subject to a variety of boundary conditions modeling wakes, inlets, exhausts, porous walls, and impermeable surfaces. Regions with different total temperature and pressure can be represented. The user's manual describes how to run the TranAir program and its graphical support programs.

Johnson, F. T.↗

NASA NTRSDate not supplied

Some Effects of Tunnel Noise on Cylinder-Induced Mach 6 Transitional Shock Wave Boundary Layer Interactions

Experiments were conducted on a cylinder-induced shock wave boundary layer interaction (SBLI)as its state was brought through transition using a combination of boundary layer trips and Reynolds number sweep. A baseline case with no trips was also examined. The measurements were made in a Mach 6 freestream in the well-characterized Actively Controlled Expansion tunnel, which demonstrated a near tripling in fluctuation levels with unit Reynolds number increase from 3.0 to 3.5 million per meter. Surface oil flow and schlieren images suggested the jump in freestream noise served as the impetus for SBLI transition since the flow separation distance began to decrease as the Reynolds number progressed through those conditions. Likewise, surface mounted Kulite® pressure transducers indicated a rise in surface pressure fluctuations as well as initial growth in the instability responsible for transitioning the boundary layer within the interaction. Finally, heat transfer rates within the tripped SBLI were shown to be affected by the jump in freestream disturbance levels.

Andrew N Leidy↗

NASA NTRS2017

Computational Analysis of Powered Lift Augmentation for the LEAPTech Distributed Electric Propulsion Wing

A computational study of a distributed electric propulsion wing with a 40deg flap deflection has been completed using FUN3D. Two lift-augmentation power conditions were compared with the power-off configuration on the high-lift wing (40deg flap) at a 73 mph freestream flow and for a range of angles of attack from -5 degrees to 14 degrees. The computational study also included investigating the benefit of corotating versus counter-rotating propeller spin direction to powered-lift performance. The results indicate a large benefit in lift coefficient, over the entire range of angle of attack studied, by using corotating propellers that all spin counter to the wingtip vortex. For the landing condition, 73 mph, the unpowered 40deg flap configuration achieved a maximum lift coefficient of 2.3. With high-lift blowing the maximum lift coefficient increased to 5.61. Therefore, the lift augmentation is a factor of 2.4. Taking advantage of the fullspan lift augmentation at similar performance means that a wing powered with the distributed electric propulsion system requires only 42 percent of the wing area of the unpowered wing. This technology will allow wings to be 'cruise optimized', meaning that they will be able to fly closer to maximum lift over drag conditions at the design cruise speed of the aircraft.

Deere, Karen A.↗

NASA NTRS2004

Exhaust Simulation Testing of a Hypersonic Airbreathing Model at Transonic Speeds

An experimental study was performed to examine jet-effects for an airframe-integrated, scramjet-rocket combined-cycle vehicle configuration at transonic test conditions. This investigation was performed by testing an existing exhaust simulation wind tunnel model, known as Model 5B, in the NASA Langley 16-Ft. Transonic Tunnel. Tests were conducted at freestream Mach numbers from 0.7 to 1.2, at angles of attack from 2 to +14 degrees, and at up to seven nozzle static pressure ratio values for a set of horizontal-tail and body-flap deflections. The model aftbody, horizontal tails, and body flaps were extensively pressure instrumented to provide an understanding of jet-effects and control-surface/plume interactions, as well as for the development of analytical methodologies and calibration of computational fluid dynamic codes to predict this type of flow phenomenon. At all transonic test conditions examined, the exhaust flow at the exit of the internal nozzle was over-expanded, generating an exhaust plume that turned toward the aftbody. Pressure contour plots for the aftbody of Model 5B are presented for freestream transonic Mach numbers of 0.70, 0.95, and 1.20. These pressure data, along with shadowgraph images, indicated the impingement of an internal plume shock and at least one reflected shock onto the aftbody for all transonic conditions tested. These results also provided evidence of the highly three-dimensional nature of the aftbody exhaust flowfield. Parametric testing showed that angle-of-attack, static nozzle pressure ratio, and freestream Mach number all affected the exhaust-plume size, exhaust-flowfield shock structure, and the aftbody-pressure distribution, with Mach number having the largest effect. Integration of the aftbody pressure data showed large variations in the pitching moment throughout the transonic regime.

Huebner, Lawrence D.↗

NASA NTRSDate not supplied

Status of Mars Retropropulsion Testing in the Langley Unitary Plan Wind Tunnel

Future Mars human landings will be enabled by a powered descent phase starting at supersonic conditions, something which has never been done before on a Mars mission. Significant aerosciences challenges exist due to jet interactions between the retrorocket engine plumes, freestream flow, and vehicle that will affect the aerodynamic behavior during powered descent. Historically, wind tunnel tests have been used to study the interactions with inert gas exhaust simulants in place of rocket engines. On the computational side, flowfield simulations have been completed at full-scale conditions, but the available ground and flight data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles, due to insufficient data, dissimilar vehicle geometries, and disparate operating conditions. A wind tunnel test has been designed to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. The test will be conducted in the NASA Langley Unitary Plan Wind Tunnel and is designed with improvements in model design and data products over past tests. The test campaign will be run using sub-scale model geometries derived from NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry that generates higher unpowered lift. Both models have been fabricated and are ready for testing. The blunt model is equipped with the flexibility to examine the effects of nozzle pointing direction, number, location, size, and area ratio. The main measurements are heatshield aerodynamic interference forces and moments with a custom flow-through balance, discrete and distributed heatshield pressure, and high-speed flowfield visualization. This paper covers the test objectives, facility, models and instrumentation, and planned test matrix.

Mars↗

NASA NTRSDate not supplied

Status of Mars Retropropulsion Testing in the Langley Unitary Plan Wind Tunnel

Future Mars human landings will be enabled by a powered descent phase starting at supersonic conditions, something which has never been done before on a Mars mission. Significant aerosciences challenges exist due to jet interactions between the retrorocket engine plumes, freestream flow, and vehicle that will affect the aerodynamic behavior during powered descent. Historically, wind tunnel tests have been used to study the interactions with inert gas exhaust simulants in place of rocket engines. On the computational side, flowfield simulations have been completed at full-scale conditions, but the available ground and flight data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles, due to insufficient data, dissimilar vehicle geometries, and disparate operating conditions. A wind tunnel test has been designed to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. The test will be conducted in the NASA Langley Unitary Plan Wind Tunnel and is designed with improvements in model design and data products over past tests. The test campaign will be run using sub-scale model geometries derived from NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry that generates higher unpowered lift. Both models have been fabricated and are ready for testing. The blunt model is equipped with the flexibility to examine the effects of nozzle pointing direction, number, location, size, and area ratio. The main measurements are heatshield aerodynamic interference forces and moments with a custom flow-through balance, discrete and distributed heatshield pressure, and high-speed flowfield visualization. This paper covers the test objectives, facility, models and instrumentation, and planned test matrix.

Supersonic Retropropulsion↗

NASA NTRS2017

Stabilization of Hypersonic Boundary Layers by Linear and Nonlinear Optimal Perturbations

The effect of stationary, finite-amplitude, linear and nonlinear optimal perturbations on the modal disturbance growth in a Mach 6 axisymmetric flow over a 7 deg. half-angle cone with 0:126 mm nose radius and 0:305 m length is investigated. The freestream parameters (M = 6, Re(exp 1) = 18 x 10(exp. 6) /m) are selected to match the flow conditions of a previous experiment in the VKI H3 hypersonic tunnel. Plane-marching parabolized stability equations are used in conjunction with a partial-differential equation based planar eigenvalue analysis to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode and first-mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone; however, subharmonic first-mode instabilities, which are destabilized by the presence of the streaks, do reach N = 6 near the end of the cone. The highest stabilization is observed at streak amplitudes of approximately 20 percent of the freestream velocity. Because the use of initial disturbance profiles based on linear optimal growth theory may yield suboptimal control in the context of nonlinear streaks, the computational predictions are extended to nonlinear optimal growth theory. Results show that by using nonlinearly optimal perturbation leads to slightly enhanced stabilization of plane Mack mode disturbances as well as reduced destabilization of subharmonic first-mode disturbances.

Incompressible boundary layer↗

NASA NTRSDate not supplied

Hypersonic Boundary-Layer Transition over a Blunt Circular Cone in a Mach 8 Digital Wind Tunnel

To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, three-dimensional direct numerical simulations (DNS) were conducted to investigate the interaction of a tunnel-like acoustic disturbance field with a Mach 8 laminar boundary layer over a 7 deg half-angle blunt cone with a nose radius of 𝑅 𝑛 = 5.2 mm. The flow conditions and the axisymmetric cone geometry matched those measured in the Sandia Hypersonic Wind Tunnel at Mach 8 (Sandia HWT-8), and the incident freestream acoustic disturbances in the DNS were generated by acoustic radiation from the nozzle-wall turbulent boundary layer in the same tunnel. Consistent with the predictions of the nonmodal instability analysis, the study shows the emergence of a second spectral peak for moderately oblique waves between 150 kHz and 200 kHz in the aft part of the cone. The spectral energy of temperature and streamwise velocity fluctuations is initially concentrated within the entropy layer. These fluctiations are eventually “swallowed” by the boundary layer as the entropy-layer thickness 𝛿 𝑆 becomes similar to the boundary-layer thickness 𝛿h𝑡 at downstream locations. The numerical schlieren contours show the same inclined structures commonly observed in blunt cone experiments, and these structures are found to be three dimensional and advect with a constant speed approximately equal to the mean flow speed near the edge of the boundary layer.

Hypersonic Flow↗

NASA NTRSDate not supplied

Hypersonic Boundary-Layer Transition over a Blunt Circular Cone in a Mach 8 Digital Wind Tunnel

To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, three-dimensional direct numerical simulations (DNS) were conducted to investigate the interaction of a tunnel-like acoustic disturbance field with a Mach 8 laminar boundary layer over a 7 deg half-angle blunt cone with a nose radius of 𝑅 𝑛 = 5.2 mm. The flow conditions and the axisymmetric cone geometry matched those measured in the Sandia Hypersonic Wind Tunnel at Mach 8 (Sandia HWT-8), and the incident freestream acoustic disturbances in the DNS were generated by acoustic radiation from the nozzle-wall turbulent boundary layer in the same tunnel. Consistent with the predictions of the nonmodal instability analysis, the study shows the emergence of a second spectral peak for moderately oblique waves between 150 kHz and 200 kHz in the aft part of the cone. The spectral energy of temperature and streamwise velocity fluctuations is initially concentrated within the entropy layer. These fluctiations are eventually “swallowed” by the boundary layer as the entropy-layer thickness 𝛿 𝑆 becomes similar to the boundary-layer thickness 𝛿h𝑡 at downstream locations. The numerical schlieren contours show the same inclined structures commonly observed in blunt cone experiments, and these structures are found to be three dimensional and advect with a constant speed approximately equal to the mean flow speed near the edge of the boundary layer.

Hypersonic Flow↗

DOE OSTI2021

A computational study of turbulent separated flow over a wall-mounted cube at two different Reynolds numbers and incoming velocity profiles

Simulations of the canonical wall-mounted unit cube subjected to two distinct incident velocity profiles is performed at Reynolds numbers (Re) where the bulk flow characteristics are known to become relatively Re-insensitive using both direct numerical simulation (DNS) and wall-resolved large eddy simulation (WRLES). The aim of this work is to highlight the sensitivity of such bluff-body flows to mean shear and to provide a representative set of data for such flow scenarios where common turbulence modeling techniques often fail. Simple boundary conditions are selected to allow for easy comparisons for model development purposes and avoid confounding effects from freestream turbulence. In addition to mean velocity profiles, select turbulence statistics are presented in detail. We find that both mean velocity profiles and mean wake turbulence are Re-insensitive over the range examined here.

42 ENGINEERING↗

NASA NTRS1990

A computational parametric study of three-dimensional sidewall compression scramjet inlets at Mach 10

A computational parametric study of three-dimensional sidewall compression scramjet inlets has been performed. The parameters considered for the study include the leading edge sweep angle, varied between 30 and 60 degrees, and the cowl position, located at the throat and at two forward positions. Additionally, the effects of laminar and turbulent boundary layers as well as adiabatic and cold wall boundary conditions are assessed. The parametric study is performed for a Mach number of 10 and a unit freestream Reynolds number of 2 x 10 to the 6th/ft at a geometric contraction ratio of 5. Comparisons among the various configurations are made in terms of the gross parameters of mass capture, throat Mach number, total pressure recovery, and area weighted internal pressure ratios, as well as more detailed flow field phenomena comparisons. The inclusion of one 0-deg sweep computation indicates that the leading edge may be swept by up to 30 deg before significant changes in the gross flow field parameters occur. It is found that a 45-deg sweep configuration provides a good compromise of mass capture, total pressure recovery, and internal compression.

Holland, Scott D.↗

NASA NTRS1992

The semi-discrete Galerkin finite element modelling of compressible viscous flow past an airfoil

A method is developed to solve the two-dimensional, steady, compressible, turbulent boundary-layer equations and is coupled to an existing Euler solver for attached transonic airfoil analysis problems. The boundary-layer formulation utilizes the semi-discrete Galerkin (SDG) method to model the spatial variable normal to the surface with linear finite elements and the time-like variable with finite differences. A Dorodnitsyn transformed system of equations is used to bound the infinite spatial domain thereby permitting the use of a uniform finite element grid which provides high resolution near the wall and automatically follows boundary-layer growth. The second-order accurate Crank-Nicholson scheme is applied along with a linearization method to take advantage of the parabolic nature of the boundary-layer equations and generate a non-iterative marching routine. The SDG code can be applied to any smoothly-connected airfoil shape without modification and can be coupled to any inviscid flow solver. In this analysis, a direct viscous-inviscid interaction is accomplished between the Euler and boundary-layer codes, through the application of a transpiration velocity boundary condition. Results are presented for compressible turbulent flow past NACA 0012 and RAE 2822 airfoils at various freestream Mach numbers, Reynolds numbers, and angles of attack. All results show good agreement with experiment, and the coupled code proved to be a computationally-efficient and accurate airfoil analysis tool.

Meade, Andrew J., Jr.↗

NASA NTRS1993

Semi-discrete Galerkin solution of the compressible boundary-layer equations with viscous-inviscid interaction

A semi-discrete Galerkin (SDG) method is under development to model attached, turbulent, and compressible boundary layers for transonic airfoil analysis problems. For the boundary-layer formulation the method models the spatial variable normal to the surface with linear finite elements and the time-like variable with finite differences. A Dorodnitsyn transformed system of equations is used to bound the infinite spatial domain thereby providing high resolution near the wall and permitting the use of a uniform finite element grid which automatically follows boundary-layer growth. The second-order accurate Crank-Nicholson scheme is applied along with a linearization method to take advantage of the parabolic nature of the boundary-layer equations and generate a non-iterative marching routine. The SDG code can be applied to any smoothly-connected airfoil shape without modification and can be coupled to any inviscid flow solver. In this analysis, a direct viscous-inviscid interaction is accomplished between the Euler and boundary-layer codes through the application of a transpiration velocity boundary condition. Results are presented for compressible turbulent flow past RAE 2822 and NACA 0012 airfoils at various freestream Mach numbers, Reynolds numbers, and angles of attack.

Day, Brad A.↗

NASA NTRS2015

Measurement of Ultraviolet Radiative Heating Augmentation in HIEST Reflected Shock Tunnel

Radiance measurements in air at enthalpies from 8-20 MJkg have been made over a 250mm diameter flat-faced test article in Japan Aerospace Exploration Agency's HIgh-Enthalpy Shock Tunnel (HIEST). Measurements were made in the ultraviolet region (200-400 nm wavelength) in an attempt to resolve the long-standing discrepancy between theoryand measurements of heat flux over a blunt body; this discrepancy is often attributed toradiation. The spectra obtained indicate the presence of atomic iron vapor in the flowfield.At the highest enthalpies, the radiance is at the blackbody limit. An attempt to model theradiance is made by taking a nominal CFD flowfield without any contamination productsand processing it through a line-by-line radiation simulation tool. Iron vapor is introducedinto the shocked gas ahead of the model and radiation computations are repeated; the molefraction of iron vapor is adjusted to match the data. For the higher enthalpy conditions, theradiance was strongly absorbed and it was necessary to adjust the temperature and NOdensity in the freestream to match the signal below 300 nm. Once the observed spectrawere satisfactorily matched, the radiance to the stagnation point was then computed. It isshown that the impurity radiation is sufficiently large to explain the discrepancy.

Shock Tunnel↗

NASA NTRSDate not supplied

Turbulence Simulations of Transonic Flows over an NACA-0012 Airfoil

Three different simulation approaches, namely unsteady Reynolds-averaged Navier-Stokes (URANS), delayed detached-eddy simulation (DDES), and wall-modeled large-eddy simulation (WMLES) are employed to simulate transonic flow over an NACA-0012 airfoil at different angles of attack covering pre-and post-buffet-onset regimes. The freestream Mach number is 0.75,and the Reynolds number based on the chord length is 10million. These conditions are the same as the wind-tunnel experimental conditions of McDevitt and Okuno (1985). The NASA FUN3D solver is used for the simulations, which is an unstructured, compressible flow solver. The URANS simulations are performed using the Spalart-Allmaras (SA) model with the compressibility correction, the DDES predictions are based on the SA model, and the WMLES are performed using an equilibrium wall-model. The unsteady RANS simulations, only with the compressibility correction, predict the pre-and post-buffet characteristics, which compare well with the experimental results. DDES results predicted a lower buffet onset angle compared to experiment. The predicted shock locations are upstream of the locations predicted by URANS. Using a fine grid in the span wise direction, WMLES predictions show buffeting consistent with the experiment.

Transonic Buffet↗

NASA NTRS2023

Turbulence Simulations of Transonic Flows over an NACA-0012 Airfoil

Three different simulation approaches, namely unsteady Reynolds-averaged Navier-Stokes (URANS), delayed detached-eddy simulation (DDES),and wall-modeled large-eddy simulation (WMLES)are employed to simulate transonic flow over an NACA-0012 airfoil at different angles of attack covering pre- and post-buffet-onset regimes. The freestream Mach number is 0.75,and the Reynolds number based on the chord length is 10million. These conditions are the same as the wind-tunnel experimental conditions of McDevitt and Okuno (1985).1The NASA FUN3D solver is used for the simulations, which is an unstructured, compressible flow solver. The URANS simulations are performed using the Spalart-Allmaras (SA) model with the compressibility correction, the DDES predictions are based on the SA model, and the WMLES are performed using an equilibrium wall-model.The unsteady RANS simulations,only with the compressibility correction,predict the pre- and post-buffet characteristics,which compare well with the experimental results. DDES results predicted a lower buffet onset angle compared to experiment.The predicted shock locations are upstream of the locations predicted by URANS. Using a fine grid in the spanwise direction, WMLES predictions show buffeting consistent with the experiment

Transonic Buffet↗

NASA NTRS1990

Ultrasonic techniques for aircraft ice accretion measurement

Results of tests to measure ice growth in natural (flight) and artificial (icing wind tunnel) icing conditions are presented. Ice thickness is measured using an ultrasonic pulse-echo technique. Two icing regimes, wet and dry ice growth, are identified and the unique ultrasonic signal characteristics associated with these different types of ice growth are described. Ultrasonic measurements of ice growth on cylinders and airfoils exposed to artificial and natural icing conditions are presented. An accuracy of plus or minus 0.5 mm is achieved for ice thickness measurement using the pulse-echo technique. The performance of two-probe type ice detectors is compared to the surface mounted ultrasonic system. The ultrasonically measured ice accretion rates and ice surface condition (wet or dry) are used to compare the heat transfer characteristics for flight and icing wind tunnel environments. In general the heat transfer coefficient is inferred to be higher in the wind tunnel environment, not likely due to higher freestream turbulence levels. Finally, preliminary results of tests to measure ice growth on airfoil using an array of ultrasonic transducers are described. Ice profiles obtained during flight in natural icing conditions are shown and compared with mechanical and stereo image measurements.

Hansman, R. John, Jr.↗

DOE OSTI2024

Land-based wind plant wake characterization using dual-Doppler radar measurements at AWAKEN

Wind plant wakes have been shown to persist for tens of kilometers downstream in offshore environments, reducing the power output of neighboring plants, but their behavior on land remains relatively unexplored through observation. This study capitalizes on the unique and extensive field data collected for the American WAKE ExperimeNt (AWAKEN) project underway in northern Oklahoma. X-band dual-Doppler radars deployed at this site measure wind speed and direction at 25-m and 2-min resolution within a 30-km range, capturing the interactions between three neighboring wind plants. These measurements show that the wake of one wind plant extends at least 15 km downstream under easterly wind and stable atmospheric conditions. Though the wake wind speed increases within the first 10 km, it plateaus at 90% of the freestream wind speed. The spanwise velocity distribution within the wake initially shows the clear signature of the wind plant layout, which is smoothed as it propagates downstream, indicating spanwise momentum transfer is a key mechanism in wind plant wake development and recovery. These findings have important implications for wind plant siting decisions and resource assessments, and provide insights into atmospheric interactions at the wind plant scale.

17 WIND ENERGY↗