Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Temperature Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High-burnup Experiments in Reactivity Initiated Accidents (HERA)

HERA is a joint experimental program (JEEP) operating within the Nuclear Energy Agency’s (NEA’s) framework for irradiation experiments (FIDES). HERA is dedicated to the understanding of light water reactor (LWR) fuel performance at high burnup under reactivity-initiated accidents (RIA). During RIAs the fuel cladding can be breached by one of two mechanisms; pellet-cladding mechanical interaction or high temperature balloon and rupture. Pellet-cladding mechanical interaction (PCMI) failure occurs in the early phase of an RIA transient where the fuel pellet expands rapidly into the cladding prior to any meaningful heat transfer from the pellet to the cladding. This results in high stresses in the cladding resulting in crack propagation through the base Zircaloy metal and axially along the cladding tube. Failure by PCMI is a brittle failure mode and occurs at low cladding strains, approximately 2% hoop strain. If the cladding survives the PCMI phase of the transient, it may still fail due to ballooning and rupture induced by extended exposure to high temperature. Thermal transport from the fuel pin to the coolant is significantly reduced if a transition to film boiling on the cladding surface occurs. This result in both a rapid increase in fuel temperature, which drives fission gas release, and a spike in cladding temperature, which results in loss of mechanical strength. If the internal pressure of the fuel rod is greater than the system pressure the cladding can inelastically deform and eventually rupture. Failure by swelling and rupture occurs at larger strains, generally greater than 5% hoop strain. While PCMI failures are generally seen as more limiting, the dominance of one failure mode over the other can be affected by both the cladding material conditions, and the transient evolution.

(HERA)↗
DOE OSTI2023

Oxide Semiconductor Sensors for Monitoring Advanced Energy Conversion and Manufacturing Processes at High Temperature

To optimize the operation and functionality of high temperature systems such as slagging gasifiers, coal boilers and glass/steel smelters, it is important to monitor temperature, corrosion and erosion of the refractory used in such systems. Both thermocouple and failure sensors (and arrays of these) would be useful to monitor the health of any refractory or coatings in these systems. Many of such type of sensors are installed into the systems through open access ports within the refractory; however, there are some disadvantages of this approach where corrosive/erosive gas and molten materials can penetrate and compromise the system. The current work presents the development and performance of refractory with embedded high temperature sensors such as thermocouples, thermistors, and various spallation/crack monitoring sensors, which may be used within a variety of refractory brick in different high temperature processes and applications. The objective of our work is to develop high-temperature sensors composed of electroceramic materials that are chemically stable at high temperatures (750°-1500°C) and high pressures (up to 1000 psi) that can be used in monitoring temperature, corrosion and erosion process in refractory used in high energy systems. The high-temperature sensors investigated in this work were composed of various oxide composites directly embedded into the refractory oxides. The composites used for this work were synthesized by a mixed-oxide route. Metal oxides were inserted within a matrix material composed of refractory oxides (Al2O3, ZrO2, etc.). The physical and electrical properties were specifically manipulated by altering the level of percolation of the conductive species (metal oxides) within the refractory constituent (refractory oxide). An example of one of these embedded sensors consisted of an electroceramic-based thermocouple fabricated with two separate oxide composite compositions which were patterned to produce a couple within the interior of a refractory matrix. The thermocouple successfully displayed thermoelectric voltage trend (as a function of temperature), and the voltage was 220.0 mV near 1400 °C. In addition, corrosion tests on the refractory embedded sensors were performed. To evaluate corrosion in the refractory was exposed to high-temperature glass compositions over a 90 h period. The penetration of the glass through the refractory could be monitored by both an amperometric and voltametric based sensor. With this experiment, it was demonstrated that the embedded sensor could dynamically monitor the corrosion process, and thus, provide real-time feedback on both temperature and the refractory health.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Generation IV Benchmarking of TRISO Fuel Performance Models Under Accident Conditions Final Report

The Generation IV International Forum (GIF) is a co-operative international endeavor of fourteen members organized to carry out the research and development needed to establish the feasibility and performance capabilities of the next generation nuclear energy systems. GIF selected six reactor technologies, amongst which is the Very High Temperature Reactor (VHTR) that is primarily dedicated to the cogeneration of electricity and hydrogen. The technical basis for VHTR is the tristructural isotropic (TRISO)-coated particle fuel, the graphite as the core structure, helium coolant, as well as the dedicated core layout and lower power density to removal decay heat in a natural way. At the heart of safety features of the VHTR concept lie the TRISO fuel particles that are designed to keep their structural integrity and retain fission products at temperatures up to 1600°C. As part as the design and future operation of VHTRs, a key aspect is the accurate prediction of fuel performance under irradiation and accident conditions. Modeling and simulation allow prediction of TRISO fuel behavior when subject to neutron flux and in high temperature accident scenarios. The refinement of the fuel performance models and codes is performed by comparison to in-pile and out-of-pile experimental data that reproduce the expected irradiation conditions in high temperature gas-cooled reactors (HTGRs). Historically, the International Atomic Energy Agency (IAEA) developed a benchmark dedicated to the validation of predictive methods for fuel and fission product behavior through the Coordinated Research Program CRP-2 (IAEA, 1997). CRP-2 was later updated to cover fuel fabrication, quality assurance, irradiation performance, safety testing, and spent fuel. The scope of the resulting CRP-6 benchmarks focused on HTGR fuel performance and fission product release (IAEA, 2012). Taking advantage of additional TRISO fuel fabrication, irradiation, and safety testing campaigns, GIF launched a Generation IV Benchmarking of TRISO Fuel Performance Models under Accident Conditions in late 2015. This GIF benchmark is a three-year program steered by Idaho National Laboratory (INL, USA). The other participants include the Japan Atomic Energy Agency (JAEA, Japan) and the Korea Atomic Energy Research Institute (KAERI, Korea). The objectives of the benchmark are to: follow on the IAEA CRP benchmarks, (2) model fission product release under accident conditions, (3) compare results obtained by the fuel performance modeling codes of the benchmark participants, and (4) compare these code predictions to experimental data. Safety tests chosen for modeling include the first and second experiments of the Advanced Gas Reactor program (AGR-1 and AGR-2) and the High Flux Reactor (HFR) EU1bis experiment. This report presents the results obtained by the three research institutions using their respective fuel performance modeling codes. Comparisons of the corresponding fission product release predictions are made with experimental data from AGR-1, AGR-2, and HFR-EU1bis. The benchmark results show good agreements between all participants but also show a general trend of over-prediction of the experimental release data, which is mainly attributed to the use of over-estimated diffusion coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

AGR-2 Compact 6-4-1 Post-Irradiation Examination Results

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program was established to perform research and development on tristructural isotropic (TRISO)-coated particle fuel to support deployment of a high-temperature gas-cooled reactor (HTGR). The work continues as part of the Advanced Reactor Technologies (ART) TRISO Fuel Program. The overarching goal of the program is to provide a baseline fuel qualification data set to support licensing and operation of an HTGR. To achieve these goals, the program includes the elements of fuel fabrication, irradiation, post-irradiation examination (PIE) and safety/heating testing, fuel performance modeling, and fission product transport (INL 2017). Several fuel irradiation experiments have been performed at the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL), and additional irradiations are planned. These experiments are intended to provide data on fuel performance under irradiation, support fuel fabrication process development, qualify fuel for operating and accident conditions, provide irradiated fuel for accident testing, and support development of fuel performance and fission product transport models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Burn Intensity Drives the Alteration of Phenolic Lignin to (Poly) Aromatic Hydrocarbons as Revealed by Pyrolysis Gas Chromatography–Mass Spectrometry (Py-GC/MS)

High-intensity wildfires alter the chemical composition of organic matter, which is expected to be distinctly different from low-intensity prescribed fires. In this study, we used pyrolysis gas chromatography/mass spectrometry (Py-GC/MS), in conjunction with solid-state 13 C nuclear magnetic resonance (NMR) and Fourier transform infrared (FT-IR) spectroscopy, to assess chemical alterations from three wildfires and a long-term frequent prescribed fire site. Our results showed that black ash formed under moderate intensity burns contained less aromatic (ArH), polyaromatic hydrocarbon (PAH), and nitrogen-containing compounds (Ntg) but more lignin (LgC) and phenol compounds (PhC), compared to white ash formed under high intensity burns. Both 13 C NMR and FT-IR confirmed a higher relative percentage of carboxyl carbon in white ash, indicating the potential for higher water solubility and more mobile carbon, relative to black ash. Compared to wildfires, ash from low-intensity prescribed fire contained less ArH, PAH, and Ntg and more LgC and PhC. Controlled laboratory burning trials indicated that organic matter alteration was sensitive to the burn temperature, but not related to the fuel type (pine vs fir) nor oxygen absence/presence at high burn temperatures. This study concludes that higher burn temperatures resulted in higher (poly)aromatic carbon/nitrogen and lower lignin/phenol compounds.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Progress on Producing an ODS Ferritic Alloy by High Deformation Processing of Reactive Powders

Oxide dispersion-strengthened (ODS) ferritic alloys, such as 14YWT, are considered as benchmarks for fuel cladding and core structural materials in advanced nuclear energy reactor systems that require high temperature strength and creep properties as well as resistance to radiation damage. Unfortunately, the popular processing method of mechanical alloying (MA) is time-consuming, incurs high manufacturing costs, and typically produces anisotropy in the microstructure and mechanical properties of ODS ferritic alloys. These considerations hinder their acceptance in many high-performance, high-temperature materials for advanced nuclear energy reactors. This work package is pursuing an alternative solid-state processing to MA involving high deformation at high temperatures for producing an ODS ferritic alloy for fuel cladding. This report summarizes the concept for this processing method and the progress toward selecting the reactive and ferritic alloy powders, preparing 316L stainless steel cans for filling with blended powder followed by degassing, and choosing the heat treatments and forging parameters for performing the first two forging experiments. The preliminary results of optical microscopy performed on polished samples that were cut in three orthogonal directions revealed remnant porosity in both samples. The analysis of the porosity using ImageJ revealed a lesser amount of ~2.49% in the HiLoMe-1 sample that was processed with the three heat treatments and forging parameters compared to ~5.70% for the Hi-1 sample that was processed with only the first sintering heat treatment and forging parameter. These initial results will provide insights that can be leveraged to improve the densification of the powders in future forging experiments that will be continued into FY24 for determining the optimum heat treatments and forging parameters coupled with detailed microstructure characterization studies for producing the ODS ferritic alloy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Experimental results of conductive inserts to reduce nuclear fuel temperature during nuclear volumetric heating

Advanced fuel designs that incorporate thinner fuel UO2 pellets interspaced by high thermal conductivity inserts have been proposed, with the primary goals of reducing peak centerline temperatures and temperature gradients across fuel pellets and enhancing heat transfer from the fuel to the coolant. An initial series of experiments has been performed on this design, including laboratory experiments and a series of experiments using the Idaho National Laboratory (INL) Transient Reactor Test (TREAT) Facility, the latter of which compared thermal gradient driven fracture of standard pellet designs with that in the proposed advanced fuel design. Although reducing fracture is not the primary objective of the new fuel design, the lower thermal gradients are expected to reduce fracture, so it can serve as an indicator of the thermal behavior of this fuel in the reactor. The in-reactor tests were conducted at multiple linear heat generation rates and confirm the expected result that fracture in both the standard and advanced fuel pellets occurs during the first ramp to power in standard light-water reactor conditions. Post-irradiation examination of the experiment material was performed and included quantification of the extent of fracture in the fuel pellets. It was found that the advanced-design pellets reduce the extent of fracture in a statistically significant way. This confirms the expected behavior predicted by two-dimensional axisymmetric models of this experiment. Here in this study is an important first experimental confirmation of the efficacy of the proposed inserts for achieving their desired effect on the thermal behavior of the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Development of a TRISO assessment case for BISON based on transient experiments in the NSRR

The tristructural isotropic (TRISO) fuel assessment and validation database currently available in BISON is based mainly on steady-state irradiation and high-temperature furnace testing. Transient assessment cases are needed to support ongoing U.S. industry efforts to design and deploy commercial reactors that utilize TRISO fuels. Most available historical transient tests involving TRISO fuels were characterized by power densities, temperatures, and energy depositions that were highly conservative with respect to typical high-temperature gas-cooled reactor (HTGR) accident conditions. Nonetheless, assessment of BISON's predictive capabilities, adaptation of material properties toward high-temperature and high-particle-power regimes, and development of a systematic approach to validating BISON for TRISO transient applications now motivate the modeling of historical transient tests. This work describes the development of 1-D thermal models of transient experiments conducted at the Nuclear Safety Research Reactor (NSRR) in Japan, with BISON predictions of energy deposition, UO2 melting onset, and molten volume fractions being compared against experimental measurements. Melting is accounted for by defining an effective specific heat capacity for UO2—one that leverages the material's heat of melting. BISON's predictions of energy deposition and molten volume fraction are in good agreement with the experimental data from the low-energy-deposition tests; however, BISON tends to overpredict melting at higher energy depositions. Though overly conservative compared to the operating conditions expected for near-term TRISO-fueled reactor applications, these simulations effectively exercise BISON TRISO models over a wider range of conditions than those encompassed by the existing assessment database. Potential contributors to the observed discrepancies are noted and additional future developments proposed.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Techno-economic Analysis for a Low Cost and Recyclable Oxygen Carrier

The novelty of a chemical looping combustion (CLC) process is its ability to oxidize solid or gaseous fuels in a nitrogen-free environment eliminating the need for post combustion carbon dioxide capture. The technology is based on the oxygen carrier (OC); a metal oxide that at high temperatures can undergo a reduction reaction with a fuel, followed by an oxidation reaction with air. Successful development of CLC processes is dependent on the OC having: low cost, high attrition resistance under CLC conditions, and high reactivity for coal. In this paper, we discuss the development of a novel iron-based OC formulation produced from low cost and abundant raw materials. The active OC components are recyclable, with reformulated material performance comparable to the virgin OC, even when reformulated with ash contents of up to 10%. Furthermore, we discuss a techno-economic analysis for a centrally located OC facility for the novel OC, with a production capacity of 1 million metric tonnes per year. The facility serves a hypothetical market comprising 25 chemical looping combustion facilities, averaging 5 tonnes per hour OC replacement per facility. Estimates for the cost of the OC are around $150/tonne, and include an energy-to-power option to improve process economics.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Atomistic and cluster dynamics modeling of fission gas (Xe) diffusivity in TRISO fuel kernels

TRISO fuel particles are candidates for use in next generation reactors including gas reactors, fluoride salt-cooled high temperature reactors, and micro-reactors. The UCO fuel kernel consists of a uranium dioxide (UO) and uranium carbide mixture. The addition of UC helps suppress the formation of carbon monoxide gas, which led to failures during initial TRISO development. The addition of uranium carbide alters the chemistry of the UO kernel, which is known to influence performance parameters such as fission gas diffusivity, although the impact has not been quantified and no models exist that take the change in chemistry into account. Therefore, better understanding and more accurate models of the impact of chemistry on fuel performance are of high priority. In this paper, a first-principles density functional theory (DFT) and empirical potential based multi-scale study has been carried out to model the diffusivity of fission gas xenon (Xe) in UCO TRISO fuel kernels. The focus is on the UO component in the UCO fuel kernels, as that represents the largest volume fraction of the fuel kernels. The study relies on DFT and empirical potential calculations to determine Xe and point defect properties, which are then used in thermodynamic and kinetic models to predict diffusion for intrinsic conditions. In addition, the information is utilized in cluster dynamics simulations using the Centipede code to estimate the impact of irradiation on defect transport. Additionally, the presence of UC or UC in the UCO fuel kernels is shown to have a substantial impact on the UO non-stoichiometry by inducing oxygen vacancies and driving UO sub-stoichiometric, which causes much slower Xe diffusion in UCO compared to light water reactor UO fuel. The application of this model in fuel performance simulations using the Bison code is also demonstrated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Comparing Cetane Number Measurement Methods

Cetane number is one of the most important fuel performance metrics for mixing controlled compression-ignition “diesel” engines, quantifying a fuel’s propensity for autoignition when injected into end-of-compression-type temperature and pressure conditions. The historical default and referee method on a Cooperative Fuel Research (CFR) engine configured with indirect fuel injection and variable compression ratio is cetane number (CN) rating. A subject fuel is evaluated against primary reference fuel blends, with heptamethylnonane defining a low-reactivity endpoint of CN = 15 and hexadecane defining a high-reactivity endpoint of CN = 100. While the CN scale covers the range from zero (0) to 100, typical testing is in the range of 30 to 65 CN. Alternatively, several constant-volume combustion chamber (CVCC)-based cetane rating devices have been developed to rate fuels with an equivalent derived cetane number (DCN) or indicated cetane number (ICN). These devices measure ignition delay for fuel injected into a fixed volume of high-temperature and high-pressure air to simulate end-of-compression-type conditions. In this study, a range of novel fuel compounds are evaluated across three CVCC methods: the Ignition Quality Tester (IQT), Fuel Ignition Tester (FIT), and Advanced Fuel Ignition Delay Analyzer (AFIDA). Resulting DCNs and ICNs are compared for fuels within the normal diesel fuel range of reactivity, as well as very high (~100) and very low DCNs/ICNs (~5). Distinct differences between results from various devices are discussed. This is important to consider because some new, high-efficiency advanced compression-ignition (CI) engine combustion strategies operate with more kinetically controlled distributed combustion as opposed to mixing controlled diffusion flames. These advanced combustion strategies may benefit from new fuel chemistries, but current rating methods of CN, DCN, and ICN may not fully describe their performance. In addition, recent evidence suggests ignition delay in modern on-road diesel engines with high-pressure common rail fuel injection systems may no longer directly correlate to traditional CN fuel ratings. Simulated end-of-compression conditions are compared for CN, DCN, and ICN and discussed in the context of modern diesel engines to provide additional insight. Results highlight the potential need for revised and/or multiple fuel test conditions to measure fuel performance for advanced CI strategies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

NDMAS

Overview of Current ART-GCR Data: Fuel Fabrication, Irradiation Monitoring (Fuel & Graphite – near real-time for HDG-1), Post-Irradiation Examination (Fuel & Graphite), Graphite Characterization (Baseline and Irradiated), High Temperature Metals Mechanical Tests, Design, Methods, and Validation Data, Japan Atomic Energy Agency’s High Temperature Test Reactor (HTTR), Argonne National Laboratory’s Natural convection Shutdown heat removal Test Facility (NSTF), Oregon State University’s High Temperature Test Facility (HTTF), Generation IV International VHTR Materials Handbook, Additional related data, and Advanced Test Reactor operations (near real-time).

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Flash Diffusivity Measurement of Semi-Porous Insulation Material Intended for Radioisotope Thermoelectric Generators

This research involves the analysis of flash-heating data pursuant to find the thermal diffusivity of a semi-porous insulation material (Min-K) that is being considered for use in a radioisotope thermoelectric generator (RTG). An RTG uses radioactive nuclear fuel to produce electricity through a temperature difference imposed on a bimetallic thermocouple. Insulation is required to protect sensitive equipment from high temperatures and to conserve heat in the fuel. Using flash diffusivity temperature data, various simulations were fitted in order to find the most appropriate heat transfer model for the experiments. Four models were allowed to compete and the standard deviation of the residuals were compared for each model in evaluating model performance. The residuals are simply the difference in temperatures between the measurements and the mathematical models at each measurement point.

McMasters, Robert L.↗
DOE OSTI2021

Fuel properties effects on wall-wetting and fuel-in-lube dilution under stochastic pre ignition prone conditions

Fuel-engine interactions have been shown to influence stochastic pre-ignition (SPI), however there is uncertainty on the root causes, participially if effects are primarily physical or chemical in nature. To better delineate the physical and chemical dependencies of fuel properties on SPI, this work studies interactions between aromatics, distillation, and particle matter index on SPI with a laser induced fluorescence (LIF) diagnostic to observe wall wetting. Fuels with high aromatic components or higher distillation temperatures tend to increase SPI events, but it is not well understood if the increased fuel dilution or a chemical aspect of this process is the primary mechanism for SPI. By employing the novel LIF in this work we measure fuel dilution in real-time in a running single cylinder research engine operated at SPI conditions. Three fuels were used in the present work, with the LIF diagnostic. Each fuel was operated at two injection timings, generating fuel specific effects on wall wetting. The LIF measurements are coupled with engine combustion measurements and SPI event counts. Results enable a deconvolution of fuel physical and chemical properties on SPI propensity, providing unique and novel insights into the dominant fuel effects affecting SPI.

Splitter, Derek↗
DOE OSTI2021

AGR-2 TRISO Fuel Post-Irradiation Examination Final Report

An array of post-irradiation exams and experiments were employed to assess the irradiation performance and high-temperature behavior of AGR-2 UCO TRISO fuel produced in an engineering-scale coater. Work was also conducted on UO2 TRISO fuel produced for comparison with the AGR UCO fuel. Emphases we replaced on enumerating the frequency of SiC layer failures (failure of the SiC layer with at least one PyC layer remaining intact) and TRISO failures (failure of all three dense layers) and evaluating the retention of key fission products within the fuel. Examinations of the fuel kernel and coating morphologies were used to understand the features typical of normal intact fuel, degraded or failed fuel, and mechanisms of degradation. Radiochemical analyses were used to determine their retention within the fuel. The results confirm excellent performance of the fuel that exceeds historical HTGR design requirements with significant margin.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Examination of Legacy Metallic Fuel Pins (U-10Zr) Tested in FFTF

The MFF series of metallic fuel (U-10wt%Zr) tests performed in the Fast Fuel Test Facility (FFTF) were the beginning tests to qualify the fuel as a driver fuel for FFTF. They all performed very well, to relatively high burnup and with no pin breaches. Tests MFF-3 and MFF-5 were chosen to be destructively examined because they were run at high peak cladding temperatures, 643 and 649°C respectively, and to modest to high burnup (138 and 101 MWd/kgM respectively). They were the only sodium fast reactor (SFR) metallic tests, with long (91.4 cm) fuel columns and clad in HT9, to be operated at these high temperatures. Extensive operating condition reconstruction was performed to accompany the examination, providing detailed operating conditions axially along the pins. In addition, detailed ORIGEN calculations provided fuel burnup along the pin length. These calculations and detailed cross-section metallography allowed a PhD dissertation to be performed where the fuel/cladding chemical interaction (FCCI) was modeled using Fickian and Soret Effect driven diffusion of rare earth fission products to the cladding surface and interact with the cladding. The examination of the MFF-3 and MFF-5 pins included neutron radiography, axial profilometry including pin bow and length measurements, precision gamma scanning, plenum gas puncturing to measure fission gas release, detailed chemical/isotopic analyses of fuel samples to confirm burnup calculations, and metallography of pin cross-sections, including micro-hardness measurements of fuel and cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Determination of oxidation rates and volatile oxidation products for HTGR graphite matrix material exposed to steam atmospheres

High-temperature gas-cooled reactors (HTGRs) in operation use tristructural isotropic (TRISO) particles embedded in graphite and carbonized resin matrix to form the fuel element. This graphite matrix material serves as a supportive structural element, heat transfer medium, and neutron moderator. In HTGR designs, fuel compacts are exposed to helium coolant, which facilitates high outlet temperatures (750°C 2 O, 800°C 2 , and H 2 , are quantified in varied oxidant atmospheres using a coupled thermogravimetric analyzer and mass spectrometer. Furthermore, oxidation rates reported here for varied steam (H 2 O [g]) atmospheres are predominantly linear and comparable with literature values in the range of tested temperatures (800–1200°C). Changes in dominant matrix oxidation products from primarily CO to a mixture of CO, CO 2 , and H 2 were observed at higher temperatures (≥1000°C) and steam atmospheres (≥5 kPa pH 2 O). Kinetic data indicates that there was no shift in oxidation regime with chemical oxidation occurring at all temperatures and H2O (g) atmospheres tested. These data provide insight into the oxidation behavior of graphite matrix material and will inform future testing conditions, notably mixed atmospheric conditions, of HTGR fuel elements.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural evolution of Mo-UO 2 cermets under high temperature hydrogen environments

Ceramic-metallic (cermet) materials show promise for use in nuclear thermal propulsion applications due to attractive thermophysical properties including high temperature stability and high thermal conductivity. In this work, molybdenum-uranium dioxide (Mo-UO 2 ) cermet fuel elements were fabricated by means of spark plasma sintering (SPS) and were subsequently exposed to hydrogen at high temperatures (2500 K). Mo-UO 2 samples pre- and post-exposure were characterized by means of optical microscopy, scanning electron microscopy, and X-ray diffraction (XRD). Microscopy analyses of the as-produced material displayed microscopic cracking on the interior of the spherical UO 2 fuel particles but confirmed that the fuel particles were fully encapsulated in the Mo matrix. The results further showed mass loss, macroscopic swelling, and cracking in the cermet samples which occurred during high temperature hydrogen testing. Nanoscale swelling was evidenced by XRD in the Mo matrix and UO 2 fuel structure due to the incorporation of defects and accompanied microstrain.

36 MATERIALS SCIENCE↗