Search NASA⌕ Search

SEARCH · Search NASA

Results for “IMPACT TESTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Effect of fiber diameter and matrix alloys on impact-resistant boron/aluminum composites

Efforts to improve the impact resistance of B/Al are reviewed and analyzed. Nonstandard thin-sheet charpy and Izod impact tests and standard full-size Charpy impact tests were conducted on composites containing unidirectional 0.10mm, 0.14mm, and 0.20mm diameter boron fibers in 1100, 2024, 5052, and 6061 Al matrices. Impact failure modes of B/Al are proposed in an attempt to describe the mechanisms involved and to provide insight for maximizing impact resistance. The impact strength of B/Al was significantly increased by proper selection of materials and processing. The use of a ductile matrix and large diameter boron fibers gave the highest impact strengths. This combination resulted in improved energy absorption through matrix shear deformation and multiple fiber breakage.

Mcdanels, D. L.↗
NASA NTRS1995

Neural Networks Analyze Data In Particle-Impact-Noise Tests

Electronic neural networks and computers put to use in analyzing data acquired in particle-impact-noise-detection (PIND) tests of packaged electronic components. PIND tests detect loose particles in packages that cause failures during subsequent operation of packages in presence of accelerations or other effects - for example, loose electrically conductive particles that bounce into positions in which they cause short circuits. Interpretation of test data more objective and accurate. Preliminary results suggest use of neural networks result in significant improvement in quality and reliability and decrease in cost of PIND testing.

Scaglione, Lois J.↗
NASA NTRS2019

Analysis of the DebriSat Fragments and Comparison to the NASA Standard Satellite Breakup Model

Existing DOD and NASA satellite breakup models are based on a key laboratory test, the 1992 Satellite Orbital debris Characterization Impact Test, which has supported many applications and matched on-orbit events involving older satellite designs reasonably well over the years. In 2014, the NASA Orbital Debris Program Office, in collaboration with the Air Force Space and Missile Systems Center, The Aerospace Corporation, and the University of Florida, conducted a hypervelocity impact test using a high-fidelity, mock-up satellite, DebriSat, in controlled and instrumented laboratory conditions to update and improve these models. DebriSat is representative of present-day, low Earth orbit satellites, having been constructed with modern spacecraft materials and techniques. The DebriSat fragment ensemble provided a variety of shapes, bulk densities, and dimensions. Fragments down to 2 mm in size are being characterized by their physical and derived properties. The data will inform updates to the current NASA Standard Satellite Breakup Model (SSBM), which was formulated using laboratory and ground-based measurements of on-orbit fragmentation events to describe an average breakup for spacecraft and upper-stage collisions and explosions. Although individual fragment collection and characterization is still ongoing, this paper will present the status of the DebriSat fragment data analysis including cumulative characteristic length and cumulative mass distributions, area-to-mass distributions, and characteristic length versus mass distributions. Additionally, comparisons to the NASA SSBM will be presented.

Murray, James↗
NASA NTRS2008

Groundwater Remediation and Alternate Energy at White Sands Test Facility

White Sands Test Facility Core Capabilities: a) Remote Hazardous Testing of Reactive, Explosive, and Toxic Materials and Fluids; b) Hypergolic Fluids Materials and Systems Testing; c) Oxygen Materials and System Testing; d) Hypervelocity Impact Testing; e)Flight Hardware Processing; and e) Propulsion Testing. There is no impact to any drinking water well. Includes public wells and the NASA supply well. There is no public exposure. Groundwater is several hundred feet below ground. No air or surface water exposure. Plume is moving very slowly to the west. Plume Front Treatment system will stop this westward movement. NASA performs on-going monitoring. More than 200 wells and zones are routinely sampled. Approx. 850 samples are obtained monthly and analyzed for over 300 different hazardous chemicals.

Fischer, Holger↗
NASA NTRS2001

Development and Evaluation of Stitched Sandwich Panels

This study explored the feasibility and potential benefits provided by the addition of through-the-thickness reinforcement to sandwich structures. Through-the-thickness stitching is proposed to increase the interlaminar strength and damage tolerance of composite sandwich structures. A low-cost, out-of-autoclave processing method was developed to produce composite sandwich panels with carbon fiber face sheets, a closed-cell foam core, and through-the-thickness Kevlar stitching. The sandwich panels were stitched in a dry preform state, vacuum bagged, and infiltrated using Vacuum Assisted Resin Transfer Molding (VARTM) processing. For comparison purposes, unstitched sandwich panels were produced using the same materials and manufacturing methodology. Test panels were produced initially at the University of Utah and later at NASA Langley Research Center. Four types of mechanical tests were performed: flexural testing, flatwise tensile testing, core shear testing, and edgewise compression testing. Drop-weight impact testing followed by specimen sectioning was performed to characterize the damage resistance of stitched sandwich panels. Compression after impact (CAI) testing was performed to evaluate the damage tolerance of the sandwich panels. Results show significant increases in the flexural stiffness and strength, out-of-plane tensile strength, core shear strength, edgewise compression strength, and compression-after-impact strength of stitched sandwich structures.

Stanley, Larry E.↗
NASA NTRS2023

Orbital Debris Shape Effect Investigations for Mitigating Risk

NASA’s Orbital Debris Program Office (ODPO) and Hypervelocity Impact Technology (HVIT) team have coordinated to better understand the risks to upper stages and spacecraft from non-spherical orbital debris. It is well understood that fragmentation (collision or explosion) events in orbit produce fragments of various materials, sizes, and shapes. To further characterize these parameters, the ODPO is developing the next-generation Orbital Debris Engineering Model (ORDEM) version 4.0 to include orbital debris shape distributions. Ground-based assets, such as radar and optical sensors, can provide size estimates and some insight into material based on radar return or optical filter photometry/spectroscopy, respectively. Characterizing an object’s shape requires more laboratory analyses to infer how shape affects these measurements. More importantly, in addition to size and material/density, the shape of fragments in orbit will alter the ballistic limit equations used in orbital debris risk assessments with NASA’s Bumper Code. The ODPO plans to release ORDEM 4.0 in the coming years. Performing ground-based laboratory impact tests on high-fidelity spacecraft mockups provides the means to directly measure size, mass, material/density, and shape of fragments, all key parameters needed to characterize real-world break up events. The DebriSat test, the results of which are provided, showcases the details of this type of experiment. The goal of this collaborative research between the ODPO and the HVIT team is to include a shape parameter in the environmental and breakup models used to assess risk for various space structures. This paper examines ground-based laboratory impact tests and the associated fragment shape categories. Provided these defined shapes, the approach is simplified by assuming a right circular cylinder (RCC) approximation with varying length-to-diameter ratios. Highlights of impact tests conducted by the HVIT team using non-spherical projectiles based on the RCC approximation are presented. Hydrocode simulations have also been performed to expand on the complexity of variations with non-spherical projectiles. Lastly, ray-tracing simulations of various RCCs of known material are provided to support the ongoing research on optical reflectance distributions with known shapes and to highlight how this may modify the current optical size estimation model. The status and plan forward are outlined for NASA's orbital debris shape effect investigation using a multidisciplinary approach by the ODPO and the HVIT team.

Heather Cowardin↗
NASA NTRS2023

Orbital Debris Shape Effect Investigations for Mitigating Risk

NASA’s Orbital Debris Program Office (ODPO) and Hypervelocity Impact Technology (HVIT) team have coordinated to better understand the risks to upper stages and spacecraft from non-spherical orbital debris. It is well understood that fragmentation (collision or explosion) events in orbit produce fragments of various materials, sizes, and shapes. To further characterize these parameters, the ODPO is developing the next-generation Orbital Debris Engineering Model (ORDEM) version 4.0 to include orbital debris shape distributions. Ground-based assets, such as radar and optical sensors, can provide size estimates and some insight into material based on radar return or optical filter photometry/spectroscopy, respectively. Characterizing an object’s shape requires more laboratory analyses to infer how shape affects these measurements. More importantly, in addition to size and material/density, the shape of fragments in orbit will alter the ballistic limit equations used in orbital debris risk assessments with NASA’s Bumper Code. The ODPO plans to release ORDEM 4.0 in the coming years. Performing ground-based laboratory impact tests on high-fidelity spacecraft mockups provides the means to directly measure size, mass, material/density, and shape of fragments, all key parameters needed to characterize real-world break up events. The DebriSat test, the results of which are provided, showcases the details of this type of experiment. The goal of this collaborative research between the ODPO and the HVIT team is to include a shape parameter in the environmental and breakup models used to assess risk for various space structures. This paper examines ground-based laboratory impact tests and the associated fragment shape categories. Provided these defined shapes, the approach is simplified by assuming a right circular cylinder (RCC) approximation with varying length-to-diameter ratios. Highlights of impact tests conducted by the HVIT team using non-spherical projectiles based on the RCC approximation are presented. Hydrocode simulations have also been performed to expand on the complexity of variations with non-spherical projectiles. Lastly, ray-tracing simulations of various RCCs of known material are provided to support the ongoing research on optical reflectance distributions with known shapes and to highlight how this may modify the current optical size estimation model. The status and plan forward are outlined for NASA's orbital debris shape effect investigation using a multidisciplinary approach by the ODPO and the HVIT team.

Heather Cowardin↗
NASA NTRSDate not supplied

A Historical Overview of the NASA Orbital Debris Program Office’s Laboratory Optical Measurements

The NASA Orbital Debris Program Office (ODPO) has used laboratory measurements to help bring ground-based measurements together with models to ascertain Earth-orbiting target parameters of interest to support various orbital debris models. In 2005, the Optical Measurement Center (OMC) was established to simulate space-based illumination conditions using equipment and techniques that recreate telescopic observations, particularly source-target-sensor orientations. The intent was to recreate light curves using known aspect angles of known targets and phase angles (angle is defined by the vertex between illumination source-object-detector) to complement telescopic observations that could be used to update the current optical size estimation model (OSEM) – a model that converts object brightness into size for orbital debris models. To support the above goals, the laboratory has undergone several equipment upgrades to increase capabilities over almost 20 years of operation. The primary instrumentation acquires reflectance measurements and includes a solar-like light source, CCD camera with astrometric filters, and robotic arm. A rotary arm was added approximately five years after full operation to allow acquisition through a full 360° range of phase angles. Another part of the OMC instrumentation is a field spectrometer, predominately used for field operations to acquire pre- and post-flight spacecraft material spectral measurements. Additionally, reflectance spectroscopy of various materials is also of interest resulting from hypervelocity impact tests, pristine spacecraft materials, or samples of materials that are used in spacecraft design. These measurements are stored in NASA’s Spectral Material Database, a resource that is still being populated today. The study of spectral measurements also enabled the development of spectral unmixing routines to support the identification of spacecraft materials from spectral data gathered by ground based telescopes. Preliminary OMC investigations focused on feasibility studies to acquire 360° rotation light curves of simple shapes at a single-phase angle and extended to measurements of representative fragments from ground-based explosion tests. To correlate the light curves with ground-based optical measurements, a focused study on high area to mass materials was conducted in support of a newly identified population (at the time) in geosynchronous orbit (GEO) consisting of multi-layered insulation. To further characterize orbital debris, a larger selection of materials was analyzed using laboratory photometric measurements that included representative targets from pristine spacecraft materials and ground-based impact tests. Around 2012, an initiative was requested to understand the feasibility of active debris removal (ADR) of larger targets using grappling methods for spent rocket bodies. Using a priori information on selected targets, scaled-down versions of rocket bodies were generated thanks to improvements in 3D printing technology and machining. These targets were studied in the OMC to understand rotation characteristics. These were compared with telescopic data to determine if the tumble and rotation angles would allow ADR. In 2013, the OMC focused on combining spectral measurements with photometric data to characterize GEO orbital debris. Several years later, NASA acquired a Titan III Transtage test article from “The Boneyard” with a high-resemblance to on-orbit Titan III Transtage rocket bodies, allowing physical access to a representative rocket body that suffered fragmentations in GEO. This prompted the creation of 3D models using lidar technology and spectral measurements of the materials. Focused research also transitioned to specific materials (i.e., solar cells) when telescopic surveys requested characterization of specific GEO targets. In the different research products presented, the focus has been to understand the various parameters that influence optical size estimation, including albedo, phase functions, and brightness variations. Work in this area continues with newer sources of data, including DebriSat, a high-fidelity 56-kg spacecraft replica representative of a modern low Earth orbit (LEO) satellite subjected to a laboratory hypervelocity impact test to understand fragmentation events and to support updates to satellite breakup models and size estimation models. Utilizing the vast population of fragments from DebriSat and prior laboratory impact experiments, the ODPO has focused on acquiring bidirectional reflectance distribution function (BRDF) data to characterize targets in the laboratory, thus removing aspect angle dependencies. Additionally, the DebriSat project has provided improved processes for measuring size via image acquisition, such that a true fragment size can be directly compared to the derived size using the OSEM. The team continues to assess BRDFs and use spectral measurement data to investigate the parameters used in the OSEM, specifically magnitudes, albedo, and phase functions.

Heather Cowardin↗
DOE OSTI2011

SMALL-SCALE SAFETY TEST REPORT FOR RDX (SECOND CALIBRATION)

RDX was provided by Indian Head and was dried at 60 C for 16 hours, cooled and kept in a desiccator before use. Please note that the impact testing was done on both pellets and loose powder which resulted in different data. The impact sensitivity on pressed pellets was 34 cm that is greater than that on loose powder, as expected. The impact test data on the loose powder was similar to what Indian Head and LANL got. Remarkable consistent results were observed for test results of loose powder RDX. The average impact sensitivyt (DH{sub 50}) was 21.8 cm and the average friction sensitivity (F{sub 50}) for loose powder was 24.9 kg, respectively. DSC charts showed that peak temperatures and onset temperatures for all 3 runs of RDX samples were almost identical. All electrostatic spark sensitivity was 0/10 at 1.0 J with a 510-ohm resistor in the discharge circuit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1995

Duplication and analysis of meteoroid damage on LDEF and advanced spacecraft materials

The analysis of exposed surfaces on LDEF since its retrieval in 1990 has revealed a wide range of meteoroid and debris (M&D) impact features in the sub-micron to millimeter size range, ranging from quasi-infinite target cratering in LDEF metallic structural members (e.g. inter-costals, tray clamps, etc.) to non-marginal perforations in metallic experimental surfaces (e.g. thin foil detectors, etc.). Approximately 34,000 impact features are estimated to exist on the exposed surfaces of LDEF. The vast majority of impact craters in metal substrates exhibit circular footprints, with approximately 50 percent retaining impactor residues in varying states of shock processing. The fundamental goals of this project were to duplicate and analyze meteoroid impact damage on spacecraft metallic materials with a view to quantifying the residue retention and oblique impact morphology characteristics. Using the hypervelocity impact test facility established at Auburn University a series of impact tests (normal and oblique incidence) were executed producing consistently high (11-12 km/s) peak impact velocities, the results of which were subsequently analyzed using Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDXS) facilities at Auburn University.

Hill, David C.↗
DOE OSTI2018

Evolution of microstructures and mechanical properties during solution treatment of a Ti–V–Mo-containing high‑manganese cryogenic steel

Highlights: • High-Mn cryogenic steels are getting the spotlight in the cryogenic market. • The grain size grew slowly and the yield strength remained almost stabilized with an increase of solutionizing temperature. • The Hall–Petch strengthening coefficient for yield strength was small, estimated to be 153 MPa μm{sup 0.5}. • The weakening effect of solutionizing temperature on grain size was attributed to the nano-sized (Ti, V, Mo)C precipitate. - Abstract: The effect of solution treatment on the microstructure and mechanical properties of a high‑manganese (Mn) twin-induced plastic (TWIP) cryogenic steel that was alloyed from elemental titanium (Ti), vanadium (V) and molybdenum (Mo) was investigated by a variety of techniques such as microstructural characterization, room tensile testing and − 196 °C impact testing. The austenite grain size grew slowly with an increase of the solutionizing temperature (ST). The relatively weak effect of the ST on the austenite grain size is attributed to the superior thermal stability and coarsening resistance of the (Ti, V, Mo)C precipitate, which hindered austenite grain growth. An increase in ST improved the low-temperature toughness (LTT) significantly and decreased the strain hardening rate (SHR), but had no significant effect on the yield strength. The Hall–Petch strengthening coefficient for yield strength was small, and was estimated to be 153 MPa μm{sup 0.5}. Undissolved large-sized chromium (Cr) carbide can deteriorate the LTT significantly. Because of its excellent mechanical properties, high-Mn steel that was alloyed by elemental Ti, V and Mo can be used to manufacture storage tanks for liquefied natural gas.

36 MATERIALS SCIENCE↗
NASA NTRS2023

Modeling of Response of Thermoplastic Composites Under High Energy Impact

This work investigates the response of a thermoplastic panel under high energy ballistic impact. The composite material system is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK3). Several high energy dynamic impact tests were performed where an aluminum projectile impacted various panels at different impact velocities. For this work, the test performed at an impact velocity of 73.2 m/s was investigated. The projectile rebounded upon impact, and the damage to the panel was characterized through ultrasonic and CT-scanning. Response of the panel under impact and the associated damage is discussed. Numerical simulation of the impact process was performed using the LS-DYNA® computer code [1] with a new material model MAT_COMPOSITE_DAMAGE_DGD (MAT 299), a modification over MAT 261 material model in terms of an improved representation of damage coupling and additional capability for strain rate effects. Delaminations were modeled using cohesive zone contact formulation in LS-DYNA®, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. Simulation of this impact test demonstrates a good match of results in terms of panel deflection and panel-projectile interactions. The overall extent of delaminations was under-predicted by the simulation. This work forms the basis to model tests performed at higher velocities, involving projectile penetration of panel.

Composite Materials↗
NASA NTRS2013

Aerogel-Based Multilayer Insulation with Micrometeoroid Protection

Ultra-low-density, highly hydrophobic, fiber-reinforced aerogel material integrated with MLI (aluminized Mylar reflectors and B4A Dacron separators) offers a highly effective insulation package by providing unsurpassed thermal performance and significant robustness, delivering substantial MMOD protection via the addition of a novel, durable, external aerogel layer. The hydrophobic nature of the aerogel is an important property for maintaining thermal performance if the material is exposed to the environment (i.e. rain, snow, etc.) during ground installations. The hybrid aerogel/MLI/MMOD solution affords an attractive alternative because it will perform thermally in the same range as MLI at all vacuum levels (including high vacuum), and offers significant protection from micrometeoroid damage. During this effort, the required low-density and resilient aerogel materials have been developed that are needed to optimize the thermal performance for space (high vacuum) cryotank applications. The proposed insulation/MMOD package is composed of two sections: a stack of interleaved aerogel layers and MLI intended for cryotank thermal insulation, and a 1.5- to 1-in. (.2.5- to 3.8- cm) thick aerogel layer (on top of the insulation portion) for MMOD protection. Learning that low-density aerogel cannot withstand the hypervelocity impact test conditions, the innovators decided during the course of the program to fabricate a high-density and strong material based on a cross-linked aerogel (X-aerogel; developed elsewhere by the innovators) for MMOD protection. This system has shown a very high compressive strength that is capable of withstanding high-impact tests if a proper configuration of the MMOD aerogel layer is used. It was learned that by stacking two X-aerogel layers [1.5-in. (.3.8-cm) thick] separated by an air gap, the system would be able to hold the threat at a speed of 5 km/s and gpass h the test. The first aerogel panel stopped the projectile from damaging the second aerogel panel. The impacted X-aerogel (the back specimen from the successful test) was further tested in comparison to another similar sample (not impacted) at Kennedy Space Center for thermal conductivity evaluation at cryogenic conditions. The specimens were tested under high vacuum and cryogenic temperatures, using Cryostat 500. The results show that the specimen did not lose a significant amount of thermal performance due to the impact test, especially at high vacuum.

Begag, Redouane↗
NASA NTRS2004

Acoustic Emission Detection of Impact Damage on Space Shuttle Structures

The loss of the Space Shuttle Columbia as a result of impact damage from foam debris during ascent has led NASA to investigate the feasibility of on-board impact detection technologies. AE sensing has been utilized to monitor a wide variety of impact conditions on Space Shuttle components ranging from insulating foam and ablator materials, and ice at ascent velocities to simulated hypervelocity micrometeoroid and orbital debris impacts. Impact testing has been performed on both reinforced carbon composite leading edge materials as well as Shuttle tile materials on representative aluminum wing structures. Results of these impact tests will be presented with a focus on the acoustic emission sensor responses to these impact conditions. These tests have demonstrated the potential of employing an on-board Shuttle impact detection system. We will describe the present plans for implementation of an initial, very low frequency acoustic impact sensing system using pre-existing flight qualified hardware. The details of an accompanying flight measurement system to assess the Shuttle s acoustic background noise environment as a function of frequency will be described. The background noise assessment is being performed to optimize the frequency range of sensing for a planned future upgrade to the initial impact sensing system.

Prosser, William H.↗
DOE OSTI2023

Multifunctional Fiber-Reinforced Polymer Composites for Damage Detection and Memory

Self-structural health monitoring (SHM) functionalities for fiber-reinforced polymer composites have become highly sought after to ensure the structural safety of newly advancing components in the automotive, civil, mechanical, and aerospace industries. This paper introduces a self-damage detection and memory (SDDM) hybrid composite material, where the structural carbon fiber tow is transformed into a piezoresistive sensor network, and the structural glass fiber operates as electrical insulation. In this study, SDDM specimens were fabricated, and tensile and impact tests were performed. The tensile tests of SDDM specimens find two distinct loading peaks: first where the carbon fiber fails, and second where the glass fiber fails. A linear correlation was observed between the carbon fiber resistance and composite strain up to a threshold, beyond which a sharp nonlinear increase in resistance occurred. The resistance then approached infinity, coinciding with the first loading peak and failure of the carbon fiber elements. This demonstrates the potential for a damage early warning threshold. Additionally, the effect of stitching the sensor tow in a zig-zag pattern over a large area was investigated using tailored fiber placement (TFP) of 1-loop, 3-loop, and 5-loop specimens. Tensile testing found that increasing the number of loops improved the sensor’s accuracy for strain sensing. Furthermore, impact tests were conducted, and as the impact energy progressively increased, the sensor resistance permanently increased. This illustrates a capability for self-memory of microdamage throughout the life cycle of the structure, potentially useful for predicting the remaining life of the composite.

Demo, Luke B. (ORCID:0000000208806522)↗
NASA NTRS1998

A Passive Earth-Entry Capsule for Mars Sample Return

A combination of aerodynamic analysis and testing, aerothermodynamic analysis, structural analysis and testing, impact analysis and testing, thermal analysis, ground characterization tests, configuration packaging, and trajectory simulation are employed to determine the feasibility of an entirely passive Earth entry capsule for the Mars Sample Return mission. The design circumvents the potential failure modes of a parachute terminal descent system by replacing that system with passive energy absorbing material to cushion the Mars samples during ground impact. The suggested design utilizes a spherically blunted 45 degree half-angle forebody with an ablative heatshield. The primary structure is a spherical composite sandwich enclosing carbon foam energy absorbing material. Though no demonstration test of the entire system is included, results of the testing and analysis presented indicate that the design is a viable option for the Mars Sample Return Mission.

Mitcheltree, R. A.↗
NASA NTRS1999

A Passive Earth-Entry Capsule for Mars Sample Return

A combination of aerodynamic analysis and testing, aerothermodynamic analysis, structural analysis and testing, impact analysis and testing, thermal analysis, ground characterization tests, configuration packaging, and trajectory simulation are employed to determine the feasibility of an entirely passive Earth entry capsule for the Mars Sample Return mission. The design circumvents the potential failure modes of a parachute terminal descent system by replacing that system with passive energy absorbing material to cushion the Mars samples during ground impact. The suggested design utilizes a spherically blunted 45-degree half-angle cone forebody with an ablative heat shield. The primary structure is a hemispherical, composite sandwich enclosing carbon foam energy absorbing material. Though no demonstration test of the entire system is included, results of the tests and analysis presented indicate that the design is a viable option for the Mars Sample Return Mission.

Mitcheltree, Robert A.↗
NASA NTRS2015

Multi-Shock Shield Performance at 15 MJ for Catalogued Debris

While orbital debris of ten centimeters or more are tracked and catalogued, the difficulty of finding and accurately accounting for forces acting on the objects near the ten centimeter threshold results in both uncertainty of their presence and location. These challenges result in difficult decisions for operators balancing potential costly operational approaches with system loss risk. In this paper, the assessment of the feasibility of protecting a spacecraft from this catalogued debris is described using numerical simulations and a test of a multi-shock shield system against a cylindrical projectile impacting normal to the surface with approximately 15 MJ of kinetic energy. The hypervelocity impact test has been conducted at the Arnold Engineering Development Complex (AEDC) with a 598 g projectile at 6.905 km/s on a NASA supplied multi-shock shield. The projectile used is a hollow aluminum and nylon cylinder with an outside diameter of 8.6 cm and length of 10.3 cm. Figure 1 illustrates the multi-shock shield test article, which consisted of five separate bumpers, four of which are fiberglass fabric and one of steel mesh, and two rear walls, each consisting of Kevlar fabric. The overall length of the test article was 2.65 m. The test article was a 5X scaled-up version of a smaller multi-shock shield previously tested using a 1.4 cm diameter aluminum projectile for an inflatable module project. The distances represented by S1 and S1/2 in the figure are 61 cm and 30.5 cm, respectively. Prior to the impact test, hydrodynamic simulations indicated that some enhancement to the standard multi-shock system is needed to address the effects of the cylindrical shape of the projectile. Based on the simulations, a steel mesh bumper has been added to the shield configuration to enhance the fragmentation of the projectile. The AEDC test occurred as planned, and the modified NASA multi-shock shield successfully stopped 598 g projectile using 85.6 kg/m(exp 2). The fifth bumper layer remained in tact, although it was torn free from its support structure and thrown into the first rear wall. The outer Kevlar layer of the first rear wall tore likely from the impact of the fifth bumper's support structure, but the back of the rear wall was intact. No damage occurred to the second rear wall, or to the witness plate behind the target.

Miller, J. E.↗