Search NASA⌕ Search

SEARCH · Search NASA

Results for “Impact testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Room-Temperature Charpy Impact Property of 3D-Printed 15-5 Stainless Steel

In this study, the room-temperature Charpy impact property of 3D-printed 15-5 stainless steel was investigated by a combined experimental and finite element modeling approach. The experimentally measured impact energy is 10.85 ± 1.20 J/cm{sup 2}, which is comparable to the conventionally wrought and non-heat treated 15-5 stainless steel. In parallel to the impact test experiment, a finite element model using the Johnson–Cook material model with damage parameters was developed to simulate the impact test. The simulated impact energy is 10.46 J/cm{sup 2}, which is in good agreement with the experimental data. The fracture surface from the experimentally tested specimen suggests that the 3D-printed specimens undergo predominately brittle fracture.

36 MATERIALS SCIENCE↗

Impact reactivity of materials at very high oxygen pressure

The requirements for impact testing of materials in an oxygen atmosphere at pressures from 82.7 MPa (12,000 psi) to 172 MPa (25,000 psi) were evaluated. The impact tester system was evaluated for potential pressure increases from 69 MPa (10,000 psi) to 82.7 MPa (12,000 psi). The low pressure oxygen and nitrogen systems, the impact tower, the impact test cell, and the high pressure oxygen system were evaluated individually. Although the structural integrity of the impact test cell and the compressor were sufficient for operation at 82.7 MPa (12,000 psi), studies revealed possible material incompatibility at that pressure and above. It was recommended that if a component should be replaced for 82.7 MPa (12,000 psi) operation the replacement should meet the final objectives of 172 MPa (25,000 psi). Recommended changes in the system include; use of Monel 400 for pressures above 82.7 MPa (12,000 psi), use of bellows to replace the seal in the impact tester, use of a sapphire window attached to a fiber optic for event sensing, and use of a three diaphragm compressor.

Connor, H. W.↗

Development of Guidelines for In-Situ Repair of SLS-Class Composite Flight Hardware

The purpose of composite repair development at KSC (John F. Kennedy Space Center) is to provide support to the CTE (Composite Technology for Exploration) project. This is a multi-space center effort with the goal of developing bonded joint technology for SLS (Space Launch System) -scale composite hardware. At KSC, effective and efficient repair processes need to be developed to allow for any potential damage to composite components during transport or launch preparation. The focus of the composite repair development internship during the spring of 2018 was on the documentation of repair processes and requirements for process controls based on techniques developed through hands-on work with composite test panels. Three composite test panels were fabricated for the purpose of repair and surface preparation testing. The first panel included a bonded doubler and was fabricated to be damaged and repaired. The second and third panels were both fabricated to be cut into lap-shear samples to test the strength of bond of different surface preparation techniques. Additionally, jointed composite test panels were impacted at MSFC (Marshall Space Flight Center) and analyzed for damage patterns. The observations after the impact tests guided the repair procedure at KSC to focus on three repair methods. With a finalized repair plan in place, future work will include the strength testing of different surface preparation techniques, demonstration of repair methods, and repair of jointed composite test panels being impacted at MSFC.

Weber, Thomas P., Jr.↗

An Imaging System for Satellite Hypervelocity Impact Debris Characterization

This paper discusses the design of an automated imaging system for size characterization of debris produced by the DebriSat hypervelocity impact test. The goal of the DebriSat project is to update satellite breakup models. A representative LEO satellite, DebriSat, was constructed and subjected to a hypervelocity impact test. The impact produced an estimated 85,000 debris fragments. The size distribution of these fragments is required to update the current satellite breakup models. An automated imaging system was developed for the size characterization of the debris fragments. The system uses images taken from various azimuth and elevation angles around the object to produce a 3D representation of the fragment via a space carving algorithm. The system consists of N point-and-shoot cameras attached to a rigid support structure that defines the elevation angle for each camera. The debris fragment is placed on a turntable that is incrementally rotated to desired azimuth angles. The number of images acquired can be varied based on the desired resolution. Appropriate background and lighting is used for ease of object detection. The system calibration and image acquisition process are automated to result in push-button operations. However, for quality assurance reasons, the system is semi-autonomous by design to ensure operator involvement. This paper describes the imaging system setup, calibration procedure, repeatability analysis, and the results of the debris characterization.

Moraguez, Matthew↗

Fatigue Testing of Metallurgically-Bonded EBR-II Superheater Tubes

Fatigue crack growth and impact tests were performed on 2¼Cr-1Mo steel specimens machined from ex-service Experimental Breeder Reactor – II (EBR-II) superheater duplex tubes. The tubes had been metallurgically bonded with a 100 µm thick Ni layer; the specimens incorporated this bond layer. Impact tests were performed at temperatures from –50 to 400°C; cracks propagating from the V-notch were arrested by delamination at the bond layer for all tests with one exception at –50°C. Fatigue crack growth tests were performed at room temperature in air and at 400°C in air and humid Ar; cracks were grown at varied levels of constant ?K. In all conditions the presence of the Ni bond layer was found to result in a net retardation of growth as the crack passed through the layer. The mechanism of retardation was identified as a disruption of crack planarity and uniformity after passing through the porous bond layer. Full crack arrest was only observed in a single test performed at near-threshold ?K level (12 MPa?m) at 400°C. In this case the crack tip was blunted by oxidation of the base steel at the steel-nickel interface.

36 MATERIALS SCIENCE↗

PRELIMINARY ASSESSMENT OF NDE METHODS ON INSPECTION OF HDPE BUTT FUSION PIPING JOINTS FOR LACK OF FUSION

Studies at the Pacific Northwest National Laboratory in Richland, Washington, are being conducted to evaluate nondestructive examination approaches for inspecting butt fusion joints in high density polyethylene (HDPE) pipe for lack of fusion (LOF). The work provides information to the United States Nuclear Regulatory Commission on the effectiveness and need for volumetric inspection techniques of HDPE butt fusion joints in Section III, Division 1, Class 3, buried piping systems in nuclear power plants. This paper describes results from preliminary assessments using ultrasonic nondestructive techniques and high-speed tensile impact testing for determining joint integrity. A series of butt joints were fabricated in 3408, 12-inch IPS DR-11 material by varying the fusion parameters in attempts to provide good joints and joints containing LOF. These butt joints were visually examined and volumetrically examined with time-of-flight diffraction (TOFD) and phased-array (PA) ultrasound. A limited subset of pipe joint material was destructively analyzed by either slicing through the joint and visually examining the surface or by employing a standard high-speed tensile impact test. Initial correlation of the fusion parameters, nondestructive, and destructive evaluations have shown that areas with gross LOF were detected with both TOFD and PA ultrasound and that the tensile impact test showed a brittle failure at the joint. There is still some ambiguity in results from the less obvious LOF conditions. Current work is targeted on assessing the sensitivity of the ultrasonic volumetric examinations and validating the results with a destructive analysis. It is expected that on-going and future work will lead to quantifying the ultrasonic responses in terms of joint integrity.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DAMAGE DEVELOPMENT IN HIGH PURITY COPPER UNDER VARYING DYNAMIC CONDITIONS AND MICROSTRUCTURAL STATES USING CONTINUUM DAMAGE MECHANICS

In the framework of CDM, the evolution of the plastic strain, at which damage processes initiates, as a function of stress triaxiality, making the assumption of constant damage dissipated work is derived. Based on this, the CDM model proposed by Bonora (Eng. Frac. Mech., 58, 1-2, 1997) has been used to predict the occurrence of ductile failure at different stress triaxiality conditions, under both quasi-static and dynamic loading conditions. This solution allows the possibility to correctly predict the conditions for which ductile damage can initiate under uniaxial strain (such as that for the flyer plate impact test) and mixed conditions such as those in the Taylor impact test. The solution offers the possibility to correlate continuum damage model parameters to micro structural features such as grain size and purity grade.

36 MATERIALS SCIENCE↗

Data Mining of Historical Human Data to Assess the Risk of Injury due to Dynamic Loads

The NASA Occupant Protection Group is charged with ensuring crewmembers are protected during all dynamic phases of spaceflight. Previous work with outside experts has led to the development of a definition of acceptable risk (DAR) for space capsule vehicles. The DAR defines allowable probability rates for various categories of injuries. An important question is how to validate these probabilities for a given vehicle. One approach is to impact test human volunteers under projected nominal landing loads. The main drawback is the large number of subject tests required to attain a reasonable level of confidence that the injury probability rates would meet those outlined in the DAR. An alternative is to mine existing databases containing human responses to impact. Testing an anthropomorphic test device (ATD) at the same human‐exposure levels could yield a range of ATD responses that would meet DAR. As one aspect of future vehicle validation, the ATD could be tested in the vehicle's seat and suit configuration at nominal landing loads and compared with the ATD responses supported by the human data set. This approach could reduce the number of human‐volunteer tests NASA would need to conduct to validate that a vehicle meets occupant protection standards. METHODS: The U.S. Air Force has recorded hundreds of human responses to frontal, lateral, and spinal impacts at many acceleration levels and pulse durations. All of this data are stored on the Collaborative Biomechanics Data Network (CBDN), which is maintained by the Wright Patterson Air Force Base (WPAFB). The test device for human occupant restraint (THOR) ATD was impact tested on WPAFB's horizontal impulse accelerator (HIA) matching human‐volunteer exposures on the HIA to 5 frontal and 3 spinal loading conditions. No human injuries occurred as a result of these impact conditions. Peak THOR response variables for neck axial tension and compression, and thoracic‐spine axial compression were collected. Maximal chest deflection was determined from motion capture video of the impact test. HIC‐ 15 and BRIC were calculated from head acceleration responses. Given the number of human subjects for each test condition a confidence interval of injury probability will be obtained. RESULTS: Results will be discussed in terms of injury‐risk probability estimates based on the human data set evaluated. Also, gaps in the data set will be identified. These gaps could be one of two types. One is areas where additional THOR testing would increase the comparable human data set, thereby improving confidence in the injury probability rate. The other is where additional human testing would assist in obtaining information on other acceleration levels or directions. DISCUSSION: The historical human data showed validity of the THOR ATD for supplemental testing. The historical human data are limited in scope, however. Further data are needed to characterize the effects of sex, age, anthropometry, and deconditioning due to spaceflight on risk of injury

Wells, Jesica↗

Statistical Approach on Utilizing Ground-based Experiments to Model Break-up Events

Two laboratory-based impact tests have been conducted to develop and extend the capability of NASA satellite breakup models. The first experiment, the Satellite Orbital Debris Characterization Impact Test (SOCIT), was conducted by the U.S. Department of Defense and NASA in 1992. It employed a fully functional U.S. Navy Transit spacecraft, fabricated from materials commonly used in the 1960s. SOCIT fragmentation data formed the basis of the current NASA Standard Satellite Breakup Model (SSBM). A second experiment, DebriSat, was conducted in 2014 by the DebriSat consortium: the NASA Orbital Debris Program Office; the United States Space Force Space Systems Command, formerly the Air Force Space and Missile Systems Center, the Air Force Arnold Engineering Development Complex, and the University of Florida. This impact test was performed on a high-fidelity mock-up satellite assembled from modern components. Data from both experiments are expected to contribute to the next-generation models for on-orbit breakup analyses, long-term environment predictions, and debris risk assessment. This paper uses the direct statistical sampling of the SOCIT and DebriSat data ensembles to model an on-orbit breakup event, rather than the analytic expressions estimated from the samples as with as with the NASA SSBM and its predecessor. This direct method involves drawing fragments (i.e., sampling with replacement) from each fragmentation data-subset containing mass, shape category, material density, characteristic length, mass, and cross-sectional area. As part of the sampling process, the properties of sampled fragment data (e.g., area-to-mass ratios) are numerically checked to ensure they do not contain unrealistic quantities. The process to simulate a breakup cloud composed of fragments from SOCIT and DebriSat datasets is discussed. The methodology for ensuring that conservation of overall mass of the sampled fragment cloud under this sampling approach is highlighted. Finally, the results are compared with simulated clouds generated from SSBM for specific historical breakup events.

Andrew Vavrin↗

Statistical Approach on Utilizing Ground-Based Experiments to Model Break-Up Events

Two laboratory-based impact tests have been conducted to develop and extend the capability of NASA satellite breakup models. The first experiment, the Satellite Orbital Debris Characterization Impact Test (SOCIT), was conducted by the U.S. Department of Defense and NASA in 1992. It employed a fully functional U.S. Navy Transit spacecraft, fabricated from materials commonly used in the 1960s. SOCIT fragmentation data formed the basis of the current NASA Standard Satellite Breakup Model (SSBM). A second experiment, DebriSat, was conducted in 2014 by the DebriSat consortium: the NASA Orbital Debris Program Office, the United States Space Force Space Systems Command, formerly the Air Force Space and Missile Systems Center, the Air Force Arnold Engineering Development Complex, and the University of Florida. This impact test was performed on a high-fidelity mock-up satellite assembled from modern components. Data from both experiments are expected to contribute to the next-generation models for on-orbit breakup analyses, long-term environment predictions, and debris risk assessment. This paper uses the direct statistical sampling of the SOCIT and DebriSat data ensembles to model an on-orbit breakup event, rather than the analytic expressions estimated from the samples in the SSBM and its predecessor. This direct method involves drawing fragments (i.e., sampling with replacement) from each fragmentation data-subset containing mass, shape category, material density, characteristic length, mass, and cross-sectional area. As part of the sampling process, the properties of sampled fragment data (e.g., area-to-mass ratios) are numerically checked to ensure they do not contain unrealistic quantities. The process to simulate a breakup cloud composed of fragments from SOCIT and DebriSat datasets is discussed. The methodology for ensuring that conservation of overall mass of the sampled fragment cloud under this sampling approach is highlighted. Finally, the results are compared with simulated clouds generated from SSBM for specific historical breakup events.

Andrew Vavrin↗

Design, Fabrication and Test of Multi-Fiber Laminates

Unidirectional and angleply multifiber laminates were tested for improved impact strength and other mechanical properties. The effects of several variables on the mechanical properties of epoxy matrix materials were described. These include fiber type (HMS and AS graphites, glass, and Kevlar 49), ratio of primary to hybridizing fiber and hybrid configuration. It is demonstrated that AS graphite/S glass in an intraply configuration results in the best combination of static and Charpy impact properties as well as superior ballistic impact resistance. Pendulum impact tests which were conducted on thin specimens are shown to produce different ranking of materials than tests conducted on standard thickness Charpy specimens. It is shown that the thin specimen results are in better agreement with the ballistic impact data. Additional static test data are reported as a function of temperature for the seven best hybrid configurations having epoxy, polyimide (PMR-15) and polyphenylquinoxaline resins as the matrix.

Pike, R. A.↗

Damage Simulation in Composite Materials: Why It Matters and What Is Happening Currently at NASA in This Area

Use of lightweight composite materials in space and aircraft structure designs is often challenging due to high costs associated with structural certification. Of primary concern in the use of composite structures is durability and damage tolerance. This concern is due to the inherent susceptibility of composite materials to both fabrication and service induced flaws. Due to a lack of general industry accepted analysis tools applicable to composites damage simulation, a certification procedure relies almost entirely on testing. It is this reliance on testing, especially compared to structures comprised of legacy metallic materials where damage simulation tools are available, that can drive costs for using composite materials in aerospace structures. The observation that use of composites can be expensive due to testing requirements is not new and as such, research on analysis tools for simulating damage in composite structures has been occurring for several decades. A convenient approach many researchers/model-developers in this area have taken is to select a specific problem relevant to aerospace structural certification and develop a model that is accurate within that scope. Some examples are open hole tension tests, compression after impact tests, low-velocity impact, damage tolerance of an embedded flaw, and fatigue crack growth to name a few. Based on the premise that running analyses is cheaper than running tests, one motivation that many researchers in this area have is that if generally applicable and reliable damage simulation tools were available the dependence on certification testing could be lessened thereby reducing overall design cost. It is generally accepted that simulation tools if applied in this manner would still need to be thoroughly validated and that composite testing will never be completely replaced by analysis. Research and development is currently occurring at NASA to create numerical damage simulation tools applicable to damage in composites. The Advanced Composites Project (ACP) at NASA Langley has supported the development of composites damage simulation tools in a consortium of aerospace companies with a goal of reducing the certification time of a commercial aircraft by 30%. And while the scope of ACP does not include spacecraft, much of the methodology and simulation capabilities can apply to spacecraft certification in the Space Launch System and Orion programs as well. Some specific applications of composite damage simulation models in a certification program are (1) evaluation of damage during service when maintenance may be difficult or impossible, (2) a tool for early design iterations, (3) gaining insight into a particular damage process and applying this insight towards a test coupon or structural design, and (4) analysis of damage scenarios that are difficult or impossible to recreate in a test. As analysis capabilities improve, these applications and more will become realized resulting in a reduction in cost for use of composites in aerospace vehicles. NASA is engaged in this process from both research and application perspectives. In addition to the background information discussed previously, this presentation covers a look at recent research at NASA in this area and some current/potential applications in the Orion program.

McElroy, Mack↗

Effect of fiber diameter and matrix alloys on impact-resistant boron/aluminum composites

Efforts to improve the impact resistance of B/Al are reviewed and analyzed. Nonstandard thin-sheet charpy and Izod impact tests and standard full-size Charpy impact tests were conducted on composites containing unidirectional 0.10mm, 0.14mm, and 0.20mm diameter boron fibers in 1100, 2024, 5052, and 6061 Al matrices. Impact failure modes of B/Al are proposed in an attempt to describe the mechanisms involved and to provide insight for maximizing impact resistance. The impact strength of B/Al was significantly increased by proper selection of materials and processing. The use of a ductile matrix and large diameter boron fibers gave the highest impact strengths. This combination resulted in improved energy absorption through matrix shear deformation and multiple fiber breakage.

Mcdanels, D. L.↗

Neural Networks Analyze Data In Particle-Impact-Noise Tests

Electronic neural networks and computers put to use in analyzing data acquired in particle-impact-noise-detection (PIND) tests of packaged electronic components. PIND tests detect loose particles in packages that cause failures during subsequent operation of packages in presence of accelerations or other effects - for example, loose electrically conductive particles that bounce into positions in which they cause short circuits. Interpretation of test data more objective and accurate. Preliminary results suggest use of neural networks result in significant improvement in quality and reliability and decrease in cost of PIND testing.

Scaglione, Lois J.↗

Analysis of the DebriSat Fragments and Comparison to the NASA Standard Satellite Breakup Model

Existing DOD and NASA satellite breakup models are based on a key laboratory test, the 1992 Satellite Orbital debris Characterization Impact Test, which has supported many applications and matched on-orbit events involving older satellite designs reasonably well over the years. In 2014, the NASA Orbital Debris Program Office, in collaboration with the Air Force Space and Missile Systems Center, The Aerospace Corporation, and the University of Florida, conducted a hypervelocity impact test using a high-fidelity, mock-up satellite, DebriSat, in controlled and instrumented laboratory conditions to update and improve these models. DebriSat is representative of present-day, low Earth orbit satellites, having been constructed with modern spacecraft materials and techniques. The DebriSat fragment ensemble provided a variety of shapes, bulk densities, and dimensions. Fragments down to 2 mm in size are being characterized by their physical and derived properties. The data will inform updates to the current NASA Standard Satellite Breakup Model (SSBM), which was formulated using laboratory and ground-based measurements of on-orbit fragmentation events to describe an average breakup for spacecraft and upper-stage collisions and explosions. Although individual fragment collection and characterization is still ongoing, this paper will present the status of the DebriSat fragment data analysis including cumulative characteristic length and cumulative mass distributions, area-to-mass distributions, and characteristic length versus mass distributions. Additionally, comparisons to the NASA SSBM will be presented.

Murray, James↗

Groundwater Remediation and Alternate Energy at White Sands Test Facility

White Sands Test Facility Core Capabilities: a) Remote Hazardous Testing of Reactive, Explosive, and Toxic Materials and Fluids; b) Hypergolic Fluids Materials and Systems Testing; c) Oxygen Materials and System Testing; d) Hypervelocity Impact Testing; e)Flight Hardware Processing; and e) Propulsion Testing. There is no impact to any drinking water well. Includes public wells and the NASA supply well. There is no public exposure. Groundwater is several hundred feet below ground. No air or surface water exposure. Plume is moving very slowly to the west. Plume Front Treatment system will stop this westward movement. NASA performs on-going monitoring. More than 200 wells and zones are routinely sampled. Approx. 850 samples are obtained monthly and analyzed for over 300 different hazardous chemicals.

Fischer, Holger↗

Development and Evaluation of Stitched Sandwich Panels

This study explored the feasibility and potential benefits provided by the addition of through-the-thickness reinforcement to sandwich structures. Through-the-thickness stitching is proposed to increase the interlaminar strength and damage tolerance of composite sandwich structures. A low-cost, out-of-autoclave processing method was developed to produce composite sandwich panels with carbon fiber face sheets, a closed-cell foam core, and through-the-thickness Kevlar stitching. The sandwich panels were stitched in a dry preform state, vacuum bagged, and infiltrated using Vacuum Assisted Resin Transfer Molding (VARTM) processing. For comparison purposes, unstitched sandwich panels were produced using the same materials and manufacturing methodology. Test panels were produced initially at the University of Utah and later at NASA Langley Research Center. Four types of mechanical tests were performed: flexural testing, flatwise tensile testing, core shear testing, and edgewise compression testing. Drop-weight impact testing followed by specimen sectioning was performed to characterize the damage resistance of stitched sandwich panels. Compression after impact (CAI) testing was performed to evaluate the damage tolerance of the sandwich panels. Results show significant increases in the flexural stiffness and strength, out-of-plane tensile strength, core shear strength, edgewise compression strength, and compression-after-impact strength of stitched sandwich structures.

Stanley, Larry E.↗

Orbital Debris Shape Effect Investigations for Mitigating Risk

NASA’s Orbital Debris Program Office (ODPO) and Hypervelocity Impact Technology (HVIT) team have coordinated to better understand the risks to upper stages and spacecraft from non-spherical orbital debris. It is well understood that fragmentation (collision or explosion) events in orbit produce fragments of various materials, sizes, and shapes. To further characterize these parameters, the ODPO is developing the next-generation Orbital Debris Engineering Model (ORDEM) version 4.0 to include orbital debris shape distributions. Ground-based assets, such as radar and optical sensors, can provide size estimates and some insight into material based on radar return or optical filter photometry/spectroscopy, respectively. Characterizing an object’s shape requires more laboratory analyses to infer how shape affects these measurements. More importantly, in addition to size and material/density, the shape of fragments in orbit will alter the ballistic limit equations used in orbital debris risk assessments with NASA’s Bumper Code. The ODPO plans to release ORDEM 4.0 in the coming years. Performing ground-based laboratory impact tests on high-fidelity spacecraft mockups provides the means to directly measure size, mass, material/density, and shape of fragments, all key parameters needed to characterize real-world break up events. The DebriSat test, the results of which are provided, showcases the details of this type of experiment. The goal of this collaborative research between the ODPO and the HVIT team is to include a shape parameter in the environmental and breakup models used to assess risk for various space structures. This paper examines ground-based laboratory impact tests and the associated fragment shape categories. Provided these defined shapes, the approach is simplified by assuming a right circular cylinder (RCC) approximation with varying length-to-diameter ratios. Highlights of impact tests conducted by the HVIT team using non-spherical projectiles based on the RCC approximation are presented. Hydrocode simulations have also been performed to expand on the complexity of variations with non-spherical projectiles. Lastly, ray-tracing simulations of various RCCs of known material are provided to support the ongoing research on optical reflectance distributions with known shapes and to highlight how this may modify the current optical size estimation model. The status and plan forward are outlined for NASA's orbital debris shape effect investigation using a multidisciplinary approach by the ODPO and the HVIT team.

Heather Cowardin↗