Search NASA⌕ Search

SEARCH · Search NASA

Results for “In situ characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Utah FORGE 2439: A Multi-Component Approach to Characterizing In-Situ Stress

Core-based in-situ stress estimation, Triaxial Ultrasonic Velocity (labTUV) data, and Deformation Rate Analysis (DRA) data for Utah FORGE well 16A(78)-32 using triaxial ultrasonic velocity and deformation rate analysis. Report documenting a multi-component approach to characterizing in-situ stress at the U.S. DOE FORGE EGS site: laboratory, modeling and field measurement. Core-based methods for in-situ stress estimation were applied using samples from 5 intervals within the Utah FORGE 16A(78)-32 well. At three of these locations, Triaxial Ultrasonic Velocity (labTUV) tests were performed, resulting in experimentally-determined relationships between wave velocities and stresses. Non-monotonic increase in the velocity-stress relationships are inferred provide evidence of stress history and are therefore used to estimate in-situ stress magnitudes. Additionally, Deformation Rate Analysis (DRA) tests were run on core plugs from various orientations at each of the 5 sampling locations. These, too, provide evidence of stress history based on stress-strain behavior. A novel Weight of Evidence (WoE) method was developed as a means of synthesizing in-situ stress evidence from these two types of tests. Results indicate the minimum horizontal stress gradient ranges from 0.58 psi/ft to 0.69 psi/ft, with 4 of the 5 values between 0.66 psi/ft and 0.69 psi/ft. The vertical stress gradient ranges from 1.05 psi/ft to 1.12 psi/ft, with 4 of the 5 zones given results between 1.09 psi/ft and 1.12 psi/ft. The maximum horizontal stress gradient ranges from 0.98 psi/ft to 1.34 psi/ft, with 4 of the 5 zones falling between 0.98 psi/ft and 1.24 psi/ft. The stress regime thus appears to be on the edge between normal faulting and strike-slip faulting, potentially flipping back and forth between the two regimes due to variability of rock properties, structures such as faults, and/or thermal anomalies.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

In situ temperature synthesis and characterization of ferroelectric PZN-4.5PT nanoparticles’ thin films using synchrotron light source

Despite the excellent properties of Pb(Zn 1/3 Nb 2/3 )O 3 -4.5PbTiO 3 (PZN-4.5PT) single crystals, the greatest difficulty for their application on electronic devices is to make them to thin layers related to the difficulty to make them as ceramic materials. In this paper, we use the combined USAXS/SAXS/WAXS instrument at 9ID beamline at APS-ANL for in situ characterization of PZN-4.5PT inorganic perovskite nanoparticles thin films deposited on nanotextured silicon to understand the phase transitions and determine the observed microcrystals' structure. Here, the sample was annealed from ambient to 1000°C. The results revealed structure changes in the nanoparticles' thin films which could be explained by the new phase that can be assigned to the Pb 3 (PO 4 )2-based component. The peak at 31° indicates the presence of the rhombohedral phase perovskites assigned to the nanoparticles. WAXS characterization permitted to identification of many transitions during thermal annealing like dehydration or dihydroxylation of phosphorus gel -OH bonds and internal water.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Oxidation State and Surface Reconstruction of Cu under CO 2 Reduction Conditions from In Situ X-ray Characterization

The electrochemical CO 2 reduction reaction (CO 2 RR) using Cu-based catalysts holds great potential for producing valuable multi-carbon products from renewable energy. However, the chemical and structural state of Cu catalyst surfaces during the CO 2 RR remains a matter of debate. In this paper, we show the structural evolution of the near-surface region of polycrystalline Cu electrodes under in situ conditions through a combination of grazing incidence X-ray absorption spectroscopy (GIXAS) and X-ray diffraction (GIXRD). The in situ GIXAS reveals that the surface oxide layer is fully reduced to metallic Cu before the onset potential for CO 2 RR, and the catalyst maintains the metallic state across the potentials relevant to the CO 2 RR. We also find a preferential surface reconstruction of the polycrystalline Cu surface toward (100) facets in the presence of CO 2 . Quantitative analysis of the reconstruction profiles reveals that the degree of reconstruction increases with increasingly negative applied potentials, and it persists when the applied potential returns to more positive values. These findings show that the surface of Cu electrocatalysts is dynamic during the CO 2 RR, and emphasize the importance of in situ characterization to understand the surface structure and its role in electrocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Iron-Doped Sodium Vanadium Oxyflurophosphate Cathodes for Sodium-Ion Batteries—Electrochemical Characterization and In Situ Measurements of Heat Generation

Sodium-ion batteries (NaIBs) are increasingly being envisioned for grid-scale energy-storage systems because of cost advantages. However, implementation of this vision has been challenged by the low-energy densities delivered by most NaIB cathodes. Toward addressing this challenge, the authors report the synthesis and characterization of a new iron-doped Na 3 Fe 0.3 V 1.7 O(PO 4 ) 2 F 2 cathode using a novel facile hydrothermal route. The synthesized material was characterized using scanning electron microscopy, X-ray diffraction, and Mössbauer spectroscopy techniques. The obtained discharge capacity in the half-cell configuration lies from 119 to 125 to 130 mA h/g at C/10 while tested using three different electrolyte formulations, dimethyl carbonate–ethylene carbonate (EC)–propylene carbonate (PC), diethyl carbonate–EC, and EC–PC, respectively. The synthesized cathodes were also evaluated in full-cell configurations, which delivered an initial discharge capacity of 80 mA h/g with NaTi 2 (PO 4 ) 3 MWCNT as the anode. Ionic diffusivity and interfacial charge transfer kinetics were also evaluated as a function of temperature and sodium concentration, which revealed that electrochemical rate performances in this material were limited by charge-transfer kinetics. To understand the heat generation mechanism of the Na/Na 3 Fe 0.3 V 1.7 O(PO 4 ) 2 F 2 half-cell during charge and discharge processes, an electrochemical isothermal calorimetry measurement was carried out at different current rates for two different temperatures (25 and 45 °C). The results showed that the amount of heat generated was strongly affected by the operating charge/discharge state, C-rate, and temperature. Altogether, this work provides a new synthesis route for the development of iron-doped Na 3 Fe 0.3 V 1.7 O(PO 4 ) 2 F 2 -based high-performance sodium cathode materials aimed at providing a viable pathway for the development and deployment of large-scale energy-storage based on sodium battery systems.

25 ENERGY STORAGE↗
DOE OSTI2020

Synchrotron Catalysis Consortium (SCC) at NSLS-II: Dedicated Beamline Facilities for In Situ and Operando Characterization of Catalysts

The Synchrotron Catalysis Consortium (SCC) was funded and established in September 2005 at the National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory (BNL). For more than a decade, the SCC was the first of its kind in the United States, with a mission to promote the utilization of synchrotron techniques for cutting-edge catalysis research under in-situ conditions. The consortium consists of three Principal Investigators (Jingguang Chen, Columbia University, Anatoly Frenkel, Stony Brook University/BNL, and Jose Rodriguez, BNL) and scientific staff member Nebojsa Marinkovic. The initial team also included Radoslav Adzic, BNL, and collaborators from academic, national, and industrial laboratories. During the first decade of its operations at three NSLS beamlines (X18A, X18B, and X19A) until the closing of NSLS on September 30, 2014, the primary goal of the SCC team was to provide assistance and to develop new sciences/techniques to the catalysis community...This report outlines a brief history, specifications, techniques, and training and outreach for the facility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1998

Combining data from lidar and in situ instruments to characterize the vertical structure of aerosol optical properties

Over the last decade, the quantification of tropospheric aerosol abundance, composition and radiative impacts has become an important research endeavor. For the most part, the interest in tropospheric aerosols is derived from questions related to the global and local (instantaneous) radiative forcing of climate due to these aerosols. One approach is to study local forcing under well-defined conditions, and to extrapolate such results to global scales. To estimate local aerosol forcing, appropriate radiative transfer models can be employed (e.g., the Fu-Liou radiative transfer code, [Fu and Liou, 1993]). In general, such models require information on derived aerosol properties [Toon, 1994]; namely the aerosol optical depth, single-scattering albedo, and asymmetry factor (phase function), all of which appear in the equations of radiative transfer. In this paper, we report on a method that utilizes lidar data and in situ aerosol size distribution measurements to deduce the vertical structure of the aerosol complex index of refraction in the near IR, thus identifying the aerosol type. Together with aerosol size distributions obtained in situ, the aerosol refractive index can be used to calculate the necessary derived aerosol properties. The data analyzed here were collected during NASA's PEM West-B (Pacific Exploratory Mission) experiment, which took place in February/March 1994. The platform for the measurements was the NASA DC-8 aircraft. The primary goal of the PEM West missions [Browell et al., 1996] was the assessment of potential anthropogenic perturbations of the chemistry in the Pacific Basin troposphere. For this purpose the timing of PEM West-B corresponded to the seasonal peak in transport from the Asian continent into the Pacific basin [Merrill et al., in press]. This period normally occurs during Northern Hemisphere spring, when the Japan jet is well developed.

Redemann, J.↗
DOE OSTI2024

In-situ hydrogen microstructural characterization of Si heterojunction passivation: Addressing V OC degradation and mitigation pathways

Si heterojunction (SHJ) solar cells have demonstrated record efficiency >27%, approaching the theoretical limit of ≈ 29%, primarily due to best surface/interface defect passivation provided by deposited thin layers of hydrogenated amorphous silicon (a-Si:H). Such excellent surface/interface passivation reduces recombination loss and result in >100 mV improvement of cell open circuit voltage (V OC ) to ≈ 750 mV, thus the cell efficiency. However, fielded SHJ modules exhibit loss of V OC and hence efficiency over time in years, presumably due to degradation related to a-Si:H layers. This adversely affects the technology’s market acceptance, and levelized cost of energy (LCOE). It is hypothesized that the origin of a-Si:H degradation is somehow related to the presence of weak Si–Si bonds and hydrogen in a-Si:H films. The objective of this project is to test this hypothesis by directly measuring chemical and structural changes occurring within SHJ component layers and solar cells. This is achieved by developing an innovative in-situ Fourier transform infrared (FTIR) spectrometry apparatus to monitor hydrogen microstructural changes occurring within amorphous silicon and decipher hydrogen evolution kinetics over time when samples are exposed to heat and/or light stress. These in-situ measured hydrogen microstructural changes are correlated to the changes in effective minority carrier lifetime (τ eff ), implied V OC (iV OC ), surface recombination velocity (S), and cell V OC . These mechanistic understandings will provide critical guidance to mitigate the V OC -driven degradation of SHJ solar cell performance. Passivation optimization and degradation analysis of individual SHJ component structures were achieved through systematic deposition of three symmetric structures and the completed SHJ solar cell structure. The three symmetric structures used were intrinsic a-Si:H [(i)a-Si:H] layers in a bilayer structure, intrinsic and p-type doped stacked layers [(i-p)a-Si:H] representing the front heterojunction in the SHJ cell, and intrinsic and n-typed doped stacked layers [(i-n)a-Si:H] representing the back-side back surface field (BSF) in the SHJ cell. State-of-the-art passivation qualities are demonstrated by a champion iV OC of 740 mV for the (i)a-Si:H layers, and the (i-n)a-Si:H symmetric structure. A 725 mV iV OC is observed for the (i-p)a-Si:H symmetric structure. These symmetric passivated SHJ component structures were subsequently subjected to different accelerated lifetime (ALT) stressors to identify which conditions contribute the most to iV OC degradation. Degradation of the thin (10 nm) (i)a-Si:H passivation layers without any additional overlying layers is minimal; complexity of this study arises due to unavoidable surface oxidation of (i)a-Si:H layer during most of the stress application, which is likely irrelevant for a full SHJ cell configuration with overlying protective layers. The iV OC degradation of symmetric structures is found to occur primarily at the (i-p)a-Si:H passivation stack under dark heat stress with associated hydrogen loss from the (p)a-Si:H layer. An activation energy for increase in S (defect creation) of 0.65 eV can be correlated to the activation energy of ≈ 0.4 eV for hydrogen loss from the (i-p)a-Si:H stack. This also suggests the presence of weakly bonded hydrogen in the (p)a-Si:H films, which effuses out of the film stack at such low activation energy. When light and heat stress are applied together, similar hydrogen loss from (i-p)a-Si:H stack is observed, however, does not appreciably degrade iV OC or increase S. This is an important result and departure from direct correlation between hydrogen loss and defect creation. This perhaps indicates additional defect chemistries or annealing that might be occurring in the presence of light requiring further detailed defect measurements. The full SHJ cell structure used for this project is depicted in Fig.1(d). SHJ cells with an initial V OC ≈ 700 mV were fabricated and subjected to similar ALT stress conditions. Cell V OC is found to degrade the most under dark heat stress and is confirmed by observed hydrogen migration out of the (i-p)a-Si:H stack. However, hydrogen cannot escape from the cell stack, it accumulates near the (p)a-Si:H/ITO contact interface, where ITO acts as a barrier preventing hydrogen loss. Furthermore, light-heat combined stress does not degrade V OC appreciably, confirming the occurrence of a defect annealing process.

14 SOLAR ENERGY↗
NASA NTRS2004

In Situ Location and Characterization of Carbon-bearing Phases in Carbonaceous Chondrites: Insights from Yamato 791198, a Weakly-altered CM2 Chondrite

Intense studies of carbonaceous chondrites have provided remarkable insights into the behavior of carbon during the earliest stages of our solar system. This research has demonstrated that carbonaceous meteorites contain a diverse array of organic compounds, whose origins are probably the result of multiple processes that occurred in different locations including interstellar space, the solar nebula and asteroidal parent bodies [1-3]. The most abundant organic carbon component in CI1 and CM2 carbonaceous chondrites is so-called macromolecular carbon, a high molecular weight material that has some affinities to terrestrial kerogen and constitutes approximately 60-70% of the organic material in these meteorites. Although recent studies e.g. [3] have radically improved our understanding of the structural and compositional characteristics of this material, a number of key questions remain to be addressed. In particular, our knowledge of where this macromolecular material is distributed at the fine-scale within carbonaceous chondrites is scant. [4] have shown that organic material is associated with phyllosilicate-rich matrix in CM chondrites, but the detailed mineralogical associations are not well-known. Over the past 2 years, we have begun to address this question by using energy filtered transmission electron microscopy (EFTEM) to locate carbon-bearing materials in situ, focusing specifically on the CM2s. To date we have reported data on the Murchison CM2 chondrite [5], a meteorite that has experienced a modest degree of aqueous alteration. To extend our observations to other CM2 chondrites, we have examined the occurrence of carbon-bearing phases in Yamato 791198. Our recent studies [5] have shown that Y-791198 is among the most weakly-altered CM chondrite currently known and hence is likely to preserve a quite primitive distribution of carbonaceous material. In this study, we present initial observations on the distribution of these materials in one fine-grained rim and compare them with our results from Murchison. Such information may provide important insights into the origins of the carbonaceous material and how it was distributed in nebular and perhaps presolar dust.

Brearley, Adrian J.↗
DOE OSTI2023

Microstructure Evolution of a Multimodal Gamma-Prime Ni-Based Superalloy Characterized by In Situ Diffraction

The relationship between the evolution of microstructure, deformation micromechanisms and mechanical properties is difficult to establish in multimodal size distribution $_γ$$'$ superalloys, as the microstructure evolves with both temperature and time, and multiple strengthening mechanisms across each size distribution contribute to mechanical performance. In situ X-ray scattering can offer unparalleled insight regarding microstructure evolution at the temperatures and stresses of importance to gas-turbine applications; however, in situ X-ray diffraction has not been applied to the study of multimodal $_γ$$'$ distribution superalloys. Herein, lattice parameter evolution of secondary and tertiary $_γ$$'$ precipitates in a representative superalloy, Nimonic 115, is determined between 750 °C and 950 °C and correlated to room-temperature SEM and microhardness values. A large positive lattice parameter misfit of secondary $_γ$$'$ induces precipitate splitting, and the tertiary $_γ$$'$ goes into dissolution at ~ 800 °C, but with little apparent change in hardness values. The volume fraction of $_γ$$'$ decreases above 900 °C and precipitate-matrix coherency is lost, and there is a corresponding decrease in microhardness values. Importantly, the diffraction analysis demonstrates the capability to determine critical microstructural parameters of both precipitate size distributions in situ, representing an additional tool for determining microstructure-mechanical property relationships of multimodal superalloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Probing the surface of promoted CuO-Cr 2 O 3 -Fe 2 O 3 catalysts during CO 2 activation

The influence of basic oxide promoters on copper-chromium-iron oxide catalysts was investigated to determine the nature of surface oxygen species and structure-activity relationship for the reverse water-gas shift reaction. The catalysts were characterized with in situ XRD, in situ Raman, in situ XPS, in situ HS-LEIS and H 2 -TPR. Two surface oxygen sites with different reduction characteristics were found to be present. The overall CO 2 activation rate was found to correlate with both the number and reducibility of the more active oxygen species that were likely associated with the Cu-FeO x interfacial regions for enhanced hydrogen spillover. While addition of K 2 O somewhat preserved the interfacial regions and facilitated the reduction kinetics of surface oxygen, both Na 2 O and CaO significantly suppressed the availability of metallic Cu as well as the Cu-FeO x interfaces, leading to decreased reactivity. These findings provide a direction to promote the copper-iron catalysts by creating more metal-metal oxide interfacial sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electrical and structural characterization of in situ MOCVD Al2O3/β-Ga2O3 and Al2O3/β-(AlxGa1−x)2O3 MOSCAPs

This study investigates the electrical and structural properties of metal–oxide–semiconductor capacitors (MOSCAPs) with in situ metal-organic chemical vapor deposition-grown Al2O3 dielectrics deposited at varying temperatures on (010) β-Ga2O3 and β-(AlxGa1−x)2O3 films with different Al compositions. The Al2O3/β-Ga2O3 MOSCAPs exhibited a strong dependence of electrical properties on Al2O3 deposition temperature. At 900 °C, reduced voltage hysteresis (∼0.3 V) with improved reverse breakdown voltage (74.5 V) was observed, corresponding to breakdown fields of 5.01 MV/cm in Al2O3 and 4.11 MV/cm in β-Ga2O3 under reverse bias. In contrast, 650 °C deposition temperature resulted in higher voltage hysteresis (∼3.44 V) and lower reverse breakdown voltage (38.8 V) with breakdown fields of 3.69 and 2.87 MV/cm in Al2O3 and β-Ga2O3, respectively, but exhibited impressive forward breakdown field, increasing from 5.62 MV/cm at 900 °C to 7.25 MV/cm at 650 °C. High-resolution scanning transmission electron microscopy (STEM) revealed improved crystallinity and sharper interfaces at 900 °C, contributing to enhanced reverse breakdown performance. For Al2O3/β-(AlxGa1−x)2O3 MOSCAPs, increasing Al composition (x) from 5.5% to 9.2% reduced net carrier concentration and improved reverse breakdown field contributions from 2.55 to 2.90 MV/cm in β-(AlxGa1−x)2O3 and 2.41 to 3.13 MV/cm in Al2O3. The electric field in Al2O3 dielectric under forward bias breakdown also improved from 5.0 to 5.4 MV/cm as Al composition increased from 5.5% to 9.2%. The STEM imaging confirmed the compositional homogeneity and excellent stoichiometry of both Al2O3 and β-(AlxGa1−x)2O3 layers. These findings demonstrate the robust electrical performance, high breakdown fields, and excellent structural quality of Al2O3/β-Ga2O3 and Al2O3/β-(AlxGa1−x)2O3 MOSCAPs, highlighting their potential for high-power electronic applications.

Bhuiyan, A. F. M. Anhar Uddin (ORCID:0000000334212↗
DOE OSTI2022

Ductile failure and damage localization in Al6061-T6 characterized by in situ X-ray computed tomography and neural network segmentation

Damage initiation and localization in uniaxial tension tests of an Al6061-T6 alloy are evaluated and quantified using in situ X-ray computed tomography and a neural network segmentation strategy. This segmentation strategy offers significant advantages over traditional thresholding in quantifying microstructural and damage evolution metrics. Void nucleation was observed to occur throughout the deformation process, whereas void volume did not grow significantly until later stages of deformation. Localized analysis determined that void nucleation begins in and around the necked region during the early stages of deformation, whereas limited damage nucleation occurs outside of the neck until late stages of deformation. Lastly, inhomogeneities in void and particle spacing in the initial undeformed state of the material are observed to correlate well with the location of damage localization and necking during deformation. These results provide new insights into the ductile failure of Al alloys and how preexisting defects influence damage and rupture.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Windowless Optical Cell for In-Situ Molten Salt Characterization (Final CRADA Report)

This document serves as a summary report for the work conducted under CRADA 2021-21064 between Argonne National Laboratory and Xerion Advanced Battery Corp. As part of this project, Argonne and Xerion worked to develop a high-temperature version of the on-line optical analysis loop and evaluated its ability to facilitate Raman spectroscopy measurements on flowing molten salts relevant to Xerion’s process flowsheets. The main goals were to (1) achieve a geometrically smooth and stable meniscus at the molten salt and atmosphere interface by creating a slightly negative pressure in the flow channel at the aperture, (2) acquire Raman spectra of molten salt flowing across the aperture while maintaining consistent focus and protecting the optics from heat damage and direct contact with the molten salts, and (3) determine the impact of molten salt wicking and creep on the spectroscopy.

25 ENERGY STORAGE↗
DOE OSTI2020

In-situ active impedance characterization of scanned array antennas

Various embodiments presented herein relate to determining mutual coupling between a pair of antennas in an array antenna. Various operations presented herein enable comparison between a magnitude and phase of a signal transmitted from a first feed network (via a first antenna) and a magnitude and phase of a portion of the signal received at a second feed network (via a second antenna). Electrical effects engendered by any of the first feed network, a first switch, a first local circuit, the second feed network, a second switch, and a second local circuit can also be determined and their effects mathematically removed. Based upon the foregoing, a mutual coupling between the pair of antenna is determined.

42 ENGINEERING↗
DOE OSTI2022

Method and apparatus for real time, in situ sensing and characterization of roughness, geometrical shapes, geometrical structures, composition, defects, and temperature in three-dimensional manufacturing systems

Methods and apparatuses for manufacturing are disclosed, including (a) providing an apparatus having: a laser; scanner; powder injection system; powder spreading system; dichroic filter; imager-and-processor; and computer; (b) programming the computer with specifications of a sample; (c) using the computer to set initial parameters based on the sample specifications; (d) adjusting a stage to position the sample; (e) focusing and scanning electromagnetic radiation onto the sample while powder is concurrently injected onto the sample in order to deposit a layer; (f) capturing two-dimensional images of the sample and probing the sample to determine whether the deposited layer was manufactured per the specifications; (g) use the computer to adjust the three-dimensional manufacturing parameters based on the determination made in step (f) prior to additively manufacturing a subsequent layer or making repairs; and (h) repeating steps (d), (e), (f), and (g) until the manufacture is complete. Other embodiments are described and claimed.

Liu, Jian↗