Search NASA⌕ Search

SEARCH · Search NASA

Results for “Interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Advancing-side directivity and retreating-side interactions of model rotor blade-vortex interaction noise

Acoustic data are presented from a 40 percent scale model of the four-bladed BO-105 helicopter main rotor, tested in a large aerodynamic wind tunnel. Rotor blade-vortex interaction (BVI) noise data in the low-speed flight range were acquired using a traversing in-flow microphone array. Acoustic results presented are used to assess the acoustic far field of BVI noise, to map the directivity and temporal characteristics of BVI impulsive noise, and to show the existence of retreating-side BVI signals. The characterics of the acoustic radiation patterns, which can often be strongly focused, are found to be very dependent on rotor operating condition. The acoustic signals exhibit multiple blade-vortex interactions per blade with broad impulsive content at lower speeds, while at higher speeds, they exhibit fewer interactions per blade, with much sharper, higher amplitude acoustic signals. Moderate-amplitude BVI acoustic signals measured under the aft retreating quadrant of the rotor are shown to originate from the retreating side of the rotor.

Martin, R. M.↗
NASA NTRS1992

Environmental interactions in space exploration: Environmental interactions working group

With the advent of the Space Exploration Initiative, the possibility of designing and using systems on scales heretofore unattempted presents exciting new challenges in systems design and space science. The environments addressed by the Space Exploration Initiative include the surfaces of the Moon and Mars, as well as the varied plasma and field environments which will be encountered by humans and cargo enroute to these destinations. Systems designers will need to understand environmental interactions and be able to model these mechanisms from the earliest conceptual design stages through design completion. To the end of understanding environmental interactions and establishing robotic precursor mission requirements, an Environmental Interactions Working Group was established as part of the Robotic Missions Working Group. The working group is described, and its current activities are updated.

Kolecki, Joseph C.↗
NASA NTRS1991

The Solar Array Module Plasma Interactions Experiment (SAMPIE) - A Shuttle-based plasma interactions experiment

The Solar Array Module Plasma Interactions Experiment (SAMPIE), an approved Shuttle space flight experiment with a tentative launch date in July 1993, is intended to investigate plasma interactions of high-voltage space power systems. Solar cell modules, representing several technologies, will be biased to high voltages to characterize both arcing (negative potential) and current collection (positive potential). Other solar modules, specially modified in accordance with current theories of arcing and breakdown, will demonstrate the possibility of arc suppression. Finally, several additional test specimens will be included to study the basic nature of these interactions. The authors describe the rationale for the space flight experiment, the measurements to be made, the significance of the expected results, and the current design status of the flight hardware.

Wald, Lawrence W.↗
NASA NTRS1993

Interaction strength and model geometry effects on the structure of crossing-shock wave/turbulent boundary-layer interactions

The flowfield structure of a range of symmetric crossing-shock wave/turbulent boundary-layer interactions of varying strength is presented. The test geometry, consisting of a symmetric pair of opposing sharp fins at angle of attack, alpha, mounted to a flat plate, is studied experimentally for a range of alpha from 7 to 15 degrees at Mach numbers of 3 and 4. Results reveal that the basic flowfield shock structure remains similar in nature over the range of interaction strengths examined, with the only changes being in the scale and location of the various features present. The separated flow regions are classified as being either completely or partially separated, the completely separated case being the one in which the entire incoming boundary layer separates from the plate surface. For the current experiments, all but the weakest of the interactions exhibited complete boundary layer separation. Finally, the effects of model geometry are analyzed by comparing data for shock generators of varying lengths, with the results showing no evidence of upstream influence due to the shock generator trailing edges.

Garrison, T. J.↗
NASA NTRS1993

IRAS high resolution studies and modeling of closely interacting galaxies. Galaxy collisions: Infrared observations and analysis of numerical models. UV spectroscopy of massive young stellar populations in interacting galaxies

The Final Technical Report covering the period from 15 Aug. 1989 to 14 Aug. 1991 is presented. Areas of research included Infrared Astronomy Satellite (IRAS) high resolution studies and modeling of closely interacting galaxies; galaxy collisions: infrared observations and analysis of numerical models; and UV spectroscopy of massive young stellar populations in interacting galaxies. Both observational studies and theoretical modelling of interacting galaxies are covered. As a consequence the report is divided into two parts, one on each aspect of the overall project.

Lamb, Susan A.↗
DOE OSTI2019

Engineered barrier material interactions at elevated temperatures: Bentonite-metal interactions under elevated temperature conditions

The development of deep repository concepts in the USA is evaluating generic options for disposal of heat-generating nuclear spent nuclear fuel (SNF) waste for a suite of host rock media (clay rock, granite, salt). Large waste canister designs (e.g., dual purpose canisters or DPC’s) are currently being considered to accommodate many SNF assemblies. Large amounts of SNF in the waste packages will produce high thermal loads generating temperatures in excess of 200 °C for long periods of time. For a bentonite backfilled repository concept, prolonged exposure to high temperatures will induce chemical reactions in the engineered barrier system (EBS), particularly at barrier interfaces. Our focus is on experimental investigations and the application of thermodynamic modeling to evaluate clay-zeolite phase equilibria as a function of temperature and fluid chemistry. Experimental work on barrier material interactions under hydrothermal conditions (150 – 300 °C, 15-16 MPa) has elucidated mineral phase changes in Wyoming (Colony mine) bentonite in the presence of steel phases. Glassy material in bentonite is replaced by analcime-wairakite phases, and through apparent clinoptilolite recrystallization. The initial increase in dissolved silica leads to authigenic quartz formation. Such mineral assemblage suggests an initially silica-rich environment (analcime, clinoptilolite) moving towards Si-depleted conditions. Analcime-wairakite compositions suggest a well-defined solid-solution between these Na and Ca end-members. Smectite clay in these experiments is stable with Fe-saponite and chlorite growth co-existing with binary/ternary sulfides at steel interfaces. Little or no illite was observed in the reaction products which could be tied to silica oversaturation and low K in the system. The thermodynamic analysis is used to evaluate thermodynamic data and develop phase diagrams to describe stability field relations of secondary mineral phase occurrences. This analysis allows for delineation of potential reaction pathways in bentonite clay degradation and interactions with metallic phases. One example of this is the important role of dissolved silica plus other phase components to the formation of alteration mineralogy observed in these interactions. All these investigations are key to the assessment of thermally-induced degradation zones in the EBS during the thermal period and their effect on barrier performance in the safety assessment.

Jove-Colon, Carlos↗
DOE OSTI2011

Using Neutrino Nucleus Interactions as a Probe of the Strong Interaction

Neutrino scattering experiments have been studying QCD for over 30 years. From the Gargamelle experiments in the early 70's, through the subsequent bubble chamber and electronic detector experiments in the 80's and 90's, neutrino scattering experiments have steadily accumulated increasing statistics and minimized their systematic errors. An example of the more recent studies of QCD with neutrinos is from the TeVatron neutrino beam--the NuTeV {nu}-Fe experiment. The problem the community faces in trying to study QCD with modern neutrino data is that there is no experimentally verified way to scale neutrino-nucleus (for example, Fe) results to the equivalent neutrino-nucleon values making it difficult to combine neutrino nucleus scattering data with charged-lepton nucleus and nucleon scattering data in QCD global fits to extract parton distribution functions. This is particularly crucial since there is now indications that nuclear effects in neutrino nucleus interactions are different than those measured in charged-lepton nucleus scattering. To better understand this situation, the MINER{nu}A neutrino-nucleus scattering experiment at Fermilab, a collaboration of elementary-particle and nuclear physicists, is systematically studying neutrino nuclear effects off of He, C, Fe and Pb for a more thorough A-dependent study of nuclear PDFs and these correction factors.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2016

Metallography and fuel cladding chemical interaction in fast flux test facility irradiated metallic U-10Zr MFF-3 and MFF-5 fuel pins

Abstract The Mechanistic Fuel Failure (MFF) series of metal fuel irradiations conducted in the Fast Flux Test Facility (FFTF) provides an important potential comparison between data generated in the Experimental Breeder Reactor (EBR-II) and that expected in a larger-scale fast reactor. The irradiations were the beginning tests to qualify U-10wt%Zr as a driver fuel for FFTF. The FFTF core, with a 91.4 cm tall fuel column and a chopped cosine neutron flux profile, operated with a peak cladding temperature at the top of the fuel column, but developed peak burnup at the centerline of the core. This places the peak fuel temperature midway between the core center and the top of fuel, lower in the fuel column than in previous EBR-II experiments that had a 32-cm height core. The MFF-3 and MFF-5 qualification assemblies operated in FFTF to >10 at% burnup, and performed very well with no cladding breaches. The MFF-3 assembly operated to 13.8 at% burnup with a peak inner cladding temperature of 643°C, and the MFF-5 assembly operated to 10.1 at% burnup with a peak inner cladding temperature of 651°C. Because of the very high operating temperatures for both the fuel and the cladding, data from the MFF assemblies are most comparable to the data obtained from the EBR-II X447 experiment, which experienced two pin breaches. The X447 breaches were strongly influenced by a large amount of fuel/cladding chemical interaction (FCCI). The MFF pins benefitted from different axial locations of high burnup and peak cladding temperature, which helped to reduce interdiffusion between rare earth fission products and stainless steel cladding. Post-irradiation examination evidence illustrates this advantage. Comparing other performance data of the long MFF pins to prior EBR-II test data, the MFF fuel inside the cladding grew less axially, and the gas release data did not reveal a definitive difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

Periodic and chaotic oscillations in a tumor and immune system interaction model with three delays

In this paper, a tumor and immune system interaction model consisted of two differential equations with three time delays is considered in which the delays describe the proliferation of tumor cells, the process of effector cells growth stimulated by tumor cells, and the differentiation of immune effector cells, respectively. Conditions for the asymptotic stability of equilibria and existence of Hopf bifurcations are obtained by analyzing the roots of a second degree exponential polynomial characteristic equation with delay dependent coefficients. It is shown that the positive equilibrium is asymptotically stable if all three delays are less than their corresponding critical values and Hopf bifurcations occur if any one of these delays passes through its critical value. Numerical simulations are carried out to illustrate the rich dynamical behavior of the model with different delay values including the existence of regular and irregular long periodic oscillations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

The scaling of electron and positron generation in intense laser-solid interactions

This study presents experimental scalings of the electrons and positrons produced by intense laser-target interactions at relativistic laser intensities (10 18 –10 20 W cm -2 ). The data were acquired from three short-pulse laser facilities with laser energies ranging from 80 to 1500 J. We found a non-linear (≈E L 2 ) scaling of positron yield [Chen et al., Phys. Rev. Lett. 114, 215001 (2015)] and a linear scaling of electron yield with the laser energy. These scalings are explained by theoretical and numerical analyses. Positron acceleration by the target sheath field is confirmed by the positron energy spectrum, which has a pronounced peak at energies near the sheath potential, as determined by the observed maximum energies of accelerated protons. The parameters of laser-produced electron-positron jets are summarized together with the theoretical energy scaling. Finally, the measured energy-squared scaling of relativistic electron-positron jets indicates the possibility to create an astrophysically relevant experimental platform with such jets using multi-kilojoule high intensity lasers currently under construction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2016

Size consistent formulations of the perturb-then-diagonalize Møller-Plesset perturbation theory correction to non-orthogonal configuration interaction

In this paper we introduce two size consistent forms of the non-orthogonal configuration interaction with second-order Møller-Plesset perturbation theory method, NOCI-MP2. We show that the original NOCI-MP2 formulation [S. R. Yost, T. Kowalczyk, and T. VanVoorh, J. Chem. Phys. 193, 174104 (2013)], which is a perturb-then-diagonalize multi-reference method, is not size consistent. We also show that this causes significant errors in large systems like the linear acenes. By contrast, the size consistent versions of the method give satisfactory results for singlet and triplet excited states when compared to other multi-reference methods that include dynamic correlation. For NOCI-MP2 however, the number of required determinants to yield similar levels of accuracy is significantly smaller. These results show the promise of the NOCI-MP2 method, though work still needs to be done in creating a more consistent black-box approach to computing the determinants that comprise the many-electron NOCI basis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2011

Effect on cavity optomechanics of the interaction between a cavity field and a one-dimensional interacting bosonic gas

We investigate optomechanical coupling between one-dimensional interacting bosons and the electromagnetic field in a high-finesse optical cavity. We show that by tuning interatomic interactions, one can realize effective optomechanics with mechanical resonators ranging from side-mode excitations of a Bose-Einstein condensate (BEC) to particle-hole excitations of a Tonks-Girardeau (TG) gas. We propose that this unique feature can be formulated to detect the BEC-TG gas crossover and measure the sine-Gordon transition continuously and nondestructively.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Solar PV and BESS Plant-Level Voltage Control and Interactions: Experiments and Analysis

In real world operation, low-frequency oscillations associated with plant-level voltage control of inverter-based resources (IBRs) have been a concern of grid operators. Here, this research aims to demonstrate and analyze the effect of plant-level voltage control on system stability and potential interactions among IBRs. The experiment results of a 13.2-kV system interconnected with two IBRs—a 1-MW battery energy storage system (BESS) and a 430-kW solar photovoltaic (PV) plant—are presented. Both 0.5-Hz and 3-Hz oscillations become visible at certain conditions. The phenomenon is further explained by use of a feedback system consisting of the plant-level droop control and the effect of reactive power or var injection on voltage. The main components of the block diagram are obtained via frequency scan measurements. The analysis offers an understanding of the main contributors and other influencing factors of the 3-Hz and 0.5-Hz modes. It also reveals the role of the volt-var droop gain, the low-pass filter time constant, and the system impedance in stability.

14 SOLAR ENERGY↗
DOE OSTI2011

Extracting the photoproduction cross sections off the neutron, via the {gamma}n{yields}{pi}{sup -}p reaction, from deuteron data with final-state interaction effects

The incoherent pion photoproduction reaction {gamma}d {yields} {pi}{sup -}pp is considered theoretically in a wide energy region E{sub th}{<=}E{sub {gamma}}{<=}2700 MeV. The model applied contains the impulse approximation as well as the NN and {pi}N final-state-interaction (FSI) amplitudes. The aim of the paper is to study a reliable way for getting the information on elementary {gamma}n {yields} {pi}{sup -}p reaction cross sections beyond the impulse approximation for {gamma}d {yields} {pi}{sup -}pp. For the elementary {gamma}N {yields} {pi}N, N N {yields} N N, and {pi}N {yields} {pi}N amplitudes, the results of The George Washington University (GW) Data Analysis Center (DAC) are used. There are no additional theoretical constraints. The calculated cross sections d{sigma} /d{Omega}({gamma}d {yields} {pi}{sup -}pp) are compared with existing data. The procedure used to extract information on the differential cross section d{sigma} /d{Omega}({gamma}n {yields} {pi}{sup -}p) on the neutron from the deuteron data using the FSI correction factor R is discussed. The calculations for R versus {pi}{sup -}p center-of-mass (CM) angle {theta}{sub 1} of the outgoing pion are performed at different photon-beam energies with kinematic cuts for a ''quasifree'' process {gamma}n {yields} {pi}{sup -}p. The results show a sizable FSI effect R{ne}1 from the S-wave part of pp-FSI at small angles close to {theta}{sub 1}{approx}0: this region narrows as the photon energy increases. At larger angles, the effect is small (|R - 1|<<1) and agrees with estimations of FSI in the Glauber approach.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗