Search NASA⌕ Search

SEARCH · Search NASA

Results for “LUBRICATING OILS - VISCOSITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

X-ray photoelectron spectroscopic study of surface chemistry of dibenzyl-disulfide on steel under mild and severe wear conditions

Wear tests were performed on 304 stainless steel lubricated with pure mineral oil with and without dibenzyl-disulfide. Both mild and severe wear were observed. The type of wear was distinguished by a marked change in wear rate, friction coefficient, and wear scar appearance. The chemical composition of the wear scar surface was examined with X-ray photoelectron spectroscopy in conjunction with argon ion sputter etching. In severe wear scars, a sulfide was formed at the expense of the normal oxide layer. In mild wear scars, there were only superficial sulfur compounds, but there was a substantial increase in the oxide thickness.

Wheeler, D. R.↗
NASA NTRS1978

Large bearing operation without retainer

The design and testing of large high-speed ball bearings for space application is described. A well-defined lubrication system to provide oil to both race contacts in zero g allows stable operation without ball retainer.

Kingsbury, E.↗
NASA NTRS1957

Stress-life relation of the rolling-contact fatigue spin rig

The rolling-contact fatigue spin rig was used to test groups of SAE 52100 9.16-inch-diameter balls lubricated with a mineral oil at 600,000-, 675,000-, and 750,000-psi maximum Hertz stress. Cylinders of AISI M-1 vacuum and commercial melts and MV-1 (AISI M-50) were used as race specimens. Stress-life exponents produced agree closely with values accepted in industry. The type of failure obtained in the spin rig was similar to the subsurface fatigue spells found in bearings.

SURFACES, CONTACT - ROLLING↗
NASA NTRS2011

Active-Controlled Fluid Film Based on Wave-Bearing Technology

It has been known since 1967 that the steady-state and dynamic performance, including the stability of a wave bearing, are highly dependent on the wave amplitude. A wave-bearing profile can be readily obtained by elastically distorting the stationary bearing sleeve surface. The force that distorts the elastic sleeve surface could be an applied force or pressure. The magnitude and response of the distorting force would be defined by the relation between the bearing surface stiffness and the bearing pressure, or load, in a feedback loop controller. Using such devices as piezoelectric or other electromechanical elements, one could step control or fully control the bearing. The selection between these systems depends on the manner in which the distortion forces are applied, the running speed, and the reaction time of the feedback loop. With these techniques, both liquid- (oil-) or gas- (air-) lubricated wave bearings could be controlled. This report gives some examples of the dependency of the bearing's performance on the wave amplitude. The analysis also was proven experimentally.

Dimofte, Florin↗
NASA NTRS2017

Friction and Wear Modifiers Using Solvent Partitioning of Hydrophilic Surface-Interactive Chemicals Contained in Boundary Layer-Targeted Emulsions

A wear and/or friction reducing additive for a lubricating fluid in which the additive is a combination of a moderately hydrophilic single-phase compound and an anti-wear and/or anti-friction aqueous salt solution. The aqueous salt solution produces a coating on boundary layer surfaces. The lubricating fluid can be an emulsion-free hydrophobic oil, hydraulic fluid, antifreeze, water, or a water-based lubricant. Preferably, the moderately hydrophilic single-phase compound is sulfonated castor oil and the aqueous salt solution additionally contains boric acid and zinc oxide. The emulsions produced by the aqueous salt solutions, the moderately hydrophilic single-phase compounds, or the combination thereof provide targeted boundary layer organizers that significantly enhance the anti-wear and/or anti-friction properties of the base lubricant by decreasing wear and/or friction of sliding and/or rolling surfaces at boundary layers.

Richmond, Robert Chaffee↗
NASA NTRS1986

Heat- and Radiation-Resistant Lubricants for Metals

Protective and lubricating coatings formed in situ. Orthophthalonitrile reacts with metal-surface asperities at high frictional temperatures to form lubricating films of metal phthalocyanine. Compounds also formed with hot metal fragments torn from asperities. Bearing surfaces better protected from scoring, and fragments rendered less harmful to base fluids. Lubricants useful as additives to oils and greases in gears, transmissions, motors, and other machines where rubbing loads between metal parts may be severe. Because of their low volatility and lack of requirement for air or moisture, lubricants also useful in vacuums.

Lawton, E. A.↗
NASA NTRS1940

Experiments on Ball and Roller Bearings Under Conditions of High Speed and Small Oil Supply

This report describes a testing machine on which 35 millimeter bearings (bore) can be run at speeds of the order of 21,000 rpm, while the following factors are recorded: 1) oil circulation through bearing and oil temperature. 2) maximum temperature of outer bearing ring, 3) radial and axial load on bearing, 4) radial, axial, and angular clearance of bearing, 5) power consumption of bearing. The experiments show that the lubrication was most reliable and oil consumption lowest when the oil was introduced through a hole in the outer or inner ring of the bearing.

Getzlaff, Gunter↗
NASA NTRS2003

Industry Needs Fulfilled by Patented NASA PS300 Solid Lubricant Technology

In 1999, the NASA Glenn Research Center was awarded a patent (#5866518) for a new high-temperature solid lubricant coating material, PS300. A combination of wear-resistant metals and ceramics with solid lubricant additives, PS300 reduces friction and wear in sliding contacts from below ambient to over 650 C. This lubricant is an outgrowth of over three decades of high-temperature tribological research and was specifically developed as a shaft lubricant to protect foil air bearings used in Oil-Free turbomachinery, like gas turbines. Foil bearings are lubricated by air at high speeds but experience sliding and wear during initial startup and shut down when a lubricating film of air has not yet developed. PS300 shaft coatings have successfully lubricated foil bearings for over 100 000 cycles without wearing out.

DellaCorte, Christopher↗
NASA NTRS1977

Positive commandable oiler for satellite bearing lubrication

On-orbit commandable lubrication of ball bearings accomplished by direct oil application to the moving ball surfaces was studied. Test results for the lubricant applicator portion of the system are presented in conjunction with a design approach for the reservoir and metering components.

James, G. E.↗
NASA NTRS1982

Overview of liquid lubricants for advanced aircraft

An overall status report on liquid lubricants for use in high-performance turbojet engines is presented. Emphasis is placed on the oxidation and thermal stability requirements imposed upon the lubrication system. A brief history is iven of the development of turbine engine lubricants which led to synthetic oils with their inherent modification advantages. The status and state of development of some nine candidate classes of fluids for use in advanced turbine engines are discussed. Published examples of fundamental studies to obtain a better understanding of the chemistry involved in fluid degradation are reviewed. Also, alternatives to high temperature fluid development are described. The importance of of continuing work on improving high temperature lubricant candidates and encouraging development of fluid base stocks is discussed.

Loomis, W. R.↗
NASA NTRS2014

The MillSOT-A Spiral Orbit Tribometer on a Milling Machine

A spiral orbit tribometer (SOT) intended to characterize friction and wear phenomena has been constructed on a milling machine. The instrument, essentially a retainerless thrust bearing with one ball and flat races, is exceedingly simple and inexpensive to construct. The capabilities of the tribometer to measure both the coefficient of friction and contact electrical resistance are demonstrated with clean specimens as well as with well known lubricants such as molybdenum disulphide and Krytox oil. Operation in a purged environment of inert gas is also demonstrated. The results with these lubricants are quite close to what is obtained by other methods. Suggestions for extending the capabilities of the tribometer are given. This arrangement may find use in university mechanical engineering laboratories to introduce and study rolling contact motion as well as for research in contact mechanics and tribology.

Pepper, Stephen V.↗
DOE OSTI2023

Lubricant impacts on piston deposit formation in the Enterprise marine diesel research engine

The impact of lubricant formulation on piston deposits was studied using the Enterprise, a reduced-scale, single-cylinder, two-stroke crosshead marine diesel research engine. The Enterprise engine was specially designed for marine diesel lubricant research, with a custom reduced-scale cylinder lubricant injection system and extensive instrumentation of thermal boundary conditions on both the liner and piston. Lubricant conditions typical of full-scale marine diesel engines are obtained by matching mean piston speed, liner temperature profile, and combustion metrics to realistic values.Piston deposit thicknesses were measured after a set period of operation, with a focus on lubricant-based deposits on the lands and ring grooves, using both optical and contact-based measurement techniques. Engine operation for each lubricant was conducted according to a standardized protocol, with precise control of engine speed and load, cylinder lubricant injection rate, coolant temperatures, and system oil temperature; the liner and piston temperatures are continuously monitored during operation. After operation with each lubricant was completed, the engine was disassembled, and the piston and ring deposits were characterized. The piston was then thoroughly cleaned, and the lubricant system flushed, between each lubricant formulation being evaluated. The impacts on piston deposits of the lubricants being evaluated can thus be accurately quantified and are described herein.

Kaul, Brian↗
DOE OSTI2024

Minimizing Toxicity and Optimizing Lubricity of Ionic Liquids for Eco-Friendly Lubrication

As much as 60 million liters of lubricating fluids end up in the environment annually, and thus, the environmental impact of lubricants is increasingly recognized in addition to meeting the rheological and tribological requirements. Although US Environmental Protection Agency-approved environmentally acceptable base fluids are available, there is a lack of additives that are both nontoxic and effective in wear protection. Here, this study reports the successful development of a new class of ionic liquids (ILs) with demonstrated significantly lower aquatic toxicity and superior friction reduction and wear protection capabilities compared with a commercial lubricant additive and some ILs reported in the literature. Specifically, ammonium phosphate and phosphonium phosphate ILs with four-carbon alkyls have been identified with balanced oil solubility, thermal stability, toxicity, and lubricity, which provide fundamental insights for future development of eco-friendly ILs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗