Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift to Drag Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Mid-L/D Lifting Body Entry Demise Analysis

The mid-lift-to-drag ratio (mid-L/D) lifting body is a fully autonomous spacecraft under design at NASA for enabling a rapid return of scientific payloads from the International Space Station (ISS). For contingency planning and risk assessment for the Earth-return trajectory, an entry demise analysis was performed to examine three potential failure scenarios: (1) nominal entry interface conditions with loss of control, (2) controlled entry at maximum flight path angle, and (3) controlled entry at minimum flight path angle. The objectives of the analysis were to predict the spacecraft breakup sequence and timeline, determine debris survival, and calculate the debris dispersion footprint. Sensitivity analysis was also performed to determine the effect of the initial pitch rate on the spacecraft stability and breakup during the entry. This report describes the mid-L/D lifting body and presents the results of the entry demise and sensitivity analyses.

Ling, Lisa↗
DOE OSTI2022

Effect of the J-Shaped Wind Turbine Airfoil Opening Ratio and Thickness on the Performance of Symmetrical Airfoils

Abstract In this work, the effect of the inner opening ratio on the J-shaped airfoils aerodynamic performance was studied and documented for symmetrical airfoils. Three different airfoil thicknesses were investigated: small (NACA0008), medium (NACA0015), and large (NACA0024). For each airfoil thickness, effects of three inner opening ratios were analyzed: one-third, one-half, and two-thirds. The performance of each opening ratio was compared with the performance of the solid airfoil “zero opening ratio” for different angles of attack between 5 deg and 20 deg. All designs were simulated using the computational fluid dynamics (CFD) technology against experimental results for solid NACA4412 airfoil in the University of Wisconsin-Milwaukee (UWM) wind tunnel facility and other published experimental data. It was found that large eddy simulation yields accurate solutions with a smaller number of mesh cells compared to the k–ω turbulence model but with much longer computational time. The lift-to-drag ratio for all studied airfoils has a maximum value for solid airfoils compared to those equipped with openings. For airfoils equipped with 00.00% opening ratio “solid,” NACA0015 airfoil has the maximum lift-to-drag ratio. Furthermore, it was found that NACA0008 equipped with a 33.33% opening ratio has the best performance of all studied J-shaped airfoils.

Energy & Fuels↗
NASA NTRS1984

Meteorological accuracy requirements for aerobraking orbital transfer vehicles

Accuracy requirements for the prediction of atmospheric density for a transfer mission from geosynchronous orbit to low earth orbit using an aerobraking orbital transfer vehicle are presented. Uniform density variations such as would occur seasonally and diurnally were considered as well as density 'pockets' similar to what may have been observed on some of the Space Shuttle Orbiter entry flights. Variations in the lift-to-drag ratio from 0.3 to 1.5 were evaluated, with the values of the ratio of the vehicle weight to the product of the aerodynamic lift coefficient and the aerodynamic reference area ranging from 20 to 100 lb/sq ft. The results of the study indicated no problems for the range of lift-to-drag ratio values considered for uniform density variations of at least + or - 50 percent. However, density 'pockets' created problems if variations of + or - 30 percent from nominal occurred over altitude ranges of 1,000 to 10,000 ft.

Skalecki, L. M.↗
NASA NTRS1990

An aerodynamic tradeoff study of the scissor wing configuration

A scissor wing configuration, consisting of two independently sweeping wings was numerically studied. This configuration was also compared with an equivalent fixed wing baseline. Aerodynamic and stability and control characteristics of these geometries were investigated over a wide range of flight Mach numbers. It is demonstrated that in the purely subsonic flight regime, the scissor wing can achieve higher aerodynamic efficiency as the result of slightly higher aspect ratio. In the transonic regime, the lift to drag ratio of the scissor wing is shown to be higher than that of the baseline, for higer values of the lift coefficient. This tends to make the scissor wing more efficient during transonic cruise at high altitudes as well as during air combat at all altitudes. In supersonic flight, where the wings are maintained at maximum sweep angle, the scissor wing is shown to have a decided advantage in terms of reduced wave drag. From the view point of stability and control, the scissor wing is shown to have distinct advantages. It is shown that this geometry can maintain a constant static margin in supersonic as well as subsonic flight, by proper sweep scheduling. Furthermore, it is demonstrated that addition of wing mounted elevons can greatly enhance control authority in pitch and roll.

Selberg, Bruce P.↗
NASA NTRS1992

Aerodynamic characteristics of a hypersonic viscous optimized waverider at high altitudes

The present paper addresses the applicability of the basic concept of waveriding at high altitudes, and the extent to which the large viscous forces degrade the aerodynamic performance of waveriders. The waverider under consideration was designed using a continuum flow methodology. It is shown that the lift-to-drag ratio of high-altitude/high-Knudsen-number waveriders can be expected to be significantly lower than their low altitude/low Knudsen number counterparts. The aerodynamic performance of a representative waverider which was optimized for a 90-km, Mach-25 application is studied for altitudes ranging from 97 km to 145 km and incidence angles of 0 to 30 deg. Typical values of the lift-to-drag ratio were computed to be in the range of 0 to 0.3. Friction forces are mostly responsible for this poor performance. Friction forces account for more than 93 percent of the drag and significantly reduce lift.

Rault, Didier F. G.↗
NASA NTRS1992

Physiologically constrained aerocapture for manned Mars missions

Aerobraking has been proposed as a critical technology for manned missions to Mars. The variety of mission architectures currently under consideration presents aerobrake designers with an enormous range of potential entry scenarios. Two of the most important considerations in the design of an aerobrake are the required control authority (lift-to-drag ratio) and the aerothermal environment which the vehicle will encounter. Therefore, this study examined the entry corridor width and stagnation-point heating rate and load for the entire range of probable entry velocities, lift-to-drag ratios, and ballistic coefficients for capture at both Earth and Mars. To accomplish this, a peak deceleration limit for the aerocapture maneuvers had to be established. Previous studies had used a variety of load limits without adequate proof of their validity. Existing physiological and space flight data were examined, and it was concluded that a deceleration limit of 5 G was appropriate. When this load limit was applied, numerical studies showed that an aerobrake with an L/D of 0.3 could provide an entry corridor width of at least 1 degree for all Mars aerocaptures considered with entry velocities up to 9 km/s. If 10 km/s entries are required, an L/D of 0.4 to 0.5 would be necessary to maintain a corridor width of at least 1 degree. For Earth return aerocapture, a vehicle with an L/D of 0.4 to 0.5 was found to provide a corridor width of 0.7 degree or more for all entry velocities up to 14.5 km/s. Aerodynamic convective heating calculations were performed assuming a fully catalytic, 'cold' wall; radiative heating was calculated assuming that the shock layer was in thermochemical equilibrium. Heating rates were low enough for selected entries at Mars that a radiatively cooled thermal protection system might be feasible, although an ablative material would be required for most scenarios. Earth return heating rates were generally more severe than those encountered by the Apollo vehicles, and would require ablative heat shields in all cases.

Lyne, James Evans↗
NASA NTRS2007

Performance and Design Investigation of Heavy Lift Tiltrotor with Aerodynamic Interference Effects

The aerodynamic interference effects on tiltrotor performance in cruise are investigated using comprehensive calculations, to better understand the physics and to quantify the effects on the aircraft design. Performance calculations were conducted for 146,600-lb conventional and quad tiltrotors, which are to cruise at 300 knots at 4000 ft/95 deg F condition. A parametric study was conducted to understand the effects of design parameters on the performance of the aircraft. Aerodynamic interference improves the aircraft lift-to-drag ratio of the baseline conventional tiltrotor. However, interference degrades the aircraft performance of the baseline quad tiltrotor, due mostly to the unfavorable effects from the front wing to the rear wing. A reduction of rotor tip speed increased the aircraft lift-to-drag ratio the most among the design parameters investigated.

Yeo, Yyeonsoo↗
NASA NTRS1984

Complete flowfields over low and wide angle AOTV conceptual configurations

Flowfields over two conceptual aeroassisted orbital transfer vehicles, a moderate lift-to-drag ratio biconic, and an axisymmetric zero lift aerobrake are investigated. The solution procedures employ a compressible Navier-Stokes time-asymptotic technique for blunt body flow and a Parabolized Navier-Stokes spatial marching technique for the primarily supersonic shock layer flow over low-angle bodies. Emphasis is placed on the laminar convective heating predictions and comparisons to experimental data where available. Code robustness and solution times are discussed and guidelines are given for the specification of various numerical parameters. The Parabolized Navier-Stokes technique has a high probability of solution success for the range of applications considered herein, and very good comparisons with experimental heat-transfer data have been obtained. The blunt body Navier-Stokes code is more sensitive to parameter specification for the aerobrake calculations. Still, coarse grid solutions can be obtained quickly to get a good first cut at flowfield definition. Fair to good comparisons have been obtained between experimental heating and pressure data and coarse and fine grid solutions.

Gnoffo, P. A.↗
NASA NTRS1990

Experimental and predicted aerodynamic characteristics of a proposed Assured Crew Return Vehicle (ACRV) lifting-body configuration at Mach 6 and 10

The effects of Mach number, Reynolds number, and ratio of specific heats on the aerodynamic characteristics of a proposed Assured Crew Return Vehicle (ACRV) lifting-body configuration were examined for a range of angles of attack from -5 deg to 50 deg. Predictions made with a Langley-developed, three-dimensional Navier Stokes solver known as LAURA, which was exercised as an Euler solver for the present study, are compared with the experimental results. Unlike the Shuttle Orbiter, which experienced a significant nose-up increment in pitching moment with decreasing specific heat ratio (i.e., real gas effects), the aerodynamic characteristics of this lifting-body configuration are insensitive to changes in specific heat ratio. The maximum trimmed lift-to-drag ratio achieved was about 1.5. Predicted inviscid values of aerodynamic coefficients were generally in good agreement with measurement.

Micol, John R.↗
NASA NTRS1972

Studies of engine-airframe integrated hypersonic vehicles

A parametric study of an integrated airframe and engine is presented for a hypersonic transport at an altitude of 70,000 feet and a free stream Mach number of 6. The engine considered is a subsonic combustion ramjet using conventional hydrocarbon fuels. The lift-to-drag ratio of the aircraft for two configurations, one with full capture and accelerated flight and the other allowing spillage of the leading shock and in unaccelerated flight, is studied. The parameters varied are the engine efficiencies, the angle of attack, the combustion rates, as well as the captured mass flow. Lift-to-drag ratios on the order of 6.5 are obtained.

Saland, H.↗
NASA NTRS2005

An Investigation of Aerogravity Assist at Titan and Triton for Capture into Orbit About Saturn and Neptune

Previous work by our group has shown that an aerogravity assist maneuver at the moon Titan could be used to capture a spacecraft into a closed orbit about Saturn if a nominal atmospheric profile at Titan is assumed. The present study extends that work and examines the impact of atmospheric dispersions, variations in the final target orbit and low density aerodynamics on the aerocapture maneuver. Accounting for atmospheric dispersions substantially reduces the entry corridor width for a blunt configuration with a lift-to-drag ratio of 0.25. Moreover, the choice of the outbound hyperbolic excess speed (with respect to Titan) strongly influences the corridor width. Given the influence of these two parameters, certain mission scenarios may be feasible using a blunt aeroshell, while other mission designs would likely require a biconic vehicle with a higher lift-to-drag ratio. Preliminary simulations indicate that the same technique may be feasible for capture into orbit about Neptune using the tenuous atmosphere of Triton.

Ramsey, Philip↗
NASA NTRS1992

A hypersonic shock tunnel test of the Aeroassist Flight Experiment (AFE) vehicle at high altitude test conditions

The Aeroassist Flight Experiment (AFE) vehicle is a 4.26 m-diameter raked and blunted elliptic cone that is intended to obtain aerodynamic and aerothermodynamic data on blunt bodies at velocities near 10 km/s and altitudes above 75 km. Previous wind tunnel tests of this configuration have been at Mach numbers of 10 or lower. The present test program consisted of five test conditions at Mach numbers between 15 and 20 and simulated altitudes from 75 km to 97 km. Static longitudinal aerodynamic coefficients, the lift-to-drag ratio, and the trim angle-of-attack were obtained for angles-of-attack between 7 deg and 27 deg. The effects of angle-of-attack and shock Reynolds number, Re2, have been studied. These results indicate the AFE configuration is longitudinally stable. The variation of normal force slope, CNalpha and lift-to-drag slope, (L/D)alpha as well as the trim angle-of-attack with Re2 are documented. The trim angle-of-attack increases with decreasing values of shock Reynolds number (increasing altitude) while the lift-to-drag ratio at the trimmed conditions is relatively constant.

Wittliff, C. E.↗
NASA NTRS1974

An experimental and theoretical study of low-aspect ration swept and oblique wings at Mach numbers between 0.6 and 1.4

Experimental forces and moments for two wing-body combinations having (a) a swept wing and (b) an oblique wing are compared. At all Mach numbers, the oblique wing (at its optimum sweep angle) had higher maximum lift-to-drag ratios than the fixed, swept wing. At high angles of attack, the direction of the pitching or rolling tendencies of the oblique wing was a function of the spanwise distribution of wing bend or washout for the two bends being investigated. At low angles of attack, linear theory gave satisfactory predictions of the subsonic lift-curve slope, the aerodynamic-center travel with Mach number, and the maximum lift-to-drag ratio.

Hopkins, E. J.↗
NASA NTRS2002

Aerodynamic Assessment of Flight-Determined Subsonic Lift and Drag Characteristics of Seven Lifting-Body and Wing-Body Reentry Vehicle Configurations

This report examines subsonic flight-measured lift and drag characteristics of seven lifting-body and wing-body reentry vehicle configurations with truncated bases. The seven vehicles are the full-scale M2-F1, M2-F2, HL-10, X-24A, X-24B, and X-15 vehicles and the Space Shuttle Enterprise. Subsonic flight lift and drag data of the various vehicles are assembled under aerodynamic performance parameters and presented in several analytical and graphical formats. These formats are intended to unify the data and allow a greater understanding than individually studying the vehicles allows. Lift-curve slope data are studied with respect to aspect ratio and related to generic wind-tunnel model data and to theory for low-aspect-ratio platforms. The definition of reference area is critical for understanding and comparing the lift data. The drag components studied include minimum drag coefficient, lift-related drag, maximum lift-to drag ratio, and, where available, base pressure coefficients. The influence of forebody drag on afterbody and base drag at low lift is shown to be related to Hoerner's compilation for body, airfoil, nacelle, and canopy drag. This feature may result in a reduced need of surface smoothness for vehicles with a large ratio of base area to wetted area. These analyses are intended to provide a useful analytical framework with which to compare and evaluate new vehicle configurations of the same generic family.

Saltzman, Edwin J.↗
NASA NTRS1999

Flight-Determined Subsonic Lift and Drag Characteristics of Seven Lifting-Body and Wing-Body Reentry Vehicle Configurations With Truncated Bases

This paper examines flight-measured subsonic lift and drag characteristics of seven lifting-body and wing-body reentry vehicle configurations with truncated bases. The seven vehicles are the full-scale M2-F1, M2-F2, HL-10, X-24A, X-24B, and X-15 vehicles and the Space Shuttle prototype. Lift and drag data of the various vehicles are assembled under aerodynamic performance parameters and presented in several analytical and graphical formats. These formats unify the data and allow a greater understanding than studying the vehicles individually allows. Lift-curve slope data are studied with respect to aspect ratio and related to generic wind-tunnel model data and to theory for low-aspect-ratio planforms. The proper definition of reference area was critical for understanding and comparing the lift data. The drag components studied include minimum drag coefficient, lift-related drag, maximum lift-to-drag ratio, and, where available, base pressure coefficients. The effects of fineness ratio on forebody drag were also considered. The influence of forebody drag on afterbody (base) drag at low lift is shown to be related to Hoerner's compilation for body, airfoil, nacelle, and canopy drag. These analyses are intended to provide a useful analytical framework with which to compare and evaluate new vehicle configurations of the same generic family.

Saltzman, Edwin J.↗
NASA NTRS1983

An exploratory study of area-efficient vortex flap concepts

The potential of planform modification and hinge-line relocation to improve the thrust efficiency of vortex flaps was experimentally investigated on a 60-deg cropped delta wing model. Spanwise segmentation of the flap, together with chord-tailoring of the segments, allowed the vortex to be maintained on the outboard flap surfaces to higher angles of attack. In addition, location of the flap hinge aft of and underneath the wing leading edge generated substantial thrust from the vortex suction acting on the leading-edge lower surface. A combination of these beneficial effects allowed the flap/wing area to be reduced from 11.4 percent of the continuous flap to 6.3 percent of segmented flap, essentially without detriment to the incremental lift-to-drag ratio due to flap addition in the lift coefficient range 0.5-0.7 based on the basic wing area.

Rao, D. M.↗
NASA NTRS2019

Modern Aerocapture Guidance to Enable Reduced-Lift Vehicles at Neptune

Aerocapture is covered extensively in the literature as means of achieving orbital insertion with dramatic mass-saving results compared to fully-propulsive systems. One of the primary obstacles facing aerocapture is the inherent uncertainty associated with passing through a planet’s upper atmosphere. In-flight dispersions due to delivery errors, environment variables, and aerodynamic performance impose a large flight envelope. System studies for aerocapture often select high lift-to-drag ratios to compensate for these uncertainties. However, modern predictor-corrector guidance strategies have shown promise in recent years to provide robust control schemes in-situ. These algorithms do not rely on a pre-calculated reference trajectory and instead employ a numerical optimizer to continuously solve nonlinear equations of motion each guidance cycle. Numerical predictor-corrector strategies may provide considerable accuracy over heritage guidance schemes. The goal of this study is reproduce a landmark study of Neptune aerocapture and apply modern guidance to illustrate relative performance improvements and cost-saving potential. Capture constraints based on the theoretical corridor width are considered. Results indicate that heritage vehicles with moderate lift-to-drag ratios, lower than previous studies have indicated, may prove viable for aerocapture at Neptune.

Heidrich, C. R.↗