Search NASA⌕ Search

SEARCH · Search NASA

Results for “Linear accelerator structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

Reduction of Pertechnetate By Acetohydroxamic Acid: Formation of [tc**II(NO)(AHA)(2)(H(2)O)]**+ And Implications for the UREX Process

Reductive nitrosylation and complexation of ammonium pertechnetate by acetohydroxamic acid has been achieved in aqueous nitric and perchloric acid solutions. The kinetics of the reaction depend on the relative concentrations of the reaction components and are accelerated at higher temperatures. The reaction does not occur unless conditions are acidic. Analysis of the X-ray absorption fine structure spectroscopic data is consistent with a pseudo-octahedral geometry and the linear Tc-N-O bond typical of technetium nitrosyl compounds, and electron spin resonance spectroscopy is consistent with a d{sup 5} Tc(II) nitrosyl complex. The nitrosyl source is generally AHA, but it may be augmented by some products of the reaction with nitric acid. The resulting low-valency trans-aquonitrosyl(diacetohydroxamic)-technetium(II) complex ([Tc{sup II}(NO)(AHA){sub 2}H{sub 2}O]{sup +}, 1) is highly soluble in water, extremely hydrophilic, and is not extracted by tri-n-butylphosphate in a dodecane diluent. Its extraction properties are not pH-dependent: potentiometric-spectrophotometric titration studies indicate a single species from pH 4 down to -0.6 (calculated). This molecule is resistant to oxidation by H{sub 2}O{sub 2}, even at high pH, and can undergo substitution to form other technetium nitrosyl complexes. The potential formation of 1 during reprocessing may strongly impact the fate of technetium in the nuclear fuel cycle.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BiFeO(3): Synchrotron Radiation Structure Refinement And Magnetoelectric Geometry

Presently BiFeO{sub 3} focuses attention due to its multiferroic nature. This phase shows a highly distorted perovskite crystal structure, with R3c crystal symmetry. Details of the crystallographic structure are required input for a detailed explanation of its remarkable magnetoelectric properties. Present report contributes a high-resolution synchrotron radiation diffraction analysis of the BiFeO{sub 3} crystal structure. Single-phased sample was obtained by conventional solid-state reaction under bismuth atmosphere. XRD experiment was performed on beamline 2-1, Stanford Synchrotron Radiation Laboratory, with 12 keV X-rays. For data Rietveld processing, Fullprof software package was applied. Obtained cell parameters (in {angstrom}, hexagonal system description) were a = 5.57414(4); c = 13.85882(12). Group-theoretical analysis of BiFeO{sub 3} linear magnetoelectric tensor is presented. Only transverse effect is allowed by symmetry. Axial-symmetry polycrystal ceramics cannot show linear magnetoelectric coupling.

36 MATERIALS SCIENCE↗

GPU acceleration of all-electron electronic structure theory using localized numeric atom-centered basis functions

We present an implementation of all-electron density-functional theory for massively parallel GPU-based platforms, using localized atom-centered basis functions and real-space integration grids. Special attention is paid to domain decomposition of the problem on non-uniform grids, which enables compute- and memory-parallel execution across thousands of nodes for real-space operations, e.g. the update of the electron density, the integration of the real-space Hamiltonian matrix, and calculation of Pulay forces. To assess the performance of our GPU implementation, we performed benchmarks on three different architectures using a 103-material test set. We find that operations which rely on dense serial linear algebra show dramatic speedups from GPU acceleration: in particular, SCF iterations including force and stress calculations exhibit speedups ranging from 4.5 to 6.6. For the architectures and problem types investigated here, this translates to an expected overall speedup between 3–4 for the entire calculation (including non-GPU accelerated parts), for problems featuring several tens to hundreds of atoms. Additional calculations for a 375-atom Bi2Se3 bilayer show that the present GPU strategy scales for large-scale distributed-parallel simulations.

42 ENGINEERING↗

Quark-Hadron Duality in Neutron Spin-Structure and g{sub 2} moments at intermediate Q{sup 2}

Jefferson Lab experiment E01-012 measured the {sup 3}He spin-structure functions and virtual photon asymmetries in the resonance region in the momentum transfer range 1.0<Q{sup 2}<4.0 (GeV/c){sup 2}. Our data, when compared with existing deep inelastic scattering data, were used to test quark-hadron duality in g{sub 1} and A{sub 1} for {sup 3}He and the neutron. In addition, preliminary results on the {sup 3}He spin-structure function g{sub 2}, on the Burkhardt-Cottingham sum rule and on higher twist effects through the x{sup 2}-weighted moment d{sub 2} of the neutron were presented.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Accelerated Aging of PV Cables - The Development of Methods Towards Combined-Accelerated Stress Testing

PV cables allow the collection and distribution of electricity from modules to the energy grid. Durable cabling allows continuous operation of PV installations. Cables with a life less than that of the modules must be replaced - reducing electricity generation and adding to the system operating expense. We have examined the durability of a variety of representative cable samples using artificial UV weathering (IEC TS 62788-7-2) and combined accelerated stress testing (C-AST). Jackets in this study include PV-rated (polyolefin), building wire (PVC/PA), and multi-conductor (rubber, as in PV trackers), with some examples of black and red cables. Characterizations at read points include appearance (camera and optical microscope), surface roughness (linear profilometry), instrumented indentation, surface morphology (SEM), chemical composition (EDS), thermal decomposition (TGA), phase transition (DSC), crystalline structure (WAXS), and polymer chemical structure (FTIR). Complimentary examinations confirm damage to the external and interior layer(s) of less durable samples, including changes in morphology (e.g., cracking), chemistry (e.g., oxidation), structure, and mechanical performance (e.g., through-thickness modulus and hardness). The results may be generally compared to other examples from the field (PV installations) or after accelerated testing (IEC 61215). The methods in this study are presently being applied in a follow-on C-AST study, incorporating both dynamic and kinematic fixtures.

balance of systems↗

Parity-Violating PVDIS with SoLID

We are planning an experiment at JLab to measure parity-violation in deep inelastic scattering to high precision over a broad kinematic range. The goal of the experiment is to test the Standard Model, search for charge symmetry violation at the quark level, and to search for higher twist effects due to quark-quark interactions. We will also be able to measure the d/u ratio for the nucleon and search for nuclear effects in deep inelastic scattering.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Transverse spin physics at CLAS and CLAS12

We present ongoing and future measurement of spin-azimuthal asymmetries in semi-inclusive production of pions in deep inelastic scattering using the CLAS detector at the Thomas Jefferson National Accelerator Facility (JLab). The azimuthal modulations of the double and single spin asymmetries have been measured in a wide kinematic range, providing access to transverse momentum distributions of partons. An extensive experimental program has been proposed for the upgraded JLab, which will allow precision studies of the transverse structure of the nucleon.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Modeling and implementation of vertical excursion FFA in the Zgoubi ray-tracing code

Vertical Fixed Field Accelerators (vFFAs) feature complex and highly non-linear magnetic fields, which require simulation codes allowing step-wise particle tracking. Methods to model the 3D magnetic field of scaling vFFAs have been developed in the ray-tracing code Zgoubi. The field modeling and particle tracking methods include the field non-linearities, the fringe fields, and the field superposition of neighboring magnets. The procedure implements the vFFA analytical field expressions, allowing design studies and parameter optimizations using the Zgoubi built-in fit method. The vFFA procedure has been applied to a ten-fold symmetry ring with a triplet focusing structure designed to accelerate protons from 3 MeV to 12 MeV and studied under the ISIS-II proton driver prototype project. Results from particle tracking in externally generated 3D semi-analytical field maps and the developed vFFA analytical model are shown to be in excellent agreement.

43 PARTICLE ACCELERATORS↗

A digital twin solution for floating offshore wind turbines validated using a full-scale prototype

Abstract. In this work, we implement, verify, and validate a physics-based digital twin solution applied to a floating offshore wind turbine. The digital twin is validated using measurement data from the full-scale TetraSpar prototype. We focus on the estimation of the aerodynamic loads, wind speed, and section loads along the tower, with the aim of estimating the fatigue lifetime of the tower. Our digital twin solution integrates (1) a Kalman filter to estimate the structural states based on a linear model of the structure and measurements from the turbine, (2) an aerodynamic estimator, and (3) a physics-based virtual sensing procedure to obtain the loads along the tower. The digital twin relies on a set of measurements that are expected to be available on any existing wind turbine (power, pitch, rotor speed, and tower acceleration) and motion sensors that are likely to be standard measurements for a floating platform (inclinometers and GPS sensors). We explore two different pathways to obtain physics-based models: a suite of dedicated Python tools implemented as part of this work and the OpenFAST linearization feature. In our final version of the digital twin, we use components from both approaches. We perform different numerical experiments to verify the individual models of the digital twin. In this simulation realm, we obtain estimated damage equivalent loads of the tower fore–aft bending moment with an accuracy of approximately 5 % to 10 %. When comparing the digital twin estimations with the measurements from the TetraSpar prototype, the errors increased to 10 %–15 % on average. Overall, the accuracy of the results is promising and demonstrates the possibility of using digital twin solutions to estimate fatigue loads on floating offshore wind turbines. A natural continuation of this work would be to implement the monitoring and diagnostics aspect of the digital twin to inform operation and maintenance decisions. The digital twin solution is provided with examples as part of an open-source repository.

17 WIND ENERGY↗

Measurement and Analysis of Dose Rate Distribution in the Seismic Base-Isolation pit of the Electron Linac Oncology Facility - Paper 87

Recently electric linac oncology facilities incorporating seismic base-isolation structure have become very popular in Japan to prevent strong impact to the equipment by the earthquakes. When the boundary of the controlled area is set below the base-isolated foundations, additional shielding of iron plate is needed and the cost for shielding sometimes increases up to $1 M Since no one usually accesses underneath the treatment room, except short maintenance period for base-isolation structure, it is reasonable to set the boundary around the downstairs room (pit) by fence. However, it is very difficult to estimate the dose rate of new boundary by using the simple shielding calculation method, because of rotating gantry head and effect of scattering radiation in the base-isolation floor. In this study detail calculations by using Monte-Carlo calculation code MCNP5 have been performed to find out the practical shielding design. To be more specific, investigation for the complicated behavior of photons in the 'pit' have been performed by the analysis, i.e. (1) How much can we reduce the thickness of additional iron plate?, (2) Which angle of the beam direction will influence the most to the dose rate at the new boundary?, (3) Which component of the radiation is dominant at the new boundary? We also verified the calculated results by the measurement. We have performed the analysis of the behavior of photons in the pit and found out no additional iron shielding was necessary, which carried out an extreme reduction of costs. The main contribution to the dose rate at the boundary was scattered photons in the case of 0- degree beam direction. Good agreement between calculated and measured results were obtained, and passed the examination by the authority. It is concluded that the Monte-Carlo calculation code MCNP5 is very effective for the optimistic design of the electron linac oncology facilities incorporating seismic base-isolation structure. (authors)

43 PARTICLE ACCELERATORS↗

Cosmological aspects of a hyperbolic solution in f(R,T) gravity

This article deals with a cosmological scenario in f(R,T) gravity for a flat FLRW model of the universe. We consider the f(R,T) function as f(R)+f(T) which starts with a quadratic correction of the geometric term f(R) having structure f(R)=R+αR{sup 2}, and a linear matter term f(T)=2λT. To achieve the solution of the gravitational field equations in the f(R,T) formalism, we take the form of a geometrical parameter, i.e. scale factor a(t)=sinh{sup (1/n)}(βt) (Chawla et al., 2013), where β and n are model parameters. An eternal acceleration can be predicted by the model for 0<n<1, while the cosmic transition from the early decelerated phase to the present accelerated epoch can be anticipated for n≥1. The obtained model facilitates the formation of structure in the Universe according to the Jeans instability condition as our model transits from radiation dominated era to matter dominated era. We study the varying role of the equation of state parameter ω. We analyze our model by studying the behavior of the scalar field and discuss the energy conditions on our achieved solution. We examine the validity of our model via Jerk parameter, Om diagnostic, Velocity of sound and Statefinder diagnostic tools. We investigate the constraints on the model parameter n and H{sub 0} (Hubble constant) using some observational datasets: SNeIa dataset, H(z) (Hubble parameter) dataset, BAO (Baryon Acoustic Oscillation data) and their combinations as joint observational datasets H(z) + SNeIa and H(z) + SNeIa + BAO. It is testified that the present study is well consistent with these observations. We also perform some cosmological tests and a detailed discussion of the model.

79 ASTRONOMY AND ASTROPHYSICS↗

Laser and optical transport line for laser-based ion beam diagnostics and control in the SNS linear accelerator

We report our recent upgrade of the laser and optical transport line for the laser-based ion beam diagnostics (laser wire) system at the linear accelerator (linac) of the Spallation Neutron Source (SNS). A new light source based on diodepumped solid-state laser amplifiers has been developed to provide near diffraction-limited laser beam with a variety of pulse structures. The free-space optical transport line has been modified to include image relay optics with remote control, which greatly improved the laser beam quality and position stability at individual measurement stations. The upgraded system enables novel beam diagnostics/control capabilities including longitudinal profile measurement and high-energy proton beam extraction from the SNS linac.

Liu, Yun↗

Conceptual Design of the Drive Beam for a PWFA-LC

Plasma Wake-Field Acceleration (PWFA) has demonstrated acceleration gradients above 50 GeV/m. Simulations have shown drive/witness bunch configurations that yield small energy spreads in the accelerated witness bunch and high energy transfer efficiency from the drive bunch to the witness bunch, ranging from 30% for a Gaussian drive bunch to 95% for bunch with triangular shaped longitudinal profile. These results open the opportunity for a linear collider that could be compact, efficient and more cost effective than the present microwave technologies. A concept of a PWFA-based Linear Collider (PWFA-LC) has been developed by the PWFA collaboration. Here we will describe the conceptual design and optimization of the drive beam, which includes the drive beam linac and distribution system. We apply experience of the CLIC drive beam design and demonstration in the CLIC Test Facility (CTF3) to this study. We discuss parameter optimization of the drive beam linac structure and evaluate the drive linac efficiency in terms of the drive beam distribution scheme and the klystron/modulator requirements.

43 PARTICLE ACCELERATORS↗

Measurement Of Gas Electron Multiplier (GEM) Detector Characteristics

The High Energy Physics group of the University of Texas at Arlington has been developing gas electron multiplier detectors to use them as sensitive gap detectors in digital hadron calorimeters for the International Linear Collider, a future high energy particle accelerator. For this purpose, we constructed numerous GEM detectors that employ double GEM layers. In this study, two kinds of prototype GEM detectors were tested; one with 28x28 cm{sup 2} active area double GEM structure with a 3 mm drift gap, a 1 mm transfer gap and a 1 mm induction gap and the other with two 3x3 cm{sup 2} GEM foils in the amplifier stage with a 5 mm drift gap, a 2 mm transfer gap and a 1 mm induction gap. The detectors' characteristics from exposure to high-energy charged particles and other radiations were measured using cosmic rays and {sup 55}Fe radioactive source. From the {sup 55}Fe tests, we observed two well separated characteristic X-ray emission peaks and confirmed the detectors' functionality. We also measured chamber gains to be over 6000 at a high voltage of 395 V across each GEM electrode. The responses to cosmic rays show the spectra that fit well to Landau distributions as expected from minimum ionizing particles.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Production of BaBar Skimmed Analysis Datasets Using the Grid

The BABAR Collaboration, based at Stanford Linear Accelerator Center (SLAC), Stanford, US, has been performing physics reconstruction, simulation studies and data analysis for 8 years using a number of compute farms around the world. Recent developments in Grid technologies could provide a way to manage the distributed resources in a single coherent structure. We describe enhancements to the BABAR experiment's distributed skimmed dataset production system to make use of European Grid resources and present the results with regard to BABAR's latest cycle of skimmed dataset production. We compare the benefits of a local and Grid-based systems, the ease with which the system is managed and the challenges of integrating the Grid with legacy software. We compare job success rates and manageability issues between Grid and non-Grid production.

43 PARTICLE ACCELERATORS↗

Probing Quark-Gluon Interactions with Transverse Polarized Scattering

Transverse polarized inelastic scattering extends the power of the electromagnetic interaction as a probe of nucleon dynamics beyond the leading order regime explored with longitudinally polarized DIS. In transverse polarized scattering, the twist-3 g{sub 2} spin structure function contributes at the same order as the longitudinal, twist-2, g{sub 1}, so interactions between quarks and gluons can be studied, opening a window on the mechanisms of confinement. This talk reports the results of Jefferson Lab's Resonances Spin Structure experiment measurement of g{sub 2} and the d{sub 2} twist-3 quark matrix element at a four-momentum transfer of 1.3 GeV{sup 2}.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

GPU acceleration of hybrid functional calculations in the SPARC electronic structure code

We present a Graphics Processing Unit (GPU)-accelerated version of the real-space SPARC electronic structure code for performing hybrid functional calculations in generalized Kohn–Sham density functional theory. In particular, we develop a batch variant of the recently formulated Kronecker product-based linear solver for the simultaneous solution of multiple linear systems. We then develop a modular, math kernel based implementation for hybrid functionals on NVIDIA architectures, where computationally intensive operations are offloaded to the GPUs, while the remaining workload is handled by the central processing units (CPUs). Considering bulk and slab examples, we demonstrate that GPUs enable up to 8× speedup in node-hours and 80× in core-hours compared to CPU-only execution, reducing the time to solution on V100 GPUs to around 300 s for a metallic system with over 6000 electrons, and significantly reducing the computational resources required for a given wall time.

Kohn-Sham density functional theory↗

Parallel interior-point solver for block-structured nonlinear programs on SIMD/GPU architectures

Here, we investigate how to port the standard interior-point method to new exascale architectures for block-structured nonlinear programs with state equations. Computationally, we decompose the interior-point algorithm into two successive operations: the evaluation of the derivatives and the solution of the associated Karush-Kuhn-Tucker (KKT) linear system. Our method accelerates both operations using two levels of parallelism. First, we distribute the computations on multiple processes using coarse parallelism. Second, each process uses SIMD/GPU accelerators locally to accelerate the operations using fine-grained parallelism. The KKT system is reduced by eliminating the inequalities and the state variables from the corresponding equations. We demonstrate our method's capability on the supercomputer Polaris, a testbed for the future exascale Aurora system. Each node is equipped with four GPUs, a setup amenable to our two-level approach. Our experiments on the stochastic optimal power flow problem show that the reduction method is 50x faster than the sparse linear solver HSL MA57 running in serial on the CPU, and 6x faster than Pardiso running in parallel on CPU on the same number of processes.

97 MATHEMATICS AND COMPUTING↗