Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low velocity impact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The effects of impact velocity on the evolution of experimental regoliths

Fragmental targets consisting of a coarse-grained gabbro were subjected to multiple impacts with stainless-steel spheres at 0.7, 1.4, and 1.9 km/s in order to investigate the effects of impact velocity on the generation and evolution of experimental regoliths. Although the low-velocity impactors were shown to be more efficient in terms of both mass comminution and the creating of new surfaces, the comminuted material formed by the faster projectiles possessed smaller mean grain sizes and larger proportions of fine-grained debris. The 2-4 mm material was found in all cases to exhibit a mass excess relative to the adjacent size fractions.

Cintala, Mark J.↗
DOE OSTI2024

Extensive Secondary Cratering From the InSight Sol 1034a Impact Event

Abstract Impact cratering is one of the fundamental processes throughout the history of the Solar System. The formation of new impact craters on planetary bodies has been observed with repeat images from orbiting satellites. However, the time gap between images is often large enough to preclude detailed analysis of smaller‐scale features such as secondary impact craters, which are often removed or buried over a short time period. Here we use a seismic event detected on Mars by the NASA InSight mission to investigate secondary cratering at a new impact crater. We strengthen the case that the seismic event that occurred on Sol 1034 (S1034a) is the result of a new impact cratering event. Using the exact timing of this event from InSight, we investigated the resulting new impact crater in orbital image data. The S1034a impact crater is approximately 9 m in diameter but is responsible for over 900 secondary impact events in the form of low albedo spots that are located at distances of up to almost 7 km from the primary crater. We suggest that the low albedo spots formed from relatively low energy ejecta, with individual ejecta block velocities less than 200 m s −1 . We estimate that the low albedo spots, the main evidence of secondary impact processes at this new impact event, fade within 200–300 days after formation.

Grindrod, P. M. [Natural History Museum London UK]↗
NASA NTRS2007

Stardust in STARDUST - the C, N, and O Isotopic Compositions of Wild 2 Cometary Matter in Al Foil Impacts

In January 2006, the Stardust mission successfully returned dust samples from the tail of comet 81P/Wild 2 in two principal collection media, low density silica aerogel and Al foil. While hypervelocity impacts at the Stardust encounter velocity of 6.1 kilometers per second into Al foils are generally highly disruptive for natural, silicate-dominated impactors, previous studies have shown that many craters retain sufficient residue to allow a determination of the elemental and isotopic compositions of the original projectile. We have used two NanoSIMS ion microprobes to perform C, N, and O isotope imaging measurements on four large (59-295 micrometer diameter) and on 47 small (0.32-1.9 micrometer diameter) Al foil impact craters as part of the Stardust Preliminary Examination. Most analyzed residues in and around these craters are isotopically normal (solar) in their C, N, and O isotopic compositions. However, the debris in one large crater shows an average N-15 enrichment of approx. 450%o, which is similar to the bulk composition of some isotopically primitive interplanetary dust particles and to components of some primitive meteorites. A 250 nm grain in another large crater has an O-17 enrichment with approx. 2.65 times the solar O-17/O-16 ratio. Such an O isotopic composition is typical for circumstellar oxide or silicate grains from red giant or asymptotic giant branch stars. The discovery of this circumstellar grain clearly establishes that there is authentic stardust in the cometary samples returned by the Stardust mission. However, the low apparent abundance of circumstellar grains in Wild 2 samples and the preponderance of isotopically normal material indicates that the cometary matter is a diverse assemblage of presolar and solar system materials.

Stadermann, Frank J.↗
NASA NTRS1994

Dynamics of volatile delivery from outer to inner solar system

Owen et al. propose that the Ar excess of Venus compared to Earth was caused by impact of a large icy planetesimal from the outer solar system, where temperatures were low enough for Ar to adhere to ice, about 30 K. A body of solar Ar/Si and C/H similar to Pluto and Triton less than 100 km diameter would suffice. However, direct delivery from the Uranus-Neptune zone to Venus would result in a very high approach velocity, causing erosion rather than accretion of volatiles. It would also be an extremely improbable event. Virtually all icy bodies scattered from the Uranus-Neptune zone to the terrestrial zone were strongly perturbed by Jupiter, but even then arrived at Venus (or Earth) at too-high velocities. What is needed is a 'deboost' of bodies scattered inward from Jupiter by Earth and Venus perturbations, prior to impact into Venus. This has low probability, since the influence radii of Venus and Earth for the high velocities are small compared to that of Jupiter for the lower velocities further out. It is desirable that this problem be examined by an integerator that allows for close approaches, such as developed by Levison and Duncan. However, it would be a long and expensive computation compared to explaining short-period comets to accomplish the third 'deboost' phase. But since close encounters dominate in such distant scattering, an Opik algorithm seems the appropriate reconnaissance tool.

Kaula, W. M.↗
NASA NTRS1997

The Galim LL/EH Polymict Breccia: Evidence for Impact-Induced Exchange Between Reduced and Oxidized Meteoritic Material

Galim is a polymict breccia consisting of a heavily shocked (shock stage S6) LL6 chondrite, Galim (a), and an impact-melted EH chondrite, Galim (b). Relict chondrules in Galim (b) served as nucleation sites for euhedral enstatite grains crystallizing from the impact melt. Many of the reduced phases typical of EH chondrites (e.g., Si-bearing metallic Fe-Ni; Ti-bearing troilite) are absent. Galim (b) was probably shock-melted while in contact with a more oxidized source, namely, Galim (a); during this event, Si was oxidized from the metal and Ti was oxidized from troilite. Galim (a) contains shock veins and recrystallized, unzoned olivine. The absence of evidence for reduction in Galim (a) may indicate that the amount of LL material greatly exceeded that of EH material; shock metamorphism may have taken place on the LL parent body. Shock-induced redox reactions such as those inferred for the Galim breccia appear to be restricted mainly to asteroids because the low-end tail of their relative-velocity distribution permits mixing of intact disparate materials (including accretion of projectiles of different oxidation states), whereas the peak of the distribution leads to high equilibration shock pressures (allowing impact-induced exchange between previously accreted, disequilibrated materials). Galim probably formed by a two-stage process: (I) accretion to the LL parent body of an intact EH projectile at low relative velocities, and (2) shock metamorphism of the assemblage by the subsequent impact of another projectile at significantly higher relative velocities.

Rubin, Alan E.↗
NASA NTRS1985

Impact processes and their implications for planetary formation and early evolution

Small impact craters dominate the geomorphology of small planetary bodies. Even Mars has extensive impact-dominated landscapes. The regoliths of the Moon and asteroids are created and maintained by impacts. It is now widely recognized that large impacts (craters 100-1000 km in diameter) are one of the major tectonic elements in the lithospheres of bodies like the Moon, Mercury, Mars and Callisto. The multiring basins these large impacts produce sometimes extend over an entire hemisphere. Such basins may have also affected tectonics during the Earth's hadean era. Although it has long been appreciated that low velocity collisions played a major role in the accretion of planetesimals into planets, recent work indicates a far more profound role for impacts. Studies of the interaction of planetary atmospheres with large impacts, begun in an effort to define the climatological effects of the K-T impactor, suggest that impacts may remove a significant fraction of a planet's atmosphere. Such removal now offers hope of explaining the puzzling systematics of the heavy noble gases in the atmospheres of the Earth, Venus, and Mars.

Melosh, H. J.↗
NASA NTRS2016

Cassini Ring Plane Crossings: Hypervelocity Impact Risks to Sun Sensor Assemblies

For both F/G and D-ring crossings: Probability of a penetration damage of the SSH (Sun Sensor Head) window glass is very low; Optical attenuation due to craters on the surface of the window glass caused by direct HVI (Hyper-Velocity Impact) by dust particle is estimated to be less than 1 percent; Optical attenuation due to secondary debris cloud generated by the disintegrated ring dust particles is estimated to be less than 1 percent. To better manage the Sun sensor damage risk during selected proximal orbit crossings, it is highly desirable to follow the contingency procedures mentioned in Section VII of the paper: Details of this contingency procedure are given in the paper entitled "Cassini Operational Sun Sensor Risk Management During Proximal Orbit Saturn Ring Plane Crossings" authored by David M. Bates. Based on results of risk analyses documented in this work and contingency planning work described in the paper mentioned above, we judge that the proximal orbit campaign will be safe from the viewpoint of dust HVI hazard.

dust particles↗
NASA NTRS2006

Forces Generated by High Velocity Impact of Ice on a Rigid Structure

Tests were conducted to measure the impact forces generated by cylindrical ice projectiles striking a relatively rigid target. Two types of ice projectiles were used, solid clear ice and lower density fabricated ice. Three forms of solid clear ice were tested: single crystal, poly-crystal, and "rejected" poly-crystal (poly-crystal ice in which defects were detected during inspection.) The solid ice had a density of approximately 56 lb/cu ft (0.9 gm/cu cm). A second set of test specimens, termed "low density ice" was manufactured by molding shaved ice into a cylindrical die to produce ice with a density of approximately 40 lb/cu ft (0.65 gm/cu cm). Both the static mechanical characteristics and the crystalline structure of the ice were found to have little effect on the observed transient response. The impact forces generated by low density ice projectiles, which had very low mechanical strength, were comparable to those of full density solid ice. This supports the hypothesis that at a velocity significantly greater than that required to produce fracture in the ice, the mechanical properties become relatively insignificant, and the impact forces are governed by the shape and mass of the projectile.

Pereira, J. Michael↗
NASA NTRS1991

The formation of terrains antipodal to major impacts

The SALE, or Simplified Arbitrary Lagrangian Eulerian code is presently used to calculate the antipodal pressures generated by large impacts on icy satellites and planets of various compositions and core sizes. While in a high density core/lower density mantle planet there is a refraction of the incident pressure wave away from the antipode by the core, resulting in a low antipodal pressure, a planet with a low velocity core with a higher-wave speed mantle will focus the waveform to maximize antipodal pressure. Specific impact basins on the moon, Mercury, and several icy satellites are modeled to ascertain whether the impacts were capable of producing the observed antipodal features.

Watts, Alison W.↗
NASA NTRS1999

Behavior of Windblown Sand on Mars: Results from Single-Particle Experiments

Experiments are investigating the behavior of individual sand grains in the high-energy martian aeolian regime. Energy partitioning during impact of a saltating grain determines grain longevity, but it also influences the way in which the bed becomes mobilized by reptation. When single grains of sand are fired into loose beds, the bed can absorb up to 90% of the impact energy by momentum transfer to other grains; it has been discovered that the impacting grains cause circular craters even at low impact angles. Hundreds of grains can be splashed by a single high-velocity (100 m/s) impact causing more bed disturbance through reptation than previously thought. The research is supported by NASA's PG&G Program. Because the martian aeolian environment in both high energy and of long duration, the most mobile fractions of windblown sand should have eradicated themselves by attrition, unless sand supply has kept pace with destruction. It is therefore important to understand the rate of grain attrition in order to make sense of the existence of vast dune fields on Mars. Attrition, has been addressed in other studies, but precise data for a single saltating grain striking a loose bed of sand have not been acquired -- the quintessential case to be understood for dunes on Mars. To acquire these data, we are employing a compound crossbow which has the bolt-firing mechanism replaced with a pneumatically-automated sabot system. The sabot can launch individual grains of sand of any size between several millimeters and about 50 microns, at velocities up to 100m/s. This is around the maximum velocity expected for saltating grains on Mars. The sabot sled is equipped with photoelectric sensors for measuring shot velocity. Baffling of the grain's exit orifice has enabled projection of single grains without significant aerodynamic effects from the sabot. Grains are fired into loose beds of sand at about 15 degrees from the horizontal (typical saltation trajectory at impact) while being filmed on high-speed video. High-intensity pulse illumination for the grains is triggered by the solenoid-operated bow trigger. A 45 degree mirror over the impact site provides simultaneous horizontal and vertical images of the impact on each video frame. UV fluorescence is enabling grain and grain-fragment recovery. At 100 m/s, grains of all sizes shatter into many fragments when the sand is replaced with a solid target. Kinetic energy of the grains at this velocity exceeds the critical energy for catastrophic failure of minerals. Although probably exceptional as a grain speed, it suggests that conditions on Mars might elevate materials into an attrition regime not encountered on other planets; individual grains blown across rock pavements on Mars will have short lifespans. When experimental grains impact loose (dune) sand, much, if not most of the kinetic energy is converted into momentum of other grains. Using high-speed filming, the energy involved in splashing grains at the impact site can be derived from the size of the crater, the speed of the splashed grains, and the rebound speed of the impactor. The amount of energy partitioned into material failure (as opposed to momentum) is too small a fraction of the total to be calculated under these circumstances. This does not necessarily mean that little damage occurs to the grains (the full extent of the damage has yet to be determined) because only a small fraction of the impact energy is required for inducing brittle fracture. Damage is orders of magnitude less than during impact against solid surfaces.

Marshall, J. R.↗
NASA NTRS2006

Laboratory Simulation of Impacts upon Aluminum Foils of the Stardust Spacecraft: Calibration of Dust Particle Size from Comet Wild 2

Metallic aluminium alloy foils exposed on the forward, comet-facing surface of the aerogel tray on the Stardust spacecraft are likely to have been impacted by the same cometary particle population as the dedicated impact sensors and the aerogel collector. The ability of soft aluminium alloy to record hypervelocity impacts as bowl-shaped craters offers an opportunistic substrate for recognition of impacts by particles of a wide potential size range. In contrast to impact surveys conducted on samples from low Earth orbit, the simple encounter geometry for Stardust and Wild 2, with a known and constant spacecraft-particle relative velocity and effective surface-perpendicular impact trajectories, permits closely comparable simulation in laboratory experiments. For a detailed calibration programme we have selected a suite of spherical glass projectiles of uniform density and hardness characteristics, with well-documented particle size range from 10 microns to nearly 100 microns. Light gas gun buckshot firings of these particles at approximately 6km s)exp -1) onto samples of the same foil as employed on Stardust have yielded large numbers of craters. Scanning electron microscopy of both projectiles and impact features has allowed construction of a calibration plot, showing a linear relationship between impacting particle size and impact crater diameter. The close match between our experimental conditions and the Stardust mission encounter parameters should provide another opportunity to measure particle size distributions and fluxes close to the nucleus of Wild 2, independent of the active impact detector instruments aboard the Stardust spacecraft.

Kearsley, A. T.↗
NASA NTRS2007

Stardust in STARDUST - the C, N, and O Isotopic Compositions of Wild 2 Cometary Matter in Al foil Impacts

In January 2006, the STARDUST mission successfully returned dust samples from the tail of comet 81P/Wild 2 in two principal collection media, low density silica aerogel and Al foil. While hypervelocity impacts at 6.1 km/s, the encounter velocity of STARDUST, into Al foils are generally highly disruptive for natural, silicate-dominated impactors, previous studies have shown that many craters retain sufficient residue to allow a determination of the elemental and isotopic compositions of the original projectile. We have used the NanoSIMS to perform C, N, and O isotope imaging measurements on four large (59-370 microns diameter) and on 47 small (0.32-1.9 microns diameter) Al foil impact craters as part of the STARDUST Preliminary Examination. Most analyzed residues in and around these craters are isotopically normal (solar) in their C, N, and O isotopic compositions. However, the debris in one large crater shows an average 15N enrichment of approx. 450 %, which is similar to the bulk composition of some isotopically primitive interplanetary dust particles. A 250 nm grain in another large crater has an O-17 enrichment with approx. 2.65 times the solar O-17/O-16 ratio. Such an O isotopic composition is typical for circumstellar oxide or silicate grains from red giant or asymptotic giant branch stars. The discovery of this circumstellar grain clearly establishes that there is authentic stardust in the cometary samples returned by the STARDUST mission. However, the low apparent abundance of circumstellar grains in Wild 2 samples and the preponderance of isotopically normal material indicates that the cometary matter is a diverse assemblage of presolar and solar system materials.

Stadermann, Frank J.↗
NASA NTRS1994

Physics of interplanetary dust capture via impact into organic polymer foams

The physics of hypervelocity impacts into foams is of interest because of the possible application to interplanetary dust particle (IDP) capture by spacecraft. We present a model for the phenomena occurring in such impacts into low-density organic polymer foams. Particles smaller than foam cells behave as if the foam is a series of solid slabs and are fragmented and, at higher velocities, thermally altered. Particles much larger than the foam cells behave as if the foam were a continuum, allowing the use of a continuum mechanics model to describe the effects of drag and ablation. Fragmentation is expected to be a major process, especially for aggregates of small grains. Calculations based on these arguments accurately predict experimental data and, for hypothetical IDPs, indicate that recovery of organic materials will be low for encounter velocities greater than 5 km/s. For an organic particle 100 micrometers in diameter, approx. 35% of the original mass would be collected in an impact at 5 km/s, dropping to approx. 10% at 10 km/s and approx. 0% at 15 km/s. For the same velocities the recovery ratios for troilite (FeS) are approx. 95%, 65%, and 50%, and for olivine (Mg2SiO4) they are approx. 98%, 80%, and 65%, demonstrating that inorganic materials are much more easily collected. The density of the collector material has only a second-order effect, changing the recovered mass by less than 10% of the original mass.

Anderson, William W.↗
NASA NTRS1987

Centrifuge impact cratering experiments: Scaling laws for non-porous targets

A geotechnical centrifuge was used to investigate large body impacts onto planetary surfaces. At elevated gravity, it is possible to match various dimensionless similarity parameters which were shown to govern large scale impacts. Observations of crater growth and target flow fields have provided detailed and critical tests of a complete and unified scaling theory for impact cratering. Scaling estimates were determined for nonporous targets. Scaling estimates for large scale cratering in rock proposed previously by others have assumed that the crater radius is proportional to powers of the impactor energy and gravity, with no additional dependence on impact velocity. The size scaling laws determined from ongoing centrifuge experiments differ from earlier ones in three respects. First, a distinct dependence of impact velocity is recognized, even for constant impactor energy. Second, the present energy exponent for low porosity targets, like competent rock, is lower than earlier estimates. Third, the gravity exponent is recognized here as being related to both the energy and the velocity exponents.

Schmidt, Robert M.↗
NASA NTRS1996

Advanced liquid Oxygen (LO2) propellant conditioning concept testing

Extensive testing was performed on the promising L02 propellant conditioning concept of passive recirculation (no-bleed). Data from the project is being used to further anchor models in L02 conditioning behavior and broaden the data base of no-bleed and low-bleed conditioning. Data base expansion includes results from testing the limits of no-bleed and low-bleed conditioning with various configuration changes to the test facility and designed test article. Configuration changes include low velocity effects in the recirculation loop above the test article, test article internal constriction impacts, test article out-of-plane effects, impact from an actual Titan L02 pump attachment, feed duct slope effects, and up-leg booster effects. LN2 was used as the test fluid. The testing was conducted between July 1994 and January 1995 at the west test area of Marshall Space Flight Center. Data have shown that in most cases passive recirculation was demonstrated when the aforementioned limits were applied.

Hasting, J. H.↗
DOE OSTI2026

Integration of the Biot–Gassmann Fluid Substitution Method and Machine Learning-Based Velocity–Stress Relationship for Estimating In Situ Stresses

Recent advancements have shown that in situ stresses can be reliably estimated through an integrated machine/deep learning (ML/DL)-based framework, which relies on models trained and validated using true triaxial ultrasonic velocity (TUV) experimental data that involve measurements of ultrasonic velocity in saturated rocks under varying stress configurations. However, when the goal is to interpret lower frequency measurements, it may be more appropriate to run experiments on dry rocks and then obtain Biot–Gassmann-derived equivalent saturated velocities (low-frequency approximation) and employ these quantities for training ML/DL models to predict in situ stress. Whether the dispersion effect of frequency on the velocity–stress relationship substantially impacts in situ stress prediction is an important and unresolved question. This work presents an enhancement of ML/DL-based workflow by training and implementing ML/DL models using equivalent saturated acoustic velocities (low-frequency) obtained by applying Biot–Gassmann fluid substitution on the ultrasonic velocities of dry cores. The models were trained on TUV data sets derived from three subsurface cores extracted from the geothermal well 16B(78)-32 at the Utah FORGE site. Each core was subjected to 75 unique stress configurations for velocity measurement in the dry state. The ML/DL trained on the TUV data set with equivalent saturated velocities demonstrated promising performance to predict in situ stress in subsurface geological rocks using velocity–stress relationships with R 2 of 0.86, 0.971, and 0.975 and root mean squared error (RMSE) of 2.59, 1.92, and 1.80 for validation/testing phases of vertical, minimum horizontal, and maximum horizontal stress models, respectively. Additionally, interpretation and explanation by Shapley additive explanations (SHAP) analysis further improved scientific validation and model reliability for estimating in situ stresses.

colloids↗
NASA NTRS1987

Impact experiments in low-temperature ice

Cubic and cylindrical water ice targets at 257 and 81 K have been subjected to impact velocities between 0.1 and 0.64 km/sec and impact energies of 10 to the 9th-10 to the 10th ergs, yielding craters that are 2-3 times larger than those obtained through equal energy impacts in basaltic targets. On the basis of a similarity analysis, general scaling laws are derived for strength-controlled crater formation and applied in a consideration of crater formation on the icy Galilean and Saturnian satellites. Surface ages are predicted by the analysis to appear greater than those for a silicate crust experiencing the same impact history, on the basis of icy crust impact crater statistics.

Lange, Manfred A.↗
DOE OSTI2025

Nonthermal Ionization of Kilonova Ejecta: Observable Impacts

The characteristic rapid rise and decline at optical wavelengths of a kilonova is the product of the low ejecta mass (≲0.05 M ⊙ ) and high ejecta velocity (≳0.1c). We show that, even at very early times (≲2 days), regions of ejecta fall below critical density and temperature thresholds at which nonlocal thermodynamic equilibrium (NLTE) effects become important. Here, we present an approximate method for calculating the ionization state of the ejecta that accounts for the NLTE impact of high-energy electrons produced in the beta decay of freshly synthesized r-process elements. We find that incorporating ionization from high-energy electrons produces an “inverted” and “blended” ionization structure, where the most highly ionized species are located in the fastest moving homologous ejecta, and multiple ionization states coexist. In radiation transport calculations, the higher degree of ionization reduces line blanketing in optical bands, leading to improved agreement with the light-curve properties of AT 2017gfo, such as the duration, decay rates, brightness, and colors. Our quasi-NLTE implementation helps to alleviate tensions in kilonova modeling: for high-velocity (∼0.3 c) ejecta components, our models require less mass for a given peak brightness in optical bands, by as much as a factor of 3; our models can explain the presence of observed features associated to Sr II, W III, Se III, and Te III under conditions where LTE models would predict only neutral species; and we naturally predict the coexistence of species like Sr II and Ce III without the need for fine-tuning of the ejecta properties.

High energy astrophysics↗